blob: 3659dd7b9d760e9a0917a37e083ce3e84097e22d [file] [log] [blame]
Linus Torvalds1da177e2005-04-16 15:20:36 -07001/*
2 * Device driver for the SYMBIOS/LSILOGIC 53C8XX and 53C1010 family
3 * of PCI-SCSI IO processors.
4 *
5 * Copyright (C) 1999-2001 Gerard Roudier <groudier@free.fr>
6 *
7 * This driver is derived from the Linux sym53c8xx driver.
8 * Copyright (C) 1998-2000 Gerard Roudier
9 *
10 * The sym53c8xx driver is derived from the ncr53c8xx driver that had been
11 * a port of the FreeBSD ncr driver to Linux-1.2.13.
12 *
13 * The original ncr driver has been written for 386bsd and FreeBSD by
14 * Wolfgang Stanglmeier <wolf@cologne.de>
15 * Stefan Esser <se@mi.Uni-Koeln.de>
16 * Copyright (C) 1994 Wolfgang Stanglmeier
17 *
18 * Other major contributions:
19 *
20 * NVRAM detection and reading.
21 * Copyright (C) 1997 Richard Waltham <dormouse@farsrobt.demon.co.uk>
22 *
23 *-----------------------------------------------------------------------------
24 *
25 * This program is free software; you can redistribute it and/or modify
26 * it under the terms of the GNU General Public License as published by
27 * the Free Software Foundation; either version 2 of the License, or
28 * (at your option) any later version.
29 *
30 * This program is distributed in the hope that it will be useful,
31 * but WITHOUT ANY WARRANTY; without even the implied warranty of
32 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
33 * GNU General Public License for more details.
34 *
35 * You should have received a copy of the GNU General Public License
36 * along with this program; if not, write to the Free Software
37 * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
38 */
39
40#ifndef SYM_DEFS_H
41#define SYM_DEFS_H
42
Matthew Wilcoxad94c932005-11-29 23:08:48 -050043#define SYM_VERSION "2.2.2"
Linus Torvalds1da177e2005-04-16 15:20:36 -070044#define SYM_DRIVER_NAME "sym-" SYM_VERSION
45
46/*
47 * SYM53C8XX device features descriptor.
48 */
49struct sym_chip {
50 u_short device_id;
51 u_short revision_id;
52 char *name;
53 u_char burst_max; /* log-base-2 of max burst */
54 u_char offset_max;
55 u_char nr_divisor;
56 u_char lp_probe_bit;
57 u_int features;
58#define FE_LED0 (1<<0)
59#define FE_WIDE (1<<1) /* Wide data transfers */
60#define FE_ULTRA (1<<2) /* Ultra speed 20Mtrans/sec */
61#define FE_ULTRA2 (1<<3) /* Ultra 2 - 40 Mtrans/sec */
62#define FE_DBLR (1<<4) /* Clock doubler present */
63#define FE_QUAD (1<<5) /* Clock quadrupler present */
64#define FE_ERL (1<<6) /* Enable read line */
65#define FE_CLSE (1<<7) /* Cache line size enable */
66#define FE_WRIE (1<<8) /* Write & Invalidate enable */
67#define FE_ERMP (1<<9) /* Enable read multiple */
68#define FE_BOF (1<<10) /* Burst opcode fetch */
69#define FE_DFS (1<<11) /* DMA fifo size */
70#define FE_PFEN (1<<12) /* Prefetch enable */
71#define FE_LDSTR (1<<13) /* Load/Store supported */
72#define FE_RAM (1<<14) /* On chip RAM present */
73#define FE_VARCLK (1<<15) /* Clock frequency may vary */
74#define FE_RAM8K (1<<16) /* On chip RAM sized 8Kb */
75#define FE_64BIT (1<<17) /* 64-bit PCI BUS interface */
76#define FE_IO256 (1<<18) /* Requires full 256 bytes in PCI space */
77#define FE_NOPM (1<<19) /* Scripts handles phase mismatch */
78#define FE_LEDC (1<<20) /* Hardware control of LED */
79#define FE_ULTRA3 (1<<21) /* Ultra 3 - 80 Mtrans/sec DT */
80#define FE_66MHZ (1<<22) /* 66MHz PCI support */
81#define FE_CRC (1<<23) /* CRC support */
82#define FE_DIFF (1<<24) /* SCSI HVD support */
83#define FE_DFBC (1<<25) /* Have DFBC register */
84#define FE_LCKFRQ (1<<26) /* Have LCKFRQ */
85#define FE_C10 (1<<27) /* Various C10 core (mis)features */
86#define FE_U3EN (1<<28) /* U3EN bit usable */
87#define FE_DAC (1<<29) /* Support PCI DAC (64 bit addressing) */
88#define FE_ISTAT1 (1<<30) /* Have ISTAT1, MBOX0, MBOX1 registers */
89
90#define FE_CACHE_SET (FE_ERL|FE_CLSE|FE_WRIE|FE_ERMP)
91#define FE_CACHE0_SET (FE_CACHE_SET & ~FE_ERL)
92};
93
94/*
95 * SYM53C8XX IO register data structure.
96 */
97struct sym_reg {
98/*00*/ u8 nc_scntl0; /* full arb., ena parity, par->ATN */
99
100/*01*/ u8 nc_scntl1; /* no reset */
101 #define ISCON 0x10 /* connected to scsi */
102 #define CRST 0x08 /* force reset */
103 #define IARB 0x02 /* immediate arbitration */
104
105/*02*/ u8 nc_scntl2; /* no disconnect expected */
106 #define SDU 0x80 /* cmd: disconnect will raise error */
107 #define CHM 0x40 /* sta: chained mode */
108 #define WSS 0x08 /* sta: wide scsi send [W]*/
109 #define WSR 0x01 /* sta: wide scsi received [W]*/
110
111/*03*/ u8 nc_scntl3; /* cnf system clock dependent */
112 #define EWS 0x08 /* cmd: enable wide scsi [W]*/
113 #define ULTRA 0x80 /* cmd: ULTRA enable */
114 /* bits 0-2, 7 rsvd for C1010 */
115
116/*04*/ u8 nc_scid; /* cnf host adapter scsi address */
117 #define RRE 0x40 /* r/w:e enable response to resel. */
118 #define SRE 0x20 /* r/w:e enable response to select */
119
120/*05*/ u8 nc_sxfer; /* ### Sync speed and count */
121 /* bits 6-7 rsvd for C1010 */
122
123/*06*/ u8 nc_sdid; /* ### Destination-ID */
124
125/*07*/ u8 nc_gpreg; /* ??? IO-Pins */
126
127/*08*/ u8 nc_sfbr; /* ### First byte received */
128
129/*09*/ u8 nc_socl;
130 #define CREQ 0x80 /* r/w: SCSI-REQ */
131 #define CACK 0x40 /* r/w: SCSI-ACK */
132 #define CBSY 0x20 /* r/w: SCSI-BSY */
133 #define CSEL 0x10 /* r/w: SCSI-SEL */
134 #define CATN 0x08 /* r/w: SCSI-ATN */
135 #define CMSG 0x04 /* r/w: SCSI-MSG */
136 #define CC_D 0x02 /* r/w: SCSI-C_D */
137 #define CI_O 0x01 /* r/w: SCSI-I_O */
138
139/*0a*/ u8 nc_ssid;
140
141/*0b*/ u8 nc_sbcl;
142
143/*0c*/ u8 nc_dstat;
144 #define DFE 0x80 /* sta: dma fifo empty */
145 #define MDPE 0x40 /* int: master data parity error */
146 #define BF 0x20 /* int: script: bus fault */
147 #define ABRT 0x10 /* int: script: command aborted */
148 #define SSI 0x08 /* int: script: single step */
149 #define SIR 0x04 /* int: script: interrupt instruct. */
150 #define IID 0x01 /* int: script: illegal instruct. */
151
152/*0d*/ u8 nc_sstat0;
153 #define ILF 0x80 /* sta: data in SIDL register lsb */
154 #define ORF 0x40 /* sta: data in SODR register lsb */
155 #define OLF 0x20 /* sta: data in SODL register lsb */
156 #define AIP 0x10 /* sta: arbitration in progress */
157 #define LOA 0x08 /* sta: arbitration lost */
158 #define WOA 0x04 /* sta: arbitration won */
159 #define IRST 0x02 /* sta: scsi reset signal */
160 #define SDP 0x01 /* sta: scsi parity signal */
161
162/*0e*/ u8 nc_sstat1;
163 #define FF3210 0xf0 /* sta: bytes in the scsi fifo */
164
165/*0f*/ u8 nc_sstat2;
166 #define ILF1 0x80 /* sta: data in SIDL register msb[W]*/
167 #define ORF1 0x40 /* sta: data in SODR register msb[W]*/
168 #define OLF1 0x20 /* sta: data in SODL register msb[W]*/
169 #define DM 0x04 /* sta: DIFFSENS mismatch (895/6 only) */
170 #define LDSC 0x02 /* sta: disconnect & reconnect */
171
172/*10*/ u8 nc_dsa; /* --> Base page */
173/*11*/ u8 nc_dsa1;
174/*12*/ u8 nc_dsa2;
175/*13*/ u8 nc_dsa3;
176
177/*14*/ u8 nc_istat; /* --> Main Command and status */
178 #define CABRT 0x80 /* cmd: abort current operation */
179 #define SRST 0x40 /* mod: reset chip */
180 #define SIGP 0x20 /* r/w: message from host to script */
181 #define SEM 0x10 /* r/w: message between host + script */
182 #define CON 0x08 /* sta: connected to scsi */
183 #define INTF 0x04 /* sta: int on the fly (reset by wr)*/
184 #define SIP 0x02 /* sta: scsi-interrupt */
185 #define DIP 0x01 /* sta: host/script interrupt */
186
187/*15*/ u8 nc_istat1; /* 896 only */
188 #define FLSH 0x04 /* sta: chip is flushing */
189 #define SCRUN 0x02 /* sta: scripts are running */
190 #define SIRQD 0x01 /* r/w: disable INT pin */
191
192/*16*/ u8 nc_mbox0; /* 896 only */
193/*17*/ u8 nc_mbox1; /* 896 only */
194
195/*18*/ u8 nc_ctest0;
196/*19*/ u8 nc_ctest1;
197
198/*1a*/ u8 nc_ctest2;
199 #define CSIGP 0x40
200 /* bits 0-2,7 rsvd for C1010 */
201
202/*1b*/ u8 nc_ctest3;
203 #define FLF 0x08 /* cmd: flush dma fifo */
204 #define CLF 0x04 /* cmd: clear dma fifo */
205 #define FM 0x02 /* mod: fetch pin mode */
206 #define WRIE 0x01 /* mod: write and invalidate enable */
207 /* bits 4-7 rsvd for C1010 */
208
209/*1c*/ u32 nc_temp; /* ### Temporary stack */
210
211/*20*/ u8 nc_dfifo;
212/*21*/ u8 nc_ctest4;
213 #define BDIS 0x80 /* mod: burst disable */
214 #define MPEE 0x08 /* mod: master parity error enable */
215
216/*22*/ u8 nc_ctest5;
217 #define DFS 0x20 /* mod: dma fifo size */
218 /* bits 0-1, 3-7 rsvd for C1010 */
219
220/*23*/ u8 nc_ctest6;
221
222/*24*/ u32 nc_dbc; /* ### Byte count and command */
223/*28*/ u32 nc_dnad; /* ### Next command register */
224/*2c*/ u32 nc_dsp; /* --> Script Pointer */
225/*30*/ u32 nc_dsps; /* --> Script pointer save/opcode#2 */
226
227/*34*/ u8 nc_scratcha; /* Temporary register a */
228/*35*/ u8 nc_scratcha1;
229/*36*/ u8 nc_scratcha2;
230/*37*/ u8 nc_scratcha3;
231
232/*38*/ u8 nc_dmode;
233 #define BL_2 0x80 /* mod: burst length shift value +2 */
234 #define BL_1 0x40 /* mod: burst length shift value +1 */
235 #define ERL 0x08 /* mod: enable read line */
236 #define ERMP 0x04 /* mod: enable read multiple */
237 #define BOF 0x02 /* mod: burst op code fetch */
238
239/*39*/ u8 nc_dien;
240/*3a*/ u8 nc_sbr;
241
242/*3b*/ u8 nc_dcntl; /* --> Script execution control */
243 #define CLSE 0x80 /* mod: cache line size enable */
244 #define PFF 0x40 /* cmd: pre-fetch flush */
245 #define PFEN 0x20 /* mod: pre-fetch enable */
246 #define SSM 0x10 /* mod: single step mode */
247 #define IRQM 0x08 /* mod: irq mode (1 = totem pole !) */
248 #define STD 0x04 /* cmd: start dma mode */
249 #define IRQD 0x02 /* mod: irq disable */
250 #define NOCOM 0x01 /* cmd: protect sfbr while reselect */
251 /* bits 0-1 rsvd for C1010 */
252
253/*3c*/ u32 nc_adder;
254
255/*40*/ u16 nc_sien; /* -->: interrupt enable */
256/*42*/ u16 nc_sist; /* <--: interrupt status */
257 #define SBMC 0x1000/* sta: SCSI Bus Mode Change (895/6 only) */
258 #define STO 0x0400/* sta: timeout (select) */
259 #define GEN 0x0200/* sta: timeout (general) */
260 #define HTH 0x0100/* sta: timeout (handshake) */
261 #define MA 0x80 /* sta: phase mismatch */
262 #define CMP 0x40 /* sta: arbitration complete */
263 #define SEL 0x20 /* sta: selected by another device */
264 #define RSL 0x10 /* sta: reselected by another device*/
265 #define SGE 0x08 /* sta: gross error (over/underflow)*/
266 #define UDC 0x04 /* sta: unexpected disconnect */
267 #define RST 0x02 /* sta: scsi bus reset detected */
268 #define PAR 0x01 /* sta: scsi parity error */
269
270/*44*/ u8 nc_slpar;
271/*45*/ u8 nc_swide;
272/*46*/ u8 nc_macntl;
273/*47*/ u8 nc_gpcntl;
274/*48*/ u8 nc_stime0; /* cmd: timeout for select&handshake*/
275/*49*/ u8 nc_stime1; /* cmd: timeout user defined */
276/*4a*/ u16 nc_respid; /* sta: Reselect-IDs */
277
278/*4c*/ u8 nc_stest0;
279
280/*4d*/ u8 nc_stest1;
281 #define SCLK 0x80 /* Use the PCI clock as SCSI clock */
282 #define DBLEN 0x08 /* clock doubler running */
283 #define DBLSEL 0x04 /* clock doubler selected */
284
285
286/*4e*/ u8 nc_stest2;
287 #define ROF 0x40 /* reset scsi offset (after gross error!) */
288 #define EXT 0x02 /* extended filtering */
289
290/*4f*/ u8 nc_stest3;
291 #define TE 0x80 /* c: tolerAnt enable */
292 #define HSC 0x20 /* c: Halt SCSI Clock */
293 #define CSF 0x02 /* c: clear scsi fifo */
294
295/*50*/ u16 nc_sidl; /* Lowlevel: latched from scsi data */
296/*52*/ u8 nc_stest4;
297 #define SMODE 0xc0 /* SCSI bus mode (895/6 only) */
298 #define SMODE_HVD 0x40 /* High Voltage Differential */
299 #define SMODE_SE 0x80 /* Single Ended */
300 #define SMODE_LVD 0xc0 /* Low Voltage Differential */
301 #define LCKFRQ 0x20 /* Frequency Lock (895/6 only) */
302 /* bits 0-5 rsvd for C1010 */
303
304/*53*/ u8 nc_53_;
305/*54*/ u16 nc_sodl; /* Lowlevel: data out to scsi data */
306/*56*/ u8 nc_ccntl0; /* Chip Control 0 (896) */
307 #define ENPMJ 0x80 /* Enable Phase Mismatch Jump */
308 #define PMJCTL 0x40 /* Phase Mismatch Jump Control */
309 #define ENNDJ 0x20 /* Enable Non Data PM Jump */
310 #define DISFC 0x10 /* Disable Auto FIFO Clear */
311 #define DILS 0x02 /* Disable Internal Load/Store */
312 #define DPR 0x01 /* Disable Pipe Req */
313
314/*57*/ u8 nc_ccntl1; /* Chip Control 1 (896) */
315 #define ZMOD 0x80 /* High Impedance Mode */
316 #define DDAC 0x08 /* Disable Dual Address Cycle */
317 #define XTIMOD 0x04 /* 64-bit Table Ind. Indexing Mode */
318 #define EXTIBMV 0x02 /* Enable 64-bit Table Ind. BMOV */
319 #define EXDBMV 0x01 /* Enable 64-bit Direct BMOV */
320
321/*58*/ u16 nc_sbdl; /* Lowlevel: data from scsi data */
322/*5a*/ u16 nc_5a_;
323
324/*5c*/ u8 nc_scr0; /* Working register B */
325/*5d*/ u8 nc_scr1;
326/*5e*/ u8 nc_scr2;
327/*5f*/ u8 nc_scr3;
328
329/*60*/ u8 nc_scrx[64]; /* Working register C-R */
330/*a0*/ u32 nc_mmrs; /* Memory Move Read Selector */
331/*a4*/ u32 nc_mmws; /* Memory Move Write Selector */
332/*a8*/ u32 nc_sfs; /* Script Fetch Selector */
333/*ac*/ u32 nc_drs; /* DSA Relative Selector */
334/*b0*/ u32 nc_sbms; /* Static Block Move Selector */
335/*b4*/ u32 nc_dbms; /* Dynamic Block Move Selector */
336/*b8*/ u32 nc_dnad64; /* DMA Next Address 64 */
337/*bc*/ u16 nc_scntl4; /* C1010 only */
338 #define U3EN 0x80 /* Enable Ultra 3 */
339 #define AIPCKEN 0x40 /* AIP checking enable */
340 /* Also enable AIP generation on C10-33*/
341 #define XCLKH_DT 0x08 /* Extra clock of data hold on DT edge */
342 #define XCLKH_ST 0x04 /* Extra clock of data hold on ST edge */
343 #define XCLKS_DT 0x02 /* Extra clock of data set on DT edge */
344 #define XCLKS_ST 0x01 /* Extra clock of data set on ST edge */
345/*be*/ u8 nc_aipcntl0; /* AIP Control 0 C1010 only */
346/*bf*/ u8 nc_aipcntl1; /* AIP Control 1 C1010 only */
347 #define DISAIP 0x08 /* Disable AIP generation C10-66 only */
348/*c0*/ u32 nc_pmjad1; /* Phase Mismatch Jump Address 1 */
349/*c4*/ u32 nc_pmjad2; /* Phase Mismatch Jump Address 2 */
350/*c8*/ u8 nc_rbc; /* Remaining Byte Count */
351/*c9*/ u8 nc_rbc1;
352/*ca*/ u8 nc_rbc2;
353/*cb*/ u8 nc_rbc3;
354
355/*cc*/ u8 nc_ua; /* Updated Address */
356/*cd*/ u8 nc_ua1;
357/*ce*/ u8 nc_ua2;
358/*cf*/ u8 nc_ua3;
359/*d0*/ u32 nc_esa; /* Entry Storage Address */
360/*d4*/ u8 nc_ia; /* Instruction Address */
361/*d5*/ u8 nc_ia1;
362/*d6*/ u8 nc_ia2;
363/*d7*/ u8 nc_ia3;
364/*d8*/ u32 nc_sbc; /* SCSI Byte Count (3 bytes only) */
365/*dc*/ u32 nc_csbc; /* Cumulative SCSI Byte Count */
366 /* Following for C1010 only */
367/*e0*/ u16 nc_crcpad; /* CRC Value */
368/*e2*/ u8 nc_crccntl0; /* CRC control register */
369 #define SNDCRC 0x10 /* Send CRC Request */
370/*e3*/ u8 nc_crccntl1; /* CRC control register */
371/*e4*/ u32 nc_crcdata; /* CRC data register */
372/*e8*/ u32 nc_e8_;
373/*ec*/ u32 nc_ec_;
374/*f0*/ u16 nc_dfbc; /* DMA FIFO byte count */
375};
376
377/*-----------------------------------------------------------
378 *
379 * Utility macros for the script.
380 *
381 *-----------------------------------------------------------
382 */
383
384#define REGJ(p,r) (offsetof(struct sym_reg, p ## r))
385#define REG(r) REGJ (nc_, r)
386
387/*-----------------------------------------------------------
388 *
389 * SCSI phases
390 *
391 *-----------------------------------------------------------
392 */
393
394#define SCR_DATA_OUT 0x00000000
395#define SCR_DATA_IN 0x01000000
396#define SCR_COMMAND 0x02000000
397#define SCR_STATUS 0x03000000
398#define SCR_DT_DATA_OUT 0x04000000
399#define SCR_DT_DATA_IN 0x05000000
400#define SCR_MSG_OUT 0x06000000
401#define SCR_MSG_IN 0x07000000
402/* DT phases are illegal for non Ultra3 mode */
403#define SCR_ILG_OUT 0x04000000
404#define SCR_ILG_IN 0x05000000
405
406/*-----------------------------------------------------------
407 *
408 * Data transfer via SCSI.
409 *
410 *-----------------------------------------------------------
411 *
412 * MOVE_ABS (LEN)
413 * <<start address>>
414 *
415 * MOVE_IND (LEN)
416 * <<dnad_offset>>
417 *
418 * MOVE_TBL
419 * <<dnad_offset>>
420 *
421 *-----------------------------------------------------------
422 */
423
424#define OPC_MOVE 0x08000000
425
426#define SCR_MOVE_ABS(l) ((0x00000000 | OPC_MOVE) | (l))
427/* #define SCR_MOVE_IND(l) ((0x20000000 | OPC_MOVE) | (l)) */
428#define SCR_MOVE_TBL (0x10000000 | OPC_MOVE)
429
430#define SCR_CHMOV_ABS(l) ((0x00000000) | (l))
431/* #define SCR_CHMOV_IND(l) ((0x20000000) | (l)) */
432#define SCR_CHMOV_TBL (0x10000000)
433
434#ifdef SYM_CONF_TARGET_ROLE_SUPPORT
435/* We steal the `indirect addressing' flag for target mode MOVE in scripts */
436
437#define OPC_TCHMOVE 0x08000000
438
439#define SCR_TCHMOVE_ABS(l) ((0x20000000 | OPC_TCHMOVE) | (l))
440#define SCR_TCHMOVE_TBL (0x30000000 | OPC_TCHMOVE)
441
442#define SCR_TMOV_ABS(l) ((0x20000000) | (l))
443#define SCR_TMOV_TBL (0x30000000)
444#endif
445
446struct sym_tblmove {
447 u32 size;
448 u32 addr;
449};
450
451/*-----------------------------------------------------------
452 *
453 * Selection
454 *
455 *-----------------------------------------------------------
456 *
457 * SEL_ABS | SCR_ID (0..15) [ | REL_JMP]
458 * <<alternate_address>>
459 *
460 * SEL_TBL | << dnad_offset>> [ | REL_JMP]
461 * <<alternate_address>>
462 *
463 *-----------------------------------------------------------
464 */
465
466#define SCR_SEL_ABS 0x40000000
467#define SCR_SEL_ABS_ATN 0x41000000
468#define SCR_SEL_TBL 0x42000000
469#define SCR_SEL_TBL_ATN 0x43000000
470
471#ifdef SYM_CONF_TARGET_ROLE_SUPPORT
472#define SCR_RESEL_ABS 0x40000000
473#define SCR_RESEL_ABS_ATN 0x41000000
474#define SCR_RESEL_TBL 0x42000000
475#define SCR_RESEL_TBL_ATN 0x43000000
476#endif
477
478struct sym_tblsel {
479 u_char sel_scntl4; /* C1010 only */
480 u_char sel_sxfer;
481 u_char sel_id;
482 u_char sel_scntl3;
483};
484
485#define SCR_JMP_REL 0x04000000
486#define SCR_ID(id) (((u32)(id)) << 16)
487
488/*-----------------------------------------------------------
489 *
490 * Waiting for Disconnect or Reselect
491 *
492 *-----------------------------------------------------------
493 *
494 * WAIT_DISC
495 * dummy: <<alternate_address>>
496 *
497 * WAIT_RESEL
498 * <<alternate_address>>
499 *
500 *-----------------------------------------------------------
501 */
502
503#define SCR_WAIT_DISC 0x48000000
504#define SCR_WAIT_RESEL 0x50000000
505
506#ifdef SYM_CONF_TARGET_ROLE_SUPPORT
507#define SCR_DISCONNECT 0x48000000
508#endif
509
510/*-----------------------------------------------------------
511 *
512 * Bit Set / Reset
513 *
514 *-----------------------------------------------------------
515 *
516 * SET (flags {|.. })
517 *
518 * CLR (flags {|.. })
519 *
520 *-----------------------------------------------------------
521 */
522
523#define SCR_SET(f) (0x58000000 | (f))
524#define SCR_CLR(f) (0x60000000 | (f))
525
526#define SCR_CARRY 0x00000400
527#define SCR_TRG 0x00000200
528#define SCR_ACK 0x00000040
529#define SCR_ATN 0x00000008
530
531
532/*-----------------------------------------------------------
533 *
534 * Memory to memory move
535 *
536 *-----------------------------------------------------------
537 *
538 * COPY (bytecount)
539 * << source_address >>
540 * << destination_address >>
541 *
542 * SCR_COPY sets the NO FLUSH option by default.
543 * SCR_COPY_F does not set this option.
544 *
545 * For chips which do not support this option,
546 * sym_fw_bind_script() will remove this bit.
547 *
548 *-----------------------------------------------------------
549 */
550
551#define SCR_NO_FLUSH 0x01000000
552
553#define SCR_COPY(n) (0xc0000000 | SCR_NO_FLUSH | (n))
554#define SCR_COPY_F(n) (0xc0000000 | (n))
555
556/*-----------------------------------------------------------
557 *
558 * Register move and binary operations
559 *
560 *-----------------------------------------------------------
561 *
562 * SFBR_REG (reg, op, data) reg = SFBR op data
563 * << 0 >>
564 *
565 * REG_SFBR (reg, op, data) SFBR = reg op data
566 * << 0 >>
567 *
568 * REG_REG (reg, op, data) reg = reg op data
569 * << 0 >>
570 *
571 *-----------------------------------------------------------
572 *
573 * On 825A, 875, 895 and 896 chips the content
574 * of SFBR register can be used as data (SCR_SFBR_DATA).
575 * The 896 has additionnal IO registers starting at
576 * offset 0x80. Bit 7 of register offset is stored in
577 * bit 7 of the SCRIPTS instruction first DWORD.
578 *
579 *-----------------------------------------------------------
580 */
581
582#define SCR_REG_OFS(ofs) ((((ofs) & 0x7f) << 16ul) + ((ofs) & 0x80))
583
584#define SCR_SFBR_REG(reg,op,data) \
585 (0x68000000 | (SCR_REG_OFS(REG(reg))) | (op) | (((data)&0xff)<<8ul))
586
587#define SCR_REG_SFBR(reg,op,data) \
588 (0x70000000 | (SCR_REG_OFS(REG(reg))) | (op) | (((data)&0xff)<<8ul))
589
590#define SCR_REG_REG(reg,op,data) \
591 (0x78000000 | (SCR_REG_OFS(REG(reg))) | (op) | (((data)&0xff)<<8ul))
592
593
594#define SCR_LOAD 0x00000000
595#define SCR_SHL 0x01000000
596#define SCR_OR 0x02000000
597#define SCR_XOR 0x03000000
598#define SCR_AND 0x04000000
599#define SCR_SHR 0x05000000
600#define SCR_ADD 0x06000000
601#define SCR_ADDC 0x07000000
602
603#define SCR_SFBR_DATA (0x00800000>>8ul) /* Use SFBR as data */
604
605/*-----------------------------------------------------------
606 *
607 * FROM_REG (reg) SFBR = reg
608 * << 0 >>
609 *
610 * TO_REG (reg) reg = SFBR
611 * << 0 >>
612 *
613 * LOAD_REG (reg, data) reg = <data>
614 * << 0 >>
615 *
616 * LOAD_SFBR(data) SFBR = <data>
617 * << 0 >>
618 *
619 *-----------------------------------------------------------
620 */
621
622#define SCR_FROM_REG(reg) \
623 SCR_REG_SFBR(reg,SCR_OR,0)
624
625#define SCR_TO_REG(reg) \
626 SCR_SFBR_REG(reg,SCR_OR,0)
627
628#define SCR_LOAD_REG(reg,data) \
629 SCR_REG_REG(reg,SCR_LOAD,data)
630
631#define SCR_LOAD_SFBR(data) \
632 (SCR_REG_SFBR (gpreg, SCR_LOAD, data))
633
634/*-----------------------------------------------------------
635 *
636 * LOAD from memory to register.
637 * STORE from register to memory.
638 *
639 * Only supported by 810A, 860, 825A, 875, 895 and 896.
640 *
641 *-----------------------------------------------------------
642 *
643 * LOAD_ABS (LEN)
644 * <<start address>>
645 *
646 * LOAD_REL (LEN) (DSA relative)
647 * <<dsa_offset>>
648 *
649 *-----------------------------------------------------------
650 */
651
652#define SCR_REG_OFS2(ofs) (((ofs) & 0xff) << 16ul)
653#define SCR_NO_FLUSH2 0x02000000
654#define SCR_DSA_REL2 0x10000000
655
656#define SCR_LOAD_R(reg, how, n) \
657 (0xe1000000 | how | (SCR_REG_OFS2(REG(reg))) | (n))
658
659#define SCR_STORE_R(reg, how, n) \
660 (0xe0000000 | how | (SCR_REG_OFS2(REG(reg))) | (n))
661
662#define SCR_LOAD_ABS(reg, n) SCR_LOAD_R(reg, SCR_NO_FLUSH2, n)
663#define SCR_LOAD_REL(reg, n) SCR_LOAD_R(reg, SCR_NO_FLUSH2|SCR_DSA_REL2, n)
664#define SCR_LOAD_ABS_F(reg, n) SCR_LOAD_R(reg, 0, n)
665#define SCR_LOAD_REL_F(reg, n) SCR_LOAD_R(reg, SCR_DSA_REL2, n)
666
667#define SCR_STORE_ABS(reg, n) SCR_STORE_R(reg, SCR_NO_FLUSH2, n)
668#define SCR_STORE_REL(reg, n) SCR_STORE_R(reg, SCR_NO_FLUSH2|SCR_DSA_REL2,n)
669#define SCR_STORE_ABS_F(reg, n) SCR_STORE_R(reg, 0, n)
670#define SCR_STORE_REL_F(reg, n) SCR_STORE_R(reg, SCR_DSA_REL2, n)
671
672
673/*-----------------------------------------------------------
674 *
675 * Waiting for Disconnect or Reselect
676 *
677 *-----------------------------------------------------------
678 *
679 * JUMP [ | IFTRUE/IFFALSE ( ... ) ]
680 * <<address>>
681 *
682 * JUMPR [ | IFTRUE/IFFALSE ( ... ) ]
683 * <<distance>>
684 *
685 * CALL [ | IFTRUE/IFFALSE ( ... ) ]
686 * <<address>>
687 *
688 * CALLR [ | IFTRUE/IFFALSE ( ... ) ]
689 * <<distance>>
690 *
691 * RETURN [ | IFTRUE/IFFALSE ( ... ) ]
692 * <<dummy>>
693 *
694 * INT [ | IFTRUE/IFFALSE ( ... ) ]
695 * <<ident>>
696 *
697 * INT_FLY [ | IFTRUE/IFFALSE ( ... ) ]
698 * <<ident>>
699 *
700 * Conditions:
701 * WHEN (phase)
702 * IF (phase)
703 * CARRYSET
704 * DATA (data, mask)
705 *
706 *-----------------------------------------------------------
707 */
708
709#define SCR_NO_OP 0x80000000
710#define SCR_JUMP 0x80080000
711#define SCR_JUMP64 0x80480000
712#define SCR_JUMPR 0x80880000
713#define SCR_CALL 0x88080000
714#define SCR_CALLR 0x88880000
715#define SCR_RETURN 0x90080000
716#define SCR_INT 0x98080000
717#define SCR_INT_FLY 0x98180000
718
719#define IFFALSE(arg) (0x00080000 | (arg))
720#define IFTRUE(arg) (0x00000000 | (arg))
721
722#define WHEN(phase) (0x00030000 | (phase))
723#define IF(phase) (0x00020000 | (phase))
724
725#define DATA(D) (0x00040000 | ((D) & 0xff))
726#define MASK(D,M) (0x00040000 | (((M ^ 0xff) & 0xff) << 8ul)|((D) & 0xff))
727
728#define CARRYSET (0x00200000)
729
730/*-----------------------------------------------------------
731 *
732 * SCSI constants.
733 *
734 *-----------------------------------------------------------
735 */
736
737/*
738 * Messages
739 */
740
741#define M_COMPLETE COMMAND_COMPLETE
742#define M_EXTENDED EXTENDED_MESSAGE
743#define M_SAVE_DP SAVE_POINTERS
744#define M_RESTORE_DP RESTORE_POINTERS
745#define M_DISCONNECT DISCONNECT
746#define M_ID_ERROR INITIATOR_ERROR
747#define M_ABORT ABORT_TASK_SET
748#define M_REJECT MESSAGE_REJECT
749#define M_NOOP NOP
750#define M_PARITY MSG_PARITY_ERROR
751#define M_LCOMPLETE LINKED_CMD_COMPLETE
752#define M_FCOMPLETE LINKED_FLG_CMD_COMPLETE
753#define M_RESET TARGET_RESET
754#define M_ABORT_TAG ABORT_TASK
755#define M_CLEAR_QUEUE CLEAR_TASK_SET
756#define M_INIT_REC INITIATE_RECOVERY
757#define M_REL_REC RELEASE_RECOVERY
758#define M_TERMINATE (0x11)
759#define M_SIMPLE_TAG SIMPLE_QUEUE_TAG
760#define M_HEAD_TAG HEAD_OF_QUEUE_TAG
761#define M_ORDERED_TAG ORDERED_QUEUE_TAG
762#define M_IGN_RESIDUE IGNORE_WIDE_RESIDUE
763
764#define M_X_MODIFY_DP EXTENDED_MODIFY_DATA_POINTER
765#define M_X_SYNC_REQ EXTENDED_SDTR
766#define M_X_WIDE_REQ EXTENDED_WDTR
767#define M_X_PPR_REQ EXTENDED_PPR
768
769/*
770 * PPR protocol options
771 */
772#define PPR_OPT_IU (0x01)
773#define PPR_OPT_DT (0x02)
774#define PPR_OPT_QAS (0x04)
775#define PPR_OPT_MASK (0x07)
776
777/*
778 * Status
779 */
780
781#define S_GOOD SAM_STAT_GOOD
782#define S_CHECK_COND SAM_STAT_CHECK_CONDITION
783#define S_COND_MET SAM_STAT_CONDITION_MET
784#define S_BUSY SAM_STAT_BUSY
785#define S_INT SAM_STAT_INTERMEDIATE
786#define S_INT_COND_MET SAM_STAT_INTERMEDIATE_CONDITION_MET
787#define S_CONFLICT SAM_STAT_RESERVATION_CONFLICT
788#define S_TERMINATED SAM_STAT_COMMAND_TERMINATED
789#define S_QUEUE_FULL SAM_STAT_TASK_SET_FULL
790#define S_ILLEGAL (0xff)
791
792#endif /* defined SYM_DEFS_H */