Eric Bénard | 9a4cc05 | 2013-12-05 14:28:06 +0100 | [diff] [blame] | 1 | /* |
| 2 | * Copyright 2013 Eukréa Electromatique <eric@eukrea.com> |
| 3 | * Copyright 2013 Eukréa Electromatique <denis@eukrea.com> |
| 4 | * |
| 5 | * This program is free software; you can redistribute it and/or |
| 6 | * modify it under the terms of the GNU General Public License |
| 7 | * as published by the Free Software Foundation; either version 2 |
| 8 | * of the License, or (at your option) any later version. |
| 9 | * This program is distributed in the hope that it will be useful, |
| 10 | * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| 11 | * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| 12 | * GNU General Public License for more details. |
| 13 | */ |
| 14 | |
| 15 | /* |
| 16 | * Module contains : i.MX282 + 64MB DDR2 + NAND + Ethernet PHY + RTC |
| 17 | */ |
| 18 | |
| 19 | /dts-v1/; |
| 20 | #include "imx28-eukrea-mbmx28lc.dtsi" |
| 21 | |
| 22 | / { |
| 23 | model = "Eukrea Electromatique MBMX283LC"; |
| 24 | compatible = "eukrea,mbmx283lc", "eukrea,mbmx28lc", "fsl,imx28"; |
| 25 | |
| 26 | memory { |
| 27 | reg = <0x40000000 0x04000000>; |
| 28 | }; |
| 29 | }; |
| 30 | |
| 31 | &gpmi { |
| 32 | pinctrl-names = "default"; |
| 33 | pinctrl-0 = <&gpmi_pins_a>; |
| 34 | status = "okay"; |
| 35 | }; |
| 36 | |
| 37 | &i2c0 { |
| 38 | pinctrl-names = "default"; |
| 39 | pinctrl-0 = <&i2c0_pins_a>; |
| 40 | status = "okay"; |
| 41 | |
| 42 | pcf8563: rtc@51 { |
| 43 | compatible = "nxp,pcf8563"; |
| 44 | reg = <0x51>; |
| 45 | }; |
| 46 | }; |
| 47 | |
| 48 | |
| 49 | &mac0 { |
| 50 | phy-mode = "rmii"; |
| 51 | pinctrl-names = "default"; |
| 52 | pinctrl-0 = <&mac0_pins_a>; |
| 53 | phy-reset-gpios = <&gpio4 13 GPIO_ACTIVE_LOW>; |
| 54 | status = "okay"; |
| 55 | }; |
| 56 | |
| 57 | &pinctrl{ |
| 58 | pinctrl-names = "default"; |
| 59 | pinctrl-0 = <&hog_pins_cpuimx283>; |
| 60 | |
| 61 | hog_pins_cpuimx283: hog-cpuimx283@0 { |
| 62 | reg = <0>; |
| 63 | fsl,pinmux-ids = < |
| 64 | MX28_PAD_ENET0_RX_CLK__GPIO_4_13 |
| 65 | MX28_PAD_ENET0_TX_CLK__GPIO_4_5 |
| 66 | >; |
| 67 | fsl,drive-strength = <MXS_DRIVE_4mA>; |
| 68 | fsl,voltage = <MXS_VOLTAGE_HIGH>; |
| 69 | fsl,pull-up = <MXS_PULL_ENABLE>; |
| 70 | }; |
| 71 | }; |