Bellido Nicolas | 038c5b6 | 2005-06-20 18:51:05 +0100 | [diff] [blame] | 1 | /* |
| 2 | * linux/include/asm-arm/arch-aaec2000/aaec2000.h |
| 3 | * |
| 4 | * AAEC-2000 registers definition |
| 5 | * |
| 6 | * Copyright (c) 2005 Nicolas Bellido Y Ortega |
| 7 | * |
| 8 | * This program is free software; you can redistribute it and/or modify |
| 9 | * it under the terms of the GNU General Public License version 2 as |
| 10 | * published by the Free Software Foundation. |
| 11 | */ |
| 12 | |
| 13 | #ifndef __ASM_ARCH_AAEC2000_H |
| 14 | #define __ASM_ARCH_AAEC2000_H |
| 15 | |
| 16 | #ifndef __ASM_ARCH_HARDWARE_H |
| 17 | #error You must include hardware.h not this file |
| 18 | #endif /* __ASM_ARCH_HARDWARE_H */ |
| 19 | |
Bellido Nicolas | 13b1d67 | 2005-10-28 16:51:40 +0100 | [diff] [blame] | 20 | /* Chip selects */ |
| 21 | #define AAEC_CS0 0x00000000 |
| 22 | #define AAEC_CS1 0x10000000 |
| 23 | #define AAEC_CS2 0x20000000 |
| 24 | #define AAEC_CS3 0x30000000 |
| 25 | |
Bellido Nicolas | 4a91ca2 | 2005-10-28 16:51:42 +0100 | [diff] [blame] | 26 | /* Flash */ |
| 27 | #define AAEC_FLASH_BASE AAEC_CS0 |
| 28 | #define AAEC_FLASH_SIZE SZ_64M |
Bellido Nicolas | 13b1d67 | 2005-10-28 16:51:40 +0100 | [diff] [blame] | 29 | |
Bellido Nicolas | 038c5b6 | 2005-06-20 18:51:05 +0100 | [diff] [blame] | 30 | /* Interrupt controller */ |
| 31 | #define IRQ_BASE __REG(0x80000500) |
| 32 | #define IRQ_INTSR __REG(0x80000500) /* Int Status Register */ |
| 33 | #define IRQ_INTRSR __REG(0x80000504) /* Int Raw (unmasked) Status */ |
| 34 | #define IRQ_INTENS __REG(0x80000508) /* Int Enable Set */ |
| 35 | #define IRQ_INTENC __REG(0x8000050c) /* Int Enable Clear */ |
| 36 | |
| 37 | /* UART 1 */ |
| 38 | #define UART1_BASE __REG(0x80000600) |
| 39 | #define UART1_DR __REG(0x80000600) /* Data/FIFO Register */ |
| 40 | #define UART1_LCR __REG(0x80000604) /* Link Control Register */ |
| 41 | #define UART1_BRCR __REG(0x80000608) /* Baud Rate Control Register */ |
| 42 | #define UART1_CR __REG(0x8000060c) /* Control Register */ |
| 43 | #define UART1_SR __REG(0x80000610) /* Status Register */ |
| 44 | #define UART1_INT __REG(0x80000614) /* Interrupt Status Register */ |
| 45 | #define UART1_INTM __REG(0x80000618) /* Interrupt Mask Register */ |
| 46 | #define UART1_INTRES __REG(0x8000061c) /* Int Result (masked status) Register */ |
| 47 | |
| 48 | /* UART 2 */ |
| 49 | #define UART2_BASE __REG(0x80000700) |
| 50 | #define UART2_DR __REG(0x80000700) /* Data/FIFO Register */ |
| 51 | #define UART2_LCR __REG(0x80000704) /* Link Control Register */ |
| 52 | #define UART2_BRCR __REG(0x80000708) /* Baud Rate Control Register */ |
| 53 | #define UART2_CR __REG(0x8000070c) /* Control Register */ |
| 54 | #define UART2_SR __REG(0x80000710) /* Status Register */ |
| 55 | #define UART2_INT __REG(0x80000714) /* Interrupt Status Register */ |
| 56 | #define UART2_INTM __REG(0x80000718) /* Interrupt Mask Register */ |
| 57 | #define UART2_INTRES __REG(0x8000071c) /* Int Result (masked status) Register */ |
| 58 | |
| 59 | /* UART 3 */ |
| 60 | #define UART3_BASE __REG(0x80000800) |
| 61 | #define UART3_DR __REG(0x80000800) /* Data/FIFO Register */ |
| 62 | #define UART3_LCR __REG(0x80000804) /* Link Control Register */ |
| 63 | #define UART3_BRCR __REG(0x80000808) /* Baud Rate Control Register */ |
| 64 | #define UART3_CR __REG(0x8000080c) /* Control Register */ |
| 65 | #define UART3_SR __REG(0x80000810) /* Status Register */ |
| 66 | #define UART3_INT __REG(0x80000814) /* Interrupt Status Register */ |
| 67 | #define UART3_INTM __REG(0x80000818) /* Interrupt Mask Register */ |
| 68 | #define UART3_INTRES __REG(0x8000081c) /* Int Result (masked status) Register */ |
| 69 | |
| 70 | /* These are used in some places */ |
| 71 | #define _UART1_BASE __PREG(UART1_BASE) |
| 72 | #define _UART2_BASE __PREG(UART2_BASE) |
| 73 | #define _UART3_BASE __PREG(UART3_BASE) |
| 74 | |
| 75 | /* UART Registers Offsets */ |
| 76 | #define UART_DR 0x00 |
| 77 | #define UART_LCR 0x04 |
| 78 | #define UART_BRCR 0x08 |
| 79 | #define UART_CR 0x0c |
| 80 | #define UART_SR 0x10 |
| 81 | #define UART_INT 0x14 |
| 82 | #define UART_INTM 0x18 |
| 83 | #define UART_INTRES 0x1c |
| 84 | |
| 85 | /* UART_LCR Bitmask */ |
| 86 | #define UART_LCR_BRK (1 << 0) /* Send Break */ |
| 87 | #define UART_LCR_PEN (1 << 1) /* Parity Enable */ |
| 88 | #define UART_LCR_EP (1 << 2) /* Even/Odd Parity */ |
| 89 | #define UART_LCR_S2 (1 << 3) /* One/Two Stop bits */ |
| 90 | #define UART_LCR_FIFO (1 << 4) /* FIFO Enable */ |
| 91 | #define UART_LCR_WL5 (0 << 5) /* Word Length - 5 bits */ |
| 92 | #define UART_LCR_WL6 (1 << 5) /* Word Length - 6 bits */ |
| 93 | #define UART_LCR_WL7 (1 << 6) /* Word Length - 7 bits */ |
| 94 | #define UART_LCR_WL8 (1 << 7) /* Word Length - 8 bits */ |
| 95 | |
| 96 | /* UART_CR Bitmask */ |
| 97 | #define UART_CR_EN (1 << 0) /* UART Enable */ |
| 98 | #define UART_CR_SIR (1 << 1) /* IrDA SIR Enable */ |
| 99 | #define UART_CR_SIRLP (1 << 2) /* Low Power IrDA Enable */ |
| 100 | #define UART_CR_RXP (1 << 3) /* Receive Pin Polarity */ |
| 101 | #define UART_CR_TXP (1 << 4) /* Transmit Pin Polarity */ |
| 102 | #define UART_CR_MXP (1 << 5) /* Modem Pin Polarity */ |
| 103 | #define UART_CR_LOOP (1 << 6) /* Loopback Mode */ |
| 104 | |
| 105 | /* UART_SR Bitmask */ |
| 106 | #define UART_SR_CTS (1 << 0) /* Clear To Send Status */ |
| 107 | #define UART_SR_DSR (1 << 1) /* Data Set Ready Status */ |
| 108 | #define UART_SR_DCD (1 << 2) /* Data Carrier Detect Status */ |
| 109 | #define UART_SR_TxBSY (1 << 3) /* Transmitter Busy Status */ |
| 110 | #define UART_SR_RxFE (1 << 4) /* Receive FIFO Empty Status */ |
| 111 | #define UART_SR_TxFF (1 << 5) /* Transmit FIFO Full Status */ |
| 112 | #define UART_SR_RxFF (1 << 6) /* Receive FIFO Full Status */ |
| 113 | #define UART_SR_TxFE (1 << 7) /* Transmit FIFO Empty Status */ |
| 114 | |
| 115 | /* UART_INT Bitmask */ |
| 116 | #define UART_INT_RIS (1 << 0) /* Rx Interrupt */ |
| 117 | #define UART_INT_TIS (1 << 1) /* Tx Interrupt */ |
| 118 | #define UART_INT_MIS (1 << 2) /* Modem Interrupt */ |
| 119 | #define UART_INT_RTIS (1 << 3) /* Receive Timeout Interrupt */ |
| 120 | |
| 121 | /* Timer 1 */ |
| 122 | #define TIMER1_BASE __REG(0x80000c00) |
| 123 | #define TIMER1_LOAD __REG(0x80000c00) /* Timer 1 Load Register */ |
| 124 | #define TIMER1_VAL __REG(0x80000c04) /* Timer 1 Value Register */ |
| 125 | #define TIMER1_CTRL __REG(0x80000c08) /* Timer 1 Control Register */ |
| 126 | #define TIMER1_CLEAR __REG(0x80000c0c) /* Timer 1 Clear Register */ |
| 127 | |
| 128 | /* Timer 2 */ |
| 129 | #define TIMER2_BASE __REG(0x80000d00) |
| 130 | #define TIMER2_LOAD __REG(0x80000d00) /* Timer 2 Load Register */ |
| 131 | #define TIMER2_VAL __REG(0x80000d04) /* Timer 2 Value Register */ |
| 132 | #define TIMER2_CTRL __REG(0x80000d08) /* Timer 2 Control Register */ |
| 133 | #define TIMER2_CLEAR __REG(0x80000d0c) /* Timer 2 Clear Register */ |
| 134 | |
| 135 | /* Timer 3 */ |
| 136 | #define TIMER3_BASE __REG(0x80000e00) |
| 137 | #define TIMER3_LOAD __REG(0x80000e00) /* Timer 3 Load Register */ |
| 138 | #define TIMER3_VAL __REG(0x80000e04) /* Timer 3 Value Register */ |
| 139 | #define TIMER3_CTRL __REG(0x80000e08) /* Timer 3 Control Register */ |
| 140 | #define TIMER3_CLEAR __REG(0x80000e0c) /* Timer 3 Clear Register */ |
| 141 | |
| 142 | /* Timer Control register bits */ |
| 143 | #define TIMER_CTRL_ENABLE (1 << 7) /* Enable (Start° Timer */ |
| 144 | #define TIMER_CTRL_PERIODIC (1 << 6) /* Periodic Running Mode */ |
| 145 | #define TIMER_CTRL_FREE_RUNNING (0 << 6) /* Normal Running Mode */ |
| 146 | #define TIMER_CTRL_CLKSEL_508K (1 << 3) /* 508KHz Clock select (Timer 1, 2) */ |
| 147 | #define TIMER_CTRL_CLKSEL_2K (0 << 3) /* 2KHz Clock Select (Timer 1, 2)*/ |
| 148 | |
| 149 | /* Power and State Control */ |
| 150 | #define POWER_BASE __REG(0x80000400) |
| 151 | #define POWER_PWRSR __REG(0x80000400) /* Power Status Register */ |
| 152 | #define POWER_PWRCNT __REG(0x80000404) /* Power/Clock control */ |
| 153 | #define POWER_HALT __REG(0x80000408) /* Power Idle Mode */ |
| 154 | #define POWER_STDBY __REG(0x8000040c) /* Power Standby Mode */ |
| 155 | #define POWER_BLEOI __REG(0x80000410) /* Battery Low End of Interrupt */ |
| 156 | #define POWER_MCEOI __REG(0x80000414) /* Media Changed EoI */ |
| 157 | #define POWER_TEOI __REG(0x80000418) /* Tick EoI */ |
| 158 | #define POWER_STFCLR __REG(0x8000041c) /* NbFlg, RSTFlg, PFFlg, CLDFlg Clear */ |
| 159 | #define POWER_CLKSET __REG(0x80000420) /* Clock Speed Control */ |
| 160 | |
Bellido Nicolas | 13b1d67 | 2005-10-28 16:51:40 +0100 | [diff] [blame] | 161 | /* GPIO Registers */ |
| 162 | #define AAEC_GPIO_PHYS 0x80000e00 |
| 163 | |
| 164 | #define AAEC_GPIO_PADR __REG(AAEC_GPIO_PHYS + 0x00) |
| 165 | #define AAEC_GPIO_PBDR __REG(AAEC_GPIO_PHYS + 0x04) |
| 166 | #define AAEC_GPIO_PCDR __REG(AAEC_GPIO_PHYS + 0x08) |
| 167 | #define AAEC_GPIO_PDDR __REG(AAEC_GPIO_PHYS + 0x0c) |
| 168 | #define AAEC_GPIO_PADDR __REG(AAEC_GPIO_PHYS + 0x10) |
| 169 | #define AAEC_GPIO_PBDDR __REG(AAEC_GPIO_PHYS + 0x14) |
| 170 | #define AAEC_GPIO_PCDDR __REG(AAEC_GPIO_PHYS + 0x18) |
| 171 | #define AAEC_GPIO_PDDDR __REG(AAEC_GPIO_PHYS + 0x1c) |
| 172 | #define AAEC_GPIO_PEDR __REG(AAEC_GPIO_PHYS + 0x20) |
| 173 | #define AAEC_GPIO_PEDDR __REG(AAEC_GPIO_PHYS + 0x24) |
| 174 | #define AAEC_GPIO_KSCAN __REG(AAEC_GPIO_PHYS + 0x28) |
| 175 | #define AAEC_GPIO_PINMUX __REG(AAEC_GPIO_PHYS + 0x2c) |
| 176 | #define AAEC_GPIO_PFDR __REG(AAEC_GPIO_PHYS + 0x30) |
| 177 | #define AAEC_GPIO_PFDDR __REG(AAEC_GPIO_PHYS + 0x34) |
| 178 | #define AAEC_GPIO_PGDR __REG(AAEC_GPIO_PHYS + 0x38) |
| 179 | #define AAEC_GPIO_PGDDR __REG(AAEC_GPIO_PHYS + 0x3c) |
| 180 | #define AAEC_GPIO_PHDR __REG(AAEC_GPIO_PHYS + 0x40) |
| 181 | #define AAEC_GPIO_PHDDR __REG(AAEC_GPIO_PHYS + 0x44) |
| 182 | #define AAEC_GPIO_RAZ __REG(AAEC_GPIO_PHYS + 0x48) |
| 183 | #define AAEC_GPIO_INTTYPE1 __REG(AAEC_GPIO_PHYS + 0x4c) |
| 184 | #define AAEC_GPIO_INTTYPE2 __REG(AAEC_GPIO_PHYS + 0x50) |
| 185 | #define AAEC_GPIO_FEOI __REG(AAEC_GPIO_PHYS + 0x54) |
| 186 | #define AAEC_GPIO_INTEN __REG(AAEC_GPIO_PHYS + 0x58) |
| 187 | #define AAEC_GPIO_INTSTATUS __REG(AAEC_GPIO_PHYS + 0x5c) |
| 188 | #define AAEC_GPIO_RAWINTSTATUS __REG(AAEC_GPIO_PHYS + 0x60) |
| 189 | #define AAEC_GPIO_DB __REG(AAEC_GPIO_PHYS + 0x64) |
| 190 | #define AAEC_GPIO_PAPINDR __REG(AAEC_GPIO_PHYS + 0x68) |
| 191 | #define AAEC_GPIO_PBPINDR __REG(AAEC_GPIO_PHYS + 0x6c) |
| 192 | #define AAEC_GPIO_PCPINDR __REG(AAEC_GPIO_PHYS + 0x70) |
| 193 | #define AAEC_GPIO_PDPINDR __REG(AAEC_GPIO_PHYS + 0x74) |
| 194 | #define AAEC_GPIO_PEPINDR __REG(AAEC_GPIO_PHYS + 0x78) |
| 195 | #define AAEC_GPIO_PFPINDR __REG(AAEC_GPIO_PHYS + 0x7c) |
| 196 | #define AAEC_GPIO_PGPINDR __REG(AAEC_GPIO_PHYS + 0x80) |
| 197 | #define AAEC_GPIO_PHPINDR __REG(AAEC_GPIO_PHYS + 0x84) |
| 198 | |
| 199 | #define AAEC_GPIO_PINMUX_PE0CON (1 << 0) |
| 200 | #define AAEC_GPIO_PINMUX_PD0CON (1 << 1) |
| 201 | #define AAEC_GPIO_PINMUX_CODECON (1 << 2) |
| 202 | #define AAEC_GPIO_PINMUX_UART3CON (1 << 3) |
| 203 | |
Bellido Nicolas | 049eb32 | 2005-10-28 16:51:44 +0100 | [diff] [blame] | 204 | /* LCD Controller */ |
| 205 | #define AAEC_CLCD_PHYS 0x80003000 |
| 206 | |
Bellido Nicolas | 038c5b6 | 2005-06-20 18:51:05 +0100 | [diff] [blame] | 207 | #endif /* __ARM_ARCH_AAEC2000_H */ |