blob: e8a26f25d5c0a1464ab259c545e2b1d2031a9741 [file] [log] [blame]
Mika Westerbergcd7bed02013-01-22 12:26:28 +02001/*
2 * PXA2xx SPI private DMA support.
3 *
4 * Copyright (C) 2005 Stephen Street / StreetFire Sound Labs
5 *
6 * This program is free software; you can redistribute it and/or modify
7 * it under the terms of the GNU General Public License as published by
8 * the Free Software Foundation; either version 2 of the License, or
9 * (at your option) any later version.
10 *
11 * This program is distributed in the hope that it will be useful,
12 * but WITHOUT ANY WARRANTY; without even the implied warranty of
13 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
14 * GNU General Public License for more details.
15 *
16 * You should have received a copy of the GNU General Public License
17 * along with this program; if not, write to the Free Software
18 * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
19 */
20
Mika Westerbergcd7bed02013-01-22 12:26:28 +020021#include <linux/delay.h>
22#include <linux/device.h>
23#include <linux/dma-mapping.h>
24#include <linux/pxa2xx_ssp.h>
25#include <linux/spi/spi.h>
26#include <linux/spi/pxa2xx_spi.h>
27
28#include "spi-pxa2xx.h"
29
30#define DMA_INT_MASK (DCSR_ENDINTR | DCSR_STARTINTR | DCSR_BUSERR)
31#define RESET_DMA_CHANNEL (DCSR_NODESC | DMA_INT_MASK)
32
33bool pxa2xx_spi_dma_is_possible(size_t len)
34{
35 /* Try to map dma buffer and do a dma transfer if successful, but
36 * only if the length is non-zero and less than MAX_DMA_LEN.
37 *
38 * Zero-length non-descriptor DMA is illegal on PXA2xx; force use
39 * of PIO instead. Care is needed above because the transfer may
40 * have have been passed with buffers that are already dma mapped.
41 * A zero-length transfer in PIO mode will not try to write/read
42 * to/from the buffers
43 *
44 * REVISIT large transfers are exactly where we most want to be
45 * using DMA. If this happens much, split those transfers into
46 * multiple DMA segments rather than forcing PIO.
47 */
48 return len > 0 && len <= MAX_DMA_LEN;
49}
50
51int pxa2xx_spi_map_dma_buffers(struct driver_data *drv_data)
52{
53 struct spi_message *msg = drv_data->cur_msg;
54 struct device *dev = &msg->spi->dev;
55
56 if (!drv_data->cur_chip->enable_dma)
57 return 0;
58
59 if (msg->is_dma_mapped)
60 return drv_data->rx_dma && drv_data->tx_dma;
61
62 if (!IS_DMA_ALIGNED(drv_data->rx) || !IS_DMA_ALIGNED(drv_data->tx))
63 return 0;
64
65 /* Modify setup if rx buffer is null */
66 if (drv_data->rx == NULL) {
67 *drv_data->null_dma_buf = 0;
68 drv_data->rx = drv_data->null_dma_buf;
69 drv_data->rx_map_len = 4;
70 } else
71 drv_data->rx_map_len = drv_data->len;
72
73
74 /* Modify setup if tx buffer is null */
75 if (drv_data->tx == NULL) {
76 *drv_data->null_dma_buf = 0;
77 drv_data->tx = drv_data->null_dma_buf;
78 drv_data->tx_map_len = 4;
79 } else
80 drv_data->tx_map_len = drv_data->len;
81
82 /* Stream map the tx buffer. Always do DMA_TO_DEVICE first
83 * so we flush the cache *before* invalidating it, in case
84 * the tx and rx buffers overlap.
85 */
86 drv_data->tx_dma = dma_map_single(dev, drv_data->tx,
87 drv_data->tx_map_len, DMA_TO_DEVICE);
88 if (dma_mapping_error(dev, drv_data->tx_dma))
89 return 0;
90
91 /* Stream map the rx buffer */
92 drv_data->rx_dma = dma_map_single(dev, drv_data->rx,
93 drv_data->rx_map_len, DMA_FROM_DEVICE);
94 if (dma_mapping_error(dev, drv_data->rx_dma)) {
95 dma_unmap_single(dev, drv_data->tx_dma,
96 drv_data->tx_map_len, DMA_TO_DEVICE);
97 return 0;
98 }
99
100 return 1;
101}
102
103static void pxa2xx_spi_unmap_dma_buffers(struct driver_data *drv_data)
104{
105 struct device *dev;
106
107 if (!drv_data->dma_mapped)
108 return;
109
110 if (!drv_data->cur_msg->is_dma_mapped) {
111 dev = &drv_data->cur_msg->spi->dev;
112 dma_unmap_single(dev, drv_data->rx_dma,
113 drv_data->rx_map_len, DMA_FROM_DEVICE);
114 dma_unmap_single(dev, drv_data->tx_dma,
115 drv_data->tx_map_len, DMA_TO_DEVICE);
116 }
117
118 drv_data->dma_mapped = 0;
119}
120
121static int wait_ssp_rx_stall(void const __iomem *ioaddr)
122{
123 unsigned long limit = loops_per_jiffy << 1;
124
125 while ((read_SSSR(ioaddr) & SSSR_BSY) && --limit)
126 cpu_relax();
127
128 return limit;
129}
130
131static int wait_dma_channel_stop(int channel)
132{
133 unsigned long limit = loops_per_jiffy << 1;
134
135 while (!(DCSR(channel) & DCSR_STOPSTATE) && --limit)
136 cpu_relax();
137
138 return limit;
139}
140
141static void pxa2xx_spi_dma_error_stop(struct driver_data *drv_data,
142 const char *msg)
143{
144 void __iomem *reg = drv_data->ioaddr;
145
146 /* Stop and reset */
147 DCSR(drv_data->rx_channel) = RESET_DMA_CHANNEL;
148 DCSR(drv_data->tx_channel) = RESET_DMA_CHANNEL;
149 write_SSSR_CS(drv_data, drv_data->clear_sr);
150 write_SSCR1(read_SSCR1(reg) & ~drv_data->dma_cr1, reg);
151 if (!pxa25x_ssp_comp(drv_data))
152 write_SSTO(0, reg);
153 pxa2xx_spi_flush(drv_data);
154 write_SSCR0(read_SSCR0(reg) & ~SSCR0_SSE, reg);
155
156 pxa2xx_spi_unmap_dma_buffers(drv_data);
157
158 dev_err(&drv_data->pdev->dev, "%s\n", msg);
159
160 drv_data->cur_msg->state = ERROR_STATE;
161 tasklet_schedule(&drv_data->pump_transfers);
162}
163
164static void pxa2xx_spi_dma_transfer_complete(struct driver_data *drv_data)
165{
166 void __iomem *reg = drv_data->ioaddr;
167 struct spi_message *msg = drv_data->cur_msg;
168
169 /* Clear and disable interrupts on SSP and DMA channels*/
170 write_SSCR1(read_SSCR1(reg) & ~drv_data->dma_cr1, reg);
171 write_SSSR_CS(drv_data, drv_data->clear_sr);
172 DCSR(drv_data->tx_channel) = RESET_DMA_CHANNEL;
173 DCSR(drv_data->rx_channel) = RESET_DMA_CHANNEL;
174
175 if (wait_dma_channel_stop(drv_data->rx_channel) == 0)
176 dev_err(&drv_data->pdev->dev,
177 "dma_handler: dma rx channel stop failed\n");
178
179 if (wait_ssp_rx_stall(drv_data->ioaddr) == 0)
180 dev_err(&drv_data->pdev->dev,
181 "dma_transfer: ssp rx stall failed\n");
182
183 pxa2xx_spi_unmap_dma_buffers(drv_data);
184
185 /* update the buffer pointer for the amount completed in dma */
186 drv_data->rx += drv_data->len -
187 (DCMD(drv_data->rx_channel) & DCMD_LENGTH);
188
189 /* read trailing data from fifo, it does not matter how many
190 * bytes are in the fifo just read until buffer is full
191 * or fifo is empty, which ever occurs first */
192 drv_data->read(drv_data);
193
194 /* return count of what was actually read */
195 msg->actual_length += drv_data->len -
196 (drv_data->rx_end - drv_data->rx);
197
198 /* Transfer delays and chip select release are
199 * handled in pump_transfers or giveback
200 */
201
202 /* Move to next transfer */
203 msg->state = pxa2xx_spi_next_transfer(drv_data);
204
205 /* Schedule transfer tasklet */
206 tasklet_schedule(&drv_data->pump_transfers);
207}
208
209void pxa2xx_spi_dma_handler(int channel, void *data)
210{
211 struct driver_data *drv_data = data;
212 u32 irq_status = DCSR(channel) & DMA_INT_MASK;
213
214 if (irq_status & DCSR_BUSERR) {
215
216 if (channel == drv_data->tx_channel)
217 pxa2xx_spi_dma_error_stop(drv_data,
218 "dma_handler: bad bus address on tx channel");
219 else
220 pxa2xx_spi_dma_error_stop(drv_data,
221 "dma_handler: bad bus address on rx channel");
222 return;
223 }
224
225 /* PXA255x_SSP has no timeout interrupt, wait for tailing bytes */
226 if ((channel == drv_data->tx_channel)
227 && (irq_status & DCSR_ENDINTR)
228 && (drv_data->ssp_type == PXA25x_SSP)) {
229
230 /* Wait for rx to stall */
231 if (wait_ssp_rx_stall(drv_data->ioaddr) == 0)
232 dev_err(&drv_data->pdev->dev,
233 "dma_handler: ssp rx stall failed\n");
234
235 /* finish this transfer, start the next */
236 pxa2xx_spi_dma_transfer_complete(drv_data);
237 }
238}
239
240irqreturn_t pxa2xx_spi_dma_transfer(struct driver_data *drv_data)
241{
242 u32 irq_status;
243 void __iomem *reg = drv_data->ioaddr;
244
245 irq_status = read_SSSR(reg) & drv_data->mask_sr;
246 if (irq_status & SSSR_ROR) {
247 pxa2xx_spi_dma_error_stop(drv_data,
248 "dma_transfer: fifo overrun");
249 return IRQ_HANDLED;
250 }
251
252 /* Check for false positive timeout */
253 if ((irq_status & SSSR_TINT)
254 && (DCSR(drv_data->tx_channel) & DCSR_RUN)) {
255 write_SSSR(SSSR_TINT, reg);
256 return IRQ_HANDLED;
257 }
258
259 if (irq_status & SSSR_TINT || drv_data->rx == drv_data->rx_end) {
260
261 /* Clear and disable timeout interrupt, do the rest in
262 * dma_transfer_complete */
263 if (!pxa25x_ssp_comp(drv_data))
264 write_SSTO(0, reg);
265
266 /* finish this transfer, start the next */
267 pxa2xx_spi_dma_transfer_complete(drv_data);
268
269 return IRQ_HANDLED;
270 }
271
272 /* Opps problem detected */
273 return IRQ_NONE;
274}
275
276int pxa2xx_spi_dma_prepare(struct driver_data *drv_data, u32 dma_burst)
277{
278 u32 dma_width;
279
280 switch (drv_data->n_bytes) {
281 case 1:
282 dma_width = DCMD_WIDTH1;
283 break;
284 case 2:
285 dma_width = DCMD_WIDTH2;
286 break;
287 default:
288 dma_width = DCMD_WIDTH4;
289 break;
290 }
291
292 /* Setup rx DMA Channel */
293 DCSR(drv_data->rx_channel) = RESET_DMA_CHANNEL;
294 DSADR(drv_data->rx_channel) = drv_data->ssdr_physical;
295 DTADR(drv_data->rx_channel) = drv_data->rx_dma;
296 if (drv_data->rx == drv_data->null_dma_buf)
297 /* No target address increment */
298 DCMD(drv_data->rx_channel) = DCMD_FLOWSRC
299 | dma_width
300 | dma_burst
301 | drv_data->len;
302 else
303 DCMD(drv_data->rx_channel) = DCMD_INCTRGADDR
304 | DCMD_FLOWSRC
305 | dma_width
306 | dma_burst
307 | drv_data->len;
308
309 /* Setup tx DMA Channel */
310 DCSR(drv_data->tx_channel) = RESET_DMA_CHANNEL;
311 DSADR(drv_data->tx_channel) = drv_data->tx_dma;
312 DTADR(drv_data->tx_channel) = drv_data->ssdr_physical;
313 if (drv_data->tx == drv_data->null_dma_buf)
314 /* No source address increment */
315 DCMD(drv_data->tx_channel) = DCMD_FLOWTRG
316 | dma_width
317 | dma_burst
318 | drv_data->len;
319 else
320 DCMD(drv_data->tx_channel) = DCMD_INCSRCADDR
321 | DCMD_FLOWTRG
322 | dma_width
323 | dma_burst
324 | drv_data->len;
325
326 /* Enable dma end irqs on SSP to detect end of transfer */
327 if (drv_data->ssp_type == PXA25x_SSP)
328 DCMD(drv_data->tx_channel) |= DCMD_ENDIRQEN;
329
330 return 0;
331}
332
333void pxa2xx_spi_dma_start(struct driver_data *drv_data)
334{
335 DCSR(drv_data->rx_channel) |= DCSR_RUN;
336 DCSR(drv_data->tx_channel) |= DCSR_RUN;
337}
338
339int pxa2xx_spi_dma_setup(struct driver_data *drv_data)
340{
341 struct device *dev = &drv_data->pdev->dev;
342 struct ssp_device *ssp = drv_data->ssp;
343
344 /* Get two DMA channels (rx and tx) */
345 drv_data->rx_channel = pxa_request_dma("pxa2xx_spi_ssp_rx",
346 DMA_PRIO_HIGH,
347 pxa2xx_spi_dma_handler,
348 drv_data);
349 if (drv_data->rx_channel < 0) {
350 dev_err(dev, "problem (%d) requesting rx channel\n",
351 drv_data->rx_channel);
352 return -ENODEV;
353 }
354 drv_data->tx_channel = pxa_request_dma("pxa2xx_spi_ssp_tx",
355 DMA_PRIO_MEDIUM,
356 pxa2xx_spi_dma_handler,
357 drv_data);
358 if (drv_data->tx_channel < 0) {
359 dev_err(dev, "problem (%d) requesting tx channel\n",
360 drv_data->tx_channel);
361 pxa_free_dma(drv_data->rx_channel);
362 return -ENODEV;
363 }
364
365 DRCMR(ssp->drcmr_rx) = DRCMR_MAPVLD | drv_data->rx_channel;
366 DRCMR(ssp->drcmr_tx) = DRCMR_MAPVLD | drv_data->tx_channel;
367
368 return 0;
369}
370
371void pxa2xx_spi_dma_release(struct driver_data *drv_data)
372{
373 struct ssp_device *ssp = drv_data->ssp;
374
375 DRCMR(ssp->drcmr_rx) = 0;
376 DRCMR(ssp->drcmr_tx) = 0;
377
378 if (drv_data->tx_channel != 0)
379 pxa_free_dma(drv_data->tx_channel);
380 if (drv_data->rx_channel != 0)
381 pxa_free_dma(drv_data->rx_channel);
382}
383
384void pxa2xx_spi_dma_resume(struct driver_data *drv_data)
385{
386 if (drv_data->rx_channel != -1)
387 DRCMR(drv_data->ssp->drcmr_rx) =
388 DRCMR_MAPVLD | drv_data->rx_channel;
389 if (drv_data->tx_channel != -1)
390 DRCMR(drv_data->ssp->drcmr_tx) =
391 DRCMR_MAPVLD | drv_data->tx_channel;
392}
393
394int pxa2xx_spi_set_dma_burst_and_threshold(struct chip_data *chip,
395 struct spi_device *spi,
396 u8 bits_per_word, u32 *burst_code,
397 u32 *threshold)
398{
399 struct pxa2xx_spi_chip *chip_info =
400 (struct pxa2xx_spi_chip *)spi->controller_data;
401 int bytes_per_word;
402 int burst_bytes;
403 int thresh_words;
404 int req_burst_size;
405 int retval = 0;
406
407 /* Set the threshold (in registers) to equal the same amount of data
408 * as represented by burst size (in bytes). The computation below
409 * is (burst_size rounded up to nearest 8 byte, word or long word)
410 * divided by (bytes/register); the tx threshold is the inverse of
411 * the rx, so that there will always be enough data in the rx fifo
412 * to satisfy a burst, and there will always be enough space in the
413 * tx fifo to accept a burst (a tx burst will overwrite the fifo if
414 * there is not enough space), there must always remain enough empty
415 * space in the rx fifo for any data loaded to the tx fifo.
416 * Whenever burst_size (in bytes) equals bits/word, the fifo threshold
417 * will be 8, or half the fifo;
418 * The threshold can only be set to 2, 4 or 8, but not 16, because
419 * to burst 16 to the tx fifo, the fifo would have to be empty;
420 * however, the minimum fifo trigger level is 1, and the tx will
421 * request service when the fifo is at this level, with only 15 spaces.
422 */
423
424 /* find bytes/word */
425 if (bits_per_word <= 8)
426 bytes_per_word = 1;
427 else if (bits_per_word <= 16)
428 bytes_per_word = 2;
429 else
430 bytes_per_word = 4;
431
432 /* use struct pxa2xx_spi_chip->dma_burst_size if available */
433 if (chip_info)
434 req_burst_size = chip_info->dma_burst_size;
435 else {
436 switch (chip->dma_burst_size) {
437 default:
438 /* if the default burst size is not set,
439 * do it now */
440 chip->dma_burst_size = DCMD_BURST8;
441 case DCMD_BURST8:
442 req_burst_size = 8;
443 break;
444 case DCMD_BURST16:
445 req_burst_size = 16;
446 break;
447 case DCMD_BURST32:
448 req_burst_size = 32;
449 break;
450 }
451 }
452 if (req_burst_size <= 8) {
453 *burst_code = DCMD_BURST8;
454 burst_bytes = 8;
455 } else if (req_burst_size <= 16) {
456 if (bytes_per_word == 1) {
457 /* don't burst more than 1/2 the fifo */
458 *burst_code = DCMD_BURST8;
459 burst_bytes = 8;
460 retval = 1;
461 } else {
462 *burst_code = DCMD_BURST16;
463 burst_bytes = 16;
464 }
465 } else {
466 if (bytes_per_word == 1) {
467 /* don't burst more than 1/2 the fifo */
468 *burst_code = DCMD_BURST8;
469 burst_bytes = 8;
470 retval = 1;
471 } else if (bytes_per_word == 2) {
472 /* don't burst more than 1/2 the fifo */
473 *burst_code = DCMD_BURST16;
474 burst_bytes = 16;
475 retval = 1;
476 } else {
477 *burst_code = DCMD_BURST32;
478 burst_bytes = 32;
479 }
480 }
481
482 thresh_words = burst_bytes / bytes_per_word;
483
484 /* thresh_words will be between 2 and 8 */
485 *threshold = (SSCR1_RxTresh(thresh_words) & SSCR1_RFT)
486 | (SSCR1_TxTresh(16-thresh_words) & SSCR1_TFT);
487
488 return retval;
489}