blob: 30b7ec0cedb5e2765eb7ee03f808dd66a961f40a [file] [log] [blame]
Linus Torvalds1da177e2005-04-16 15:20:36 -07001/*
2 * mace.h - definitions for the registers in the Am79C940 MACE
3 * (Medium Access Control for Ethernet) controller.
4 *
5 * Copyright (C) 1996 Paul Mackerras.
6 *
7 * This program is free software; you can redistribute it and/or
8 * modify it under the terms of the GNU General Public License
9 * as published by the Free Software Foundation; either version
10 * 2 of the License, or (at your option) any later version.
11 */
12
13#define REG(x) volatile unsigned char x; char x ## _pad[15]
14
15struct mace {
16 REG(rcvfifo); /* receive FIFO */
17 REG(xmtfifo); /* transmit FIFO */
18 REG(xmtfc); /* transmit frame control */
19 REG(xmtfs); /* transmit frame status */
20 REG(xmtrc); /* transmit retry count */
21 REG(rcvfc); /* receive frame control */
22 REG(rcvfs); /* receive frame status (4 bytes) */
23 REG(fifofc); /* FIFO frame count */
24 REG(ir); /* interrupt register */
25 REG(imr); /* interrupt mask register */
26 REG(pr); /* poll register */
27 REG(biucc); /* bus interface unit config control */
28 REG(fifocc); /* FIFO configuration control */
29 REG(maccc); /* medium access control config control */
30 REG(plscc); /* phys layer signalling config control */
31 REG(phycc); /* physical configuration control */
32 REG(chipid_lo); /* chip ID, lsb */
33 REG(chipid_hi); /* chip ID, msb */
34 REG(iac); /* internal address config */
35 REG(reg19);
36 REG(ladrf); /* logical address filter (8 bytes) */
37 REG(padr); /* physical address (6 bytes) */
38 REG(reg22);
39 REG(reg23);
40 REG(mpc); /* missed packet count (clears when read) */
41 REG(reg25);
42 REG(rntpc); /* runt packet count (clears when read) */
43 REG(rcvcc); /* recv collision count (clears when read) */
44 REG(reg28);
45 REG(utr); /* user test reg */
46 REG(reg30);
47 REG(reg31);
48};
49
50/* Bits in XMTFC */
51#define DRTRY 0x80 /* don't retry transmission after collision */
52#define DXMTFCS 0x08 /* don't append FCS to transmitted frame */
53#define AUTO_PAD_XMIT 0x01 /* auto-pad short packets on transmission */
54
55/* Bits in XMTFS: only valid when XMTSV is set in PR and XMTFS */
56#define XMTSV 0x80 /* transmit status (i.e. XMTFS) valid */
57#define UFLO 0x40 /* underflow - xmit fifo ran dry */
58#define LCOL 0x20 /* late collision (transmission aborted) */
59#define MORE 0x10 /* 2 or more retries needed to xmit frame */
60#define ONE 0x08 /* 1 retry needed to xmit frame */
61#define DEFER 0x04 /* MACE had to defer xmission (enet busy) */
62#define LCAR 0x02 /* loss of carrier (transmission aborted) */
63#define RTRY 0x01 /* too many retries (transmission aborted) */
64
65/* Bits in XMTRC: only valid when XMTSV is set in PR (and XMTFS) */
66#define EXDEF 0x80 /* had to defer for excessive time */
67#define RETRY_MASK 0x0f /* number of retries (0 - 15) */
68
69/* Bits in RCVFC */
70#define LLRCV 0x08 /* low latency receive: early DMA request */
71#define M_RBAR 0x04 /* sets function of EAM/R pin */
72#define AUTO_STRIP_RCV 0x01 /* auto-strip short LLC frames on recv */
73
74/*
75 * Bits in RCVFS. After a frame is received, four bytes of status
76 * are automatically read from this register and appended to the frame
77 * data in memory. These are:
78 * Byte 0 and 1: message byte count and frame status
79 * Byte 2: runt packet count
80 * Byte 3: receive collision count
81 */
82#define RS_OFLO 0x8000 /* receive FIFO overflowed */
83#define RS_CLSN 0x4000 /* received frame suffered (late) collision */
84#define RS_FRAMERR 0x2000 /* framing error flag */
85#define RS_FCSERR 0x1000 /* frame had FCS error */
86#define RS_COUNT 0x0fff /* mask for byte count field */
87
88/* Bits (fields) in FIFOFC */
89#define RCVFC_SH 4 /* receive frame count in FIFO */
90#define RCVFC_MASK 0x0f
91#define XMTFC_SH 0 /* transmit frame count in FIFO */
92#define XMTFC_MASK 0x0f
93
94/*
95 * Bits in IR and IMR. The IR clears itself when read.
96 * Setting a bit in the IMR will disable the corresponding interrupt.
97 */
98#define JABBER 0x80 /* jabber error - 10baseT xmission too long */
99#define BABBLE 0x40 /* babble - xmitter xmitting for too long */
100#define CERR 0x20 /* collision err - no SQE test (heartbeat) */
101#define RCVCCO 0x10 /* RCVCC overflow */
102#define RNTPCO 0x08 /* RNTPC overflow */
103#define MPCO 0x04 /* MPC overflow */
104#define RCVINT 0x02 /* receive interrupt */
105#define XMTINT 0x01 /* transmitter interrupt */
106
107/* Bits in PR */
108#define XMTSV 0x80 /* XMTFS valid (same as in XMTFS) */
109#define TDTREQ 0x40 /* set when xmit fifo is requesting data */
110#define RDTREQ 0x20 /* set when recv fifo requests data xfer */
111
112/* Bits in BIUCC */
113#define BSWP 0x40 /* byte swap, i.e. big-endian bus */
114#define XMTSP_4 0x00 /* start xmitting when 4 bytes in FIFO */
115#define XMTSP_16 0x10 /* start xmitting when 16 bytes in FIFO */
116#define XMTSP_64 0x20 /* start xmitting when 64 bytes in FIFO */
117#define XMTSP_112 0x30 /* start xmitting when 112 bytes in FIFO */
118#define SWRST 0x01 /* software reset */
119
120/* Bits in FIFOCC */
121#define XMTFW_8 0x00 /* xmit fifo watermark = 8 words free */
122#define XMTFW_16 0x40 /* 16 words free */
123#define XMTFW_32 0x80 /* 32 words free */
124#define RCVFW_16 0x00 /* recv fifo watermark = 16 bytes avail */
125#define RCVFW_32 0x10 /* 32 bytes avail */
126#define RCVFW_64 0x20 /* 64 bytes avail */
127#define XMTFWU 0x08 /* xmit fifo watermark update enable */
128#define RCVFWU 0x04 /* recv fifo watermark update enable */
129#define XMTBRST 0x02 /* enable transmit burst mode */
130#define RCVBRST 0x01 /* enable receive burst mode */
131
132/* Bits in MACCC */
133#define PROM 0x80 /* promiscuous mode */
134#define DXMT2PD 0x40 /* disable xmit two-part deferral algorithm */
135#define EMBA 0x20 /* enable modified backoff algorithm */
136#define DRCVPA 0x08 /* disable receiving physical address */
137#define DRCVBC 0x04 /* disable receiving broadcasts */
138#define ENXMT 0x02 /* enable transmitter */
139#define ENRCV 0x01 /* enable receiver */
140
141/* Bits in PLSCC */
142#define XMTSEL 0x08 /* select DO+/DO- state when idle */
143#define PORTSEL_AUI 0x00 /* select AUI port */
144#define PORTSEL_10T 0x02 /* select 10Base-T port */
145#define PORTSEL_DAI 0x04 /* select DAI port */
146#define PORTSEL_GPSI 0x06 /* select GPSI port */
147#define ENPLSIO 0x01 /* enable optional PLS I/O pins */
148
149/* Bits in PHYCC */
150#define LNKFL 0x80 /* reports 10Base-T link failure */
151#define DLNKTST 0x40 /* disable 10Base-T link test */
152#define REVPOL 0x20 /* 10Base-T receiver polarity reversed */
153#define DAPC 0x10 /* disable auto receiver polarity correction */
154#define LRT 0x08 /* low receive threshold for long links */
155#define ASEL 0x04 /* auto-select AUI or 10Base-T port */
156#define RWAKE 0x02 /* remote wake function */
157#define AWAKE 0x01 /* auto wake function */
158
159/* Bits in IAC */
160#define ADDRCHG 0x80 /* request address change */
161#define PHYADDR 0x04 /* access physical address */
162#define LOGADDR 0x02 /* access multicast filter */
163
164/* Bits in UTR */
165#define RTRE 0x80 /* reserved test register enable. DON'T SET. */
166#define RTRD 0x40 /* reserved test register disable. Sticky */
167#define RPAC 0x20 /* accept runt packets */
168#define FCOLL 0x10 /* force collision */
169#define RCVFCSE 0x08 /* receive FCS enable */
170#define LOOP_NONE 0x00 /* no loopback */
171#define LOOP_EXT 0x02 /* external loopback */
172#define LOOP_INT 0x04 /* internal loopback, excludes MENDEC */
173#define LOOP_MENDEC 0x06 /* internal loopback, includes MENDEC */