Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1 | /* |
| 2 | * arch/arm/mach-ixp4xx/common-pci.c |
| 3 | * |
| 4 | * IXP4XX PCI routines for all platforms |
| 5 | * |
| 6 | * Maintainer: Deepak Saxena <dsaxena@plexity.net> |
| 7 | * |
| 8 | * Copyright (C) 2002 Intel Corporation. |
| 9 | * Copyright (C) 2003 Greg Ungerer <gerg@snapgear.com> |
| 10 | * Copyright (C) 2003-2004 MontaVista Software, Inc. |
| 11 | * |
| 12 | * This program is free software; you can redistribute it and/or modify |
| 13 | * it under the terms of the GNU General Public License version 2 as |
| 14 | * published by the Free Software Foundation. |
| 15 | * |
| 16 | */ |
| 17 | |
| 18 | #include <linux/sched.h> |
| 19 | #include <linux/kernel.h> |
| 20 | #include <linux/pci.h> |
| 21 | #include <linux/interrupt.h> |
| 22 | #include <linux/mm.h> |
| 23 | #include <linux/init.h> |
| 24 | #include <linux/ioport.h> |
| 25 | #include <linux/slab.h> |
| 26 | #include <linux/delay.h> |
| 27 | #include <linux/device.h> |
| 28 | #include <asm/dma-mapping.h> |
| 29 | |
| 30 | #include <asm/io.h> |
| 31 | #include <asm/irq.h> |
| 32 | #include <asm/sizes.h> |
| 33 | #include <asm/system.h> |
| 34 | #include <asm/mach/pci.h> |
| 35 | #include <asm/hardware.h> |
| 36 | |
| 37 | |
| 38 | /* |
| 39 | * IXP4xx PCI read function is dependent on whether we are |
| 40 | * running A0 or B0 (AppleGate) silicon. |
| 41 | */ |
| 42 | int (*ixp4xx_pci_read)(u32 addr, u32 cmd, u32* data); |
| 43 | |
| 44 | /* |
| 45 | * Base address for PCI regsiter region |
| 46 | */ |
| 47 | unsigned long ixp4xx_pci_reg_base = 0; |
| 48 | |
| 49 | /* |
| 50 | * PCI cfg an I/O routines are done by programming a |
| 51 | * command/byte enable register, and then read/writing |
| 52 | * the data from a data regsiter. We need to ensure |
| 53 | * these transactions are atomic or we will end up |
| 54 | * with corrupt data on the bus or in a driver. |
| 55 | */ |
| 56 | static DEFINE_SPINLOCK(ixp4xx_pci_lock); |
| 57 | |
| 58 | /* |
| 59 | * Read from PCI config space |
| 60 | */ |
| 61 | static void crp_read(u32 ad_cbe, u32 *data) |
| 62 | { |
| 63 | unsigned long flags; |
| 64 | spin_lock_irqsave(&ixp4xx_pci_lock, flags); |
| 65 | *PCI_CRP_AD_CBE = ad_cbe; |
| 66 | *data = *PCI_CRP_RDATA; |
| 67 | spin_unlock_irqrestore(&ixp4xx_pci_lock, flags); |
| 68 | } |
| 69 | |
| 70 | /* |
| 71 | * Write to PCI config space |
| 72 | */ |
| 73 | static void crp_write(u32 ad_cbe, u32 data) |
| 74 | { |
| 75 | unsigned long flags; |
| 76 | spin_lock_irqsave(&ixp4xx_pci_lock, flags); |
| 77 | *PCI_CRP_AD_CBE = CRP_AD_CBE_WRITE | ad_cbe; |
| 78 | *PCI_CRP_WDATA = data; |
| 79 | spin_unlock_irqrestore(&ixp4xx_pci_lock, flags); |
| 80 | } |
| 81 | |
| 82 | static inline int check_master_abort(void) |
| 83 | { |
| 84 | /* check Master Abort bit after access */ |
| 85 | unsigned long isr = *PCI_ISR; |
| 86 | |
| 87 | if (isr & PCI_ISR_PFE) { |
| 88 | /* make sure the Master Abort bit is reset */ |
| 89 | *PCI_ISR = PCI_ISR_PFE; |
| 90 | pr_debug("%s failed\n", __FUNCTION__); |
| 91 | return 1; |
| 92 | } |
| 93 | |
| 94 | return 0; |
| 95 | } |
| 96 | |
| 97 | int ixp4xx_pci_read_errata(u32 addr, u32 cmd, u32* data) |
| 98 | { |
| 99 | unsigned long flags; |
| 100 | int retval = 0; |
| 101 | int i; |
| 102 | |
| 103 | spin_lock_irqsave(&ixp4xx_pci_lock, flags); |
| 104 | |
| 105 | *PCI_NP_AD = addr; |
| 106 | |
| 107 | /* |
| 108 | * PCI workaround - only works if NP PCI space reads have |
| 109 | * no side effects!!! Read 8 times. last one will be good. |
| 110 | */ |
| 111 | for (i = 0; i < 8; i++) { |
| 112 | *PCI_NP_CBE = cmd; |
| 113 | *data = *PCI_NP_RDATA; |
| 114 | *data = *PCI_NP_RDATA; |
| 115 | } |
| 116 | |
| 117 | if(check_master_abort()) |
| 118 | retval = 1; |
| 119 | |
| 120 | spin_unlock_irqrestore(&ixp4xx_pci_lock, flags); |
| 121 | return retval; |
| 122 | } |
| 123 | |
| 124 | int ixp4xx_pci_read_no_errata(u32 addr, u32 cmd, u32* data) |
| 125 | { |
| 126 | unsigned long flags; |
| 127 | int retval = 0; |
| 128 | |
| 129 | spin_lock_irqsave(&ixp4xx_pci_lock, flags); |
| 130 | |
| 131 | *PCI_NP_AD = addr; |
| 132 | |
| 133 | /* set up and execute the read */ |
| 134 | *PCI_NP_CBE = cmd; |
| 135 | |
| 136 | /* the result of the read is now in NP_RDATA */ |
| 137 | *data = *PCI_NP_RDATA; |
| 138 | |
| 139 | if(check_master_abort()) |
| 140 | retval = 1; |
| 141 | |
| 142 | spin_unlock_irqrestore(&ixp4xx_pci_lock, flags); |
| 143 | return retval; |
| 144 | } |
| 145 | |
| 146 | int ixp4xx_pci_write(u32 addr, u32 cmd, u32 data) |
| 147 | { |
| 148 | unsigned long flags; |
| 149 | int retval = 0; |
| 150 | |
| 151 | spin_lock_irqsave(&ixp4xx_pci_lock, flags); |
| 152 | |
| 153 | *PCI_NP_AD = addr; |
| 154 | |
| 155 | /* set up the write */ |
| 156 | *PCI_NP_CBE = cmd; |
| 157 | |
| 158 | /* execute the write by writing to NP_WDATA */ |
| 159 | *PCI_NP_WDATA = data; |
| 160 | |
| 161 | if(check_master_abort()) |
| 162 | retval = 1; |
| 163 | |
| 164 | spin_unlock_irqrestore(&ixp4xx_pci_lock, flags); |
| 165 | return retval; |
| 166 | } |
| 167 | |
| 168 | static u32 ixp4xx_config_addr(u8 bus_num, u16 devfn, int where) |
| 169 | { |
| 170 | u32 addr; |
| 171 | if (!bus_num) { |
| 172 | /* type 0 */ |
| 173 | addr = BIT(32-PCI_SLOT(devfn)) | ((PCI_FUNC(devfn)) << 8) | |
| 174 | (where & ~3); |
| 175 | } else { |
| 176 | /* type 1 */ |
| 177 | addr = (bus_num << 16) | ((PCI_SLOT(devfn)) << 11) | |
| 178 | ((PCI_FUNC(devfn)) << 8) | (where & ~3) | 1; |
| 179 | } |
| 180 | return addr; |
| 181 | } |
| 182 | |
| 183 | /* |
| 184 | * Mask table, bits to mask for quantity of size 1, 2 or 4 bytes. |
| 185 | * 0 and 3 are not valid indexes... |
| 186 | */ |
| 187 | static u32 bytemask[] = { |
| 188 | /*0*/ 0, |
| 189 | /*1*/ 0xff, |
| 190 | /*2*/ 0xffff, |
| 191 | /*3*/ 0, |
| 192 | /*4*/ 0xffffffff, |
| 193 | }; |
| 194 | |
| 195 | static u32 local_byte_lane_enable_bits(u32 n, int size) |
| 196 | { |
| 197 | if (size == 1) |
| 198 | return (0xf & ~BIT(n)) << CRP_AD_CBE_BESL; |
| 199 | if (size == 2) |
| 200 | return (0xf & ~(BIT(n) | BIT(n+1))) << CRP_AD_CBE_BESL; |
| 201 | if (size == 4) |
| 202 | return 0; |
| 203 | return 0xffffffff; |
| 204 | } |
| 205 | |
| 206 | static int local_read_config(int where, int size, u32 *value) |
| 207 | { |
| 208 | u32 n, data; |
| 209 | pr_debug("local_read_config from %d size %d\n", where, size); |
| 210 | n = where % 4; |
| 211 | crp_read(where & ~3, &data); |
| 212 | *value = (data >> (8*n)) & bytemask[size]; |
| 213 | pr_debug("local_read_config read %#x\n", *value); |
| 214 | return PCIBIOS_SUCCESSFUL; |
| 215 | } |
| 216 | |
| 217 | static int local_write_config(int where, int size, u32 value) |
| 218 | { |
| 219 | u32 n, byte_enables, data; |
| 220 | pr_debug("local_write_config %#x to %d size %d\n", value, where, size); |
| 221 | n = where % 4; |
| 222 | byte_enables = local_byte_lane_enable_bits(n, size); |
| 223 | if (byte_enables == 0xffffffff) |
| 224 | return PCIBIOS_BAD_REGISTER_NUMBER; |
| 225 | data = value << (8*n); |
| 226 | crp_write((where & ~3) | byte_enables, data); |
| 227 | return PCIBIOS_SUCCESSFUL; |
| 228 | } |
| 229 | |
| 230 | static u32 byte_lane_enable_bits(u32 n, int size) |
| 231 | { |
| 232 | if (size == 1) |
| 233 | return (0xf & ~BIT(n)) << 4; |
| 234 | if (size == 2) |
| 235 | return (0xf & ~(BIT(n) | BIT(n+1))) << 4; |
| 236 | if (size == 4) |
| 237 | return 0; |
| 238 | return 0xffffffff; |
| 239 | } |
| 240 | |
| 241 | static int ixp4xx_pci_read_config(struct pci_bus *bus, unsigned int devfn, int where, int size, u32 *value) |
| 242 | { |
| 243 | u32 n, byte_enables, addr, data; |
| 244 | u8 bus_num = bus->number; |
| 245 | |
| 246 | pr_debug("read_config from %d size %d dev %d:%d:%d\n", where, size, |
| 247 | bus_num, PCI_SLOT(devfn), PCI_FUNC(devfn)); |
| 248 | |
| 249 | *value = 0xffffffff; |
| 250 | n = where % 4; |
| 251 | byte_enables = byte_lane_enable_bits(n, size); |
| 252 | if (byte_enables == 0xffffffff) |
| 253 | return PCIBIOS_BAD_REGISTER_NUMBER; |
| 254 | |
| 255 | addr = ixp4xx_config_addr(bus_num, devfn, where); |
| 256 | if (ixp4xx_pci_read(addr, byte_enables | NP_CMD_CONFIGREAD, &data)) |
| 257 | return PCIBIOS_DEVICE_NOT_FOUND; |
| 258 | |
| 259 | *value = (data >> (8*n)) & bytemask[size]; |
| 260 | pr_debug("read_config_byte read %#x\n", *value); |
| 261 | return PCIBIOS_SUCCESSFUL; |
| 262 | } |
| 263 | |
| 264 | static int ixp4xx_pci_write_config(struct pci_bus *bus, unsigned int devfn, int where, int size, u32 value) |
| 265 | { |
| 266 | u32 n, byte_enables, addr, data; |
| 267 | u8 bus_num = bus->number; |
| 268 | |
| 269 | pr_debug("write_config_byte %#x to %d size %d dev %d:%d:%d\n", value, where, |
| 270 | size, bus_num, PCI_SLOT(devfn), PCI_FUNC(devfn)); |
| 271 | |
| 272 | n = where % 4; |
| 273 | byte_enables = byte_lane_enable_bits(n, size); |
| 274 | if (byte_enables == 0xffffffff) |
| 275 | return PCIBIOS_BAD_REGISTER_NUMBER; |
| 276 | |
| 277 | addr = ixp4xx_config_addr(bus_num, devfn, where); |
| 278 | data = value << (8*n); |
| 279 | if (ixp4xx_pci_write(addr, byte_enables | NP_CMD_CONFIGWRITE, data)) |
| 280 | return PCIBIOS_DEVICE_NOT_FOUND; |
| 281 | |
| 282 | return PCIBIOS_SUCCESSFUL; |
| 283 | } |
| 284 | |
| 285 | struct pci_ops ixp4xx_ops = { |
| 286 | .read = ixp4xx_pci_read_config, |
| 287 | .write = ixp4xx_pci_write_config, |
| 288 | }; |
| 289 | |
| 290 | /* |
| 291 | * PCI abort handler |
| 292 | */ |
| 293 | static int abort_handler(unsigned long addr, unsigned int fsr, struct pt_regs *regs) |
| 294 | { |
| 295 | u32 isr, status; |
| 296 | |
| 297 | isr = *PCI_ISR; |
| 298 | local_read_config(PCI_STATUS, 2, &status); |
| 299 | pr_debug("PCI: abort_handler addr = %#lx, isr = %#x, " |
| 300 | "status = %#x\n", addr, isr, status); |
| 301 | |
| 302 | /* make sure the Master Abort bit is reset */ |
| 303 | *PCI_ISR = PCI_ISR_PFE; |
| 304 | status |= PCI_STATUS_REC_MASTER_ABORT; |
| 305 | local_write_config(PCI_STATUS, 2, status); |
| 306 | |
| 307 | /* |
| 308 | * If it was an imprecise abort, then we need to correct the |
| 309 | * return address to be _after_ the instruction. |
| 310 | */ |
| 311 | if (fsr & (1 << 10)) |
| 312 | regs->ARM_pc += 4; |
| 313 | |
| 314 | return 0; |
| 315 | } |
| 316 | |
| 317 | |
| 318 | /* |
| 319 | * Setup DMA mask to 64MB on PCI devices. Ignore all other devices. |
| 320 | */ |
| 321 | static int ixp4xx_pci_platform_notify(struct device *dev) |
| 322 | { |
| 323 | if(dev->bus == &pci_bus_type) { |
| 324 | *dev->dma_mask = SZ_64M - 1; |
| 325 | dev->coherent_dma_mask = SZ_64M - 1; |
| 326 | dmabounce_register_dev(dev, 2048, 4096); |
| 327 | } |
| 328 | return 0; |
| 329 | } |
| 330 | |
| 331 | static int ixp4xx_pci_platform_notify_remove(struct device *dev) |
| 332 | { |
| 333 | if(dev->bus == &pci_bus_type) { |
| 334 | dmabounce_unregister_dev(dev); |
| 335 | } |
| 336 | return 0; |
| 337 | } |
| 338 | |
| 339 | int dma_needs_bounce(struct device *dev, dma_addr_t dma_addr, size_t size) |
| 340 | { |
| 341 | return (dev->bus == &pci_bus_type ) && ((dma_addr + size) >= SZ_64M); |
| 342 | } |
| 343 | |
Rod Whitby | 313cbb5 | 2006-01-04 17:17:13 +0000 | [diff] [blame] | 344 | /* |
| 345 | * Only first 64MB of memory can be accessed via PCI. |
| 346 | * We use GFP_DMA to allocate safe buffers to do map/unmap. |
| 347 | * This is really ugly and we need a better way of specifying |
| 348 | * DMA-capable regions of memory. |
| 349 | */ |
| 350 | void __init ixp4xx_adjust_zones(int node, unsigned long *zone_size, |
| 351 | unsigned long *zhole_size) |
| 352 | { |
| 353 | unsigned int sz = SZ_64M >> PAGE_SHIFT; |
| 354 | |
| 355 | /* |
| 356 | * Only adjust if > 64M on current system |
| 357 | */ |
| 358 | if (node || (zone_size[0] <= sz)) |
| 359 | return; |
| 360 | |
| 361 | zone_size[1] = zone_size[0] - sz; |
| 362 | zone_size[0] = sz; |
| 363 | zhole_size[1] = zhole_size[0]; |
| 364 | zhole_size[0] = 0; |
| 365 | } |
| 366 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 367 | void __init ixp4xx_pci_preinit(void) |
| 368 | { |
| 369 | unsigned long processor_id; |
| 370 | |
| 371 | asm("mrc p15, 0, %0, cr0, cr0, 0;" : "=r"(processor_id) :); |
| 372 | |
| 373 | /* |
| 374 | * Determine which PCI read method to use. |
| 375 | * Rev 0 IXP425 requires workaround. |
| 376 | */ |
| 377 | if (!(processor_id & 0xf) && !cpu_is_ixp46x()) { |
| 378 | printk("PCI: IXP42x A0 silicon detected - " |
| 379 | "PCI Non-Prefetch Workaround Enabled\n"); |
| 380 | ixp4xx_pci_read = ixp4xx_pci_read_errata; |
| 381 | } else |
| 382 | ixp4xx_pci_read = ixp4xx_pci_read_no_errata; |
| 383 | |
| 384 | |
| 385 | /* hook in our fault handler for PCI errors */ |
| 386 | hook_fault_code(16+6, abort_handler, SIGBUS, "imprecise external abort"); |
| 387 | |
| 388 | pr_debug("setup PCI-AHB(inbound) and AHB-PCI(outbound) address mappings\n"); |
| 389 | |
| 390 | /* |
| 391 | * We use identity AHB->PCI address translation |
| 392 | * in the 0x48000000 to 0x4bffffff address space |
| 393 | */ |
| 394 | *PCI_PCIMEMBASE = 0x48494A4B; |
| 395 | |
| 396 | /* |
| 397 | * We also use identity PCI->AHB address translation |
| 398 | * in 4 16MB BARs that begin at the physical memory start |
| 399 | */ |
| 400 | *PCI_AHBMEMBASE = (PHYS_OFFSET & 0xFF000000) + |
| 401 | ((PHYS_OFFSET & 0xFF000000) >> 8) + |
| 402 | ((PHYS_OFFSET & 0xFF000000) >> 16) + |
| 403 | ((PHYS_OFFSET & 0xFF000000) >> 24) + |
| 404 | 0x00010203; |
| 405 | |
| 406 | if (*PCI_CSR & PCI_CSR_HOST) { |
| 407 | printk("PCI: IXP4xx is host\n"); |
| 408 | |
| 409 | pr_debug("setup BARs in controller\n"); |
| 410 | |
| 411 | /* |
| 412 | * We configure the PCI inbound memory windows to be |
| 413 | * 1:1 mapped to SDRAM |
| 414 | */ |
| 415 | local_write_config(PCI_BASE_ADDRESS_0, 4, PHYS_OFFSET + 0x00000000); |
| 416 | local_write_config(PCI_BASE_ADDRESS_1, 4, PHYS_OFFSET + 0x01000000); |
| 417 | local_write_config(PCI_BASE_ADDRESS_2, 4, PHYS_OFFSET + 0x02000000); |
| 418 | local_write_config(PCI_BASE_ADDRESS_3, 4, PHYS_OFFSET + 0x03000000); |
| 419 | |
| 420 | /* |
| 421 | * Enable CSR window at 0xff000000. |
| 422 | */ |
| 423 | local_write_config(PCI_BASE_ADDRESS_4, 4, 0xff000008); |
| 424 | |
| 425 | /* |
| 426 | * Enable the IO window to be way up high, at 0xfffffc00 |
| 427 | */ |
| 428 | local_write_config(PCI_BASE_ADDRESS_5, 4, 0xfffffc01); |
| 429 | } else { |
| 430 | printk("PCI: IXP4xx is target - No bus scan performed\n"); |
| 431 | } |
| 432 | |
| 433 | printk("PCI: IXP4xx Using %s access for memory space\n", |
| 434 | #ifndef CONFIG_IXP4XX_INDIRECT_PCI |
| 435 | "direct" |
| 436 | #else |
| 437 | "indirect" |
| 438 | #endif |
| 439 | ); |
| 440 | |
| 441 | pr_debug("clear error bits in ISR\n"); |
| 442 | *PCI_ISR = PCI_ISR_PSE | PCI_ISR_PFE | PCI_ISR_PPE | PCI_ISR_AHBE; |
| 443 | |
| 444 | /* |
| 445 | * Set Initialize Complete in PCI Control Register: allow IXP4XX to |
| 446 | * respond to PCI configuration cycles. Specify that the AHB bus is |
| 447 | * operating in big endian mode. Set up byte lane swapping between |
| 448 | * little-endian PCI and the big-endian AHB bus |
| 449 | */ |
| 450 | #ifdef __ARMEB__ |
| 451 | *PCI_CSR = PCI_CSR_IC | PCI_CSR_ABE | PCI_CSR_PDS | PCI_CSR_ADS; |
| 452 | #else |
Alessandro Zummo | 8461338 | 2005-11-06 14:34:12 +0000 | [diff] [blame] | 453 | *PCI_CSR = PCI_CSR_IC | PCI_CSR_ABE; |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 454 | #endif |
| 455 | |
| 456 | pr_debug("DONE\n"); |
| 457 | } |
| 458 | |
| 459 | int ixp4xx_setup(int nr, struct pci_sys_data *sys) |
| 460 | { |
| 461 | struct resource *res; |
| 462 | |
| 463 | if (nr >= 1) |
| 464 | return 0; |
| 465 | |
| 466 | res = kmalloc(sizeof(*res) * 2, GFP_KERNEL); |
| 467 | if (res == NULL) { |
| 468 | /* |
| 469 | * If we're out of memory this early, something is wrong, |
| 470 | * so we might as well catch it here. |
| 471 | */ |
| 472 | panic("PCI: unable to allocate resources?\n"); |
| 473 | } |
| 474 | memset(res, 0, sizeof(*res) * 2); |
| 475 | |
| 476 | local_write_config(PCI_COMMAND, 2, PCI_COMMAND_MASTER | PCI_COMMAND_MEMORY); |
| 477 | |
| 478 | res[0].name = "PCI I/O Space"; |
Deepak Saxena | 450008b | 2005-07-06 23:06:05 +0100 | [diff] [blame] | 479 | res[0].start = 0x00000000; |
| 480 | res[0].end = 0x0000ffff; |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 481 | res[0].flags = IORESOURCE_IO; |
| 482 | |
| 483 | res[1].name = "PCI Memory Space"; |
| 484 | res[1].start = 0x48000000; |
| 485 | #ifndef CONFIG_IXP4XX_INDIRECT_PCI |
| 486 | res[1].end = 0x4bffffff; |
| 487 | #else |
| 488 | res[1].end = 0x4fffffff; |
| 489 | #endif |
| 490 | res[1].flags = IORESOURCE_MEM; |
| 491 | |
| 492 | request_resource(&ioport_resource, &res[0]); |
| 493 | request_resource(&iomem_resource, &res[1]); |
| 494 | |
| 495 | sys->resource[0] = &res[0]; |
| 496 | sys->resource[1] = &res[1]; |
| 497 | sys->resource[2] = NULL; |
| 498 | |
| 499 | platform_notify = ixp4xx_pci_platform_notify; |
| 500 | platform_notify_remove = ixp4xx_pci_platform_notify_remove; |
| 501 | |
| 502 | return 1; |
| 503 | } |
| 504 | |
| 505 | struct pci_bus *ixp4xx_scan_bus(int nr, struct pci_sys_data *sys) |
| 506 | { |
| 507 | return pci_scan_bus(sys->busnr, &ixp4xx_ops, sys); |
| 508 | } |
| 509 | |
| 510 | /* |
| 511 | * We override these so we properly do dmabounce otherwise drivers |
| 512 | * are able to set the dma_mask to 0xffffffff and we can no longer |
| 513 | * trap bounces. :( |
| 514 | * |
| 515 | * We just return true on everyhing except for < 64MB in which case |
| 516 | * we will fail miseralby and die since we can't handle that case. |
| 517 | */ |
| 518 | int |
| 519 | pci_set_dma_mask(struct pci_dev *dev, u64 mask) |
| 520 | { |
| 521 | if (mask >= SZ_64M - 1 ) |
| 522 | return 0; |
| 523 | |
| 524 | return -EIO; |
| 525 | } |
| 526 | |
| 527 | int |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 528 | pci_set_consistent_dma_mask(struct pci_dev *dev, u64 mask) |
| 529 | { |
| 530 | if (mask >= SZ_64M - 1 ) |
| 531 | return 0; |
| 532 | |
| 533 | return -EIO; |
| 534 | } |
| 535 | |
| 536 | EXPORT_SYMBOL(pci_set_dma_mask); |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 537 | EXPORT_SYMBOL(pci_set_consistent_dma_mask); |
| 538 | EXPORT_SYMBOL(ixp4xx_pci_read); |
| 539 | EXPORT_SYMBOL(ixp4xx_pci_write); |
| 540 | |