blob: 3490022e9fdc7e923d265eb06e635f4dc32e5026 [file] [log] [blame]
Linus Torvalds1da177e2005-04-16 15:20:36 -07001/*
2 * linux/drivers/char/amba.c
3 *
4 * Driver for AMBA serial ports
5 *
6 * Based on drivers/char/serial.c, by Linus Torvalds, Theodore Ts'o.
7 *
8 * Copyright 1999 ARM Limited
9 * Copyright (C) 2000 Deep Blue Solutions Ltd.
10 *
11 * This program is free software; you can redistribute it and/or modify
12 * it under the terms of the GNU General Public License as published by
13 * the Free Software Foundation; either version 2 of the License, or
14 * (at your option) any later version.
15 *
16 * This program is distributed in the hope that it will be useful,
17 * but WITHOUT ANY WARRANTY; without even the implied warranty of
18 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
19 * GNU General Public License for more details.
20 *
21 * You should have received a copy of the GNU General Public License
22 * along with this program; if not, write to the Free Software
23 * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
24 *
25 * $Id: amba.c,v 1.41 2002/07/28 10:03:27 rmk Exp $
26 *
27 * This is a generic driver for ARM AMBA-type serial ports. They
28 * have a lot of 16550-like features, but are not register compatible.
29 * Note that although they do have CTS, DCD and DSR inputs, they do
30 * not have an RI input, nor do they have DTR or RTS outputs. If
31 * required, these have to be supplied via some other means (eg, GPIO)
32 * and hooked into this driver.
33 */
34#include <linux/config.h>
35
36#if defined(CONFIG_SERIAL_AMBA_PL010_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
37#define SUPPORT_SYSRQ
38#endif
39
40#include <linux/module.h>
41#include <linux/ioport.h>
42#include <linux/init.h>
43#include <linux/console.h>
44#include <linux/sysrq.h>
45#include <linux/device.h>
46#include <linux/tty.h>
47#include <linux/tty_flip.h>
48#include <linux/serial_core.h>
49#include <linux/serial.h>
Russell Kinga62c80e2006-01-07 13:52:45 +000050#include <linux/amba/bus.h>
51#include <linux/amba/serial.h>
Linus Torvalds1da177e2005-04-16 15:20:36 -070052
53#include <asm/io.h>
54#include <asm/irq.h>
Russell Kingc6b8fda2005-10-28 14:05:16 +010055#include <asm/hardware.h>
Linus Torvalds1da177e2005-04-16 15:20:36 -070056
57#define UART_NR 2
58
59#define SERIAL_AMBA_MAJOR 204
60#define SERIAL_AMBA_MINOR 16
61#define SERIAL_AMBA_NR UART_NR
62
63#define AMBA_ISR_PASS_LIMIT 256
64
65/*
66 * Access macros for the AMBA UARTs
67 */
68#define UART_GET_INT_STATUS(p) readb((p)->membase + UART010_IIR)
69#define UART_PUT_ICR(p, c) writel((c), (p)->membase + UART010_ICR)
70#define UART_GET_FR(p) readb((p)->membase + UART01x_FR)
71#define UART_GET_CHAR(p) readb((p)->membase + UART01x_DR)
72#define UART_PUT_CHAR(p, c) writel((c), (p)->membase + UART01x_DR)
73#define UART_GET_RSR(p) readb((p)->membase + UART01x_RSR)
74#define UART_GET_CR(p) readb((p)->membase + UART010_CR)
75#define UART_PUT_CR(p,c) writel((c), (p)->membase + UART010_CR)
76#define UART_GET_LCRL(p) readb((p)->membase + UART010_LCRL)
77#define UART_PUT_LCRL(p,c) writel((c), (p)->membase + UART010_LCRL)
78#define UART_GET_LCRM(p) readb((p)->membase + UART010_LCRM)
79#define UART_PUT_LCRM(p,c) writel((c), (p)->membase + UART010_LCRM)
80#define UART_GET_LCRH(p) readb((p)->membase + UART010_LCRH)
81#define UART_PUT_LCRH(p,c) writel((c), (p)->membase + UART010_LCRH)
82#define UART_RX_DATA(s) (((s) & UART01x_FR_RXFE) == 0)
83#define UART_TX_READY(s) (((s) & UART01x_FR_TXFF) == 0)
84#define UART_TX_EMPTY(p) ((UART_GET_FR(p) & UART01x_FR_TMSK) == 0)
85
86#define UART_DUMMY_RSR_RX /*256*/0
87#define UART_PORT_SIZE 64
88
89/*
90 * On the Integrator platform, the port RTS and DTR are provided by
91 * bits in the following SC_CTRLS register bits:
92 * RTS DTR
93 * UART0 7 6
94 * UART1 5 4
95 */
96#define SC_CTRLC (IO_ADDRESS(INTEGRATOR_SC_BASE) + INTEGRATOR_SC_CTRLC_OFFSET)
97#define SC_CTRLS (IO_ADDRESS(INTEGRATOR_SC_BASE) + INTEGRATOR_SC_CTRLS_OFFSET)
98
99/*
100 * We wrap our port structure around the generic uart_port.
101 */
102struct uart_amba_port {
103 struct uart_port port;
104 unsigned int dtr_mask;
105 unsigned int rts_mask;
106 unsigned int old_status;
107};
108
Russell Kingb129a8c2005-08-31 10:12:14 +0100109static void pl010_stop_tx(struct uart_port *port)
Linus Torvalds1da177e2005-04-16 15:20:36 -0700110{
111 unsigned int cr;
112
113 cr = UART_GET_CR(port);
114 cr &= ~UART010_CR_TIE;
115 UART_PUT_CR(port, cr);
116}
117
Russell Kingb129a8c2005-08-31 10:12:14 +0100118static void pl010_start_tx(struct uart_port *port)
Linus Torvalds1da177e2005-04-16 15:20:36 -0700119{
120 unsigned int cr;
121
122 cr = UART_GET_CR(port);
123 cr |= UART010_CR_TIE;
124 UART_PUT_CR(port, cr);
125}
126
127static void pl010_stop_rx(struct uart_port *port)
128{
129 unsigned int cr;
130
131 cr = UART_GET_CR(port);
132 cr &= ~(UART010_CR_RIE | UART010_CR_RTIE);
133 UART_PUT_CR(port, cr);
134}
135
136static void pl010_enable_ms(struct uart_port *port)
137{
138 unsigned int cr;
139
140 cr = UART_GET_CR(port);
141 cr |= UART010_CR_MSIE;
142 UART_PUT_CR(port, cr);
143}
144
145static void
146#ifdef SUPPORT_SYSRQ
147pl010_rx_chars(struct uart_port *port, struct pt_regs *regs)
148#else
149pl010_rx_chars(struct uart_port *port)
150#endif
151{
152 struct tty_struct *tty = port->info->tty;
153 unsigned int status, ch, flag, rsr, max_count = 256;
154
155 status = UART_GET_FR(port);
156 while (UART_RX_DATA(status) && max_count--) {
Linus Torvalds1da177e2005-04-16 15:20:36 -0700157 ch = UART_GET_CHAR(port);
158 flag = TTY_NORMAL;
159
160 port->icount.rx++;
161
162 /*
163 * Note that the error handling code is
164 * out of the main execution path
165 */
166 rsr = UART_GET_RSR(port) | UART_DUMMY_RSR_RX;
Russell King45849282005-04-26 15:29:44 +0100167 if (unlikely(rsr & UART01x_RSR_ANY)) {
Linus Torvalds1da177e2005-04-16 15:20:36 -0700168 if (rsr & UART01x_RSR_BE) {
169 rsr &= ~(UART01x_RSR_FE | UART01x_RSR_PE);
170 port->icount.brk++;
171 if (uart_handle_break(port))
172 goto ignore_char;
173 } else if (rsr & UART01x_RSR_PE)
174 port->icount.parity++;
175 else if (rsr & UART01x_RSR_FE)
176 port->icount.frame++;
177 if (rsr & UART01x_RSR_OE)
178 port->icount.overrun++;
179
180 rsr &= port->read_status_mask;
181
182 if (rsr & UART01x_RSR_BE)
183 flag = TTY_BREAK;
184 else if (rsr & UART01x_RSR_PE)
185 flag = TTY_PARITY;
186 else if (rsr & UART01x_RSR_FE)
187 flag = TTY_FRAME;
188 }
189
190 if (uart_handle_sysrq_char(port, ch, regs))
191 goto ignore_char;
192
Russell King05ab3012005-05-09 23:21:59 +0100193 uart_insert_char(port, rsr, UART01x_RSR_OE, ch, flag);
194
Linus Torvalds1da177e2005-04-16 15:20:36 -0700195 ignore_char:
196 status = UART_GET_FR(port);
197 }
198 tty_flip_buffer_push(tty);
199 return;
200}
201
202static void pl010_tx_chars(struct uart_port *port)
203{
204 struct circ_buf *xmit = &port->info->xmit;
205 int count;
206
207 if (port->x_char) {
208 UART_PUT_CHAR(port, port->x_char);
209 port->icount.tx++;
210 port->x_char = 0;
211 return;
212 }
213 if (uart_circ_empty(xmit) || uart_tx_stopped(port)) {
Russell Kingb129a8c2005-08-31 10:12:14 +0100214 pl010_stop_tx(port);
Linus Torvalds1da177e2005-04-16 15:20:36 -0700215 return;
216 }
217
218 count = port->fifosize >> 1;
219 do {
220 UART_PUT_CHAR(port, xmit->buf[xmit->tail]);
221 xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
222 port->icount.tx++;
223 if (uart_circ_empty(xmit))
224 break;
225 } while (--count > 0);
226
227 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
228 uart_write_wakeup(port);
229
230 if (uart_circ_empty(xmit))
Russell Kingb129a8c2005-08-31 10:12:14 +0100231 pl010_stop_tx(port);
Linus Torvalds1da177e2005-04-16 15:20:36 -0700232}
233
234static void pl010_modem_status(struct uart_port *port)
235{
236 struct uart_amba_port *uap = (struct uart_amba_port *)port;
237 unsigned int status, delta;
238
239 UART_PUT_ICR(&uap->port, 0);
240
241 status = UART_GET_FR(&uap->port) & UART01x_FR_MODEM_ANY;
242
243 delta = status ^ uap->old_status;
244 uap->old_status = status;
245
246 if (!delta)
247 return;
248
249 if (delta & UART01x_FR_DCD)
250 uart_handle_dcd_change(&uap->port, status & UART01x_FR_DCD);
251
252 if (delta & UART01x_FR_DSR)
253 uap->port.icount.dsr++;
254
255 if (delta & UART01x_FR_CTS)
256 uart_handle_cts_change(&uap->port, status & UART01x_FR_CTS);
257
258 wake_up_interruptible(&uap->port.info->delta_msr_wait);
259}
260
261static irqreturn_t pl010_int(int irq, void *dev_id, struct pt_regs *regs)
262{
263 struct uart_port *port = dev_id;
264 unsigned int status, pass_counter = AMBA_ISR_PASS_LIMIT;
265 int handled = 0;
266
267 spin_lock(&port->lock);
268
269 status = UART_GET_INT_STATUS(port);
270 if (status) {
271 do {
272 if (status & (UART010_IIR_RTIS | UART010_IIR_RIS))
273#ifdef SUPPORT_SYSRQ
274 pl010_rx_chars(port, regs);
275#else
276 pl010_rx_chars(port);
277#endif
278 if (status & UART010_IIR_MIS)
279 pl010_modem_status(port);
280 if (status & UART010_IIR_TIS)
281 pl010_tx_chars(port);
282
283 if (pass_counter-- == 0)
284 break;
285
286 status = UART_GET_INT_STATUS(port);
287 } while (status & (UART010_IIR_RTIS | UART010_IIR_RIS |
288 UART010_IIR_TIS));
289 handled = 1;
290 }
291
292 spin_unlock(&port->lock);
293
294 return IRQ_RETVAL(handled);
295}
296
297static unsigned int pl010_tx_empty(struct uart_port *port)
298{
299 return UART_GET_FR(port) & UART01x_FR_BUSY ? 0 : TIOCSER_TEMT;
300}
301
302static unsigned int pl010_get_mctrl(struct uart_port *port)
303{
304 unsigned int result = 0;
305 unsigned int status;
306
307 status = UART_GET_FR(port);
308 if (status & UART01x_FR_DCD)
309 result |= TIOCM_CAR;
310 if (status & UART01x_FR_DSR)
311 result |= TIOCM_DSR;
312 if (status & UART01x_FR_CTS)
313 result |= TIOCM_CTS;
314
315 return result;
316}
317
318static void pl010_set_mctrl(struct uart_port *port, unsigned int mctrl)
319{
320 struct uart_amba_port *uap = (struct uart_amba_port *)port;
321 unsigned int ctrls = 0, ctrlc = 0;
322
323 if (mctrl & TIOCM_RTS)
324 ctrlc |= uap->rts_mask;
325 else
326 ctrls |= uap->rts_mask;
327
328 if (mctrl & TIOCM_DTR)
329 ctrlc |= uap->dtr_mask;
330 else
331 ctrls |= uap->dtr_mask;
332
333 __raw_writel(ctrls, SC_CTRLS);
334 __raw_writel(ctrlc, SC_CTRLC);
335}
336
337static void pl010_break_ctl(struct uart_port *port, int break_state)
338{
339 unsigned long flags;
340 unsigned int lcr_h;
341
342 spin_lock_irqsave(&port->lock, flags);
343 lcr_h = UART_GET_LCRH(port);
344 if (break_state == -1)
345 lcr_h |= UART01x_LCRH_BRK;
346 else
347 lcr_h &= ~UART01x_LCRH_BRK;
348 UART_PUT_LCRH(port, lcr_h);
349 spin_unlock_irqrestore(&port->lock, flags);
350}
351
352static int pl010_startup(struct uart_port *port)
353{
354 struct uart_amba_port *uap = (struct uart_amba_port *)port;
355 int retval;
356
357 /*
358 * Allocate the IRQ
359 */
360 retval = request_irq(port->irq, pl010_int, 0, "uart-pl010", port);
361 if (retval)
362 return retval;
363
364 /*
365 * initialise the old status of the modem signals
366 */
367 uap->old_status = UART_GET_FR(port) & UART01x_FR_MODEM_ANY;
368
369 /*
370 * Finally, enable interrupts
371 */
372 UART_PUT_CR(port, UART01x_CR_UARTEN | UART010_CR_RIE |
373 UART010_CR_RTIE);
374
375 return 0;
376}
377
378static void pl010_shutdown(struct uart_port *port)
379{
380 /*
381 * Free the interrupt
382 */
383 free_irq(port->irq, port);
384
385 /*
386 * disable all interrupts, disable the port
387 */
388 UART_PUT_CR(port, 0);
389
390 /* disable break condition and fifos */
391 UART_PUT_LCRH(port, UART_GET_LCRH(port) &
392 ~(UART01x_LCRH_BRK | UART01x_LCRH_FEN));
393}
394
395static void
396pl010_set_termios(struct uart_port *port, struct termios *termios,
397 struct termios *old)
398{
399 unsigned int lcr_h, old_cr;
400 unsigned long flags;
401 unsigned int baud, quot;
402
403 /*
404 * Ask the core to calculate the divisor for us.
405 */
406 baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/16);
407 quot = uart_get_divisor(port, baud);
408
409 switch (termios->c_cflag & CSIZE) {
410 case CS5:
411 lcr_h = UART01x_LCRH_WLEN_5;
412 break;
413 case CS6:
414 lcr_h = UART01x_LCRH_WLEN_6;
415 break;
416 case CS7:
417 lcr_h = UART01x_LCRH_WLEN_7;
418 break;
419 default: // CS8
420 lcr_h = UART01x_LCRH_WLEN_8;
421 break;
422 }
423 if (termios->c_cflag & CSTOPB)
424 lcr_h |= UART01x_LCRH_STP2;
425 if (termios->c_cflag & PARENB) {
426 lcr_h |= UART01x_LCRH_PEN;
427 if (!(termios->c_cflag & PARODD))
428 lcr_h |= UART01x_LCRH_EPS;
429 }
430 if (port->fifosize > 1)
431 lcr_h |= UART01x_LCRH_FEN;
432
433 spin_lock_irqsave(&port->lock, flags);
434
435 /*
436 * Update the per-port timeout.
437 */
438 uart_update_timeout(port, termios->c_cflag, baud);
439
440 port->read_status_mask = UART01x_RSR_OE;
441 if (termios->c_iflag & INPCK)
442 port->read_status_mask |= UART01x_RSR_FE | UART01x_RSR_PE;
443 if (termios->c_iflag & (BRKINT | PARMRK))
444 port->read_status_mask |= UART01x_RSR_BE;
445
446 /*
447 * Characters to ignore
448 */
449 port->ignore_status_mask = 0;
450 if (termios->c_iflag & IGNPAR)
451 port->ignore_status_mask |= UART01x_RSR_FE | UART01x_RSR_PE;
452 if (termios->c_iflag & IGNBRK) {
453 port->ignore_status_mask |= UART01x_RSR_BE;
454 /*
455 * If we're ignoring parity and break indicators,
456 * ignore overruns too (for real raw support).
457 */
458 if (termios->c_iflag & IGNPAR)
459 port->ignore_status_mask |= UART01x_RSR_OE;
460 }
461
462 /*
463 * Ignore all characters if CREAD is not set.
464 */
465 if ((termios->c_cflag & CREAD) == 0)
466 port->ignore_status_mask |= UART_DUMMY_RSR_RX;
467
468 /* first, disable everything */
469 old_cr = UART_GET_CR(port) & ~UART010_CR_MSIE;
470
471 if (UART_ENABLE_MS(port, termios->c_cflag))
472 old_cr |= UART010_CR_MSIE;
473
474 UART_PUT_CR(port, 0);
475
476 /* Set baud rate */
477 quot -= 1;
478 UART_PUT_LCRM(port, ((quot & 0xf00) >> 8));
479 UART_PUT_LCRL(port, (quot & 0xff));
480
481 /*
482 * ----------v----------v----------v----------v-----
483 * NOTE: MUST BE WRITTEN AFTER UARTLCR_M & UARTLCR_L
484 * ----------^----------^----------^----------^-----
485 */
486 UART_PUT_LCRH(port, lcr_h);
487 UART_PUT_CR(port, old_cr);
488
489 spin_unlock_irqrestore(&port->lock, flags);
490}
491
492static const char *pl010_type(struct uart_port *port)
493{
494 return port->type == PORT_AMBA ? "AMBA" : NULL;
495}
496
497/*
498 * Release the memory region(s) being used by 'port'
499 */
500static void pl010_release_port(struct uart_port *port)
501{
502 release_mem_region(port->mapbase, UART_PORT_SIZE);
503}
504
505/*
506 * Request the memory region(s) being used by 'port'
507 */
508static int pl010_request_port(struct uart_port *port)
509{
510 return request_mem_region(port->mapbase, UART_PORT_SIZE, "uart-pl010")
511 != NULL ? 0 : -EBUSY;
512}
513
514/*
515 * Configure/autoconfigure the port.
516 */
517static void pl010_config_port(struct uart_port *port, int flags)
518{
519 if (flags & UART_CONFIG_TYPE) {
520 port->type = PORT_AMBA;
521 pl010_request_port(port);
522 }
523}
524
525/*
526 * verify the new serial_struct (for TIOCSSERIAL).
527 */
528static int pl010_verify_port(struct uart_port *port, struct serial_struct *ser)
529{
530 int ret = 0;
531 if (ser->type != PORT_UNKNOWN && ser->type != PORT_AMBA)
532 ret = -EINVAL;
533 if (ser->irq < 0 || ser->irq >= NR_IRQS)
534 ret = -EINVAL;
535 if (ser->baud_base < 9600)
536 ret = -EINVAL;
537 return ret;
538}
539
540static struct uart_ops amba_pl010_pops = {
541 .tx_empty = pl010_tx_empty,
542 .set_mctrl = pl010_set_mctrl,
543 .get_mctrl = pl010_get_mctrl,
544 .stop_tx = pl010_stop_tx,
545 .start_tx = pl010_start_tx,
546 .stop_rx = pl010_stop_rx,
547 .enable_ms = pl010_enable_ms,
548 .break_ctl = pl010_break_ctl,
549 .startup = pl010_startup,
550 .shutdown = pl010_shutdown,
551 .set_termios = pl010_set_termios,
552 .type = pl010_type,
553 .release_port = pl010_release_port,
554 .request_port = pl010_request_port,
555 .config_port = pl010_config_port,
556 .verify_port = pl010_verify_port,
557};
558
559static struct uart_amba_port amba_ports[UART_NR] = {
560 {
561 .port = {
562 .membase = (void *)IO_ADDRESS(INTEGRATOR_UART0_BASE),
563 .mapbase = INTEGRATOR_UART0_BASE,
564 .iotype = SERIAL_IO_MEM,
565 .irq = IRQ_UARTINT0,
566 .uartclk = 14745600,
567 .fifosize = 16,
568 .ops = &amba_pl010_pops,
569 .flags = ASYNC_BOOT_AUTOCONF,
570 .line = 0,
571 },
572 .dtr_mask = 1 << 5,
573 .rts_mask = 1 << 4,
574 },
575 {
576 .port = {
577 .membase = (void *)IO_ADDRESS(INTEGRATOR_UART1_BASE),
578 .mapbase = INTEGRATOR_UART1_BASE,
579 .iotype = SERIAL_IO_MEM,
580 .irq = IRQ_UARTINT1,
581 .uartclk = 14745600,
582 .fifosize = 16,
583 .ops = &amba_pl010_pops,
584 .flags = ASYNC_BOOT_AUTOCONF,
585 .line = 1,
586 },
587 .dtr_mask = 1 << 7,
588 .rts_mask = 1 << 6,
589 }
590};
591
592#ifdef CONFIG_SERIAL_AMBA_PL010_CONSOLE
593
594static void
595pl010_console_write(struct console *co, const char *s, unsigned int count)
596{
597 struct uart_port *port = &amba_ports[co->index].port;
598 unsigned int status, old_cr;
599 int i;
600
601 /*
602 * First save the CR then disable the interrupts
603 */
604 old_cr = UART_GET_CR(port);
605 UART_PUT_CR(port, UART01x_CR_UARTEN);
606
607 /*
608 * Now, do each character
609 */
610 for (i = 0; i < count; i++) {
611 do {
612 status = UART_GET_FR(port);
613 } while (!UART_TX_READY(status));
614 UART_PUT_CHAR(port, s[i]);
615 if (s[i] == '\n') {
616 do {
617 status = UART_GET_FR(port);
618 } while (!UART_TX_READY(status));
619 UART_PUT_CHAR(port, '\r');
620 }
621 }
622
623 /*
624 * Finally, wait for transmitter to become empty
625 * and restore the TCR
626 */
627 do {
628 status = UART_GET_FR(port);
629 } while (status & UART01x_FR_BUSY);
630 UART_PUT_CR(port, old_cr);
631}
632
633static void __init
634pl010_console_get_options(struct uart_port *port, int *baud,
635 int *parity, int *bits)
636{
637 if (UART_GET_CR(port) & UART01x_CR_UARTEN) {
638 unsigned int lcr_h, quot;
639 lcr_h = UART_GET_LCRH(port);
640
641 *parity = 'n';
642 if (lcr_h & UART01x_LCRH_PEN) {
643 if (lcr_h & UART01x_LCRH_EPS)
644 *parity = 'e';
645 else
646 *parity = 'o';
647 }
648
649 if ((lcr_h & 0x60) == UART01x_LCRH_WLEN_7)
650 *bits = 7;
651 else
652 *bits = 8;
653
654 quot = UART_GET_LCRL(port) | UART_GET_LCRM(port) << 8;
655 *baud = port->uartclk / (16 * (quot + 1));
656 }
657}
658
659static int __init pl010_console_setup(struct console *co, char *options)
660{
661 struct uart_port *port;
662 int baud = 38400;
663 int bits = 8;
664 int parity = 'n';
665 int flow = 'n';
666
667 /*
668 * Check whether an invalid uart number has been specified, and
669 * if so, search for the first available port that does have
670 * console support.
671 */
672 if (co->index >= UART_NR)
673 co->index = 0;
674 port = &amba_ports[co->index].port;
675
676 if (options)
677 uart_parse_options(options, &baud, &parity, &bits, &flow);
678 else
679 pl010_console_get_options(port, &baud, &parity, &bits);
680
681 return uart_set_options(port, co, baud, parity, bits, flow);
682}
683
Vincent Sanders2d934862005-09-14 22:36:03 +0100684static struct uart_driver amba_reg;
Linus Torvalds1da177e2005-04-16 15:20:36 -0700685static struct console amba_console = {
686 .name = "ttyAM",
687 .write = pl010_console_write,
688 .device = uart_console_device,
689 .setup = pl010_console_setup,
690 .flags = CON_PRINTBUFFER,
691 .index = -1,
692 .data = &amba_reg,
693};
694
695static int __init amba_console_init(void)
696{
697 /*
698 * All port initializations are done statically
699 */
700 register_console(&amba_console);
701 return 0;
702}
703console_initcall(amba_console_init);
704
705static int __init amba_late_console_init(void)
706{
707 if (!(amba_console.flags & CON_ENABLED))
708 register_console(&amba_console);
709 return 0;
710}
711late_initcall(amba_late_console_init);
712
713#define AMBA_CONSOLE &amba_console
714#else
715#define AMBA_CONSOLE NULL
716#endif
717
718static struct uart_driver amba_reg = {
719 .owner = THIS_MODULE,
720 .driver_name = "ttyAM",
721 .dev_name = "ttyAM",
722 .major = SERIAL_AMBA_MAJOR,
723 .minor = SERIAL_AMBA_MINOR,
724 .nr = UART_NR,
725 .cons = AMBA_CONSOLE,
726};
727
728static int pl010_probe(struct amba_device *dev, void *id)
729{
730 int i;
731
732 for (i = 0; i < UART_NR; i++) {
733 if (amba_ports[i].port.mapbase != dev->res.start)
734 continue;
735
736 amba_ports[i].port.dev = &dev->dev;
737 uart_add_one_port(&amba_reg, &amba_ports[i].port);
738 amba_set_drvdata(dev, &amba_ports[i]);
739 break;
740 }
741
742 return 0;
743}
744
745static int pl010_remove(struct amba_device *dev)
746{
747 struct uart_amba_port *uap = amba_get_drvdata(dev);
748
749 if (uap)
750 uart_remove_one_port(&amba_reg, &uap->port);
751
752 amba_set_drvdata(dev, NULL);
753
754 return 0;
755}
756
Pavel Machek0370aff2005-04-16 15:25:35 -0700757static int pl010_suspend(struct amba_device *dev, pm_message_t state)
Linus Torvalds1da177e2005-04-16 15:20:36 -0700758{
759 struct uart_amba_port *uap = amba_get_drvdata(dev);
760
761 if (uap)
762 uart_suspend_port(&amba_reg, &uap->port);
763
764 return 0;
765}
766
767static int pl010_resume(struct amba_device *dev)
768{
769 struct uart_amba_port *uap = amba_get_drvdata(dev);
770
771 if (uap)
772 uart_resume_port(&amba_reg, &uap->port);
773
774 return 0;
775}
776
777static struct amba_id pl010_ids[] __initdata = {
778 {
779 .id = 0x00041010,
780 .mask = 0x000fffff,
781 },
782 { 0, 0 },
783};
784
785static struct amba_driver pl010_driver = {
786 .drv = {
787 .name = "uart-pl010",
788 },
789 .id_table = pl010_ids,
790 .probe = pl010_probe,
791 .remove = pl010_remove,
792 .suspend = pl010_suspend,
793 .resume = pl010_resume,
794};
795
796static int __init pl010_init(void)
797{
798 int ret;
799
800 printk(KERN_INFO "Serial: AMBA driver $Revision: 1.41 $\n");
801
802 ret = uart_register_driver(&amba_reg);
803 if (ret == 0) {
804 ret = amba_driver_register(&pl010_driver);
805 if (ret)
806 uart_unregister_driver(&amba_reg);
807 }
808 return ret;
809}
810
811static void __exit pl010_exit(void)
812{
813 amba_driver_unregister(&pl010_driver);
814 uart_unregister_driver(&amba_reg);
815}
816
817module_init(pl010_init);
818module_exit(pl010_exit);
819
820MODULE_AUTHOR("ARM Ltd/Deep Blue Solutions Ltd");
821MODULE_DESCRIPTION("ARM AMBA serial port driver $Revision: 1.41 $");
822MODULE_LICENSE("GPL");