Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1 | # |
| 2 | # USB Gadget support on a system involves |
| 3 | # (a) a peripheral controller, and |
| 4 | # (b) the gadget driver using it. |
| 5 | # |
| 6 | # NOTE: Gadget support ** DOES NOT ** depend on host-side CONFIG_USB !! |
| 7 | # |
| 8 | # - Host systems (like PCs) need CONFIG_USB (with "A" jacks). |
| 9 | # - Peripherals (like PDAs) need CONFIG_USB_GADGET (with "B" jacks). |
Matt LaPlante | cab0089 | 2006-10-03 22:36:44 +0200 | [diff] [blame] | 10 | # - Some systems have both kinds of controllers. |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 11 | # |
| 12 | # With help from a special transceiver and a "Mini-AB" jack, systems with |
| 13 | # both kinds of controller can also support "USB On-the-Go" (CONFIG_USB_OTG). |
| 14 | # |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 15 | |
Denis Cheng | b75be4a | 2008-01-24 16:36:31 +0800 | [diff] [blame] | 16 | menuconfig USB_GADGET |
| 17 | tristate "USB Gadget Support" |
Alan Stern | 86dc243 | 2011-11-17 16:42:24 -0500 | [diff] [blame] | 18 | select NLS |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 19 | help |
| 20 | USB is a master/slave protocol, organized with one master |
| 21 | host (such as a PC) controlling up to 127 peripheral devices. |
| 22 | The USB hardware is asymmetric, which makes it easier to set up: |
| 23 | you can't connect a "to-the-host" connector to a peripheral. |
| 24 | |
| 25 | Linux can run in the host, or in the peripheral. In both cases |
| 26 | you need a low level bus controller driver, and some software |
| 27 | talking to it. Peripheral controllers are often discrete silicon, |
| 28 | or are integrated with the CPU in a microcontroller. The more |
Jules Villard | e113f29 | 2006-08-22 22:40:15 +0200 | [diff] [blame] | 29 | familiar host side controllers have names like "EHCI", "OHCI", |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 30 | or "UHCI", and are usually integrated into southbridges on PC |
| 31 | motherboards. |
| 32 | |
| 33 | Enable this configuration option if you want to run Linux inside |
| 34 | a USB peripheral device. Configure one hardware driver for your |
| 35 | peripheral/device side bus controller, and a "gadget driver" for |
| 36 | your peripheral protocol. (If you use modular gadget drivers, |
| 37 | you may configure more than one.) |
| 38 | |
| 39 | If in doubt, say "N" and don't enable these drivers; most people |
| 40 | don't have this kind of hardware (except maybe inside Linux PDAs). |
| 41 | |
| 42 | For more information, see <http://www.linux-usb.org/gadget> and |
| 43 | the kernel DocBook documentation for this API. |
| 44 | |
Denis Cheng | b75be4a | 2008-01-24 16:36:31 +0800 | [diff] [blame] | 45 | if USB_GADGET |
| 46 | |
David Brownell | 70790f6 | 2007-07-01 17:35:28 -0700 | [diff] [blame] | 47 | config USB_GADGET_DEBUG |
Robert P. J. Day | afd0e0f | 2008-03-10 15:09:51 -0400 | [diff] [blame] | 48 | boolean "Debugging messages (DEVELOPMENT)" |
David Brownell | 36e893d | 2008-09-12 09:39:06 -0700 | [diff] [blame] | 49 | depends on DEBUG_KERNEL |
David Brownell | 70790f6 | 2007-07-01 17:35:28 -0700 | [diff] [blame] | 50 | help |
| 51 | Many controller and gadget drivers will print some debugging |
| 52 | messages if you use this option to ask for those messages. |
| 53 | |
| 54 | Avoid enabling these messages, even if you're actively |
| 55 | debugging such a driver. Many drivers will emit so many |
| 56 | messages that the driver timings are affected, which will |
| 57 | either create new failure modes or remove the one you're |
| 58 | trying to track down. Never enable these messages for a |
| 59 | production build. |
| 60 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 61 | config USB_GADGET_DEBUG_FILES |
Robert P. J. Day | afd0e0f | 2008-03-10 15:09:51 -0400 | [diff] [blame] | 62 | boolean "Debugging information files (DEVELOPMENT)" |
David Brownell | 36e893d | 2008-09-12 09:39:06 -0700 | [diff] [blame] | 63 | depends on PROC_FS |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 64 | help |
| 65 | Some of the drivers in the "gadget" framework can expose |
| 66 | debugging information in files such as /proc/driver/udc |
| 67 | (for a peripheral controller). The information in these |
| 68 | files may help when you're troubleshooting or bringing up a |
| 69 | driver on a new board. Enable these files by choosing "Y" |
| 70 | here. If in doubt, or to conserve kernel memory, say "N". |
| 71 | |
Haavard Skinnemoen | 914a3f3 | 2007-10-10 02:29:43 -0700 | [diff] [blame] | 72 | config USB_GADGET_DEBUG_FS |
Robert P. J. Day | afd0e0f | 2008-03-10 15:09:51 -0400 | [diff] [blame] | 73 | boolean "Debugging information files in debugfs (DEVELOPMENT)" |
David Brownell | 36e893d | 2008-09-12 09:39:06 -0700 | [diff] [blame] | 74 | depends on DEBUG_FS |
Haavard Skinnemoen | 914a3f3 | 2007-10-10 02:29:43 -0700 | [diff] [blame] | 75 | help |
| 76 | Some of the drivers in the "gadget" framework can expose |
| 77 | debugging information in files under /sys/kernel/debug/. |
| 78 | The information in these files may help when you're |
| 79 | troubleshooting or bringing up a driver on a new board. |
| 80 | Enable these files by choosing "Y" here. If in doubt, or |
| 81 | to conserve kernel memory, say "N". |
| 82 | |
David Brownell | 36e893d | 2008-09-12 09:39:06 -0700 | [diff] [blame] | 83 | config USB_GADGET_VBUS_DRAW |
| 84 | int "Maximum VBUS Power usage (2-500 mA)" |
| 85 | range 2 500 |
| 86 | default 2 |
| 87 | help |
| 88 | Some devices need to draw power from USB when they are |
| 89 | configured, perhaps to operate circuitry or to recharge |
| 90 | batteries. This is in addition to any local power supply, |
| 91 | such as an AC adapter or batteries. |
| 92 | |
| 93 | Enter the maximum power your device draws through USB, in |
| 94 | milliAmperes. The permitted range of values is 2 - 500 mA; |
| 95 | 0 mA would be legal, but can make some hosts misbehave. |
| 96 | |
| 97 | This value will be used except for system-specific gadget |
| 98 | drivers that have more specific information. |
| 99 | |
Per Forlin | 6532c7f | 2011-08-19 21:21:27 +0200 | [diff] [blame] | 100 | config USB_GADGET_STORAGE_NUM_BUFFERS |
| 101 | int "Number of storage pipeline buffers" |
| 102 | range 2 4 |
| 103 | default 2 |
| 104 | help |
| 105 | Usually 2 buffers are enough to establish a good buffering |
| 106 | pipeline. The number may be increased in order to compensate |
| 107 | for a bursty VFS behaviour. For instance there may be CPU wake up |
| 108 | latencies that makes the VFS to appear bursty in a system with |
| 109 | an CPU on-demand governor. Especially if DMA is doing IO to |
| 110 | offload the CPU. In this case the CPU will go into power |
| 111 | save often and spin up occasionally to move data within VFS. |
| 112 | If selecting USB_GADGET_DEBUG_FILES this value may be set by |
| 113 | a module parameter as well. |
| 114 | If unsure, say 2. |
| 115 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 116 | # |
| 117 | # USB Peripheral Controller Support |
| 118 | # |
David Brownell | a7a19fa | 2008-08-14 17:04:48 -0700 | [diff] [blame] | 119 | # The order here is alphabetical, except that integrated controllers go |
| 120 | # before discrete ones so they will be the initial/default value: |
| 121 | # - integrated/SOC controllers first |
| 122 | # - licensed IP used in both SOC and discrete versions |
| 123 | # - discrete ones (including all PCI-only controllers) |
| 124 | # - debug/dummy gadget+hcd is last. |
| 125 | # |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 126 | choice |
| 127 | prompt "USB Peripheral Controller" |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 128 | help |
| 129 | A USB device uses a controller to talk to its host. |
| 130 | Systems should have only one such upstream link. |
| 131 | Many controller drivers are platform-specific; these |
| 132 | often need board-specific hooks. |
| 133 | |
David Brownell | a7a19fa | 2008-08-14 17:04:48 -0700 | [diff] [blame] | 134 | # |
| 135 | # Integrated controllers |
| 136 | # |
| 137 | |
Felipe Balbi | 193ab2a | 2011-06-22 17:28:10 +0300 | [diff] [blame] | 138 | config USB_AT91 |
| 139 | tristate "Atmel AT91 USB Device Port" |
Jean-Christophe PLAGNIOL-VILLARD | d1494a3 | 2012-01-28 22:35:36 +0800 | [diff] [blame^] | 140 | depends on ARCH_AT91 |
Thomas Dahlmann | 55d402d | 2007-07-16 21:40:54 -0700 | [diff] [blame] | 141 | help |
David Brownell | a7a19fa | 2008-08-14 17:04:48 -0700 | [diff] [blame] | 142 | Many Atmel AT91 processors (such as the AT91RM2000) have a |
| 143 | full speed USB Device Port with support for five configurable |
| 144 | endpoints (plus endpoint zero). |
Thomas Dahlmann | 55d402d | 2007-07-16 21:40:54 -0700 | [diff] [blame] | 145 | |
| 146 | Say "y" to link the driver statically, or "m" to build a |
David Brownell | a7a19fa | 2008-08-14 17:04:48 -0700 | [diff] [blame] | 147 | dynamically linked module called "at91_udc" and force all |
Thomas Dahlmann | 55d402d | 2007-07-16 21:40:54 -0700 | [diff] [blame] | 148 | gadget drivers to also be dynamically linked. |
| 149 | |
Felipe Balbi | 193ab2a | 2011-06-22 17:28:10 +0300 | [diff] [blame] | 150 | config USB_ATMEL_USBA |
| 151 | tristate "Atmel USBA" |
Haavard Skinnemoen | 914a3f3 | 2007-10-10 02:29:43 -0700 | [diff] [blame] | 152 | select USB_GADGET_DUALSPEED |
Jean-Christophe PLAGNIOL-VILLARD | 9918cea | 2012-01-26 14:07:09 +0100 | [diff] [blame] | 153 | depends on AVR32 || ARCH_AT91SAM9RL || ARCH_AT91SAM9G45 |
Haavard Skinnemoen | 914a3f3 | 2007-10-10 02:29:43 -0700 | [diff] [blame] | 154 | help |
| 155 | USBA is the integrated high-speed USB Device controller on |
Nicolas Ferre | ba45ca4 | 2008-04-08 13:59:18 +0100 | [diff] [blame] | 156 | the AT32AP700x, some AT91SAM9 and AT91CAP9 processors from Atmel. |
Haavard Skinnemoen | 914a3f3 | 2007-10-10 02:29:43 -0700 | [diff] [blame] | 157 | |
Felipe Balbi | 193ab2a | 2011-06-22 17:28:10 +0300 | [diff] [blame] | 158 | config USB_FSL_USB2 |
| 159 | tristate "Freescale Highspeed USB DR Peripheral Controller" |
Guennadi Liakhovetski | 54e4026b | 2009-04-15 14:25:33 +0200 | [diff] [blame] | 160 | depends on FSL_SOC || ARCH_MXC |
Li Yang | b504882 | 2007-04-23 10:54:25 -0700 | [diff] [blame] | 161 | select USB_GADGET_DUALSPEED |
Marc Kleine-Budde | 018b97d | 2010-10-29 11:04:49 +0200 | [diff] [blame] | 162 | select USB_FSL_MPH_DR_OF if OF |
Li Yang | b504882 | 2007-04-23 10:54:25 -0700 | [diff] [blame] | 163 | help |
| 164 | Some of Freescale PowerPC processors have a High Speed |
| 165 | Dual-Role(DR) USB controller, which supports device mode. |
| 166 | |
| 167 | The number of programmable endpoints is different through |
| 168 | SOC revisions. |
| 169 | |
| 170 | Say "y" to link the driver statically, or "m" to build a |
| 171 | dynamically linked module called "fsl_usb2_udc" and force |
| 172 | all gadget drivers to also be dynamically linked. |
| 173 | |
Felipe Balbi | 193ab2a | 2011-06-22 17:28:10 +0300 | [diff] [blame] | 174 | config USB_FUSB300 |
| 175 | tristate "Faraday FUSB300 USB Peripheral Controller" |
Sebastian Andrzej Siewior | ac17317 | 2011-07-05 16:39:48 +0300 | [diff] [blame] | 176 | depends on !PHYS_ADDR_T_64BIT |
Yuan-Hsin Chen | 0fe6f1d | 2011-01-18 14:49:28 +0800 | [diff] [blame] | 177 | select USB_GADGET_DUALSPEED |
| 178 | help |
| 179 | Faraday usb device controller FUSB300 driver |
| 180 | |
Felipe Balbi | 193ab2a | 2011-06-22 17:28:10 +0300 | [diff] [blame] | 181 | config USB_OMAP |
| 182 | tristate "OMAP USB Device Controller" |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 183 | depends on ARCH_OMAP |
Tony Lindgren | f1c9e15 | 2008-09-04 16:25:14 -0700 | [diff] [blame] | 184 | select ISP1301_OMAP if MACH_OMAP_H2 || MACH_OMAP_H3 || MACH_OMAP_H4_OTG |
David Brownell | 54b9ed3 | 2009-02-11 22:31:12 -0800 | [diff] [blame] | 185 | select USB_OTG_UTILS if ARCH_OMAP |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 186 | help |
| 187 | Many Texas Instruments OMAP processors have flexible full |
| 188 | speed USB device controllers, with support for up to 30 |
| 189 | endpoints (plus endpoint zero). This driver supports the |
| 190 | controller in the OMAP 1611, and should work with controllers |
| 191 | in other OMAP processors too, given minor tweaks. |
| 192 | |
| 193 | Say "y" to link the driver statically, or "m" to build a |
| 194 | dynamically linked module called "omap_udc" and force all |
| 195 | gadget drivers to also be dynamically linked. |
| 196 | |
Felipe Balbi | 193ab2a | 2011-06-22 17:28:10 +0300 | [diff] [blame] | 197 | config USB_PXA25X |
| 198 | tristate "PXA 25x or IXP 4xx" |
David Brownell | a7a19fa | 2008-08-14 17:04:48 -0700 | [diff] [blame] | 199 | depends on (ARCH_PXA && PXA25x) || ARCH_IXP4XX |
Russell King | 0996391 | 2009-10-21 13:20:32 +0100 | [diff] [blame] | 200 | select USB_OTG_UTILS |
David Brownell | a7a19fa | 2008-08-14 17:04:48 -0700 | [diff] [blame] | 201 | help |
| 202 | Intel's PXA 25x series XScale ARM-5TE processors include |
| 203 | an integrated full speed USB 1.1 device controller. The |
| 204 | controller in the IXP 4xx series is register-compatible. |
| 205 | |
| 206 | It has fifteen fixed-function endpoints, as well as endpoint |
| 207 | zero (for control transfers). |
| 208 | |
| 209 | Say "y" to link the driver statically, or "m" to build a |
| 210 | dynamically linked module called "pxa25x_udc" and force all |
| 211 | gadget drivers to also be dynamically linked. |
| 212 | |
David Brownell | a7a19fa | 2008-08-14 17:04:48 -0700 | [diff] [blame] | 213 | # if there's only one gadget driver, using only two bulk endpoints, |
| 214 | # don't waste memory for the other endpoints |
| 215 | config USB_PXA25X_SMALL |
Felipe Balbi | 193ab2a | 2011-06-22 17:28:10 +0300 | [diff] [blame] | 216 | depends on USB_PXA25X |
David Brownell | a7a19fa | 2008-08-14 17:04:48 -0700 | [diff] [blame] | 217 | bool |
| 218 | default n if USB_ETH_RNDIS |
| 219 | default y if USB_ZERO |
| 220 | default y if USB_ETH |
| 221 | default y if USB_G_SERIAL |
| 222 | |
Felipe Balbi | 193ab2a | 2011-06-22 17:28:10 +0300 | [diff] [blame] | 223 | config USB_R8A66597 |
| 224 | tristate "Renesas R8A66597 USB Peripheral Controller" |
Yoshihiro Shimoda | c414424 | 2009-08-19 04:59:39 +0000 | [diff] [blame] | 225 | select USB_GADGET_DUALSPEED |
| 226 | help |
| 227 | R8A66597 is a discrete USB host and peripheral controller chip that |
| 228 | supports both full and high speed USB 2.0 data transfers. |
| 229 | It has nine configurable endpoints, and endpoint zero. |
| 230 | |
| 231 | Say "y" to link the driver statically, or "m" to build a |
| 232 | dynamically linked module called "r8a66597_udc" and force all |
| 233 | gadget drivers to also be dynamically linked. |
| 234 | |
Kuninori Morimoto | 030ed1f | 2011-07-07 02:17:37 -0700 | [diff] [blame] | 235 | config USB_RENESAS_USBHS_UDC |
Felipe Balbi | 193ab2a | 2011-06-22 17:28:10 +0300 | [diff] [blame] | 236 | tristate 'Renesas USBHS controller' |
Kuninori Morimoto | 030ed1f | 2011-07-07 02:17:37 -0700 | [diff] [blame] | 237 | depends on USB_RENESAS_USBHS |
| 238 | select USB_GADGET_DUALSPEED |
Kuninori Morimoto | 2f98382 | 2011-04-05 11:40:54 +0900 | [diff] [blame] | 239 | help |
Felipe Balbi | 193ab2a | 2011-06-22 17:28:10 +0300 | [diff] [blame] | 240 | Renesas USBHS is a discrete USB host and peripheral controller chip |
| 241 | that supports both full and high speed USB 2.0 data transfers. |
| 242 | It has nine or more configurable endpoints, and endpoint zero. |
Kuninori Morimoto | 2f98382 | 2011-04-05 11:40:54 +0900 | [diff] [blame] | 243 | |
Felipe Balbi | 193ab2a | 2011-06-22 17:28:10 +0300 | [diff] [blame] | 244 | Say "y" to link the driver statically, or "m" to build a |
| 245 | dynamically linked module called "renesas_usbhs" and force all |
| 246 | gadget drivers to also be dynamically linked. |
Kuninori Morimoto | 2f98382 | 2011-04-05 11:40:54 +0900 | [diff] [blame] | 247 | |
Felipe Balbi | 193ab2a | 2011-06-22 17:28:10 +0300 | [diff] [blame] | 248 | config USB_PXA27X |
| 249 | tristate "PXA 27x" |
Robert Jarzmik | 9f5351b | 2009-04-21 20:34:44 -0700 | [diff] [blame] | 250 | depends on ARCH_PXA && (PXA27x || PXA3xx) |
Robert Jarzmik | 7fec3c2 | 2009-01-24 23:57:30 -0800 | [diff] [blame] | 251 | select USB_OTG_UTILS |
David Brownell | a7a19fa | 2008-08-14 17:04:48 -0700 | [diff] [blame] | 252 | help |
| 253 | Intel's PXA 27x series XScale ARM v5TE processors include |
| 254 | an integrated full speed USB 1.1 device controller. |
| 255 | |
| 256 | It has up to 23 endpoints, as well as endpoint zero (for |
| 257 | control transfers). |
| 258 | |
| 259 | Say "y" to link the driver statically, or "m" to build a |
| 260 | dynamically linked module called "pxa27x_udc" and force all |
| 261 | gadget drivers to also be dynamically linked. |
| 262 | |
Felipe Balbi | 193ab2a | 2011-06-22 17:28:10 +0300 | [diff] [blame] | 263 | config USB_S3C_HSOTG |
| 264 | tristate "S3C HS/OtG USB Device controller" |
Ben Dooks | 5b7d70c | 2009-06-02 14:58:06 +0100 | [diff] [blame] | 265 | depends on S3C_DEV_USB_HSOTG |
Maurus Cuelenaere | 0287e43 | 2010-05-25 05:36:49 +0100 | [diff] [blame] | 266 | select USB_GADGET_DUALSPEED |
Ben Dooks | 5b7d70c | 2009-06-02 14:58:06 +0100 | [diff] [blame] | 267 | help |
| 268 | The Samsung S3C64XX USB2.0 high-speed gadget controller |
| 269 | integrated into the S3C64XX series SoC. |
| 270 | |
Felipe Balbi | 193ab2a | 2011-06-22 17:28:10 +0300 | [diff] [blame] | 271 | config USB_IMX |
Sascha Hauer | 2e5a08a | 2011-08-24 08:41:11 +0200 | [diff] [blame] | 272 | tristate "Freescale i.MX1 USB Peripheral Controller" |
| 273 | depends on ARCH_MXC |
Paulius Zaleckas | c03e7d4 | 2009-06-09 11:11:16 +0300 | [diff] [blame] | 274 | help |
Sascha Hauer | 2e5a08a | 2011-08-24 08:41:11 +0200 | [diff] [blame] | 275 | Freescale's i.MX1 includes an integrated full speed |
| 276 | USB 1.1 device controller. |
Paulius Zaleckas | c03e7d4 | 2009-06-09 11:11:16 +0300 | [diff] [blame] | 277 | |
| 278 | It has Six fixed-function endpoints, as well as endpoint |
| 279 | zero (for control transfers). |
| 280 | |
| 281 | Say "y" to link the driver statically, or "m" to build a |
| 282 | dynamically linked module called "imx_udc" and force all |
| 283 | gadget drivers to also be dynamically linked. |
| 284 | |
Felipe Balbi | 193ab2a | 2011-06-22 17:28:10 +0300 | [diff] [blame] | 285 | config USB_S3C2410 |
| 286 | tristate "S3C2410 USB Device Controller" |
Arnaud Patard | 3fc154b | 2007-06-06 21:05:49 -0700 | [diff] [blame] | 287 | depends on ARCH_S3C2410 |
| 288 | help |
| 289 | Samsung's S3C2410 is an ARM-4 processor with an integrated |
| 290 | full speed USB 1.1 device controller. It has 4 configurable |
| 291 | endpoints, as well as endpoint zero (for control transfers). |
| 292 | |
| 293 | This driver has been tested on the S3C2410, S3C2412, and |
| 294 | S3C2440 processors. |
| 295 | |
Arnaud Patard | 3fc154b | 2007-06-06 21:05:49 -0700 | [diff] [blame] | 296 | config USB_S3C2410_DEBUG |
| 297 | boolean "S3C2410 udc debug messages" |
Felipe Balbi | 193ab2a | 2011-06-22 17:28:10 +0300 | [diff] [blame] | 298 | depends on USB_S3C2410 |
Arnaud Patard | 3fc154b | 2007-06-06 21:05:49 -0700 | [diff] [blame] | 299 | |
Felipe Balbi | 193ab2a | 2011-06-22 17:28:10 +0300 | [diff] [blame] | 300 | config USB_S3C_HSUDC |
| 301 | tristate "S3C2416, S3C2443 and S3C2450 USB Device Controller" |
Thomas Abraham | a9df304 | 2011-05-07 22:28:04 +0200 | [diff] [blame] | 302 | depends on ARCH_S3C2410 |
| 303 | select USB_GADGET_DUALSPEED |
| 304 | help |
| 305 | Samsung's S3C2416, S3C2443 and S3C2450 is an ARM9 based SoC |
| 306 | integrated with dual speed USB 2.0 device controller. It has |
| 307 | 8 endpoints, as well as endpoint zero. |
| 308 | |
| 309 | This driver has been tested on S3C2416 and S3C2450 processors. |
| 310 | |
Neil Zhang | 5e6c86b | 2011-12-20 13:20:21 +0800 | [diff] [blame] | 311 | config USB_MV_UDC |
| 312 | tristate "Marvell USB2.0 Device Controller" |
cxie4 | e7cddda | 2010-11-30 13:35:15 +0800 | [diff] [blame] | 313 | select USB_GADGET_DUALSPEED |
| 314 | help |
Neil Zhang | 5e6c86b | 2011-12-20 13:20:21 +0800 | [diff] [blame] | 315 | Marvell Socs (including PXA and MMP series) include a high speed |
| 316 | USB2.0 OTG controller, which can be configured as high speed or |
| 317 | full speed USB peripheral. |
Felipe Balbi | 72246da | 2011-08-19 18:10:58 +0300 | [diff] [blame] | 318 | |
David Brownell | a7a19fa | 2008-08-14 17:04:48 -0700 | [diff] [blame] | 319 | # |
| 320 | # Controllers available in both integrated and discrete versions |
| 321 | # |
| 322 | |
| 323 | # musb builds in ../musb along with host support |
| 324 | config USB_GADGET_MUSB_HDRC |
Felipe Balbi | 193ab2a | 2011-06-22 17:28:10 +0300 | [diff] [blame] | 325 | tristate "Inventra HDRC USB Peripheral (TI, ADI, ...)" |
Rabin Vincent | b61ae34 | 2011-07-18 18:38:47 +0530 | [diff] [blame] | 326 | depends on USB_MUSB_HDRC |
David Brownell | a7a19fa | 2008-08-14 17:04:48 -0700 | [diff] [blame] | 327 | select USB_GADGET_DUALSPEED |
David Brownell | bae4bd8 | 2006-01-22 10:32:37 -0800 | [diff] [blame] | 328 | help |
David Brownell | a7a19fa | 2008-08-14 17:04:48 -0700 | [diff] [blame] | 329 | This OTG-capable silicon IP is used in dual designs including |
Bryan Wu | 085ad40 | 2008-12-02 21:33:49 +0200 | [diff] [blame] | 330 | the TI DaVinci, OMAP 243x, OMAP 343x, TUSB 6010, and ADI Blackfin |
David Brownell | a7a19fa | 2008-08-14 17:04:48 -0700 | [diff] [blame] | 331 | |
Felipe Balbi | 193ab2a | 2011-06-22 17:28:10 +0300 | [diff] [blame] | 332 | config USB_M66592 |
| 333 | tristate "Renesas M66592 USB Peripheral Controller" |
David Brownell | a7a19fa | 2008-08-14 17:04:48 -0700 | [diff] [blame] | 334 | select USB_GADGET_DUALSPEED |
| 335 | help |
| 336 | M66592 is a discrete USB peripheral controller chip that |
| 337 | supports both full and high speed USB 2.0 data transfers. |
| 338 | It has seven configurable endpoints, and endpoint zero. |
David Brownell | bae4bd8 | 2006-01-22 10:32:37 -0800 | [diff] [blame] | 339 | |
| 340 | Say "y" to link the driver statically, or "m" to build a |
David Brownell | a7a19fa | 2008-08-14 17:04:48 -0700 | [diff] [blame] | 341 | dynamically linked module called "m66592_udc" and force all |
David Brownell | bae4bd8 | 2006-01-22 10:32:37 -0800 | [diff] [blame] | 342 | gadget drivers to also be dynamically linked. |
| 343 | |
David Brownell | a7a19fa | 2008-08-14 17:04:48 -0700 | [diff] [blame] | 344 | # |
| 345 | # Controllers available only in discrete form (and all PCI controllers) |
| 346 | # |
| 347 | |
Felipe Balbi | 193ab2a | 2011-06-22 17:28:10 +0300 | [diff] [blame] | 348 | config USB_AMD5536UDC |
| 349 | tristate "AMD5536 UDC" |
David Brownell | a7a19fa | 2008-08-14 17:04:48 -0700 | [diff] [blame] | 350 | depends on PCI |
| 351 | select USB_GADGET_DUALSPEED |
| 352 | help |
| 353 | The AMD5536 UDC is part of the AMD Geode CS5536, an x86 southbridge. |
| 354 | It is a USB Highspeed DMA capable USB device controller. Beside ep0 |
| 355 | it provides 4 IN and 4 OUT endpoints (bulk or interrupt type). |
| 356 | The UDC port supports OTG operation, and may be used as a host port |
| 357 | if it's not being used to implement peripheral or OTG roles. |
| 358 | |
| 359 | Say "y" to link the driver statically, or "m" to build a |
| 360 | dynamically linked module called "amd5536udc" and force all |
| 361 | gadget drivers to also be dynamically linked. |
| 362 | |
Felipe Balbi | 193ab2a | 2011-06-22 17:28:10 +0300 | [diff] [blame] | 363 | config USB_FSL_QE |
| 364 | tristate "Freescale QE/CPM USB Device Controller" |
Li Yang | 3948f0e | 2008-09-02 19:58:10 +0800 | [diff] [blame] | 365 | depends on FSL_SOC && (QUICC_ENGINE || CPM) |
| 366 | help |
| 367 | Some of Freescale PowerPC processors have a Full Speed |
| 368 | QE/CPM2 USB controller, which support device mode with 4 |
| 369 | programmable endpoints. This driver supports the |
| 370 | controller in the MPC8360 and MPC8272, and should work with |
| 371 | controllers having QE or CPM2, given minor tweaks. |
| 372 | |
| 373 | Set CONFIG_USB_GADGET to "m" to build this driver as a |
Matt LaPlante | 692105b | 2009-01-26 11:12:25 +0100 | [diff] [blame] | 374 | dynamically linked module called "fsl_qe_udc". |
Li Yang | 3948f0e | 2008-09-02 19:58:10 +0800 | [diff] [blame] | 375 | |
Felipe Balbi | 193ab2a | 2011-06-22 17:28:10 +0300 | [diff] [blame] | 376 | config USB_CI13XXX_PCI |
| 377 | tristate "MIPS USB CI13xxx PCI UDC" |
David Lopo | aa69a80 | 2008-11-17 14:14:51 -0800 | [diff] [blame] | 378 | depends on PCI |
| 379 | select USB_GADGET_DUALSPEED |
| 380 | help |
| 381 | MIPS USB IP core family device controller |
| 382 | Currently it only supports IP part number CI13412 |
| 383 | |
| 384 | Say "y" to link the driver statically, or "m" to build a |
| 385 | dynamically linked module called "ci13xxx_udc" and force all |
| 386 | gadget drivers to also be dynamically linked. |
| 387 | |
Felipe Balbi | 193ab2a | 2011-06-22 17:28:10 +0300 | [diff] [blame] | 388 | config USB_NET2272 |
| 389 | tristate "PLX NET2272" |
Seth Levy | ceb8036 | 2011-06-06 19:42:44 -0400 | [diff] [blame] | 390 | select USB_GADGET_DUALSPEED |
| 391 | help |
| 392 | PLX NET2272 is a USB peripheral controller which supports |
| 393 | both full and high speed USB 2.0 data transfers. |
| 394 | |
| 395 | It has three configurable endpoints, as well as endpoint zero |
| 396 | (for control transfer). |
| 397 | Say "y" to link the driver statically, or "m" to build a |
| 398 | dynamically linked module called "net2272" and force all |
| 399 | gadget drivers to also be dynamically linked. |
| 400 | |
Felipe Balbi | 193ab2a | 2011-06-22 17:28:10 +0300 | [diff] [blame] | 401 | config USB_NET2272_DMA |
Seth Levy | ceb8036 | 2011-06-06 19:42:44 -0400 | [diff] [blame] | 402 | boolean "Support external DMA controller" |
Felipe Balbi | 193ab2a | 2011-06-22 17:28:10 +0300 | [diff] [blame] | 403 | depends on USB_NET2272 |
Seth Levy | ceb8036 | 2011-06-06 19:42:44 -0400 | [diff] [blame] | 404 | help |
| 405 | The NET2272 part can optionally support an external DMA |
| 406 | controller, but your board has to have support in the |
| 407 | driver itself. |
| 408 | |
| 409 | If unsure, say "N" here. The driver works fine in PIO mode. |
| 410 | |
Felipe Balbi | 193ab2a | 2011-06-22 17:28:10 +0300 | [diff] [blame] | 411 | config USB_NET2280 |
| 412 | tristate "NetChip 228x" |
David Brownell | a7a19fa | 2008-08-14 17:04:48 -0700 | [diff] [blame] | 413 | depends on PCI |
| 414 | select USB_GADGET_DUALSPEED |
| 415 | help |
| 416 | NetChip 2280 / 2282 is a PCI based USB peripheral controller which |
| 417 | supports both full and high speed USB 2.0 data transfers. |
| 418 | |
| 419 | It has six configurable endpoints, as well as endpoint zero |
| 420 | (for control transfers) and several endpoints with dedicated |
| 421 | functions. |
| 422 | |
| 423 | Say "y" to link the driver statically, or "m" to build a |
| 424 | dynamically linked module called "net2280" and force all |
| 425 | gadget drivers to also be dynamically linked. |
| 426 | |
Felipe Balbi | 193ab2a | 2011-06-22 17:28:10 +0300 | [diff] [blame] | 427 | config USB_GOKU |
| 428 | tristate "Toshiba TC86C001 'Goku-S'" |
David Brownell | a7a19fa | 2008-08-14 17:04:48 -0700 | [diff] [blame] | 429 | depends on PCI |
| 430 | help |
| 431 | The Toshiba TC86C001 is a PCI device which includes controllers |
| 432 | for full speed USB devices, IDE, I2C, SIO, plus a USB host (OHCI). |
| 433 | |
| 434 | The device controller has three configurable (bulk or interrupt) |
| 435 | endpoints, plus endpoint zero (for control transfers). |
| 436 | |
| 437 | Say "y" to link the driver statically, or "m" to build a |
| 438 | dynamically linked module called "goku_udc" and to force all |
| 439 | gadget drivers to also be dynamically linked. |
| 440 | |
Felipe Balbi | 193ab2a | 2011-06-22 17:28:10 +0300 | [diff] [blame] | 441 | config USB_LANGWELL |
| 442 | tristate "Intel Langwell USB Device Controller" |
Xiaochen Shen | 5be19a9 | 2009-06-04 15:34:49 +0800 | [diff] [blame] | 443 | depends on PCI |
Sebastian Andrzej Siewior | ac17317 | 2011-07-05 16:39:48 +0300 | [diff] [blame] | 444 | depends on !PHYS_ADDR_T_64BIT |
Xiaochen Shen | 5be19a9 | 2009-06-04 15:34:49 +0800 | [diff] [blame] | 445 | select USB_GADGET_DUALSPEED |
| 446 | help |
| 447 | Intel Langwell USB Device Controller is a High-Speed USB |
| 448 | On-The-Go device controller. |
| 449 | |
| 450 | The number of programmable endpoints is different through |
| 451 | controller revision. |
| 452 | |
| 453 | Say "y" to link the driver statically, or "m" to build a |
| 454 | dynamically linked module called "langwell_udc" and force all |
| 455 | gadget drivers to also be dynamically linked. |
| 456 | |
Felipe Balbi | 193ab2a | 2011-06-22 17:28:10 +0300 | [diff] [blame] | 457 | config USB_EG20T |
Tomoya MORINAGA | 731ad81 | 2011-10-28 09:37:34 +0900 | [diff] [blame] | 458 | tristate "Intel EG20T PCH/LAPIS Semiconductor IOH(ML7213/ML7831) UDC" |
Toshiharu Okada | f646cf9 | 2010-11-11 18:27:57 +0900 | [diff] [blame] | 459 | depends on PCI |
| 460 | select USB_GADGET_DUALSPEED |
| 461 | help |
| 462 | This is a USB device driver for EG20T PCH. |
| 463 | EG20T PCH is the platform controller hub that is used in Intel's |
| 464 | general embedded platform. EG20T PCH has USB device interface. |
| 465 | Using this interface, it is able to access system devices connected |
| 466 | to USB device. |
| 467 | This driver enables USB device function. |
| 468 | USB device is a USB peripheral controller which |
| 469 | supports both full and high speed USB 2.0 data transfers. |
| 470 | This driver supports both control transfer and bulk transfer modes. |
| 471 | This driver dose not support interrupt transfer or isochronous |
| 472 | transfer modes. |
| 473 | |
Tomoya MORINAGA | 731ad81 | 2011-10-28 09:37:34 +0900 | [diff] [blame] | 474 | This driver also can be used for LAPIS Semiconductor's ML7213 which is |
Tomoya MORINAGA | 06f1b97 | 2011-01-06 09:16:31 +0900 | [diff] [blame] | 475 | for IVI(In-Vehicle Infotainment) use. |
Tomoya MORINAGA | 731ad81 | 2011-10-28 09:37:34 +0900 | [diff] [blame] | 476 | ML7831 is for general purpose use. |
| 477 | ML7213/ML7831 is companion chip for Intel Atom E6xx series. |
| 478 | ML7213/ML7831 is completely compatible for Intel EG20T PCH. |
Tomoya MORINAGA | 06f1b97 | 2011-01-06 09:16:31 +0900 | [diff] [blame] | 479 | |
Felipe Balbi | 193ab2a | 2011-06-22 17:28:10 +0300 | [diff] [blame] | 480 | config USB_CI13XXX_MSM |
| 481 | tristate "MIPS USB CI13xxx for MSM" |
Pavankumar Kondeti | 33f82f38 | 2010-12-07 17:54:03 +0530 | [diff] [blame] | 482 | depends on ARCH_MSM |
| 483 | select USB_GADGET_DUALSPEED |
Pavankumar Kondeti | dfb2130 | 2011-03-04 22:45:02 +0530 | [diff] [blame] | 484 | select USB_MSM_OTG |
Pavankumar Kondeti | 33f82f38 | 2010-12-07 17:54:03 +0530 | [diff] [blame] | 485 | help |
| 486 | MSM SoC has chipidea USB controller. This driver uses |
| 487 | ci13xxx_udc core. |
| 488 | This driver depends on OTG driver for PHY initialization, |
| 489 | clock management, powering up VBUS, and power management. |
Pavankumar Kondeti | 8cf28f1 | 2011-02-04 10:08:18 +0530 | [diff] [blame] | 490 | This driver is not supported on boards like trout which |
| 491 | has an external PHY. |
Pavankumar Kondeti | 33f82f38 | 2010-12-07 17:54:03 +0530 | [diff] [blame] | 492 | |
| 493 | Say "y" to link the driver statically, or "m" to build a |
| 494 | dynamically linked module called "ci13xxx_msm" and force all |
| 495 | gadget drivers to also be dynamically linked. |
| 496 | |
David Brownell | a7a19fa | 2008-08-14 17:04:48 -0700 | [diff] [blame] | 497 | # |
| 498 | # LAST -- dummy/emulated controller |
| 499 | # |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 500 | |
Felipe Balbi | 193ab2a | 2011-06-22 17:28:10 +0300 | [diff] [blame] | 501 | config USB_DUMMY_HCD |
| 502 | tristate "Dummy HCD (DEVELOPMENT)" |
Robert P. J. Day | afd0e0f | 2008-03-10 15:09:51 -0400 | [diff] [blame] | 503 | depends on USB=y || (USB=m && USB_GADGET=m) |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 504 | select USB_GADGET_DUALSPEED |
Tatyana Brokhman | 1cd8fd2 | 2011-06-29 16:41:52 +0300 | [diff] [blame] | 505 | select USB_GADGET_SUPERSPEED |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 506 | help |
| 507 | This host controller driver emulates USB, looping all data transfer |
| 508 | requests back to a USB "gadget driver" in the same host. The host |
| 509 | side is the master; the gadget side is the slave. Gadget drivers |
| 510 | can be high, full, or low speed; and they have access to endpoints |
| 511 | like those from NET2280, PXA2xx, or SA1100 hardware. |
Felipe Balbi | 193ab2a | 2011-06-22 17:28:10 +0300 | [diff] [blame] | 512 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 513 | This may help in some stages of creating a driver to embed in a |
| 514 | Linux device, since it lets you debug several parts of the gadget |
| 515 | driver without its hardware or drivers being involved. |
Felipe Balbi | 193ab2a | 2011-06-22 17:28:10 +0300 | [diff] [blame] | 516 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 517 | Since such a gadget side driver needs to interoperate with a host |
| 518 | side Linux-USB device driver, this may help to debug both sides |
| 519 | of a USB protocol stack. |
| 520 | |
| 521 | Say "y" to link the driver statically, or "m" to build a |
| 522 | dynamically linked module called "dummy_hcd" and force all |
| 523 | gadget drivers to also be dynamically linked. |
| 524 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 525 | # NOTE: Please keep dummy_hcd LAST so that "real hardware" appears |
| 526 | # first and will be selected by default. |
| 527 | |
| 528 | endchoice |
| 529 | |
Alan Stern | 97b2f90 | 2011-06-07 11:31:05 -0400 | [diff] [blame] | 530 | # Selected by UDC drivers that support high-speed operation. |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 531 | config USB_GADGET_DUALSPEED |
| 532 | bool |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 533 | |
Tatyana Brokhman | bdb64d7 | 2011-06-29 16:41:50 +0300 | [diff] [blame] | 534 | # Selected by UDC drivers that support super-speed opperation |
| 535 | config USB_GADGET_SUPERSPEED |
| 536 | bool |
Tatyana Brokhman | bdb64d7 | 2011-06-29 16:41:50 +0300 | [diff] [blame] | 537 | depends on USB_GADGET_DUALSPEED |
| 538 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 539 | # |
| 540 | # USB Gadget Drivers |
| 541 | # |
| 542 | choice |
| 543 | tristate "USB Gadget Drivers" |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 544 | default USB_ETH |
| 545 | help |
| 546 | A Linux "Gadget Driver" talks to the USB Peripheral Controller |
| 547 | driver through the abstract "gadget" API. Some other operating |
| 548 | systems call these "client" drivers, of which "class drivers" |
| 549 | are a subset (implementing a USB device class specification). |
| 550 | A gadget driver implements one or more USB functions using |
| 551 | the peripheral hardware. |
| 552 | |
| 553 | Gadget drivers are hardware-neutral, or "platform independent", |
| 554 | except that they sometimes must understand quirks or limitations |
| 555 | of the particular controllers they work with. For example, when |
| 556 | a controller doesn't support alternate configurations or provide |
| 557 | enough of the right types of endpoints, the gadget driver might |
| 558 | not be able work with that controller, or might need to implement |
| 559 | a less common variant of a device class protocol. |
| 560 | |
| 561 | # this first set of drivers all depend on bulk-capable hardware. |
| 562 | |
| 563 | config USB_ZERO |
| 564 | tristate "Gadget Zero (DEVELOPMENT)" |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 565 | help |
| 566 | Gadget Zero is a two-configuration device. It either sinks and |
| 567 | sources bulk data; or it loops back a configurable number of |
| 568 | transfers. It also implements control requests, for "chapter 9" |
| 569 | conformance. The driver needs only two bulk-capable endpoints, so |
| 570 | it can work on top of most device-side usb controllers. It's |
| 571 | useful for testing, and is also a working example showing how |
| 572 | USB "gadget drivers" can be written. |
| 573 | |
| 574 | Make this be the first driver you try using on top of any new |
| 575 | USB peripheral controller driver. Then you can use host-side |
| 576 | test software, like the "usbtest" driver, to put your hardware |
| 577 | and its driver through a basic set of functional tests. |
| 578 | |
| 579 | Gadget Zero also works with the host-side "usb-skeleton" driver, |
| 580 | and with many kinds of host-side test software. You may need |
| 581 | to tweak product and vendor IDs before host software knows about |
| 582 | this device, and arrange to select an appropriate configuration. |
| 583 | |
| 584 | Say "y" to link the driver statically, or "m" to build a |
| 585 | dynamically linked module called "g_zero". |
| 586 | |
| 587 | config USB_ZERO_HNPTEST |
| 588 | boolean "HNP Test Device" |
| 589 | depends on USB_ZERO && USB_OTG |
| 590 | help |
| 591 | You can configure this device to enumerate using the device |
| 592 | identifiers of the USB-OTG test device. That means that when |
| 593 | this gadget connects to another OTG device, with this one using |
| 594 | the "B-Peripheral" role, that device will use HNP to let this |
| 595 | one serve as the USB host instead (in the "B-Host" role). |
| 596 | |
Bryan Wu | c6994e6 | 2009-06-03 09:17:58 -0400 | [diff] [blame] | 597 | config USB_AUDIO |
| 598 | tristate "Audio Gadget (EXPERIMENTAL)" |
| 599 | depends on SND |
Randy Dunlap | 0495073 | 2009-07-03 13:26:57 -0700 | [diff] [blame] | 600 | select SND_PCM |
Bryan Wu | c6994e6 | 2009-06-03 09:17:58 -0400 | [diff] [blame] | 601 | help |
| 602 | Gadget Audio is compatible with USB Audio Class specification 1.0. |
| 603 | It will include at least one AudioControl interface, zero or more |
| 604 | AudioStream interface and zero or more MIDIStream interface. |
| 605 | |
| 606 | Gadget Audio will use on-board ALSA (CONFIG_SND) audio card to |
| 607 | playback or capture audio stream. |
| 608 | |
| 609 | Say "y" to link the driver statically, or "m" to build a |
| 610 | dynamically linked module called "g_audio". |
| 611 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 612 | config USB_ETH |
| 613 | tristate "Ethernet Gadget (with CDC Ethernet support)" |
| 614 | depends on NET |
Randy Dunlap | 9e221be | 2009-09-07 17:08:39 -0700 | [diff] [blame] | 615 | select CRC32 |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 616 | help |
Brian Niebuhr | 9b39e9d | 2009-08-14 10:04:22 -0500 | [diff] [blame] | 617 | This driver implements Ethernet style communication, in one of |
| 618 | several ways: |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 619 | |
| 620 | - The "Communication Device Class" (CDC) Ethernet Control Model. |
| 621 | That protocol is often avoided with pure Ethernet adapters, in |
| 622 | favor of simpler vendor-specific hardware, but is widely |
| 623 | supported by firmware for smart network devices. |
| 624 | |
| 625 | - On hardware can't implement that protocol, a simple CDC subset |
| 626 | is used, placing fewer demands on USB. |
| 627 | |
Brian Niebuhr | 9b39e9d | 2009-08-14 10:04:22 -0500 | [diff] [blame] | 628 | - CDC Ethernet Emulation Model (EEM) is a newer standard that has |
| 629 | a simpler interface that can be used by more USB hardware. |
| 630 | |
| 631 | RNDIS support is an additional option, more demanding than than |
| 632 | subset. |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 633 | |
| 634 | Within the USB device, this gadget driver exposes a network device |
| 635 | "usbX", where X depends on what other networking devices you have. |
| 636 | Treat it like a two-node Ethernet link: host, and gadget. |
| 637 | |
| 638 | The Linux-USB host-side "usbnet" driver interoperates with this |
| 639 | driver, so that deep I/O queues can be supported. On 2.4 kernels, |
| 640 | use "CDCEther" instead, if you're using the CDC option. That CDC |
| 641 | mode should also interoperate with standard CDC Ethernet class |
| 642 | drivers on other host operating systems. |
| 643 | |
| 644 | Say "y" to link the driver statically, or "m" to build a |
| 645 | dynamically linked module called "g_ether". |
| 646 | |
| 647 | config USB_ETH_RNDIS |
Robert P. J. Day | afd0e0f | 2008-03-10 15:09:51 -0400 | [diff] [blame] | 648 | bool "RNDIS support" |
| 649 | depends on USB_ETH |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 650 | default y |
| 651 | help |
| 652 | Microsoft Windows XP bundles the "Remote NDIS" (RNDIS) protocol, |
| 653 | and Microsoft provides redistributable binary RNDIS drivers for |
| 654 | older versions of Windows. |
| 655 | |
| 656 | If you say "y" here, the Ethernet gadget driver will try to provide |
| 657 | a second device configuration, supporting RNDIS to talk to such |
| 658 | Microsoft USB hosts. |
| 659 | |
| 660 | To make MS-Windows work with this, use Documentation/usb/linux.inf |
| 661 | as the "driver info file". For versions of MS-Windows older than |
| 662 | XP, you'll need to download drivers from Microsoft's website; a URL |
| 663 | is given in comments found in that info file. |
| 664 | |
Brian Niebuhr | 9b39e9d | 2009-08-14 10:04:22 -0500 | [diff] [blame] | 665 | config USB_ETH_EEM |
| 666 | bool "Ethernet Emulation Model (EEM) support" |
| 667 | depends on USB_ETH |
| 668 | default n |
| 669 | help |
| 670 | CDC EEM is a newer USB standard that is somewhat simpler than CDC ECM |
| 671 | and therefore can be supported by more hardware. Technically ECM and |
| 672 | EEM are designed for different applications. The ECM model extends |
| 673 | the network interface to the target (e.g. a USB cable modem), and the |
| 674 | EEM model is for mobile devices to communicate with hosts using |
| 675 | ethernet over USB. For Linux gadgets, however, the interface with |
| 676 | the host is the same (a usbX device), so the differences are minimal. |
| 677 | |
| 678 | If you say "y" here, the Ethernet gadget driver will use the EEM |
| 679 | protocol rather than ECM. If unsure, say "n". |
| 680 | |
Yauheni Kaliuta | 6c34d28 | 2010-12-08 13:12:06 +0200 | [diff] [blame] | 681 | config USB_G_NCM |
| 682 | tristate "Network Control Model (NCM) support" |
| 683 | depends on NET |
| 684 | select CRC32 |
| 685 | help |
| 686 | This driver implements USB CDC NCM subclass standard. NCM is |
| 687 | an advanced protocol for Ethernet encapsulation, allows grouping |
| 688 | of several ethernet frames into one USB transfer and diffferent |
| 689 | alignment possibilities. |
| 690 | |
| 691 | Say "y" to link the driver statically, or "m" to build a |
| 692 | dynamically linked module called "g_ncm". |
| 693 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 694 | config USB_GADGETFS |
| 695 | tristate "Gadget Filesystem (EXPERIMENTAL)" |
| 696 | depends on EXPERIMENTAL |
| 697 | help |
| 698 | This driver provides a filesystem based API that lets user mode |
| 699 | programs implement a single-configuration USB device, including |
| 700 | endpoint I/O and control requests that don't relate to enumeration. |
| 701 | All endpoints, transfer speeds, and transfer types supported by |
| 702 | the hardware are available, through read() and write() calls. |
| 703 | |
Robert P. J. Day | afd0e0f | 2008-03-10 15:09:51 -0400 | [diff] [blame] | 704 | Currently, this option is still labelled as EXPERIMENTAL because |
| 705 | of existing race conditions in the underlying in-kernel AIO core. |
| 706 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 707 | Say "y" to link the driver statically, or "m" to build a |
| 708 | dynamically linked module called "gadgetfs". |
| 709 | |
Michal Nazarewicz | c6c5600 | 2010-05-05 12:53:15 +0200 | [diff] [blame] | 710 | config USB_FUNCTIONFS |
| 711 | tristate "Function Filesystem (EXPERIMENTAL)" |
| 712 | depends on EXPERIMENTAL |
Michal Nazarewicz | f8dae53 | 2010-06-25 16:29:27 +0200 | [diff] [blame] | 713 | select USB_FUNCTIONFS_GENERIC if !(USB_FUNCTIONFS_ETH || USB_FUNCTIONFS_RNDIS) |
Michal Nazarewicz | c6c5600 | 2010-05-05 12:53:15 +0200 | [diff] [blame] | 714 | help |
Michael Prokop | eabf0f5 | 2010-09-06 09:53:48 +0200 | [diff] [blame] | 715 | The Function Filesystem (FunctionFS) lets one create USB |
| 716 | composite functions in user space in the same way GadgetFS |
Michal Nazarewicz | c6c5600 | 2010-05-05 12:53:15 +0200 | [diff] [blame] | 717 | lets one create USB gadgets in user space. This allows creation |
| 718 | of composite gadgets such that some of the functions are |
| 719 | implemented in kernel space (for instance Ethernet, serial or |
| 720 | mass storage) and other are implemented in user space. |
| 721 | |
Michal Nazarewicz | f8dae53 | 2010-06-25 16:29:27 +0200 | [diff] [blame] | 722 | If you say "y" or "m" here you will be able what kind of |
| 723 | configurations the gadget will provide. |
| 724 | |
Michal Nazarewicz | c6c5600 | 2010-05-05 12:53:15 +0200 | [diff] [blame] | 725 | Say "y" to link the driver statically, or "m" to build |
| 726 | a dynamically linked module called "g_ffs". |
| 727 | |
| 728 | config USB_FUNCTIONFS_ETH |
Michal Nazarewicz | f8dae53 | 2010-06-25 16:29:27 +0200 | [diff] [blame] | 729 | bool "Include configuration with CDC ECM (Ethernet)" |
Randy Dunlap | 17b2765 | 2010-05-13 09:41:12 -0700 | [diff] [blame] | 730 | depends on USB_FUNCTIONFS && NET |
Michal Nazarewicz | c6c5600 | 2010-05-05 12:53:15 +0200 | [diff] [blame] | 731 | help |
Michael Prokop | eabf0f5 | 2010-09-06 09:53:48 +0200 | [diff] [blame] | 732 | Include a configuration with CDC ECM function (Ethernet) and the |
| 733 | Function Filesystem. |
Michal Nazarewicz | c6c5600 | 2010-05-05 12:53:15 +0200 | [diff] [blame] | 734 | |
| 735 | config USB_FUNCTIONFS_RNDIS |
Michal Nazarewicz | f8dae53 | 2010-06-25 16:29:27 +0200 | [diff] [blame] | 736 | bool "Include configuration with RNDIS (Ethernet)" |
Randy Dunlap | 17b2765 | 2010-05-13 09:41:12 -0700 | [diff] [blame] | 737 | depends on USB_FUNCTIONFS && NET |
Michal Nazarewicz | c6c5600 | 2010-05-05 12:53:15 +0200 | [diff] [blame] | 738 | help |
Michael Prokop | eabf0f5 | 2010-09-06 09:53:48 +0200 | [diff] [blame] | 739 | Include a configuration with RNDIS function (Ethernet) and the Filesystem. |
Michal Nazarewicz | c6c5600 | 2010-05-05 12:53:15 +0200 | [diff] [blame] | 740 | |
| 741 | config USB_FUNCTIONFS_GENERIC |
| 742 | bool "Include 'pure' configuration" |
Michal Nazarewicz | f8dae53 | 2010-06-25 16:29:27 +0200 | [diff] [blame] | 743 | depends on USB_FUNCTIONFS |
Michal Nazarewicz | c6c5600 | 2010-05-05 12:53:15 +0200 | [diff] [blame] | 744 | help |
Michal Nazarewicz | f8dae53 | 2010-06-25 16:29:27 +0200 | [diff] [blame] | 745 | Include a configuration with the Function Filesystem alone with |
| 746 | no Ethernet interface. |
Michal Nazarewicz | c6c5600 | 2010-05-05 12:53:15 +0200 | [diff] [blame] | 747 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 748 | config USB_FILE_STORAGE |
Alan Stern | 664a51a | 2011-06-15 16:31:37 -0400 | [diff] [blame] | 749 | tristate "File-backed Storage Gadget (DEPRECATED)" |
Randy Dunlap | 8784028 | 2007-03-21 13:57:51 -0700 | [diff] [blame] | 750 | depends on BLOCK |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 751 | help |
| 752 | The File-backed Storage Gadget acts as a USB Mass Storage |
| 753 | disk drive. As its storage repository it can use a regular |
| 754 | file or a block device (in much the same way as the "loop" |
| 755 | device driver), specified as a module parameter. |
| 756 | |
| 757 | Say "y" to link the driver statically, or "m" to build a |
| 758 | dynamically linked module called "g_file_storage". |
| 759 | |
Alan Stern | 664a51a | 2011-06-15 16:31:37 -0400 | [diff] [blame] | 760 | NOTE: This driver is deprecated. Its replacement is the |
| 761 | Mass Storage Gadget. |
| 762 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 763 | config USB_FILE_STORAGE_TEST |
| 764 | bool "File-backed Storage Gadget testing version" |
| 765 | depends on USB_FILE_STORAGE |
| 766 | default n |
| 767 | help |
| 768 | Say "y" to generate the larger testing version of the |
| 769 | File-backed Storage Gadget, useful for probing the |
| 770 | behavior of USB Mass Storage hosts. Not needed for |
| 771 | normal operation. |
| 772 | |
Michal Nazarewicz | d23b0f0 | 2009-11-09 14:15:20 +0100 | [diff] [blame] | 773 | config USB_MASS_STORAGE |
| 774 | tristate "Mass Storage Gadget" |
| 775 | depends on BLOCK |
| 776 | help |
| 777 | The Mass Storage Gadget acts as a USB Mass Storage disk drive. |
| 778 | As its storage repository it can use a regular file or a block |
| 779 | device (in much the same way as the "loop" device driver), |
| 780 | specified as a module parameter or sysfs option. |
| 781 | |
Alan Stern | 664a51a | 2011-06-15 16:31:37 -0400 | [diff] [blame] | 782 | This driver is an updated replacement for the deprecated |
| 783 | File-backed Storage Gadget (g_file_storage). |
Michal Nazarewicz | d23b0f0 | 2009-11-09 14:15:20 +0100 | [diff] [blame] | 784 | |
| 785 | Say "y" to link the driver statically, or "m" to build |
Alan Stern | 664a51a | 2011-06-15 16:31:37 -0400 | [diff] [blame] | 786 | a dynamically linked module called "g_mass_storage". |
Michal Nazarewicz | d23b0f0 | 2009-11-09 14:15:20 +0100 | [diff] [blame] | 787 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 788 | config USB_G_SERIAL |
Felipe Balbi | 3086775 | 2008-08-18 17:39:30 -0700 | [diff] [blame] | 789 | tristate "Serial Gadget (with CDC ACM and CDC OBEX support)" |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 790 | help |
| 791 | The Serial Gadget talks to the Linux-USB generic serial driver. |
| 792 | This driver supports a CDC-ACM module option, which can be used |
| 793 | to interoperate with MS-Windows hosts or with the Linux-USB |
| 794 | "cdc-acm" driver. |
| 795 | |
Felipe Balbi | 3086775 | 2008-08-18 17:39:30 -0700 | [diff] [blame] | 796 | This driver also supports a CDC-OBEX option. You will need a |
| 797 | user space OBEX server talking to /dev/ttyGS*, since the kernel |
| 798 | itself doesn't implement the OBEX protocol. |
| 799 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 800 | Say "y" to link the driver statically, or "m" to build a |
| 801 | dynamically linked module called "g_serial". |
| 802 | |
| 803 | For more information, see Documentation/usb/gadget_serial.txt |
| 804 | which includes instructions and a "driver info file" needed to |
Felipe Balbi | 3086775 | 2008-08-18 17:39:30 -0700 | [diff] [blame] | 805 | make MS-Windows work with CDC ACM. |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 806 | |
Ben Williamson | f2ebf92c | 2006-08-01 11:28:16 +1000 | [diff] [blame] | 807 | config USB_MIDI_GADGET |
| 808 | tristate "MIDI Gadget (EXPERIMENTAL)" |
| 809 | depends on SND && EXPERIMENTAL |
| 810 | select SND_RAWMIDI |
| 811 | help |
| 812 | The MIDI Gadget acts as a USB Audio device, with one MIDI |
| 813 | input and one MIDI output. These MIDI jacks appear as |
| 814 | a sound "card" in the ALSA sound system. Other MIDI |
| 815 | connections can then be made on the gadget system, using |
| 816 | ALSA's aconnect utility etc. |
| 817 | |
| 818 | Say "y" to link the driver statically, or "m" to build a |
| 819 | dynamically linked module called "g_midi". |
| 820 | |
Craig W. Nadler | 25a010c | 2007-11-11 15:00:15 -0800 | [diff] [blame] | 821 | config USB_G_PRINTER |
| 822 | tristate "Printer Gadget" |
| 823 | help |
| 824 | The Printer Gadget channels data between the USB host and a |
| 825 | userspace program driving the print engine. The user space |
| 826 | program reads and writes the device file /dev/g_printer to |
| 827 | receive or send printer data. It can use ioctl calls to |
| 828 | the device file to get or set printer status. |
| 829 | |
| 830 | Say "y" to link the driver statically, or "m" to build a |
| 831 | dynamically linked module called "g_printer". |
| 832 | |
| 833 | For more information, see Documentation/usb/gadget_printer.txt |
| 834 | which includes sample code for accessing the device file. |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 835 | |
David Brownell | 19e2068 | 2008-06-19 18:20:26 -0700 | [diff] [blame] | 836 | config USB_CDC_COMPOSITE |
| 837 | tristate "CDC Composite Device (Ethernet and ACM)" |
Randy Dunlap | 4ddd9ec | 2008-07-03 14:44:59 -0700 | [diff] [blame] | 838 | depends on NET |
David Brownell | 19e2068 | 2008-06-19 18:20:26 -0700 | [diff] [blame] | 839 | help |
| 840 | This driver provides two functions in one configuration: |
| 841 | a CDC Ethernet (ECM) link, and a CDC ACM (serial port) link. |
| 842 | |
| 843 | This driver requires four bulk and two interrupt endpoints, |
| 844 | plus the ability to handle altsettings. Not all peripheral |
| 845 | controllers are that capable. |
| 846 | |
| 847 | Say "y" to link the driver statically, or "m" to build a |
| 848 | dynamically linked module. |
| 849 | |
Felipe Balbi | f358f5b | 2010-01-05 16:10:13 +0200 | [diff] [blame] | 850 | config USB_G_NOKIA |
| 851 | tristate "Nokia composite gadget" |
| 852 | depends on PHONET |
| 853 | help |
| 854 | The Nokia composite gadget provides support for acm, obex |
| 855 | and phonet in only one composite gadget driver. |
| 856 | |
| 857 | It's only really useful for N900 hardware. If you're building |
| 858 | a kernel for N900, say Y or M here. If unsure, say N. |
| 859 | |
Klaus Schwarzkopf | fa3ae0c | 2011-10-10 10:32:23 +0200 | [diff] [blame] | 860 | config USB_G_ACM_MS |
| 861 | tristate "CDC Composite Device (ACM and mass storage)" |
| 862 | depends on BLOCK |
| 863 | help |
| 864 | This driver provides two functions in one configuration: |
| 865 | a mass storage, and a CDC ACM (serial port) link. |
| 866 | |
| 867 | Say "y" to link the driver statically, or "m" to build a |
| 868 | dynamically linked module called "g_acm_ms". |
| 869 | |
Michal Nazarewicz | f176a5d | 2009-11-09 14:15:27 +0100 | [diff] [blame] | 870 | config USB_G_MULTI |
| 871 | tristate "Multifunction Composite Gadget (EXPERIMENTAL)" |
Randy Dunlap | 5791e10 | 2009-12-06 10:03:02 -0800 | [diff] [blame] | 872 | depends on BLOCK && NET |
Michal Nazarewicz | 279cc49 | 2010-06-21 13:57:03 +0200 | [diff] [blame] | 873 | select USB_G_MULTI_CDC if !USB_G_MULTI_RNDIS |
Michal Nazarewicz | f176a5d | 2009-11-09 14:15:27 +0100 | [diff] [blame] | 874 | help |
| 875 | The Multifunction Composite Gadget provides Ethernet (RNDIS |
| 876 | and/or CDC Ethernet), mass storage and ACM serial link |
| 877 | interfaces. |
| 878 | |
Randy Dunlap | 5791e10 | 2009-12-06 10:03:02 -0800 | [diff] [blame] | 879 | You will be asked to choose which of the two configurations is |
Michal Nazarewicz | f176a5d | 2009-11-09 14:15:27 +0100 | [diff] [blame] | 880 | to be available in the gadget. At least one configuration must |
Randy Dunlap | 5791e10 | 2009-12-06 10:03:02 -0800 | [diff] [blame] | 881 | be chosen to make the gadget usable. Selecting more than one |
Michal Nazarewicz | f176a5d | 2009-11-09 14:15:27 +0100 | [diff] [blame] | 882 | configuration will prevent Windows from automatically detecting |
Randy Dunlap | 5791e10 | 2009-12-06 10:03:02 -0800 | [diff] [blame] | 883 | the gadget as a composite gadget, so an INF file will be needed to |
Michal Nazarewicz | f176a5d | 2009-11-09 14:15:27 +0100 | [diff] [blame] | 884 | use the gadget. |
| 885 | |
| 886 | Say "y" to link the driver statically, or "m" to build a |
| 887 | dynamically linked module called "g_multi". |
| 888 | |
| 889 | config USB_G_MULTI_RNDIS |
| 890 | bool "RNDIS + CDC Serial + Storage configuration" |
| 891 | depends on USB_G_MULTI |
| 892 | default y |
| 893 | help |
| 894 | This option enables a configuration with RNDIS, CDC Serial and |
| 895 | Mass Storage functions available in the Multifunction Composite |
Randy Dunlap | 5791e10 | 2009-12-06 10:03:02 -0800 | [diff] [blame] | 896 | Gadget. This is the configuration dedicated for Windows since RNDIS |
| 897 | is Microsoft's protocol. |
Michal Nazarewicz | f176a5d | 2009-11-09 14:15:27 +0100 | [diff] [blame] | 898 | |
| 899 | If unsure, say "y". |
| 900 | |
| 901 | config USB_G_MULTI_CDC |
| 902 | bool "CDC Ethernet + CDC Serial + Storage configuration" |
| 903 | depends on USB_G_MULTI |
| 904 | default n |
| 905 | help |
| 906 | This option enables a configuration with CDC Ethernet (ECM), CDC |
| 907 | Serial and Mass Storage functions available in the Multifunction |
Randy Dunlap | 5791e10 | 2009-12-06 10:03:02 -0800 | [diff] [blame] | 908 | Composite Gadget. |
Michal Nazarewicz | f176a5d | 2009-11-09 14:15:27 +0100 | [diff] [blame] | 909 | |
| 910 | If unsure, say "y". |
| 911 | |
Fabien Chouteau | 71adf11 | 2010-04-08 09:31:15 +0200 | [diff] [blame] | 912 | config USB_G_HID |
| 913 | tristate "HID Gadget" |
| 914 | help |
| 915 | The HID gadget driver provides generic emulation of USB |
| 916 | Human Interface Devices (HID). |
| 917 | |
| 918 | For more information, see Documentation/usb/gadget_hid.txt which |
| 919 | includes sample code for accessing the device files. |
| 920 | |
| 921 | Say "y" to link the driver statically, or "m" to build a |
| 922 | dynamically linked module called "g_hid". |
Michal Nazarewicz | f176a5d | 2009-11-09 14:15:27 +0100 | [diff] [blame] | 923 | |
stephane duverger | f6c826a | 2010-07-12 18:37:53 +0200 | [diff] [blame] | 924 | config USB_G_DBGP |
| 925 | tristate "EHCI Debug Device Gadget" |
| 926 | help |
| 927 | This gadget emulates an EHCI Debug device. This is useful when you want |
| 928 | to interact with an EHCI Debug Port. |
| 929 | |
| 930 | Say "y" to link the driver statically, or "m" to build a |
| 931 | dynamically linked module called "g_dbgp". |
| 932 | |
| 933 | if USB_G_DBGP |
| 934 | choice |
| 935 | prompt "EHCI Debug Device mode" |
| 936 | default USB_G_DBGP_SERIAL |
| 937 | |
| 938 | config USB_G_DBGP_PRINTK |
| 939 | depends on USB_G_DBGP |
| 940 | bool "printk" |
| 941 | help |
| 942 | Directly printk() received data. No interaction. |
| 943 | |
| 944 | config USB_G_DBGP_SERIAL |
| 945 | depends on USB_G_DBGP |
| 946 | bool "serial" |
| 947 | help |
| 948 | Userland can interact using /dev/ttyGSxxx. |
| 949 | endchoice |
| 950 | endif |
| 951 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 952 | # put drivers that need isochronous transfer support (for audio |
| 953 | # or video class gadget drivers), or specific hardware, here. |
Laurent Pinchart | a9914127 | 2010-05-02 20:57:42 +0200 | [diff] [blame] | 954 | config USB_G_WEBCAM |
| 955 | tristate "USB Webcam Gadget" |
Randy Dunlap | 24337c1 | 2010-05-05 15:46:26 -0700 | [diff] [blame] | 956 | depends on VIDEO_DEV |
Laurent Pinchart | a9914127 | 2010-05-02 20:57:42 +0200 | [diff] [blame] | 957 | help |
| 958 | The Webcam Gadget acts as a composite USB Audio and Video Class |
| 959 | device. It provides a userspace API to process UVC control requests |
| 960 | and stream video data to the host. |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 961 | |
Laurent Pinchart | a9914127 | 2010-05-02 20:57:42 +0200 | [diff] [blame] | 962 | Say "y" to link the driver statically, or "m" to build a |
| 963 | dynamically linked module called "g_webcam". |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 964 | |
| 965 | endchoice |
| 966 | |
Denis Cheng | b75be4a | 2008-01-24 16:36:31 +0800 | [diff] [blame] | 967 | endif # USB_GADGET |