arch/powerpc/boot/dts/mpc8548cds.dtsi

/*
 * MPC8548CDS Device Tree Source stub (no addresses or top-level ranges)
 *
 * Copyright 2012 Freescale Semiconductor Inc.
 *
 * Redistribution and use in source and binary forms, with or without
 * modification, are permitted provided that the following conditions are met:
 *     * Redistributions of source code must retain the above copyright
 *       notice, this list of conditions and the following disclaimer.
 *     * Redistributions in binary form must reproduce the above copyright
 *       notice, this list of conditions and the following disclaimer in the
 *       documentation and/or other materials provided with the distribution.
 *     * Neither the name of Freescale Semiconductor nor the
 *       names of its contributors may be used to endorse or promote products
 *       derived from this software without specific prior written permission.
 *
 *
 * ALTERNATIVELY, this software may be distributed under the terms of the
 * GNU General Public License ("GPL") as published by the Free Software
 * Foundation, either version 2 of that License or (at your option) any
 * later version.
 *
 * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
 * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
 * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
 * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
 * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
 * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
 * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
 * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
 * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
 * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
 */

&board_lbc {
	nor@0,0 {
		#address-cells = <1>;
		#size-cells = <1>;
		compatible = "cfi-flash";
		reg = <0x0 0x0 0x01000000>;
		bank-width = <2>;
		device-width = <2>;

		partition@0 {
			reg = <0x0 0x0b00000>;
			label = "ramdisk-nor";
		};

		partition@300000 {
			reg = <0x0b00000 0x0400000>;
			label = "kernel-nor";
		};

		partition@700000 {
			reg = <0x0f00000 0x060000>;
			label = "dtb-nor";
		};

		partition@760000 {
			reg = <0x0f60000 0x020000>;
			label = "env-nor";
			read-only;
		};

		partition@780000 {
			reg = <0x0f80000 0x080000>;
			label = "u-boot-nor";
			read-only;
		};
	};

	board-control@1,0 {
		compatible = "fsl,mpc8548cds-fpga";
		reg = <0x1 0x0 0x1000>;
	};
};

&board_soc {
	i2c@3000 {
		eeprom@50 {
			compatible = "atmel,24c64";
			reg = <0x50>;
		};

		eeprom@56 {
			compatible = "atmel,24c64";
			reg = <0x56>;
		};

		eeprom@57 {
			compatible = "atmel,24c64";
			reg = <0x57>;
		};
	};

	i2c@3100 {
		eeprom@50 {
			compatible = "atmel,24c64";
			reg = <0x50>;
		};
	};

	enet0: ethernet@24000 {
		tbi-handle = <&tbi0>;
		phy-handle = <&phy0>;
	};

	mdio@24520 {
		phy0: ethernet-phy@0 {
			interrupts = <5 1 0 0>;
			reg = <0x0>;
			device_type = "ethernet-phy";
		};
		phy1: ethernet-phy@1 {
			interrupts = <5 1 0 0>;
			reg = <0x1>;
			device_type = "ethernet-phy";
		};
		phy2: ethernet-phy@2 {
			interrupts = <5 1 0 0>;
			reg = <0x2>;
			device_type = "ethernet-phy";
		};
		phy3: ethernet-phy@3 {
			interrupts = <5 1 0 0>;
			reg = <0x3>;
			device_type = "ethernet-phy";
		};
		tbi0: tbi-phy@11 {
			reg = <0x11>;
			device_type = "tbi-phy";
		};
	};

	enet1: ethernet@25000 {
		tbi-handle = <&tbi1>;
		phy-handle = <&phy1>;
	};

	mdio@25520 {
		tbi1: tbi-phy@11 {
			reg = <0x11>;
			device_type = "tbi-phy";
		};
	};

	enet2: ethernet@26000 {
		tbi-handle = <&tbi2>;
		phy-handle = <&phy2>;
	};

	mdio@26520 {
		tbi2: tbi-phy@11 {
			reg = <0x11>;
			device_type = "tbi-phy";
		};
	};

	enet3: ethernet@27000 {
		tbi-handle = <&tbi3>;
		phy-handle = <&phy3>;
	};

	mdio@27520 {
		tbi3: tbi-phy@11 {
			reg = <0x11>;
			device_type = "tbi-phy";
		};
	};
};

&board_pci0 {
	interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
	interrupt-map = <
		/* IDSEL 0x4 (PCIX Slot 2) */
		0x2000 0x0 0x0 0x1 &mpic 0x0 0x1 0 0
		0x2000 0x0 0x0 0x2 &mpic 0x1 0x1 0 0
		0x2000 0x0 0x0 0x3 &mpic 0x2 0x1 0 0
		0x2000 0x0 0x0 0x4 &mpic 0x3 0x1 0 0

		/* IDSEL 0x5 (PCIX Slot 3) */
		0x2800 0x0 0x0 0x1 &mpic 0x1 0x1 0 0
		0x2800 0x0 0x0 0x2 &mpic 0x2 0x1 0 0
		0x2800 0x0 0x0 0x3 &mpic 0x3 0x1 0 0
		0x2800 0x0 0x0 0x4 &mpic 0x0 0x1 0 0

		/* IDSEL 0x6 (PCIX Slot 4) */
		0x3000 0x0 0x0 0x1 &mpic 0x2 0x1 0 0
		0x3000 0x0 0x0 0x2 &mpic 0x3 0x1 0 0
		0x3000 0x0 0x0 0x3 &mpic 0x0 0x1 0 0
		0x3000 0x0 0x0 0x4 &mpic 0x1 0x1 0 0

		/* IDSEL 0x8 (PCIX Slot 5) */
		0x4000 0x0 0x0 0x1 &mpic 0x0 0x1 0 0
		0x4000 0x0 0x0 0x2 &mpic 0x1 0x1 0 0
		0x4000 0x0 0x0 0x3 &mpic 0x2 0x1 0 0
		0x4000 0x0 0x0 0x4 &mpic 0x3 0x1 0 0

		/* IDSEL 0xC (Tsi310 bridge) */
		0x6000 0x0 0x0 0x1 &mpic 0x0 0x1 0 0
		0x6000 0x0 0x0 0x2 &mpic 0x1 0x1 0 0
		0x6000 0x0 0x0 0x3 &mpic 0x2 0x1 0 0
		0x6000 0x0 0x0 0x4 &mpic 0x3 0x1 0 0

		/* IDSEL 0x14 (Slot 2) */
		0xa000 0x0 0x0 0x1 &mpic 0x0 0x1 0 0
		0xa000 0x0 0x0 0x2 &mpic 0x1 0x1 0 0
		0xa000 0x0 0x0 0x3 &mpic 0x2 0x1 0 0
		0xa000 0x0 0x0 0x4 &mpic 0x3 0x1 0 0

		/* IDSEL 0x15 (Slot 3) */
		0xa800 0x0 0x0 0x1 &mpic 0x1 0x1 0 0
		0xa800 0x0 0x0 0x2 &mpic 0x2 0x1 0 0
		0xa800 0x0 0x0 0x3 &mpic 0x3 0x1 0 0
		0xa800 0x0 0x0 0x4 &mpic 0x0 0x1 0 0

		/* IDSEL 0x16 (Slot 4) */
		0xb000 0x0 0x0 0x1 &mpic 0x2 0x1 0 0
		0xb000 0x0 0x0 0x2 &mpic 0x3 0x1 0 0
		0xb000 0x0 0x0 0x3 &mpic 0x0 0x1 0 0
		0xb000 0x0 0x0 0x4 &mpic 0x1 0x1 0 0

		/* IDSEL 0x18 (Slot 5) */
		0xc000 0x0 0x0 0x1 &mpic 0x0 0x1 0 0
		0xc000 0x0 0x0 0x2 &mpic 0x1 0x1 0 0
		0xc000 0x0 0x0 0x3 &mpic 0x2 0x1 0 0
		0xc000 0x0 0x0 0x4 &mpic 0x3 0x1 0 0

		/* IDSEL 0x1C (Tsi310 bridge PCI primary) */
		0xe000 0x0 0x0 0x1 &mpic 0x0 0x1 0 0
		0xe000 0x0 0x0 0x2 &mpic 0x1 0x1 0 0
		0xe000 0x0 0x0 0x3 &mpic 0x2 0x1 0 0
		0xe000 0x0 0x0 0x4 &mpic 0x3 0x1 0 0>;

	pci_bridge@1c {
		interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
		interrupt-map = <

			/* IDSEL 0x00 (PrPMC Site) */
			0000 0x0 0x0 0x1 &mpic 0x0 0x1 0 0
			0000 0x0 0x0 0x2 &mpic 0x1 0x1 0 0
			0000 0x0 0x0 0x3 &mpic 0x2 0x1 0 0
			0000 0x0 0x0 0x4 &mpic 0x3 0x1 0 0

			/* IDSEL 0x04 (VIA chip) */
			0x2000 0x0 0x0 0x1 &mpic 0x0 0x1 0 0
			0x2000 0x0 0x0 0x2 &mpic 0x1 0x1 0 0
			0x2000 0x0 0x0 0x3 &mpic 0x2 0x1 0 0
			0x2000 0x0 0x0 0x4 &mpic 0x3 0x1 0 0

			/* IDSEL 0x05 (8139) */
			0x2800 0x0 0x0 0x1 &mpic 0x1 0x1 0 0

			/* IDSEL 0x06 (Slot 6) */
			0x3000 0x0 0x0 0x1 &mpic 0x2 0x1 0 0
			0x3000 0x0 0x0 0x2 &mpic 0x3 0x1 0 0
			0x3000 0x0 0x0 0x3 &mpic 0x0 0x1 0 0
			0x3000 0x0 0x0 0x4 &mpic 0x1 0x1 0 0

			/* IDESL 0x07 (Slot 7) */
			0x3800 0x0 0x0 0x1 &mpic 0x3 0x1 0 0
			0x3800 0x0 0x0 0x2 &mpic 0x0 0x1 0 0
			0x3800 0x0 0x0 0x3 &mpic 0x1 0x1 0 0
			0x3800 0x0 0x0 0x4 &mpic 0x2 0x1 0 0>;

		reg = <0xe000 0x0 0x0 0x0 0x0>;
		#interrupt-cells = <1>;
		#size-cells = <2>;
		#address-cells = <3>;
		ranges = <0x2000000 0x0 0x80000000
			  0x2000000 0x0 0x80000000
			  0x0 0x20000000
			  0x1000000 0x0 0x0
			  0x1000000 0x0 0x0
			  0x0 0x80000>;
		clock-frequency = <33333333>;

		isa@4 {
			device_type = "isa";
			#interrupt-cells = <2>;
			#size-cells = <1>;
			#address-cells = <2>;
			reg = <0x2000 0x0 0x0 0x0 0x0>;
			ranges = <0x1 0x0 0x1000000 0x0 0x0 0x1000>;
			interrupt-parent = <&i8259>;

			i8259: interrupt-controller@20 {
				interrupt-controller;
				device_type = "interrupt-controller";
				reg = <0x1 0x20 0x2
				       0x1 0xa0 0x2
				       0x1 0x4d0 0x2>;
				#address-cells = <0>;
				#interrupt-cells = <2>;
				compatible = "chrp,iic";
				interrupts = <0 1 0 0>;
				interrupt-parent = <&mpic>;
			};

			rtc@70 {
				compatible = "pnpPNP,b00";
				reg = <0x1 0x70 0x2>;
			};
		};
	};
};