blob: ca73637524012adbdeb4a7cad69558b7dd045430 [file] [log] [blame]
Linus Torvalds1da177e2005-04-16 15:20:36 -07001#include <linux/types.h>
2#include <linux/mm.h>
3#include <linux/blkdev.h>
Linus Torvalds1da177e2005-04-16 15:20:36 -07004#include <linux/init.h>
5#include <linux/interrupt.h>
6
7#include <asm/setup.h>
8#include <asm/page.h>
9#include <asm/pgtable.h>
10#include <asm/amigaints.h>
11#include <asm/amigahw.h>
12#include <linux/zorro.h>
13#include <asm/irq.h>
14#include <linux/spinlock.h>
15
16#include "scsi.h"
17#include <scsi/scsi_host.h>
18#include "wd33c93.h"
19#include "gvp11.h"
20
21#include<linux/stat.h>
22
23#define DMA(ptr) ((gvp11_scsiregs *)((ptr)->base))
24#define HDATA(ptr) ((struct WD33C93_hostdata *)((ptr)->hostdata))
25
David Howells7d12e782006-10-05 14:55:46 +010026static irqreturn_t gvp11_intr (int irq, void *_instance)
Linus Torvalds1da177e2005-04-16 15:20:36 -070027{
28 unsigned long flags;
29 unsigned int status;
30 struct Scsi_Host *instance = (struct Scsi_Host *)_instance;
31
32 status = DMA(instance)->CNTR;
33 if (!(status & GVP11_DMAC_INT_PENDING))
34 return IRQ_NONE;
35
36 spin_lock_irqsave(instance->host_lock, flags);
37 wd33c93_intr(instance);
38 spin_unlock_irqrestore(instance->host_lock, flags);
39 return IRQ_HANDLED;
40}
41
42static int gvp11_xfer_mask = 0;
43
44void gvp11_setup (char *str, int *ints)
45{
46 gvp11_xfer_mask = ints[1];
47}
48
Henrik Kretzschmar65396412006-09-12 23:49:33 +020049static int dma_setup(struct scsi_cmnd *cmd, int dir_in)
Linus Torvalds1da177e2005-04-16 15:20:36 -070050{
51 unsigned short cntr = GVP11_DMAC_INT_ENABLE;
52 unsigned long addr = virt_to_bus(cmd->SCp.ptr);
53 int bank_mask;
54 static int scsi_alloc_out_of_range = 0;
55
56 /* use bounce buffer if the physical address is bad */
Adrian Bunk7b892802008-02-06 01:36:29 -080057 if (addr & HDATA(cmd->device->host)->dma_xfer_mask)
Linus Torvalds1da177e2005-04-16 15:20:36 -070058 {
59 HDATA(cmd->device->host)->dma_bounce_len = (cmd->SCp.this_residual + 511)
60 & ~0x1ff;
61
62 if( !scsi_alloc_out_of_range ) {
63 HDATA(cmd->device->host)->dma_bounce_buffer =
64 kmalloc (HDATA(cmd->device->host)->dma_bounce_len, GFP_KERNEL);
65 HDATA(cmd->device->host)->dma_buffer_pool = BUF_SCSI_ALLOCED;
66 }
67
68 if (scsi_alloc_out_of_range ||
69 !HDATA(cmd->device->host)->dma_bounce_buffer) {
70 HDATA(cmd->device->host)->dma_bounce_buffer =
71 amiga_chip_alloc(HDATA(cmd->device->host)->dma_bounce_len,
72 "GVP II SCSI Bounce Buffer");
73
74 if(!HDATA(cmd->device->host)->dma_bounce_buffer)
75 {
76 HDATA(cmd->device->host)->dma_bounce_len = 0;
77 return 1;
78 }
79
80 HDATA(cmd->device->host)->dma_buffer_pool = BUF_CHIP_ALLOCED;
81 }
82
83 /* check if the address of the bounce buffer is OK */
84 addr = virt_to_bus(HDATA(cmd->device->host)->dma_bounce_buffer);
85
86 if (addr & HDATA(cmd->device->host)->dma_xfer_mask) {
87 /* fall back to Chip RAM if address out of range */
88 if( HDATA(cmd->device->host)->dma_buffer_pool == BUF_SCSI_ALLOCED) {
89 kfree (HDATA(cmd->device->host)->dma_bounce_buffer);
90 scsi_alloc_out_of_range = 1;
91 } else {
92 amiga_chip_free (HDATA(cmd->device->host)->dma_bounce_buffer);
93 }
94
95 HDATA(cmd->device->host)->dma_bounce_buffer =
96 amiga_chip_alloc(HDATA(cmd->device->host)->dma_bounce_len,
97 "GVP II SCSI Bounce Buffer");
98
99 if(!HDATA(cmd->device->host)->dma_bounce_buffer)
100 {
101 HDATA(cmd->device->host)->dma_bounce_len = 0;
102 return 1;
103 }
104
105 addr = virt_to_bus(HDATA(cmd->device->host)->dma_bounce_buffer);
106 HDATA(cmd->device->host)->dma_buffer_pool = BUF_CHIP_ALLOCED;
107 }
108
109 if (!dir_in) {
110 /* copy to bounce buffer for a write */
111 memcpy (HDATA(cmd->device->host)->dma_bounce_buffer,
112 cmd->SCp.ptr, cmd->SCp.this_residual);
113 }
114 }
115
116 /* setup dma direction */
117 if (!dir_in)
118 cntr |= GVP11_DMAC_DIR_WRITE;
119
120 HDATA(cmd->device->host)->dma_dir = dir_in;
121 DMA(cmd->device->host)->CNTR = cntr;
122
123 /* setup DMA *physical* address */
124 DMA(cmd->device->host)->ACR = addr;
125
126 if (dir_in)
127 /* invalidate any cache */
128 cache_clear (addr, cmd->SCp.this_residual);
129 else
130 /* push any dirty cache */
131 cache_push (addr, cmd->SCp.this_residual);
132
133 if ((bank_mask = (~HDATA(cmd->device->host)->dma_xfer_mask >> 18) & 0x01c0))
134 DMA(cmd->device->host)->BANK = bank_mask & (addr >> 18);
135
136 /* start DMA */
137 DMA(cmd->device->host)->ST_DMA = 1;
138
139 /* return success */
140 return 0;
141}
142
Henrik Kretzschmar65396412006-09-12 23:49:33 +0200143static void dma_stop(struct Scsi_Host *instance, struct scsi_cmnd *SCpnt,
144 int status)
Linus Torvalds1da177e2005-04-16 15:20:36 -0700145{
146 /* stop DMA */
147 DMA(instance)->SP_DMA = 1;
148 /* remove write bit from CONTROL bits */
149 DMA(instance)->CNTR = GVP11_DMAC_INT_ENABLE;
150
151 /* copy from a bounce buffer, if necessary */
152 if (status && HDATA(instance)->dma_bounce_buffer) {
153 if (HDATA(instance)->dma_dir && SCpnt)
154 memcpy (SCpnt->SCp.ptr,
155 HDATA(instance)->dma_bounce_buffer,
156 SCpnt->SCp.this_residual);
157
158 if (HDATA(instance)->dma_buffer_pool == BUF_SCSI_ALLOCED)
159 kfree (HDATA(instance)->dma_bounce_buffer);
160 else
161 amiga_chip_free(HDATA(instance)->dma_bounce_buffer);
162
163 HDATA(instance)->dma_bounce_buffer = NULL;
164 HDATA(instance)->dma_bounce_len = 0;
165 }
166}
167
168#define CHECK_WD33C93
169
Christoph Hellwigd0be4a7d2005-10-31 18:31:40 +0100170int __init gvp11_detect(struct scsi_host_template *tpnt)
Linus Torvalds1da177e2005-04-16 15:20:36 -0700171{
172 static unsigned char called = 0;
173 struct Scsi_Host *instance;
174 unsigned long address;
175 unsigned int epc;
176 struct zorro_dev *z = NULL;
177 unsigned int default_dma_xfer_mask;
178 wd33c93_regs regs;
179 int num_gvp11 = 0;
180#ifdef CHECK_WD33C93
181 volatile unsigned char *sasr_3393, *scmd_3393;
182 unsigned char save_sasr;
183 unsigned char q, qq;
184#endif
185
186 if (!MACH_IS_AMIGA || called)
187 return 0;
188 called = 1;
189
190 tpnt->proc_name = "GVP11";
191 tpnt->proc_info = &wd33c93_proc_info;
192
193 while ((z = zorro_find_device(ZORRO_WILDCARD, z))) {
194 /*
195 * This should (hopefully) be the correct way to identify
196 * all the different GVP SCSI controllers (except for the
197 * SERIES I though).
198 */
199
200 if (z->id == ZORRO_PROD_GVP_COMBO_030_R3_SCSI ||
201 z->id == ZORRO_PROD_GVP_SERIES_II)
202 default_dma_xfer_mask = ~0x00ffffff;
203 else if (z->id == ZORRO_PROD_GVP_GFORCE_030_SCSI ||
204 z->id == ZORRO_PROD_GVP_A530_SCSI ||
205 z->id == ZORRO_PROD_GVP_COMBO_030_R4_SCSI)
206 default_dma_xfer_mask = ~0x01ffffff;
207 else if (z->id == ZORRO_PROD_GVP_A1291 ||
208 z->id == ZORRO_PROD_GVP_GFORCE_040_SCSI_1)
209 default_dma_xfer_mask = ~0x07ffffff;
210 else
211 continue;
212
213 /*
214 * Rumors state that some GVP ram boards use the same product
215 * code as the SCSI controllers. Therefore if the board-size
216 * is not 64KB we asume it is a ram board and bail out.
217 */
218 if (z->resource.end-z->resource.start != 0xffff)
219 continue;
220
221 address = z->resource.start;
222 if (!request_mem_region(address, 256, "wd33c93"))
223 continue;
224
225#ifdef CHECK_WD33C93
226
227 /*
228 * These darn GVP boards are a problem - it can be tough to tell
229 * whether or not they include a SCSI controller. This is the
230 * ultimate Yet-Another-GVP-Detection-Hack in that it actually
231 * probes for a WD33c93 chip: If we find one, it's extremely
232 * likely that this card supports SCSI, regardless of Product_
233 * Code, Board_Size, etc.
234 */
235
236 /* Get pointers to the presumed register locations and save contents */
237
238 sasr_3393 = &(((gvp11_scsiregs *)(ZTWO_VADDR(address)))->SASR);
239 scmd_3393 = &(((gvp11_scsiregs *)(ZTWO_VADDR(address)))->SCMD);
240 save_sasr = *sasr_3393;
241
242 /* First test the AuxStatus Reg */
243
244 q = *sasr_3393; /* read it */
245 if (q & 0x08) /* bit 3 should always be clear */
246 goto release;
247 *sasr_3393 = WD_AUXILIARY_STATUS; /* setup indirect address */
248 if (*sasr_3393 == WD_AUXILIARY_STATUS) { /* shouldn't retain the write */
249 *sasr_3393 = save_sasr; /* Oops - restore this byte */
250 goto release;
251 }
252 if (*sasr_3393 != q) { /* should still read the same */
253 *sasr_3393 = save_sasr; /* Oops - restore this byte */
254 goto release;
255 }
256 if (*scmd_3393 != q) /* and so should the image at 0x1f */
257 goto release;
258
259
260 /* Ok, we probably have a wd33c93, but let's check a few other places
261 * for good measure. Make sure that this works for both 'A and 'B
262 * chip versions.
263 */
264
265 *sasr_3393 = WD_SCSI_STATUS;
266 q = *scmd_3393;
267 *sasr_3393 = WD_SCSI_STATUS;
268 *scmd_3393 = ~q;
269 *sasr_3393 = WD_SCSI_STATUS;
270 qq = *scmd_3393;
271 *sasr_3393 = WD_SCSI_STATUS;
272 *scmd_3393 = q;
273 if (qq != q) /* should be read only */
274 goto release;
275 *sasr_3393 = 0x1e; /* this register is unimplemented */
276 q = *scmd_3393;
277 *sasr_3393 = 0x1e;
278 *scmd_3393 = ~q;
279 *sasr_3393 = 0x1e;
280 qq = *scmd_3393;
281 *sasr_3393 = 0x1e;
282 *scmd_3393 = q;
283 if (qq != q || qq != 0xff) /* should be read only, all 1's */
284 goto release;
285 *sasr_3393 = WD_TIMEOUT_PERIOD;
286 q = *scmd_3393;
287 *sasr_3393 = WD_TIMEOUT_PERIOD;
288 *scmd_3393 = ~q;
289 *sasr_3393 = WD_TIMEOUT_PERIOD;
290 qq = *scmd_3393;
291 *sasr_3393 = WD_TIMEOUT_PERIOD;
292 *scmd_3393 = q;
293 if (qq != (~q & 0xff)) /* should be read/write */
294 goto release;
295#endif
296
297 instance = scsi_register (tpnt, sizeof (struct WD33C93_hostdata));
298 if(instance == NULL)
299 goto release;
300 instance->base = ZTWO_VADDR(address);
301 instance->irq = IRQ_AMIGA_PORTS;
302 instance->unique_id = z->slotaddr;
303
304 if (gvp11_xfer_mask)
305 HDATA(instance)->dma_xfer_mask = gvp11_xfer_mask;
306 else
307 HDATA(instance)->dma_xfer_mask = default_dma_xfer_mask;
308
309
310 DMA(instance)->secret2 = 1;
311 DMA(instance)->secret1 = 0;
312 DMA(instance)->secret3 = 15;
313 while (DMA(instance)->CNTR & GVP11_DMAC_BUSY) ;
314 DMA(instance)->CNTR = 0;
315
316 DMA(instance)->BANK = 0;
317
318 epc = *(unsigned short *)(ZTWO_VADDR(address) + 0x8000);
319
320 /*
321 * Check for 14MHz SCSI clock
322 */
323 regs.SASR = &(DMA(instance)->SASR);
324 regs.SCMD = &(DMA(instance)->SCMD);
James Bottomleya579dab2008-03-31 22:06:50 -0500325 HDATA(instance)->no_sync = 0xff;
326 HDATA(instance)->fast = 0;
327 HDATA(instance)->dma_mode = CTRL_DMA;
Linus Torvalds1da177e2005-04-16 15:20:36 -0700328 wd33c93_init(instance, regs, dma_setup, dma_stop,
329 (epc & GVP_SCSICLKMASK) ? WD33C93_FS_8_10
330 : WD33C93_FS_12_15);
331
Thomas Gleixner1d6f3592006-07-01 19:29:42 -0700332 request_irq(IRQ_AMIGA_PORTS, gvp11_intr, IRQF_SHARED, "GVP11 SCSI",
Linus Torvalds1da177e2005-04-16 15:20:36 -0700333 instance);
334 DMA(instance)->CNTR = GVP11_DMAC_INT_ENABLE;
335 num_gvp11++;
336 continue;
337
338release:
339 release_mem_region(address, 256);
340 }
341
342 return num_gvp11;
343}
344
Henrik Kretzschmar65396412006-09-12 23:49:33 +0200345static int gvp11_bus_reset(struct scsi_cmnd *cmd)
Linus Torvalds1da177e2005-04-16 15:20:36 -0700346{
347 /* FIXME perform bus-specific reset */
Jeff Garzik 68b3aa72005-05-28 07:56:31 -0400348
Jeff Garzik df0ae242005-05-28 07:57:14 -0400349 /* FIXME 2: shouldn't we no-op this function (return
350 FAILED), and fall back to host reset function,
351 wd33c93_host_reset ? */
352
Jeff Garzik 68b3aa72005-05-28 07:56:31 -0400353 spin_lock_irq(cmd->device->host->host_lock);
Linus Torvalds1da177e2005-04-16 15:20:36 -0700354 wd33c93_host_reset(cmd);
Jeff Garzik 68b3aa72005-05-28 07:56:31 -0400355 spin_unlock_irq(cmd->device->host->host_lock);
356
Linus Torvalds1da177e2005-04-16 15:20:36 -0700357 return SUCCESS;
358}
359
360
361#define HOSTS_C
362
363#include "gvp11.h"
364
Christoph Hellwigd0be4a7d2005-10-31 18:31:40 +0100365static struct scsi_host_template driver_template = {
Linus Torvalds1da177e2005-04-16 15:20:36 -0700366 .proc_name = "GVP11",
367 .name = "GVP Series II SCSI",
368 .detect = gvp11_detect,
369 .release = gvp11_release,
370 .queuecommand = wd33c93_queuecommand,
371 .eh_abort_handler = wd33c93_abort,
372 .eh_bus_reset_handler = gvp11_bus_reset,
373 .eh_host_reset_handler = wd33c93_host_reset,
374 .can_queue = CAN_QUEUE,
375 .this_id = 7,
376 .sg_tablesize = SG_ALL,
377 .cmd_per_lun = CMD_PER_LUN,
378 .use_clustering = DISABLE_CLUSTERING
379};
380
381
382#include "scsi_module.c"
383
384int gvp11_release(struct Scsi_Host *instance)
385{
386#ifdef MODULE
387 DMA(instance)->CNTR = 0;
388 release_mem_region(ZTWO_PADDR(instance->base), 256);
389 free_irq(IRQ_AMIGA_PORTS, instance);
390 wd33c93_release();
391#endif
392 return 1;
393}
394
395MODULE_LICENSE("GPL");