include/linux/i2c/twl4030.h

/*
 * twl4030.h - header for TWL4030 PM and audio CODEC device
 *
 * Copyright (C) 2005-2006 Texas Instruments, Inc.
 *
 * Based on tlv320aic23.c:
 * Copyright (c) by Kai Svahn <kai.svahn@nokia.com>
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation; either version 2 of the License, or
 * (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program; if not, write to the Free Software
 * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307 USA
 *
 */

#ifndef __TWL4030_H_
#define __TWL4030_H_

/*
 * Using the twl4030 core we address registers using a pair
 *	{ module id, relative register offset }
 * which that core then maps to the relevant
 *	{ i2c slave, absolute register address }
 *
 * The module IDs are meaningful only to the twl4030 core code,
 * which uses them as array indices to look up the first register
 * address each module uses within a given i2c slave.
 */

/* Slave 0 (i2c address 0x48) */
#define TWL4030_MODULE_USB		0x00

/* Slave 1 (i2c address 0x49) */
#define TWL4030_MODULE_AUDIO_VOICE	0x01
#define TWL4030_MODULE_GPIO		0x02
#define TWL4030_MODULE_INTBR		0x03
#define TWL4030_MODULE_PIH		0x04
#define TWL4030_MODULE_TEST		0x05

/* Slave 2 (i2c address 0x4a) */
#define TWL4030_MODULE_KEYPAD		0x06
#define TWL4030_MODULE_MADC		0x07
#define TWL4030_MODULE_INTERRUPTS	0x08
#define TWL4030_MODULE_LED		0x09
#define TWL4030_MODULE_MAIN_CHARGE	0x0A
#define TWL4030_MODULE_PRECHARGE	0x0B
#define TWL4030_MODULE_PWM0		0x0C
#define TWL4030_MODULE_PWM1		0x0D
#define TWL4030_MODULE_PWMA		0x0E
#define TWL4030_MODULE_PWMB		0x0F

/* Slave 3 (i2c address 0x4b) */
#define TWL4030_MODULE_BACKUP		0x10
#define TWL4030_MODULE_INT		0x11
#define TWL4030_MODULE_PM_MASTER	0x12
#define TWL4030_MODULE_PM_RECEIVER	0x13
#define TWL4030_MODULE_RTC		0x14
#define TWL4030_MODULE_SECURED_REG	0x15

/*
 * Read and write single 8-bit registers
 */
int twl4030_i2c_write_u8(u8 mod_no, u8 val, u8 reg);
int twl4030_i2c_read_u8(u8 mod_no, u8 *val, u8 reg);

/*
 * Read and write several 8-bit registers at once.
 *
 * IMPORTANT:  For twl4030_i2c_write(), allocate num_bytes + 1
 * for the value, and populate your data starting at offset 1.
 */
int twl4030_i2c_write(u8 mod_no, u8 *value, u8 reg, u8 num_bytes);
int twl4030_i2c_read(u8 mod_no, u8 *value, u8 reg, u8 num_bytes);

/*----------------------------------------------------------------------*/

/*
 * NOTE:  at up to 1024 registers, this is a big chip.
 *
 * Avoid putting register declarations in this file, instead of into
 * a driver-private file, unless some of the registers in a block
 * need to be shared with other drivers.  One example is blocks that
 * have Secondary IRQ Handler (SIH) registers.
 */

#define TWL4030_SIH_CTRL_EXCLEN_MASK	BIT(0)
#define TWL4030_SIH_CTRL_PENDDIS_MASK	BIT(1)
#define TWL4030_SIH_CTRL_COR_MASK	BIT(2)

/*----------------------------------------------------------------------*/

/*
 * GPIO Block Register offsets (use TWL4030_MODULE_GPIO)
 */

#define REG_GPIODATAIN1			0x0
#define REG_GPIODATAIN2			0x1
#define REG_GPIODATAIN3			0x2
#define REG_GPIODATADIR1		0x3
#define REG_GPIODATADIR2		0x4
#define REG_GPIODATADIR3		0x5
#define REG_GPIODATAOUT1		0x6
#define REG_GPIODATAOUT2		0x7
#define REG_GPIODATAOUT3		0x8
#define REG_CLEARGPIODATAOUT1		0x9
#define REG_CLEARGPIODATAOUT2		0xA
#define REG_CLEARGPIODATAOUT3		0xB
#define REG_SETGPIODATAOUT1		0xC
#define REG_SETGPIODATAOUT2		0xD
#define REG_SETGPIODATAOUT3		0xE
#define REG_GPIO_DEBEN1			0xF
#define REG_GPIO_DEBEN2			0x10
#define REG_GPIO_DEBEN3			0x11
#define REG_GPIO_CTRL			0x12
#define REG_GPIOPUPDCTR1		0x13
#define REG_GPIOPUPDCTR2		0x14
#define REG_GPIOPUPDCTR3		0x15
#define REG_GPIOPUPDCTR4		0x16
#define REG_GPIOPUPDCTR5		0x17
#define REG_GPIO_ISR1A			0x19
#define REG_GPIO_ISR2A			0x1A
#define REG_GPIO_ISR3A			0x1B
#define REG_GPIO_IMR1A			0x1C
#define REG_GPIO_IMR2A			0x1D
#define REG_GPIO_IMR3A			0x1E
#define REG_GPIO_ISR1B			0x1F
#define REG_GPIO_ISR2B			0x20
#define REG_GPIO_ISR3B			0x21
#define REG_GPIO_IMR1B			0x22
#define REG_GPIO_IMR2B			0x23
#define REG_GPIO_IMR3B			0x24
#define REG_GPIO_EDR1			0x28
#define REG_GPIO_EDR2			0x29
#define REG_GPIO_EDR3			0x2A
#define REG_GPIO_EDR4			0x2B
#define REG_GPIO_EDR5			0x2C
#define REG_GPIO_SIH_CTRL		0x2D

/* Up to 18 signals are available as GPIOs, when their
 * pins are not assigned to another use (such as ULPI/USB).
 */
#define TWL4030_GPIO_MAX		18

/*----------------------------------------------------------------------*/

/*
 * Keypad register offsets (use TWL4030_MODULE_KEYPAD)
 * ... SIH/interrupt only
 */

#define TWL4030_KEYPAD_KEYP_ISR1	0x11
#define TWL4030_KEYPAD_KEYP_IMR1	0x12
#define TWL4030_KEYPAD_KEYP_ISR2	0x13
#define TWL4030_KEYPAD_KEYP_IMR2	0x14
#define TWL4030_KEYPAD_KEYP_SIR		0x15	/* test register */
#define TWL4030_KEYPAD_KEYP_EDR		0x16
#define TWL4030_KEYPAD_KEYP_SIH_CTRL	0x17

/*----------------------------------------------------------------------*/

/*
 * Multichannel ADC register offsets (use TWL4030_MODULE_MADC)
 * ... SIH/interrupt only
 */

#define TWL4030_MADC_ISR1		0x61
#define TWL4030_MADC_IMR1		0x62
#define TWL4030_MADC_ISR2		0x63
#define TWL4030_MADC_IMR2		0x64
#define TWL4030_MADC_SIR		0x65	/* test register */
#define TWL4030_MADC_EDR		0x66
#define TWL4030_MADC_SIH_CTRL		0x67

/*----------------------------------------------------------------------*/

/*
 * Battery charger register offsets (use TWL4030_MODULE_INTERRUPTS)
 */

#define TWL4030_INTERRUPTS_BCIISR1A	0x0
#define TWL4030_INTERRUPTS_BCIISR2A	0x1
#define TWL4030_INTERRUPTS_BCIIMR1A	0x2
#define TWL4030_INTERRUPTS_BCIIMR2A	0x3
#define TWL4030_INTERRUPTS_BCIISR1B	0x4
#define TWL4030_INTERRUPTS_BCIISR2B	0x5
#define TWL4030_INTERRUPTS_BCIIMR1B	0x6
#define TWL4030_INTERRUPTS_BCIIMR2B	0x7
#define TWL4030_INTERRUPTS_BCISIR1	0x8	/* test register */
#define TWL4030_INTERRUPTS_BCISIR2	0x9	/* test register */
#define TWL4030_INTERRUPTS_BCIEDR1	0xa
#define TWL4030_INTERRUPTS_BCIEDR2	0xb
#define TWL4030_INTERRUPTS_BCIEDR3	0xc
#define TWL4030_INTERRUPTS_BCISIHCTRL	0xd

/*----------------------------------------------------------------------*/

/*
 * Power Interrupt block register offsets (use TWL4030_MODULE_INT)
 */

#define TWL4030_INT_PWR_ISR1		0x0
#define TWL4030_INT_PWR_IMR1		0x1
#define TWL4030_INT_PWR_ISR2		0x2
#define TWL4030_INT_PWR_IMR2		0x3
#define TWL4030_INT_PWR_SIR		0x4	/* test register */
#define TWL4030_INT_PWR_EDR1		0x5
#define TWL4030_INT_PWR_EDR2		0x6
#define TWL4030_INT_PWR_SIH_CTRL	0x7

/*----------------------------------------------------------------------*/

struct twl4030_bci_platform_data {
	int *battery_tmp_tbl;
	unsigned int tblsize;
};

/* TWL4030_GPIO_MAX (18) GPIOs, with interrupts */
struct twl4030_gpio_platform_data {
	int		gpio_base;
	unsigned	irq_base, irq_end;

	/* package the two LED signals as output-only GPIOs? */
	bool		use_leds;

	/* gpio-n should control VMMC(n+1) if BIT(n) in mmc_cd is set */
	u8		mmc_cd;

	/* For gpio-N, bit (1 << N) in "pullups" is set if that pullup
	 * should be enabled.  Else, if that bit is set in "pulldowns",
	 * that pulldown is enabled.  Don't waste power by letting any
	 * digital inputs float...
	 */
	u32		pullups;
	u32		pulldowns;

	int		(*setup)(struct device *dev,
				unsigned gpio, unsigned ngpio);
	int		(*teardown)(struct device *dev,
				unsigned gpio, unsigned ngpio);
};

struct twl4030_madc_platform_data {
	int		irq_line;
};

struct twl4030_keypad_data {
	int rows;
	int cols;
	int *keymap;
	int irq;
	unsigned int keymapsize;
	unsigned int rep:1;
};

enum twl4030_usb_mode {
	T2_USB_MODE_ULPI = 1,
	T2_USB_MODE_CEA2011_3PIN = 2,
};

struct twl4030_usb_data {
	enum twl4030_usb_mode	usb_mode;
};

struct twl4030_platform_data {
	unsigned				irq_base, irq_end;
	struct twl4030_bci_platform_data	*bci;
	struct twl4030_gpio_platform_data	*gpio;
	struct twl4030_madc_platform_data	*madc;
	struct twl4030_keypad_data		*keypad;
	struct twl4030_usb_data			*usb;

	/* REVISIT more to come ... _nothing_ should be hard-wired */
};

/*----------------------------------------------------------------------*/

int twl4030_sih_setup(int module);

/*
 * FIXME completely stop using TWL4030_IRQ_BASE ... instead, pass the
 * IRQ data to subsidiary devices using platform device resources.
 */

/* IRQ information-need base */
#include <mach/irqs.h>
/* TWL4030 interrupts */

/* #define TWL4030_MODIRQ_GPIO		(TWL4030_IRQ_BASE + 0) */
#define TWL4030_MODIRQ_KEYPAD		(TWL4030_IRQ_BASE + 1)
#define TWL4030_MODIRQ_BCI		(TWL4030_IRQ_BASE + 2)
#define TWL4030_MODIRQ_MADC		(TWL4030_IRQ_BASE + 3)
/* #define TWL4030_MODIRQ_USB		(TWL4030_IRQ_BASE + 4) */
/* #define TWL4030_MODIRQ_PWR		(TWL4030_IRQ_BASE + 5) */

#define TWL4030_PWRIRQ_PWRBTN		(TWL4030_PWR_IRQ_BASE + 0)
/* #define TWL4030_PWRIRQ_CHG_PRES		(TWL4030_PWR_IRQ_BASE + 1) */
/* #define TWL4030_PWRIRQ_USB_PRES		(TWL4030_PWR_IRQ_BASE + 2) */
/* #define TWL4030_PWRIRQ_RTC		(TWL4030_PWR_IRQ_BASE + 3) */
/* #define TWL4030_PWRIRQ_HOT_DIE		(TWL4030_PWR_IRQ_BASE + 4) */
/* #define TWL4030_PWRIRQ_PWROK_TIMEOUT	(TWL4030_PWR_IRQ_BASE + 5) */
/* #define TWL4030_PWRIRQ_MBCHG		(TWL4030_PWR_IRQ_BASE + 6) */
/* #define TWL4030_PWRIRQ_SC_DETECT	(TWL4030_PWR_IRQ_BASE + 7) */

/* Rest are unsued currently*/

/* Offsets to Power Registers */
#define TWL4030_VDAC_DEV_GRP		0x3B
#define TWL4030_VDAC_DEDICATED		0x3E
#define TWL4030_VAUX1_DEV_GRP		0x17
#define TWL4030_VAUX1_DEDICATED		0x1A
#define TWL4030_VAUX2_DEV_GRP		0x1B
#define TWL4030_VAUX2_DEDICATED		0x1E
#define TWL4030_VAUX3_DEV_GRP		0x1F
#define TWL4030_VAUX3_DEDICATED		0x22

/* TWL4030 GPIO interrupt definitions */

#define TWL4030_GPIO_IRQ_NO(n)		(TWL4030_GPIO_IRQ_BASE + (n))

/*
 * Exported TWL4030 GPIO APIs
 *
 * WARNING -- use standard GPIO and IRQ calls instead; these will vanish.
 */
int twl4030_set_gpio_debounce(int gpio, int enable);

#if defined(CONFIG_TWL4030_BCI_BATTERY) || \
	defined(CONFIG_TWL4030_BCI_BATTERY_MODULE)
	extern int twl4030charger_usb_en(int enable);
#else
	static inline int twl4030charger_usb_en(int enable) { return 0; }
#endif

#endif /* End of __TWL4030_H */