blob: 5f5af9a606f8aaddbb4b8724a651db14e5ecee05 [file] [log] [blame]
Linus Torvalds1da177e2005-04-16 15:20:36 -07001/*****************************************************************************/
2
3/*
4 * baycom_par.c -- baycom par96 and picpar radio modem driver.
5 *
6 * Copyright (C) 1996-2000 Thomas Sailer (sailer@ife.ee.ethz.ch)
7 *
8 * This program is free software; you can redistribute it and/or modify
9 * it under the terms of the GNU General Public License as published by
10 * the Free Software Foundation; either version 2 of the License, or
11 * (at your option) any later version.
12 *
13 * This program is distributed in the hope that it will be useful,
14 * but WITHOUT ANY WARRANTY; without even the implied warranty of
15 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
16 * GNU General Public License for more details.
17 *
18 * You should have received a copy of the GNU General Public License
19 * along with this program; if not, write to the Free Software
20 * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
21 *
22 * Please note that the GPL allows you to use the driver, NOT the radio.
23 * In order to use the radio, you need a license from the communications
24 * authority of your country.
25 *
26 *
27 * Supported modems
28 *
29 * par96: This is a modem for 9600 baud FSK compatible to the G3RUH standard.
30 * The modem does all the filtering and regenerates the receiver clock.
31 * Data is transferred from and to the PC via a shift register.
32 * The shift register is filled with 16 bits and an interrupt is
33 * signalled. The PC then empties the shift register in a burst. This
34 * modem connects to the parallel port, hence the name. The modem
35 * leaves the implementation of the HDLC protocol and the scrambler
36 * polynomial to the PC. This modem is no longer available (at least
37 * from Baycom) and has been replaced by the PICPAR modem (see below).
38 * You may however still build one from the schematics published in
39 * cq-DL :-).
40 *
41 * picpar: This is a redesign of the par96 modem by Henning Rech, DF9IC. The
42 * modem is protocol compatible to par96, but uses only three low
43 * power ICs and can therefore be fed from the parallel port and
44 * does not require an additional power supply. It features
45 * built in DCD circuitry. The driver should therefore be configured
46 * for hardware DCD.
47 *
48 *
49 * Command line options (insmod command line)
50 *
51 * mode driver mode string. Valid choices are par96 and picpar.
52 * iobase base address of the port; common values are 0x378, 0x278, 0x3bc
53 *
54 *
55 * History:
56 * 0.1 26.06.1996 Adapted from baycom.c and made network driver interface
57 * 18.10.1996 Changed to new user space access routines (copy_{to,from}_user)
58 * 0.3 26.04.1997 init code/data tagged
59 * 0.4 08.07.1997 alternative ser12 decoding algorithm (uses delta CTS ints)
60 * 0.5 11.11.1997 split into separate files for ser12/par96
61 * 0.6 03.08.1999 adapt to Linus' new __setup/__initcall
62 * removed some pre-2.2 kernel compatibility cruft
63 * 0.7 10.08.1999 Check if parport can do SPP and is safe to access during interrupt contexts
64 * 0.8 12.02.2000 adapted to softnet driver interface
65 * removed direct parport access, uses parport driver methods
66 * 0.9 03.07.2000 fix interface name handling
67 */
68
69/*****************************************************************************/
70
71#include <linux/module.h>
72#include <linux/kernel.h>
73#include <linux/types.h>
74#include <linux/fcntl.h>
75#include <linux/interrupt.h>
76#include <linux/ioport.h>
77#include <linux/in.h>
78#include <linux/string.h>
79#include <linux/init.h>
80#include <linux/delay.h>
81#include <linux/errno.h>
82#include <linux/netdevice.h>
83#include <linux/hdlcdrv.h>
84#include <linux/baycom.h>
85#include <linux/parport.h>
86#include <linux/bitops.h>
Marcelo Feitoza Parisicd8749b2005-07-15 11:16:42 +010087#include <linux/jiffies.h>
Linus Torvalds1da177e2005-04-16 15:20:36 -070088
Linus Torvalds1da177e2005-04-16 15:20:36 -070089#include <asm/system.h>
90#include <asm/uaccess.h>
91
92/* --------------------------------------------------------------------- */
93
94#define BAYCOM_DEBUG
95
96/*
97 * modem options; bit mask
98 */
99#define BAYCOM_OPTIONS_SOFTDCD 1
100
101/* --------------------------------------------------------------------- */
102
103static const char bc_drvname[] = "baycom_par";
104static const char bc_drvinfo[] = KERN_INFO "baycom_par: (C) 1996-2000 Thomas Sailer, HB9JNX/AE4WA\n"
Joe Perchesad361c92009-07-06 13:05:40 -0700105"baycom_par: version 0.9 compiled " __TIME__ " " __DATE__ "\n";
Linus Torvalds1da177e2005-04-16 15:20:36 -0700106
107/* --------------------------------------------------------------------- */
108
109#define NR_PORTS 4
110
111static struct net_device *baycom_device[NR_PORTS];
112
113/* --------------------------------------------------------------------- */
114
115#define PAR96_BURSTBITS 16
116#define PAR96_BURST 4
117#define PAR96_PTT 2
118#define PAR96_TXBIT 1
119#define PAR96_ACK 0x40
120#define PAR96_RXBIT 0x20
121#define PAR96_DCD 0x10
122#define PAR97_POWER 0xf8
123
124/* ---------------------------------------------------------------------- */
125/*
126 * Information that need to be kept for each board.
127 */
128
129struct baycom_state {
130 struct hdlcdrv_state hdrv;
131
132 struct pardevice *pdev;
133 unsigned int options;
134
135 struct modem_state {
136 short arb_divider;
137 unsigned char flags;
138 unsigned int shreg;
139 struct modem_state_par96 {
140 int dcd_count;
141 unsigned int dcd_shreg;
142 unsigned long descram;
143 unsigned long scram;
144 } par96;
145 } modem;
146
147#ifdef BAYCOM_DEBUG
148 struct debug_vals {
149 unsigned long last_jiffies;
150 unsigned cur_intcnt;
151 unsigned last_intcnt;
152 int cur_pllcorr;
153 int last_pllcorr;
154 } debug_vals;
155#endif /* BAYCOM_DEBUG */
156};
157
158/* --------------------------------------------------------------------- */
159
160static void __inline__ baycom_int_freq(struct baycom_state *bc)
161{
162#ifdef BAYCOM_DEBUG
163 unsigned long cur_jiffies = jiffies;
164 /*
165 * measure the interrupt frequency
166 */
167 bc->debug_vals.cur_intcnt++;
Marcelo Feitoza Parisicd8749b2005-07-15 11:16:42 +0100168 if (time_after_eq(cur_jiffies, bc->debug_vals.last_jiffies + HZ)) {
Linus Torvalds1da177e2005-04-16 15:20:36 -0700169 bc->debug_vals.last_jiffies = cur_jiffies;
170 bc->debug_vals.last_intcnt = bc->debug_vals.cur_intcnt;
171 bc->debug_vals.cur_intcnt = 0;
172 bc->debug_vals.last_pllcorr = bc->debug_vals.cur_pllcorr;
173 bc->debug_vals.cur_pllcorr = 0;
174 }
175#endif /* BAYCOM_DEBUG */
176}
177
178/* --------------------------------------------------------------------- */
179/*
180 * ===================== PAR96 specific routines =========================
181 */
182
183#define PAR96_DESCRAM_TAP1 0x20000
184#define PAR96_DESCRAM_TAP2 0x01000
185#define PAR96_DESCRAM_TAP3 0x00001
186
187#define PAR96_DESCRAM_TAPSH1 17
188#define PAR96_DESCRAM_TAPSH2 12
189#define PAR96_DESCRAM_TAPSH3 0
190
191#define PAR96_SCRAM_TAP1 0x20000 /* X^17 */
192#define PAR96_SCRAM_TAPN 0x00021 /* X^0+X^5 */
193
194/* --------------------------------------------------------------------- */
195
196static __inline__ void par96_tx(struct net_device *dev, struct baycom_state *bc)
197{
198 int i;
199 unsigned int data = hdlcdrv_getbits(&bc->hdrv);
200 struct parport *pp = bc->pdev->port;
201
202 for(i = 0; i < PAR96_BURSTBITS; i++, data >>= 1) {
203 unsigned char val = PAR97_POWER;
204 bc->modem.par96.scram = ((bc->modem.par96.scram << 1) |
205 (bc->modem.par96.scram & 1));
206 if (!(data & 1))
207 bc->modem.par96.scram ^= 1;
208 if (bc->modem.par96.scram & (PAR96_SCRAM_TAP1 << 1))
209 bc->modem.par96.scram ^=
210 (PAR96_SCRAM_TAPN << 1);
211 if (bc->modem.par96.scram & (PAR96_SCRAM_TAP1 << 2))
212 val |= PAR96_TXBIT;
213 pp->ops->write_data(pp, val);
214 pp->ops->write_data(pp, val | PAR96_BURST);
215 }
216}
217
218/* --------------------------------------------------------------------- */
219
220static __inline__ void par96_rx(struct net_device *dev, struct baycom_state *bc)
221{
222 int i;
223 unsigned int data, mask, mask2, descx;
224 struct parport *pp = bc->pdev->port;
225
226 /*
227 * do receiver; differential decode and descramble on the fly
228 */
229 for(data = i = 0; i < PAR96_BURSTBITS; i++) {
230 bc->modem.par96.descram = (bc->modem.par96.descram << 1);
231 if (pp->ops->read_status(pp) & PAR96_RXBIT)
232 bc->modem.par96.descram |= 1;
233 descx = bc->modem.par96.descram ^
234 (bc->modem.par96.descram >> 1);
235 /* now the diff decoded data is inverted in descram */
236 pp->ops->write_data(pp, PAR97_POWER | PAR96_PTT);
237 descx ^= ((descx >> PAR96_DESCRAM_TAPSH1) ^
238 (descx >> PAR96_DESCRAM_TAPSH2));
239 data >>= 1;
240 if (!(descx & 1))
241 data |= 0x8000;
242 pp->ops->write_data(pp, PAR97_POWER | PAR96_PTT | PAR96_BURST);
243 }
244 hdlcdrv_putbits(&bc->hdrv, data);
245 /*
246 * do DCD algorithm
247 */
248 if (bc->options & BAYCOM_OPTIONS_SOFTDCD) {
249 bc->modem.par96.dcd_shreg = (bc->modem.par96.dcd_shreg >> 16)
250 | (data << 16);
251 /* search for flags and set the dcd counter appropriately */
252 for(mask = 0x1fe00, mask2 = 0xfc00, i = 0;
253 i < PAR96_BURSTBITS; i++, mask <<= 1, mask2 <<= 1)
254 if ((bc->modem.par96.dcd_shreg & mask) == mask2)
255 bc->modem.par96.dcd_count = HDLCDRV_MAXFLEN+4;
256 /* check for abort/noise sequences */
257 for(mask = 0x1fe00, mask2 = 0x1fe00, i = 0;
258 i < PAR96_BURSTBITS; i++, mask <<= 1, mask2 <<= 1)
259 if (((bc->modem.par96.dcd_shreg & mask) == mask2) &&
260 (bc->modem.par96.dcd_count >= 0))
261 bc->modem.par96.dcd_count -= HDLCDRV_MAXFLEN-10;
262 /* decrement and set the dcd variable */
263 if (bc->modem.par96.dcd_count >= 0)
264 bc->modem.par96.dcd_count -= 2;
265 hdlcdrv_setdcd(&bc->hdrv, bc->modem.par96.dcd_count > 0);
266 } else {
267 hdlcdrv_setdcd(&bc->hdrv, !!(pp->ops->read_status(pp) & PAR96_DCD));
268 }
269}
270
271/* --------------------------------------------------------------------- */
272
Jeff Garzik5712cb32007-10-19 02:54:26 -0400273static void par96_interrupt(void *dev_id)
Linus Torvalds1da177e2005-04-16 15:20:36 -0700274{
Jeff Garzik5712cb32007-10-19 02:54:26 -0400275 struct net_device *dev = dev_id;
Linus Torvalds1da177e2005-04-16 15:20:36 -0700276 struct baycom_state *bc = netdev_priv(dev);
277
278 baycom_int_freq(bc);
279 /*
280 * check if transmitter active
281 */
282 if (hdlcdrv_ptt(&bc->hdrv))
283 par96_tx(dev, bc);
284 else {
285 par96_rx(dev, bc);
286 if (--bc->modem.arb_divider <= 0) {
287 bc->modem.arb_divider = 6;
288 local_irq_enable();
289 hdlcdrv_arbitrate(dev, &bc->hdrv);
290 }
291 }
292 local_irq_enable();
293 hdlcdrv_transmitter(dev, &bc->hdrv);
294 hdlcdrv_receiver(dev, &bc->hdrv);
295 local_irq_disable();
296}
297
298/* --------------------------------------------------------------------- */
299
300static void par96_wakeup(void *handle)
301{
302 struct net_device *dev = (struct net_device *)handle;
303 struct baycom_state *bc = netdev_priv(dev);
304
305 printk(KERN_DEBUG "baycom_par: %s: why am I being woken up?\n", dev->name);
306 if (!parport_claim(bc->pdev))
307 printk(KERN_DEBUG "baycom_par: %s: I'm broken.\n", dev->name);
308}
309
310/* --------------------------------------------------------------------- */
311
312static int par96_open(struct net_device *dev)
313{
314 struct baycom_state *bc = netdev_priv(dev);
315 struct parport *pp;
316
317 if (!dev || !bc)
318 return -ENXIO;
319 pp = parport_find_base(dev->base_addr);
320 if (!pp) {
321 printk(KERN_ERR "baycom_par: parport at 0x%lx unknown\n", dev->base_addr);
322 return -ENXIO;
323 }
324 if (pp->irq < 0) {
325 printk(KERN_ERR "baycom_par: parport at 0x%lx has no irq\n", pp->base);
326 parport_put_port(pp);
327 return -ENXIO;
328 }
329 if ((~pp->modes) & (PARPORT_MODE_PCSPP | PARPORT_MODE_SAFEININT)) {
330 printk(KERN_ERR "baycom_par: parport at 0x%lx cannot be used\n", pp->base);
331 parport_put_port(pp);
332 return -ENXIO;
333 }
334 memset(&bc->modem, 0, sizeof(bc->modem));
335 bc->hdrv.par.bitrate = 9600;
336 bc->pdev = parport_register_device(pp, dev->name, NULL, par96_wakeup,
337 par96_interrupt, PARPORT_DEV_EXCL, dev);
338 parport_put_port(pp);
339 if (!bc->pdev) {
340 printk(KERN_ERR "baycom_par: cannot register parport at 0x%lx\n", dev->base_addr);
341 return -ENXIO;
342 }
343 if (parport_claim(bc->pdev)) {
344 printk(KERN_ERR "baycom_par: parport at 0x%lx busy\n", pp->base);
345 parport_unregister_device(bc->pdev);
346 return -EBUSY;
347 }
348 pp = bc->pdev->port;
349 dev->irq = pp->irq;
350 pp->ops->data_forward(pp);
351 bc->hdrv.par.bitrate = 9600;
352 pp->ops->write_data(pp, PAR96_PTT | PAR97_POWER); /* switch off PTT */
353 pp->ops->enable_irq(pp);
354 printk(KERN_INFO "%s: par96 at iobase 0x%lx irq %u options 0x%x\n",
355 bc_drvname, dev->base_addr, dev->irq, bc->options);
356 return 0;
357}
358
359/* --------------------------------------------------------------------- */
360
361static int par96_close(struct net_device *dev)
362{
363 struct baycom_state *bc = netdev_priv(dev);
364 struct parport *pp;
365
366 if (!dev || !bc)
367 return -EINVAL;
368 pp = bc->pdev->port;
369 /* disable interrupt */
370 pp->ops->disable_irq(pp);
371 /* switch off PTT */
372 pp->ops->write_data(pp, PAR96_PTT | PAR97_POWER);
373 parport_release(bc->pdev);
374 parport_unregister_device(bc->pdev);
375 printk(KERN_INFO "%s: close par96 at iobase 0x%lx irq %u\n",
376 bc_drvname, dev->base_addr, dev->irq);
377 return 0;
378}
379
380/* --------------------------------------------------------------------- */
381/*
382 * ===================== hdlcdrv driver interface =========================
383 */
384
385static int baycom_ioctl(struct net_device *dev, struct ifreq *ifr,
386 struct hdlcdrv_ioctl *hi, int cmd);
387
388/* --------------------------------------------------------------------- */
389
390static struct hdlcdrv_ops par96_ops = {
391 .drvname = bc_drvname,
392 .drvinfo = bc_drvinfo,
393 .open = par96_open,
394 .close = par96_close,
395 .ioctl = baycom_ioctl
396};
397
398/* --------------------------------------------------------------------- */
399
400static int baycom_setmode(struct baycom_state *bc, const char *modestr)
401{
402 if (!strncmp(modestr, "picpar", 6))
403 bc->options = 0;
404 else if (!strncmp(modestr, "par96", 5))
405 bc->options = BAYCOM_OPTIONS_SOFTDCD;
406 else
407 bc->options = !!strchr(modestr, '*');
408 return 0;
409}
410
411/* --------------------------------------------------------------------- */
412
413static int baycom_ioctl(struct net_device *dev, struct ifreq *ifr,
414 struct hdlcdrv_ioctl *hi, int cmd)
415{
416 struct baycom_state *bc;
417 struct baycom_ioctl bi;
418
419 if (!dev)
420 return -EINVAL;
421
422 bc = netdev_priv(dev);
423 BUG_ON(bc->hdrv.magic != HDLCDRV_MAGIC);
424
425 if (cmd != SIOCDEVPRIVATE)
426 return -ENOIOCTLCMD;
427 switch (hi->cmd) {
428 default:
429 break;
430
431 case HDLCDRVCTL_GETMODE:
432 strcpy(hi->data.modename, bc->options ? "par96" : "picpar");
433 if (copy_to_user(ifr->ifr_data, hi, sizeof(struct hdlcdrv_ioctl)))
434 return -EFAULT;
435 return 0;
436
437 case HDLCDRVCTL_SETMODE:
438 if (netif_running(dev) || !capable(CAP_NET_ADMIN))
439 return -EACCES;
440 hi->data.modename[sizeof(hi->data.modename)-1] = '\0';
441 return baycom_setmode(bc, hi->data.modename);
442
443 case HDLCDRVCTL_MODELIST:
444 strcpy(hi->data.modename, "par96,picpar");
445 if (copy_to_user(ifr->ifr_data, hi, sizeof(struct hdlcdrv_ioctl)))
446 return -EFAULT;
447 return 0;
448
449 case HDLCDRVCTL_MODEMPARMASK:
450 return HDLCDRV_PARMASK_IOBASE;
451
452 }
453
454 if (copy_from_user(&bi, ifr->ifr_data, sizeof(bi)))
455 return -EFAULT;
456 switch (bi.cmd) {
457 default:
458 return -ENOIOCTLCMD;
459
460#ifdef BAYCOM_DEBUG
461 case BAYCOMCTL_GETDEBUG:
462 bi.data.dbg.debug1 = bc->hdrv.ptt_keyed;
463 bi.data.dbg.debug2 = bc->debug_vals.last_intcnt;
464 bi.data.dbg.debug3 = bc->debug_vals.last_pllcorr;
465 break;
466#endif /* BAYCOM_DEBUG */
467
468 }
469 if (copy_to_user(ifr->ifr_data, &bi, sizeof(bi)))
470 return -EFAULT;
471 return 0;
472
473}
474
475/* --------------------------------------------------------------------- */
476
477/*
478 * command line settable parameters
479 */
480static const char *mode[NR_PORTS] = { "picpar", };
481static int iobase[NR_PORTS] = { 0x378, };
482
483module_param_array(mode, charp, NULL, 0);
484MODULE_PARM_DESC(mode, "baycom operating mode; eg. par96 or picpar");
485module_param_array(iobase, int, NULL, 0);
486MODULE_PARM_DESC(iobase, "baycom io base address");
487
488MODULE_AUTHOR("Thomas M. Sailer, sailer@ife.ee.ethz.ch, hb9jnx@hb9w.che.eu");
489MODULE_DESCRIPTION("Baycom par96 and picpar amateur radio modem driver");
490MODULE_LICENSE("GPL");
491
492/* --------------------------------------------------------------------- */
493
494static int __init init_baycompar(void)
495{
496 int i, found = 0;
497 char set_hw = 1;
498
499 printk(bc_drvinfo);
500 /*
501 * register net devices
502 */
503 for (i = 0; i < NR_PORTS; i++) {
504 struct net_device *dev;
505 struct baycom_state *bc;
506 char ifname[IFNAMSIZ];
507
508 sprintf(ifname, "bcp%d", i);
509
510 if (!mode[i])
511 set_hw = 0;
512 if (!set_hw)
513 iobase[i] = 0;
514
515 dev = hdlcdrv_register(&par96_ops,
516 sizeof(struct baycom_state),
517 ifname, iobase[i], 0, 0);
518 if (IS_ERR(dev))
519 break;
520
521 bc = netdev_priv(dev);
522 if (set_hw && baycom_setmode(bc, mode[i]))
523 set_hw = 0;
524 found++;
525 baycom_device[i] = dev;
526 }
527
528 if (!found)
529 return -ENXIO;
530 return 0;
531}
532
533static void __exit cleanup_baycompar(void)
534{
535 int i;
536
537 for(i = 0; i < NR_PORTS; i++) {
538 struct net_device *dev = baycom_device[i];
539
540 if (dev)
541 hdlcdrv_unregister(dev);
542 }
543}
544
545module_init(init_baycompar);
546module_exit(cleanup_baycompar);
547
548/* --------------------------------------------------------------------- */
549
550#ifndef MODULE
551
552/*
553 * format: baycom_par=io,mode
554 * mode: par96,picpar
555 */
556
557static int __init baycom_par_setup(char *str)
558{
559 static unsigned nr_dev;
560 int ints[2];
561
562 if (nr_dev >= NR_PORTS)
563 return 0;
564 str = get_options(str, 2, ints);
565 if (ints[0] < 1)
566 return 0;
567 mode[nr_dev] = str;
568 iobase[nr_dev] = ints[1];
569 nr_dev++;
570 return 1;
571}
572
573__setup("baycom_par=", baycom_par_setup);
574
575#endif /* MODULE */
576/* --------------------------------------------------------------------- */