Mike Sinkovsky | 9899b81 | 2012-04-04 19:33:53 +0000 | [diff] [blame] | 1 | # |
| 2 | # WIZnet devices configuration |
| 3 | # |
| 4 | |
| 5 | config NET_VENDOR_WIZNET |
| 6 | bool "WIZnet devices" |
frank.blaschka@de.ibm.com | 9fafbd4 | 2012-07-24 22:34:27 +0000 | [diff] [blame] | 7 | depends on HAS_IOMEM |
Mike Sinkovsky | 9899b81 | 2012-04-04 19:33:53 +0000 | [diff] [blame] | 8 | default y |
| 9 | ---help--- |
| 10 | If you have a network (Ethernet) card belonging to this class, say Y |
| 11 | and read the Ethernet-HOWTO, available from |
| 12 | <http://www.tldp.org/docs.html#howto>. |
| 13 | |
| 14 | Note that the answer to this question doesn't directly affect the |
| 15 | kernel: saying N will just cause the configurator to skip all |
| 16 | the questions about WIZnet devices. If you say Y, you will be asked |
| 17 | for your specific card in the following questions. |
| 18 | |
| 19 | if NET_VENDOR_WIZNET |
| 20 | |
Mike Sinkovsky | 8b1467a | 2012-04-04 19:33:54 +0000 | [diff] [blame] | 21 | config WIZNET_W5100 |
| 22 | tristate "WIZnet W5100 Ethernet support" |
David S. Miller | 32ed53b | 2012-04-10 09:25:46 -0400 | [diff] [blame] | 23 | depends on HAS_IOMEM |
Mike Sinkovsky | 8b1467a | 2012-04-04 19:33:54 +0000 | [diff] [blame] | 24 | ---help--- |
| 25 | Support for WIZnet W5100 chips. |
| 26 | |
| 27 | W5100 is a single chip with integrated 10/100 Ethernet MAC, |
| 28 | PHY and hardware TCP/IP stack, but this driver is limited to |
| 29 | the MAC and PHY functions only, onchip TCP/IP is unused. |
| 30 | |
| 31 | To compile this driver as a module, choose M here: the module |
| 32 | will be called w5100. |
| 33 | |
Mike Sinkovsky | 9899b81 | 2012-04-04 19:33:53 +0000 | [diff] [blame] | 34 | config WIZNET_W5300 |
| 35 | tristate "WIZnet W5300 Ethernet support" |
David S. Miller | 32ed53b | 2012-04-10 09:25:46 -0400 | [diff] [blame] | 36 | depends on HAS_IOMEM |
Mike Sinkovsky | 9899b81 | 2012-04-04 19:33:53 +0000 | [diff] [blame] | 37 | ---help--- |
| 38 | Support for WIZnet W5300 chips. |
| 39 | |
| 40 | W5300 is a single chip with integrated 10/100 Ethernet MAC, |
| 41 | PHY and hardware TCP/IP stack, but this driver is limited to |
| 42 | the MAC and PHY functions only, onchip TCP/IP is unused. |
| 43 | |
| 44 | To compile this driver as a module, choose M here: the module |
| 45 | will be called w5300. |
| 46 | |
| 47 | choice |
| 48 | prompt "WIZnet interface mode" |
David S. Miller | 32ed53b | 2012-04-10 09:25:46 -0400 | [diff] [blame] | 49 | depends on WIZNET_W5100 || WIZNET_W5300 |
Mike Sinkovsky | 9899b81 | 2012-04-04 19:33:53 +0000 | [diff] [blame] | 50 | default WIZNET_BUS_ANY |
| 51 | |
| 52 | config WIZNET_BUS_DIRECT |
| 53 | bool "Direct address bus mode" |
| 54 | ---help--- |
| 55 | In direct address mode host system can directly access all registers |
| 56 | after mapping to Memory-Mapped I/O space. |
| 57 | |
| 58 | config WIZNET_BUS_INDIRECT |
| 59 | bool "Indirect address bus mode" |
| 60 | ---help--- |
| 61 | In indirect address mode host system indirectly accesses registers |
| 62 | using Indirect Mode Address Register and Indirect Mode Data Register, |
| 63 | which are directly mapped to Memory-Mapped I/O space. |
| 64 | |
| 65 | config WIZNET_BUS_ANY |
| 66 | bool "Select interface mode in runtime" |
| 67 | ---help--- |
| 68 | If interface mode is unknown in compile time, it can be selected |
| 69 | in runtime from board/platform resources configuration. |
| 70 | |
| 71 | Performance may decrease compared to explicitly selected bus mode. |
| 72 | endchoice |
| 73 | |
Mike Sinkovsky | 9899b81 | 2012-04-04 19:33:53 +0000 | [diff] [blame] | 74 | endif # NET_VENDOR_WIZNET |