blob: 75cc5a22da0c738cedcc921830582169a3829021 [file] [log] [blame]
Jeff Garzik669a5db2006-08-29 18:12:40 -04001/*
2 * ata-serverworks.c - Serverworks PATA for new ATA layer
3 * (C) 2005 Red Hat Inc
4 * Alan Cox <alan@redhat.com>
5 *
6 * based upon
7 *
8 * serverworks.c
Jeff Garzik85cd7252006-08-31 00:03:49 -04009 *
Jeff Garzik669a5db2006-08-29 18:12:40 -040010 * Copyright (C) 1998-2000 Michel Aubry
11 * Copyright (C) 1998-2000 Andrzej Krzysztofowicz
12 * Copyright (C) 1998-2000 Andre Hedrick <andre@linux-ide.org>
13 * Portions copyright (c) 2001 Sun Microsystems
14 *
15 *
16 * RCC/ServerWorks IDE driver for Linux
17 *
18 * OSB4: `Open South Bridge' IDE Interface (fn 1)
19 * supports UDMA mode 2 (33 MB/s)
20 *
21 * CSB5: `Champion South Bridge' IDE Interface (fn 1)
22 * all revisions support UDMA mode 4 (66 MB/s)
23 * revision A2.0 and up support UDMA mode 5 (100 MB/s)
24 *
25 * *** The CSB5 does not provide ANY register ***
26 * *** to detect 80-conductor cable presence. ***
27 *
28 * CSB6: `Champion South Bridge' IDE Interface (optional: third channel)
29 *
30 * Documentation:
31 * Available under NDA only. Errata info very hard to get.
32 */
33
34#include <linux/kernel.h>
35#include <linux/module.h>
36#include <linux/pci.h>
37#include <linux/init.h>
38#include <linux/blkdev.h>
39#include <linux/delay.h>
40#include <scsi/scsi_host.h>
41#include <linux/libata.h>
42
43#define DRV_NAME "pata_serverworks"
Alan Cox68d0d7a2006-09-26 22:24:31 +010044#define DRV_VERSION "0.3.7"
Jeff Garzik669a5db2006-08-29 18:12:40 -040045
46#define SVWKS_CSB5_REVISION_NEW 0x92 /* min PCI_REVISION_ID for UDMA5 (A2.0) */
47#define SVWKS_CSB6_REVISION 0xa0 /* min PCI_REVISION_ID for UDMA4 (A1.0) */
48
49/* Seagate Barracuda ATA IV Family drives in UDMA mode 5
50 * can overrun their FIFOs when used with the CSB5 */
51
52static const char *csb_bad_ata100[] = {
53 "ST320011A",
54 "ST340016A",
55 "ST360021A",
56 "ST380021A",
57 NULL
58};
59
60/**
61 * dell_cable - Dell serverworks cable detection
62 * @ap: ATA port to do cable detect
63 *
64 * Dell hide the 40/80 pin select for their interfaces in the top two
Jeff Garzik85cd7252006-08-31 00:03:49 -040065 * bits of the subsystem ID.
Jeff Garzik669a5db2006-08-29 18:12:40 -040066 */
Jeff Garzik85cd7252006-08-31 00:03:49 -040067
Jeff Garzik669a5db2006-08-29 18:12:40 -040068static int dell_cable(struct ata_port *ap) {
69 struct pci_dev *pdev = to_pci_dev(ap->host->dev);
Jeff Garzik85cd7252006-08-31 00:03:49 -040070
Jeff Garzik669a5db2006-08-29 18:12:40 -040071 if (pdev->subsystem_device & (1 << (ap->port_no + 14)))
72 return ATA_CBL_PATA80;
73 return ATA_CBL_PATA40;
74}
75
76/**
77 * sun_cable - Sun Cobalt 'Alpine' cable detection
78 * @ap: ATA port to do cable select
79 *
80 * Cobalt CSB5 IDE hides the 40/80pin in the top two bits of the
81 * subsystem ID the same as dell. We could use one function but we may
82 * need to extend the Dell one in future
83 */
Jeff Garzik85cd7252006-08-31 00:03:49 -040084
Jeff Garzik669a5db2006-08-29 18:12:40 -040085static int sun_cable(struct ata_port *ap) {
86 struct pci_dev *pdev = to_pci_dev(ap->host->dev);
Jeff Garzik85cd7252006-08-31 00:03:49 -040087
Jeff Garzik669a5db2006-08-29 18:12:40 -040088 if (pdev->subsystem_device & (1 << (ap->port_no + 14)))
89 return ATA_CBL_PATA80;
90 return ATA_CBL_PATA40;
91}
92
93/**
94 * osb4_cable - OSB4 cable detect
95 * @ap: ATA port to check
96 *
97 * The OSB4 isn't UDMA66 capable so this is easy
98 */
99
100static int osb4_cable(struct ata_port *ap) {
101 return ATA_CBL_PATA40;
102}
103
104/**
105 * csb4_cable - CSB5/6 cable detect
106 * @ap: ATA port to check
107 *
108 * Serverworks default arrangement is to use the drive side detection
109 * only.
110 */
111
112static int csb_cable(struct ata_port *ap) {
113 return ATA_CBL_PATA80;
114}
115
116struct sv_cable_table {
117 int device;
118 int subvendor;
119 int (*cable_detect)(struct ata_port *ap);
120};
121
122/*
123 * Note that we don't copy the old serverworks code because the old
124 * code contains obvious mistakes
125 */
Jeff Garzik85cd7252006-08-31 00:03:49 -0400126
Jeff Garzik669a5db2006-08-29 18:12:40 -0400127static struct sv_cable_table cable_detect[] = {
128 { PCI_DEVICE_ID_SERVERWORKS_CSB5IDE, PCI_VENDOR_ID_DELL, dell_cable },
129 { PCI_DEVICE_ID_SERVERWORKS_CSB6IDE, PCI_VENDOR_ID_DELL, dell_cable },
130 { PCI_DEVICE_ID_SERVERWORKS_CSB5IDE, PCI_VENDOR_ID_SUN, sun_cable },
Alan Cox68d0d7a2006-09-26 22:24:31 +0100131 { PCI_DEVICE_ID_SERVERWORKS_OSB4IDE, PCI_ANY_ID, osb4_cable },
Jeff Garzik669a5db2006-08-29 18:12:40 -0400132 { PCI_DEVICE_ID_SERVERWORKS_CSB5IDE, PCI_ANY_ID, csb_cable },
133 { PCI_DEVICE_ID_SERVERWORKS_CSB6IDE, PCI_ANY_ID, csb_cable },
134 { PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2, PCI_ANY_ID, csb_cable },
135 { PCI_DEVICE_ID_SERVERWORKS_HT1000IDE, PCI_ANY_ID, csb_cable },
136 { }
137};
138
139/**
140 * serverworks_pre_reset - cable detection
141 * @ap: ATA port
142 *
Jeff Garzik85cd7252006-08-31 00:03:49 -0400143 * Perform cable detection according to the device and subvendor
Jeff Garzik669a5db2006-08-29 18:12:40 -0400144 * identifications
145 */
Jeff Garzik85cd7252006-08-31 00:03:49 -0400146
Jeff Garzik669a5db2006-08-29 18:12:40 -0400147static int serverworks_pre_reset(struct ata_port *ap) {
148 struct pci_dev *pdev = to_pci_dev(ap->host->dev);
149 struct sv_cable_table *cb = cable_detect;
150
151 while(cb->device) {
Jeff Garzik85cd7252006-08-31 00:03:49 -0400152 if (cb->device == pdev->device &&
Jeff Garzik669a5db2006-08-29 18:12:40 -0400153 (cb->subvendor == pdev->subsystem_vendor ||
154 cb->subvendor == PCI_ANY_ID)) {
155 ap->cbl = cb->cable_detect(ap);
156 return ata_std_prereset(ap);
157 }
158 cb++;
159 }
160
161 BUG();
162 return -1; /* kill compiler warning */
163}
164
165static void serverworks_error_handler(struct ata_port *ap)
166{
167 return ata_bmdma_drive_eh(ap, serverworks_pre_reset, ata_std_softreset, NULL, ata_std_postreset);
168}
169
170/**
171 * serverworks_is_csb - Check for CSB or OSB
172 * @pdev: PCI device to check
173 *
174 * Returns true if the device being checked is known to be a CSB
175 * series device.
176 */
Jeff Garzik85cd7252006-08-31 00:03:49 -0400177
Jeff Garzik669a5db2006-08-29 18:12:40 -0400178static u8 serverworks_is_csb(struct pci_dev *pdev)
179{
180 switch (pdev->device) {
181 case PCI_DEVICE_ID_SERVERWORKS_CSB5IDE:
182 case PCI_DEVICE_ID_SERVERWORKS_CSB6IDE:
183 case PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2:
184 case PCI_DEVICE_ID_SERVERWORKS_HT1000IDE:
185 return 1;
186 default:
187 break;
188 }
189 return 0;
190}
191
192/**
193 * serverworks_osb4_filter - mode selection filter
194 * @ap: ATA interface
195 * @adev: ATA device
196 *
197 * Filter the offered modes for the device to apply controller
198 * specific rules. OSB4 requires no UDMA for disks due to a FIFO
199 * bug we hit.
200 */
Jeff Garzik85cd7252006-08-31 00:03:49 -0400201
Jeff Garzik669a5db2006-08-29 18:12:40 -0400202static unsigned long serverworks_osb4_filter(const struct ata_port *ap, struct ata_device *adev, unsigned long mask)
203{
204 if (adev->class == ATA_DEV_ATA)
205 mask &= ~ATA_MASK_UDMA;
206 return ata_pci_default_filter(ap, adev, mask);
207}
208
209
210/**
211 * serverworks_csb_filter - mode selection filter
212 * @ap: ATA interface
213 * @adev: ATA device
214 *
215 * Check the blacklist and disable UDMA5 if matched
216 */
217
218static unsigned long serverworks_csb_filter(const struct ata_port *ap, struct ata_device *adev, unsigned long mask)
219{
220 const char *p;
221 char model_num[40];
222 int len, i;
223
Jeff Garzik85cd7252006-08-31 00:03:49 -0400224 /* Disk, UDMA */
Jeff Garzik669a5db2006-08-29 18:12:40 -0400225 if (adev->class != ATA_DEV_ATA)
226 return ata_pci_default_filter(ap, adev, mask);
227
228 /* Actually do need to check */
229 ata_id_string(adev->id, model_num, ATA_ID_PROD_OFS, sizeof(model_num));
230 /* Precuationary - why not do this in the libata core ?? */
Jeff Garzik85cd7252006-08-31 00:03:49 -0400231
Jeff Garzik669a5db2006-08-29 18:12:40 -0400232 len = strlen(model_num);
233 while ((len > 0) && (model_num[len - 1] == ' ')) {
234 len--;
235 model_num[len] = 0;
236 }
237
238 for(i = 0; (p = csb_bad_ata100[i]) != NULL; i++) {
239 if (!strncmp(p, model_num, len))
240 mask &= ~(0x1F << ATA_SHIFT_UDMA);
241 }
242 return ata_pci_default_filter(ap, adev, mask);
243}
244
245
246/**
247 * serverworks_set_piomode - set initial PIO mode data
248 * @ap: ATA interface
249 * @adev: ATA device
250 *
251 * Program the OSB4/CSB5 timing registers for PIO. The PIO register
252 * load is done as a simple lookup.
253 */
254static void serverworks_set_piomode(struct ata_port *ap, struct ata_device *adev)
255{
256 static const u8 pio_mode[] = { 0x5d, 0x47, 0x34, 0x22, 0x20 };
257 int offset = 1 + (2 * ap->port_no) - adev->devno;
258 int devbits = (2 * ap->port_no + adev->devno) * 4;
259 u16 csb5_pio;
260 struct pci_dev *pdev = to_pci_dev(ap->host->dev);
261 int pio = adev->pio_mode - XFER_PIO_0;
262
263 pci_write_config_byte(pdev, 0x40 + offset, pio_mode[pio]);
Jeff Garzik85cd7252006-08-31 00:03:49 -0400264
Jeff Garzik669a5db2006-08-29 18:12:40 -0400265 /* The OSB4 just requires the timing but the CSB series want the
266 mode number as well */
267 if (serverworks_is_csb(pdev)) {
268 pci_read_config_word(pdev, 0x4A, &csb5_pio);
269 csb5_pio &= ~(0x0F << devbits);
270 pci_write_config_byte(pdev, 0x4A, csb5_pio | (pio << devbits));
271 }
272}
273
274/**
275 * serverworks_set_dmamode - set initial DMA mode data
276 * @ap: ATA interface
277 * @adev: ATA device
278 *
279 * Program the MWDMA/UDMA modes for the serverworks OSB4/CSB5
280 * chipset. The MWDMA mode values are pulled from a lookup table
281 * while the chipset uses mode number for UDMA.
282 */
283
284static void serverworks_set_dmamode(struct ata_port *ap, struct ata_device *adev)
285{
286 static const u8 dma_mode[] = { 0x77, 0x21, 0x20 };
287 int offset = 1 + 2 * ap->port_no - adev->devno;
288 int devbits = (2 * ap->port_no + adev->devno);
289 u8 ultra;
290 u8 ultra_cfg;
291 struct pci_dev *pdev = to_pci_dev(ap->host->dev);
292
293 pci_read_config_byte(pdev, 0x54, &ultra_cfg);
294
295 if (adev->dma_mode >= XFER_UDMA_0) {
296 pci_write_config_byte(pdev, 0x44 + offset, 0x20);
297
298 pci_read_config_byte(pdev, 0x56 + ap->port_no, &ultra);
299 ultra &= ~(0x0F << (ap->port_no * 4));
300 ultra |= (adev->dma_mode - XFER_UDMA_0)
301 << (ap->port_no * 4);
302 pci_write_config_byte(pdev, 0x56 + ap->port_no, ultra);
303
304 ultra_cfg |= (1 << devbits);
305 } else {
Jeff Garzik85cd7252006-08-31 00:03:49 -0400306 pci_write_config_byte(pdev, 0x44 + offset,
Jeff Garzik669a5db2006-08-29 18:12:40 -0400307 dma_mode[adev->dma_mode - XFER_MW_DMA_0]);
308 ultra_cfg &= ~(1 << devbits);
309 }
310 pci_write_config_byte(pdev, 0x54, ultra_cfg);
311}
312
313static struct scsi_host_template serverworks_sht = {
314 .module = THIS_MODULE,
315 .name = DRV_NAME,
316 .ioctl = ata_scsi_ioctl,
317 .queuecommand = ata_scsi_queuecmd,
318 .can_queue = ATA_DEF_QUEUE,
319 .this_id = ATA_SHT_THIS_ID,
320 .sg_tablesize = LIBATA_MAX_PRD,
321 .max_sectors = ATA_MAX_SECTORS,
322 .cmd_per_lun = ATA_SHT_CMD_PER_LUN,
323 .emulated = ATA_SHT_EMULATED,
324 .use_clustering = ATA_SHT_USE_CLUSTERING,
325 .proc_name = DRV_NAME,
326 .dma_boundary = ATA_DMA_BOUNDARY,
327 .slave_configure = ata_scsi_slave_config,
328 .bios_param = ata_std_bios_param,
329};
330
331static struct ata_port_operations serverworks_osb4_port_ops = {
332 .port_disable = ata_port_disable,
333 .set_piomode = serverworks_set_piomode,
334 .set_dmamode = serverworks_set_dmamode,
335 .mode_filter = serverworks_osb4_filter,
Jeff Garzik85cd7252006-08-31 00:03:49 -0400336
Jeff Garzik669a5db2006-08-29 18:12:40 -0400337 .tf_load = ata_tf_load,
338 .tf_read = ata_tf_read,
339 .check_status = ata_check_status,
340 .exec_command = ata_exec_command,
341 .dev_select = ata_std_dev_select,
342
343 .freeze = ata_bmdma_freeze,
344 .thaw = ata_bmdma_thaw,
345 .error_handler = serverworks_error_handler,
346 .post_internal_cmd = ata_bmdma_post_internal_cmd,
347
348 .bmdma_setup = ata_bmdma_setup,
349 .bmdma_start = ata_bmdma_start,
350 .bmdma_stop = ata_bmdma_stop,
351 .bmdma_status = ata_bmdma_status,
352
353 .qc_prep = ata_qc_prep,
354 .qc_issue = ata_qc_issue_prot,
355 .eng_timeout = ata_eng_timeout,
356 .data_xfer = ata_pio_data_xfer,
Jeff Garzik85cd7252006-08-31 00:03:49 -0400357
Jeff Garzik669a5db2006-08-29 18:12:40 -0400358 .irq_handler = ata_interrupt,
359 .port_start = ata_port_start,
360 .port_stop = ata_port_stop,
361 .host_stop = ata_host_stop
Jeff Garzik85cd7252006-08-31 00:03:49 -0400362};
Jeff Garzik669a5db2006-08-29 18:12:40 -0400363
364static struct ata_port_operations serverworks_csb_port_ops = {
365 .port_disable = ata_port_disable,
366 .set_piomode = serverworks_set_piomode,
367 .set_dmamode = serverworks_set_dmamode,
368 .mode_filter = serverworks_csb_filter,
Jeff Garzik85cd7252006-08-31 00:03:49 -0400369
Jeff Garzik669a5db2006-08-29 18:12:40 -0400370 .tf_load = ata_tf_load,
371 .tf_read = ata_tf_read,
372 .check_status = ata_check_status,
373 .exec_command = ata_exec_command,
374 .dev_select = ata_std_dev_select,
375
376 .freeze = ata_bmdma_freeze,
377 .thaw = ata_bmdma_thaw,
378 .error_handler = serverworks_error_handler,
379 .post_internal_cmd = ata_bmdma_post_internal_cmd,
380
381 .bmdma_setup = ata_bmdma_setup,
382 .bmdma_start = ata_bmdma_start,
383 .bmdma_stop = ata_bmdma_stop,
384 .bmdma_status = ata_bmdma_status,
385
386 .qc_prep = ata_qc_prep,
387 .qc_issue = ata_qc_issue_prot,
388 .eng_timeout = ata_eng_timeout,
389 .data_xfer = ata_pio_data_xfer,
Jeff Garzik85cd7252006-08-31 00:03:49 -0400390
Jeff Garzik669a5db2006-08-29 18:12:40 -0400391 .irq_handler = ata_interrupt,
392 .port_start = ata_port_start,
393 .port_stop = ata_port_stop,
394 .host_stop = ata_host_stop
Jeff Garzik85cd7252006-08-31 00:03:49 -0400395};
Jeff Garzik669a5db2006-08-29 18:12:40 -0400396
397static int serverworks_fixup_osb4(struct pci_dev *pdev)
398{
399 u32 reg;
400 struct pci_dev *isa_dev = pci_get_device(PCI_VENDOR_ID_SERVERWORKS,
401 PCI_DEVICE_ID_SERVERWORKS_OSB4, NULL);
402 if (isa_dev) {
403 pci_read_config_dword(isa_dev, 0x64, &reg);
404 reg &= ~0x00002000; /* disable 600ns interrupt mask */
405 if (!(reg & 0x00004000))
406 printk(KERN_DEBUG DRV_NAME ": UDMA not BIOS enabled.\n");
407 reg |= 0x00004000; /* enable UDMA/33 support */
408 pci_write_config_dword(isa_dev, 0x64, reg);
409 pci_dev_put(isa_dev);
410 return 0;
411 }
412 printk(KERN_WARNING "ata_serverworks: Unable to find bridge.\n");
413 return -ENODEV;
414}
415
416static int serverworks_fixup_csb(struct pci_dev *pdev)
417{
418 u8 rev;
419 u8 btr;
Jeff Garzik85cd7252006-08-31 00:03:49 -0400420
Jeff Garzik669a5db2006-08-29 18:12:40 -0400421 pci_read_config_byte(pdev, PCI_REVISION_ID, &rev);
422
423 /* Third Channel Test */
424 if (!(PCI_FUNC(pdev->devfn) & 1)) {
425 struct pci_dev * findev = NULL;
426 u32 reg4c = 0;
427 findev = pci_get_device(PCI_VENDOR_ID_SERVERWORKS,
428 PCI_DEVICE_ID_SERVERWORKS_CSB5, NULL);
429 if (findev) {
430 pci_read_config_dword(findev, 0x4C, &reg4c);
431 reg4c &= ~0x000007FF;
432 reg4c |= 0x00000040;
433 reg4c |= 0x00000020;
434 pci_write_config_dword(findev, 0x4C, reg4c);
435 pci_dev_put(findev);
436 }
437 } else {
438 struct pci_dev * findev = NULL;
439 u8 reg41 = 0;
440
441 findev = pci_get_device(PCI_VENDOR_ID_SERVERWORKS,
442 PCI_DEVICE_ID_SERVERWORKS_CSB6, NULL);
443 if (findev) {
444 pci_read_config_byte(findev, 0x41, &reg41);
445 reg41 &= ~0x40;
446 pci_write_config_byte(findev, 0x41, reg41);
447 pci_dev_put(findev);
448 }
449 }
450 /* setup the UDMA Control register
451 *
452 * 1. clear bit 6 to enable DMA
453 * 2. enable DMA modes with bits 0-1
454 * 00 : legacy
455 * 01 : udma2
456 * 10 : udma2/udma4
457 * 11 : udma2/udma4/udma5
458 */
459 pci_read_config_byte(pdev, 0x5A, &btr);
460 btr &= ~0x40;
461 if (!(PCI_FUNC(pdev->devfn) & 1))
462 btr |= 0x2;
463 else
464 btr |= (rev >= SVWKS_CSB5_REVISION_NEW) ? 0x3 : 0x2;
465 pci_write_config_byte(pdev, 0x5A, btr);
Jeff Garzik85cd7252006-08-31 00:03:49 -0400466
Jeff Garzik669a5db2006-08-29 18:12:40 -0400467 return btr;
468}
469
470static void serverworks_fixup_ht1000(struct pci_dev *pdev)
471{
472 u8 btr;
473 /* Setup HT1000 SouthBridge Controller - Single Channel Only */
474 pci_read_config_byte(pdev, 0x5A, &btr);
475 btr &= ~0x40;
476 btr |= 0x3;
477 pci_write_config_byte(pdev, 0x5A, btr);
478}
479
480
481static int serverworks_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
482{
483 int ports = 2;
484 static struct ata_port_info info[4] = {
485 { /* OSB4 */
486 .sht = &serverworks_sht,
487 .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
488 .pio_mask = 0x1f,
489 .mwdma_mask = 0x07,
490 .udma_mask = 0x07,
491 .port_ops = &serverworks_osb4_port_ops
492 }, { /* OSB4 no UDMA */
493 .sht = &serverworks_sht,
494 .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
495 .pio_mask = 0x1f,
496 .mwdma_mask = 0x07,
497 .udma_mask = 0x00,
498 .port_ops = &serverworks_osb4_port_ops
499 }, { /* CSB5 */
500 .sht = &serverworks_sht,
501 .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
502 .pio_mask = 0x1f,
503 .mwdma_mask = 0x07,
504 .udma_mask = 0x1f,
505 .port_ops = &serverworks_csb_port_ops
506 }, { /* CSB5 - later revisions*/
507 .sht = &serverworks_sht,
508 .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
509 .pio_mask = 0x1f,
510 .mwdma_mask = 0x07,
511 .udma_mask = 0x3f,
512 .port_ops = &serverworks_csb_port_ops
513 }
514 };
515 static struct ata_port_info *port_info[2];
516 struct ata_port_info *devinfo = &info[id->driver_data];
Jeff Garzik85cd7252006-08-31 00:03:49 -0400517
Jeff Garzik669a5db2006-08-29 18:12:40 -0400518 /* Force master latency timer to 64 PCI clocks */
519 pci_write_config_byte(pdev, PCI_LATENCY_TIMER, 0x40);
520
521 /* OSB4 : South Bridge and IDE */
522 if (pdev->device == PCI_DEVICE_ID_SERVERWORKS_OSB4IDE) {
523 /* Select non UDMA capable OSB4 if we can't do fixups */
524 if ( serverworks_fixup_osb4(pdev) < 0)
525 devinfo = &info[1];
526 }
527 /* setup CSB5/CSB6 : South Bridge and IDE option RAID */
528 else if ((pdev->device == PCI_DEVICE_ID_SERVERWORKS_CSB5IDE) ||
529 (pdev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE) ||
530 (pdev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2)) {
Jeff Garzik85cd7252006-08-31 00:03:49 -0400531
Jeff Garzik669a5db2006-08-29 18:12:40 -0400532 /* If the returned btr is the newer revision then
533 select the right info block */
534 if (serverworks_fixup_csb(pdev) == 3)
535 devinfo = &info[3];
Jeff Garzik85cd7252006-08-31 00:03:49 -0400536
Jeff Garzik669a5db2006-08-29 18:12:40 -0400537 /* Is this the 3rd channel CSB6 IDE ? */
538 if (pdev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2)
539 ports = 1;
540 }
541 /* setup HT1000E */
542 else if (pdev->device == PCI_DEVICE_ID_SERVERWORKS_HT1000IDE)
543 serverworks_fixup_ht1000(pdev);
Jeff Garzik85cd7252006-08-31 00:03:49 -0400544
Jeff Garzik669a5db2006-08-29 18:12:40 -0400545 if (pdev->device == PCI_DEVICE_ID_SERVERWORKS_CSB5IDE)
546 ata_pci_clear_simplex(pdev);
Jeff Garzik85cd7252006-08-31 00:03:49 -0400547
Jeff Garzik669a5db2006-08-29 18:12:40 -0400548 port_info[0] = port_info[1] = devinfo;
549 return ata_pci_init_one(pdev, port_info, ports);
550}
551
552static struct pci_device_id serverworks[] = {
553 { PCI_DEVICE(PCI_VENDOR_ID_SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_OSB4IDE), 0},
554 { PCI_DEVICE(PCI_VENDOR_ID_SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_CSB5IDE), 2},
555 { PCI_DEVICE(PCI_VENDOR_ID_SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_CSB6IDE), 2},
556 { PCI_DEVICE(PCI_VENDOR_ID_SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2), 2},
557 { PCI_DEVICE(PCI_VENDOR_ID_SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_HT1000IDE), 2},
558 { 0, },
559};
560
561static struct pci_driver serverworks_pci_driver = {
562 .name = DRV_NAME,
563 .id_table = serverworks,
564 .probe = serverworks_init_one,
565 .remove = ata_pci_remove_one
566};
567
568static int __init serverworks_init(void)
569{
570 return pci_register_driver(&serverworks_pci_driver);
571}
572
573
574static void __exit serverworks_exit(void)
575{
576 pci_unregister_driver(&serverworks_pci_driver);
577}
578
579
580MODULE_AUTHOR("Alan Cox");
581MODULE_DESCRIPTION("low-level driver for Serverworks OSB4/CSB5/CSB6");
582MODULE_LICENSE("GPL");
583MODULE_DEVICE_TABLE(pci, serverworks);
584MODULE_VERSION(DRV_VERSION);
585
586module_init(serverworks_init);
587module_exit(serverworks_exit);