blob: 7e6aa5b20c372f75a59f7dfd8c9c935f7f3cff75 [file] [log] [blame]
Linus Torvalds1da177e2005-04-16 15:20:36 -07001(C) 1997-1998 Caldera, Inc.
2(C) 1998 James Banks
3(C) 1999-2001 Torben Mathiasen <tmm@image.dk, torben.mathiasen@compaq.com>
4
5For driver information/updates visit http://opensource.compaq.com
6
7
8TLAN driver for Linux, version 1.14a
9README
10
11
12I. Supported Devices.
13
14 Only PCI devices will work with this driver.
15
16 Supported:
17 Vendor ID Device ID Name
18 0e11 ae32 Compaq Netelligent 10/100 TX PCI UTP
19 0e11 ae34 Compaq Netelligent 10 T PCI UTP
20 0e11 ae35 Compaq Integrated NetFlex 3/P
21 0e11 ae40 Compaq Netelligent Dual 10/100 TX PCI UTP
22 0e11 ae43 Compaq Netelligent Integrated 10/100 TX UTP
23 0e11 b011 Compaq Netelligent 10/100 TX Embedded UTP
24 0e11 b012 Compaq Netelligent 10 T/2 PCI UTP/Coax
25 0e11 b030 Compaq Netelligent 10/100 TX UTP
26 0e11 f130 Compaq NetFlex 3/P
27 0e11 f150 Compaq NetFlex 3/P
28 108d 0012 Olicom OC-2325
29 108d 0013 Olicom OC-2183
30 108d 0014 Olicom OC-2326
31
32
33 Caveats:
34
35 I am not sure if 100BaseTX daughterboards (for those cards which
36 support such things) will work. I haven't had any solid evidence
37 either way.
38
39 However, if a card supports 100BaseTx without requiring an add
40 on daughterboard, it should work with 100BaseTx.
41
42 The "Netelligent 10 T/2 PCI UTP/Coax" (b012) device is untested,
43 but I do not expect any problems.
44
45
46II. Driver Options
47 1. You can append debug=x to the end of the insmod line to get
48 debug messages, where x is a bit field where the bits mean
49 the following:
50
51 0x01 Turn on general debugging messages.
52 0x02 Turn on receive debugging messages.
53 0x04 Turn on transmit debugging messages.
54 0x08 Turn on list debugging messages.
55
56 2. You can append aui=1 to the end of the insmod line to cause
57 the adapter to use the AUI interface instead of the 10 Base T
58 interface. This is also what to do if you want to use the BNC
59 connector on a TLAN based device. (Setting this option on a
60 device that does not have an AUI/BNC connector will probably
61 cause it to not function correctly.)
62
63 3. You can set duplex=1 to force half duplex, and duplex=2 to
64 force full duplex.
65
66 4. You can set speed=10 to force 10Mbs operation, and speed=100
67 to force 100Mbs operation. (I'm not sure what will happen
68 if a card which only supports 10Mbs is forced into 100Mbs
69 mode.)
70
71 5. You have to use speed=X duplex=Y together now. If you just
72 do "insmod tlan.o speed=100" the driver will do Auto-Neg.
73 To force a 10Mbps Half-Duplex link do "insmod tlan.o speed=10
74 duplex=1".
75
76 6. If the driver is built into the kernel, you can use the 3rd
77 and 4th parameters to set aui and debug respectively. For
78 example:
79
80 ether=0,0,0x1,0x7,eth0
81
82 This sets aui to 0x1 and debug to 0x7, assuming eth0 is a
83 supported TLAN device.
84
85 The bits in the third byte are assigned as follows:
86
87 0x01 = aui
88 0x02 = use half duplex
89 0x04 = use full duplex
90 0x08 = use 10BaseT
91 0x10 = use 100BaseTx
92
93 You also need to set both speed and duplex settings when forcing
94 speeds with kernel-parameters.
95 ether=0,0,0x12,0,eth0 will force link to 100Mbps Half-Duplex.
96
97 7. If you have more than one tlan adapter in your system, you can
98 use the above options on a per adapter basis. To force a 100Mbit/HD
99 link with your eth1 adapter use:
100
101 insmod tlan speed=0,100 duplex=0,1
102
103 Now eth0 will use auto-neg and eth1 will be forced to 100Mbit/HD.
104 Note that the tlan driver supports a maximum of 8 adapters.
105
106
107III. Things to try if you have problems.
108 1. Make sure your card's PCI id is among those listed in
109 section I, above.
110 2. Make sure routing is correct.
111 3. Try forcing different speed/duplex settings
112
113
114There is also a tlan mailing list which you can join by sending "subscribe tlan"
115in the body of an email to majordomo@vuser.vu.union.edu.
116There is also a tlan website at http://opensource.compaq.com
117