blob: f12007b80a466e33fad7efb03dfe7e4f20913462 [file] [log] [blame]
Linus Torvalds1da177e2005-04-16 15:20:36 -07001/proc/sys/net/ipv4/* Variables:
2
3ip_forward - BOOLEAN
4 0 - disabled (default)
5 not 0 - enabled
6
7 Forward Packets between interfaces.
8
9 This variable is special, its change resets all configuration
10 parameters to their default state (RFC1122 for hosts, RFC1812
11 for routers)
12
13ip_default_ttl - INTEGER
14 default 64
15
16ip_no_pmtu_disc - BOOLEAN
17 Disable Path MTU Discovery.
18 default FALSE
19
20min_pmtu - INTEGER
21 default 562 - minimum discovered Path MTU
22
23mtu_expires - INTEGER
24 Time, in seconds, that cached PMTU information is kept.
25
26min_adv_mss - INTEGER
27 The advertised MSS depends on the first hop route MTU, but will
28 never be lower than this setting.
29
30IP Fragmentation:
31
32ipfrag_high_thresh - INTEGER
33 Maximum memory used to reassemble IP fragments. When
34 ipfrag_high_thresh bytes of memory is allocated for this purpose,
35 the fragment handler will toss packets until ipfrag_low_thresh
36 is reached.
37
38ipfrag_low_thresh - INTEGER
39 See ipfrag_high_thresh
40
41ipfrag_time - INTEGER
42 Time in seconds to keep an IP fragment in memory.
43
44ipfrag_secret_interval - INTEGER
45 Regeneration interval (in seconds) of the hash secret (or lifetime
46 for the hash secret) for IP fragments.
47 Default: 600
48
Herbert Xu89cee8b2005-12-13 23:14:27 -080049ipfrag_max_dist - INTEGER
50 ipfrag_max_dist is a non-negative integer value which defines the
51 maximum "disorder" which is allowed among fragments which share a
52 common IP source address. Note that reordering of packets is
53 not unusual, but if a large number of fragments arrive from a source
54 IP address while a particular fragment queue remains incomplete, it
55 probably indicates that one or more fragments belonging to that queue
56 have been lost. When ipfrag_max_dist is positive, an additional check
57 is done on fragments before they are added to a reassembly queue - if
58 ipfrag_max_dist (or more) fragments have arrived from a particular IP
59 address between additions to any IP fragment queue using that source
60 address, it's presumed that one or more fragments in the queue are
61 lost. The existing fragment queue will be dropped, and a new one
62 started. An ipfrag_max_dist value of zero disables this check.
63
64 Using a very small value, e.g. 1 or 2, for ipfrag_max_dist can
65 result in unnecessarily dropping fragment queues when normal
66 reordering of packets occurs, which could lead to poor application
67 performance. Using a very large value, e.g. 50000, increases the
68 likelihood of incorrectly reassembling IP fragments that originate
69 from different IP datagrams, which could result in data corruption.
70 Default: 64
71
Linus Torvalds1da177e2005-04-16 15:20:36 -070072INET peer storage:
73
74inet_peer_threshold - INTEGER
75 The approximate size of the storage. Starting from this threshold
76 entries will be thrown aggressively. This threshold also determines
77 entries' time-to-live and time intervals between garbage collection
78 passes. More entries, less time-to-live, less GC interval.
79
80inet_peer_minttl - INTEGER
81 Minimum time-to-live of entries. Should be enough to cover fragment
82 time-to-live on the reassembling side. This minimum time-to-live is
83 guaranteed if the pool size is less than inet_peer_threshold.
84 Measured in jiffies(1).
85
86inet_peer_maxttl - INTEGER
87 Maximum time-to-live of entries. Unused entries will expire after
88 this period of time if there is no memory pressure on the pool (i.e.
89 when the number of entries in the pool is very small).
90 Measured in jiffies(1).
91
92inet_peer_gc_mintime - INTEGER
93 Minimum interval between garbage collection passes. This interval is
94 in effect under high memory pressure on the pool.
95 Measured in jiffies(1).
96
97inet_peer_gc_maxtime - INTEGER
98 Minimum interval between garbage collection passes. This interval is
99 in effect under low (or absent) memory pressure on the pool.
100 Measured in jiffies(1).
101
102TCP variables:
103
Stephen Hemminger9772efb2005-11-10 17:09:53 -0800104tcp_abc - INTEGER
105 Controls Appropriate Byte Count defined in RFC3465. If set to
106 0 then does congestion avoid once per ack. 1 is conservative
107 value, and 2 is more agressive.
108
Linus Torvalds1da177e2005-04-16 15:20:36 -0700109tcp_syn_retries - INTEGER
110 Number of times initial SYNs for an active TCP connection attempt
111 will be retransmitted. Should not be higher than 255. Default value
112 is 5, which corresponds to ~180seconds.
113
114tcp_synack_retries - INTEGER
115 Number of times SYNACKs for a passive TCP connection attempt will
116 be retransmitted. Should not be higher than 255. Default value
117 is 5, which corresponds to ~180seconds.
118
119tcp_keepalive_time - INTEGER
120 How often TCP sends out keepalive messages when keepalive is enabled.
121 Default: 2hours.
122
123tcp_keepalive_probes - INTEGER
124 How many keepalive probes TCP sends out, until it decides that the
125 connection is broken. Default value: 9.
126
127tcp_keepalive_intvl - INTEGER
128 How frequently the probes are send out. Multiplied by
129 tcp_keepalive_probes it is time to kill not responding connection,
130 after probes started. Default value: 75sec i.e. connection
131 will be aborted after ~11 minutes of retries.
132
133tcp_retries1 - INTEGER
134 How many times to retry before deciding that something is wrong
135 and it is necessary to report this suspicion to network layer.
136 Minimal RFC value is 3, it is default, which corresponds
137 to ~3sec-8min depending on RTO.
138
139tcp_retries2 - INTEGER
140 How may times to retry before killing alive TCP connection.
141 RFC1122 says that the limit should be longer than 100 sec.
142 It is too small number. Default value 15 corresponds to ~13-30min
143 depending on RTO.
144
145tcp_orphan_retries - INTEGER
146 How may times to retry before killing TCP connection, closed
147 by our side. Default value 7 corresponds to ~50sec-16min
148 depending on RTO. If you machine is loaded WEB server,
149 you should think about lowering this value, such sockets
150 may consume significant resources. Cf. tcp_max_orphans.
151
152tcp_fin_timeout - INTEGER
153 Time to hold socket in state FIN-WAIT-2, if it was closed
154 by our side. Peer can be broken and never close its side,
155 or even died unexpectedly. Default value is 60sec.
156 Usual value used in 2.2 was 180 seconds, you may restore
157 it, but remember that if your machine is even underloaded WEB server,
158 you risk to overflow memory with kilotons of dead sockets,
159 FIN-WAIT-2 sockets are less dangerous than FIN-WAIT-1,
160 because they eat maximum 1.5K of memory, but they tend
161 to live longer. Cf. tcp_max_orphans.
162
163tcp_max_tw_buckets - INTEGER
164 Maximal number of timewait sockets held by system simultaneously.
165 If this number is exceeded time-wait socket is immediately destroyed
166 and warning is printed. This limit exists only to prevent
167 simple DoS attacks, you _must_ not lower the limit artificially,
168 but rather increase it (probably, after increasing installed memory),
169 if network conditions require more than default value.
170
171tcp_tw_recycle - BOOLEAN
172 Enable fast recycling TIME-WAIT sockets. Default value is 0.
173 It should not be changed without advice/request of technical
174 experts.
175
176tcp_tw_reuse - BOOLEAN
177 Allow to reuse TIME-WAIT sockets for new connections when it is
178 safe from protocol viewpoint. Default value is 0.
179 It should not be changed without advice/request of technical
180 experts.
181
182tcp_max_orphans - INTEGER
183 Maximal number of TCP sockets not attached to any user file handle,
184 held by system. If this number is exceeded orphaned connections are
185 reset immediately and warning is printed. This limit exists
186 only to prevent simple DoS attacks, you _must_ not rely on this
187 or lower the limit artificially, but rather increase it
188 (probably, after increasing installed memory),
189 if network conditions require more than default value,
190 and tune network services to linger and kill such states
191 more aggressively. Let me to remind again: each orphan eats
192 up to ~64K of unswappable memory.
193
194tcp_abort_on_overflow - BOOLEAN
195 If listening service is too slow to accept new connections,
196 reset them. Default state is FALSE. It means that if overflow
197 occurred due to a burst, connection will recover. Enable this
198 option _only_ if you are really sure that listening daemon
199 cannot be tuned to accept connections faster. Enabling this
200 option can harm clients of your server.
201
202tcp_syncookies - BOOLEAN
203 Only valid when the kernel was compiled with CONFIG_SYNCOOKIES
204 Send out syncookies when the syn backlog queue of a socket
205 overflows. This is to prevent against the common 'syn flood attack'
206 Default: FALSE
207
208 Note, that syncookies is fallback facility.
209 It MUST NOT be used to help highly loaded servers to stand
210 against legal connection rate. If you see synflood warnings
211 in your logs, but investigation shows that they occur
212 because of overload with legal connections, you should tune
213 another parameters until this warning disappear.
214 See: tcp_max_syn_backlog, tcp_synack_retries, tcp_abort_on_overflow.
215
216 syncookies seriously violate TCP protocol, do not allow
217 to use TCP extensions, can result in serious degradation
218 of some services (f.e. SMTP relaying), visible not by you,
219 but your clients and relays, contacting you. While you see
220 synflood warnings in logs not being really flooded, your server
221 is seriously misconfigured.
222
223tcp_stdurg - BOOLEAN
224 Use the Host requirements interpretation of the TCP urg pointer field.
225 Most hosts use the older BSD interpretation, so if you turn this on
226 Linux might not communicate correctly with them.
227 Default: FALSE
228
229tcp_max_syn_backlog - INTEGER
230 Maximal number of remembered connection requests, which are
231 still did not receive an acknowledgment from connecting client.
232 Default value is 1024 for systems with more than 128Mb of memory,
233 and 128 for low memory machines. If server suffers of overload,
234 try to increase this number.
235
236tcp_window_scaling - BOOLEAN
237 Enable window scaling as defined in RFC1323.
238
239tcp_timestamps - BOOLEAN
240 Enable timestamps as defined in RFC1323.
241
242tcp_sack - BOOLEAN
243 Enable select acknowledgments (SACKS).
244
245tcp_fack - BOOLEAN
246 Enable FACK congestion avoidance and fast retransmission.
247 The value is not used, if tcp_sack is not enabled.
248
249tcp_dsack - BOOLEAN
250 Allows TCP to send "duplicate" SACKs.
251
252tcp_ecn - BOOLEAN
253 Enable Explicit Congestion Notification in TCP.
254
255tcp_reordering - INTEGER
256 Maximal reordering of packets in a TCP stream.
257 Default: 3
258
259tcp_retrans_collapse - BOOLEAN
260 Bug-to-bug compatibility with some broken printers.
261 On retransmit try to send bigger packets to work around bugs in
262 certain TCP stacks.
263
264tcp_wmem - vector of 3 INTEGERs: min, default, max
265 min: Amount of memory reserved for send buffers for TCP socket.
266 Each TCP socket has rights to use it due to fact of its birth.
267 Default: 4K
268
269 default: Amount of memory allowed for send buffers for TCP socket
270 by default. This value overrides net.core.wmem_default used
271 by other protocols, it is usually lower than net.core.wmem_default.
272 Default: 16K
273
274 max: Maximal amount of memory allowed for automatically selected
275 send buffers for TCP socket. This value does not override
276 net.core.wmem_max, "static" selection via SO_SNDBUF does not use this.
277 Default: 128K
278
279tcp_rmem - vector of 3 INTEGERs: min, default, max
280 min: Minimal size of receive buffer used by TCP sockets.
281 It is guaranteed to each TCP socket, even under moderate memory
282 pressure.
283 Default: 8K
284
285 default: default size of receive buffer used by TCP sockets.
286 This value overrides net.core.rmem_default used by other protocols.
287 Default: 87380 bytes. This value results in window of 65535 with
288 default setting of tcp_adv_win_scale and tcp_app_win:0 and a bit
289 less for default tcp_app_win. See below about these variables.
290
291 max: maximal size of receive buffer allowed for automatically
292 selected receiver buffers for TCP socket. This value does not override
293 net.core.rmem_max, "static" selection via SO_RCVBUF does not use this.
294 Default: 87380*2 bytes.
295
296tcp_mem - vector of 3 INTEGERs: min, pressure, max
297 low: below this number of pages TCP is not bothered about its
298 memory appetite.
299
300 pressure: when amount of memory allocated by TCP exceeds this number
301 of pages, TCP moderates its memory consumption and enters memory
302 pressure mode, which is exited when memory consumption falls
303 under "low".
304
305 high: number of pages allowed for queueing by all TCP sockets.
306
307 Defaults are calculated at boot time from amount of available
308 memory.
309
310tcp_app_win - INTEGER
311 Reserve max(window/2^tcp_app_win, mss) of window for application
312 buffer. Value 0 is special, it means that nothing is reserved.
313 Default: 31
314
315tcp_adv_win_scale - INTEGER
316 Count buffering overhead as bytes/2^tcp_adv_win_scale
317 (if tcp_adv_win_scale > 0) or bytes-bytes/2^(-tcp_adv_win_scale),
318 if it is <= 0.
319 Default: 2
320
321tcp_rfc1337 - BOOLEAN
322 If set, the TCP stack behaves conforming to RFC1337. If unset,
323 we are not conforming to RFC, but prevent TCP TIME_WAIT
324 assassination.
325 Default: 0
326
327tcp_low_latency - BOOLEAN
328 If set, the TCP stack makes decisions that prefer lower
329 latency as opposed to higher throughput. By default, this
330 option is not set meaning that higher throughput is preferred.
331 An example of an application where this default should be
332 changed would be a Beowulf compute cluster.
333 Default: 0
334
Linus Torvalds1da177e2005-04-16 15:20:36 -0700335tcp_tso_win_divisor - INTEGER
336 This allows control over what percentage of the congestion window
337 can be consumed by a single TSO frame.
338 The setting of this parameter is a choice between burstiness and
339 building larger TSO frames.
Akinobu Mitae83b8602005-10-21 18:00:48 +0900340 Default: 3
Linus Torvalds1da177e2005-04-16 15:20:36 -0700341
342tcp_frto - BOOLEAN
343 Enables F-RTO, an enhanced recovery algorithm for TCP retransmission
344 timeouts. It is particularly beneficial in wireless environments
345 where packet loss is typically due to random radio interference
346 rather than intermediate router congestion.
347
Stephen Hemminger9d7bcfc2005-06-23 12:22:36 -0700348tcp_congestion_control - STRING
349 Set the congestion control algorithm to be used for new
350 connections. The algorithm "reno" is always available, but
351 additional choices may be available based on kernel configuration.
352
Linus Torvalds1da177e2005-04-16 15:20:36 -0700353somaxconn - INTEGER
354 Limit of socket listen() backlog, known in userspace as SOMAXCONN.
355 Defaults to 128. See also tcp_max_syn_backlog for additional tuning
356 for TCP sockets.
357
Rick Jones15d99e02006-03-20 22:40:29 -0800358tcp_workaround_signed_windows - BOOLEAN
359 If set, assume no receipt of a window scaling option means the
360 remote TCP is broken and treats the window as a signed quantity.
361 If unset, assume the remote TCP is not broken even if we do
362 not receive a window scaling option from them.
363 Default: 0
364
Linus Torvalds1da177e2005-04-16 15:20:36 -0700365IP Variables:
366
367ip_local_port_range - 2 INTEGERS
368 Defines the local port range that is used by TCP and UDP to
369 choose the local port. The first number is the first, the
370 second the last local port number. Default value depends on
371 amount of memory available on the system:
372 > 128Mb 32768-61000
373 < 128Mb 1024-4999 or even less.
374 This number defines number of active connections, which this
375 system can issue simultaneously to systems not supporting
376 TCP extensions (timestamps). With tcp_tw_recycle enabled
377 (i.e. by default) range 1024-4999 is enough to issue up to
378 2000 connections per second to systems supporting timestamps.
379
380ip_nonlocal_bind - BOOLEAN
381 If set, allows processes to bind() to non-local IP addresses,
382 which can be quite useful - but may break some applications.
383 Default: 0
384
385ip_dynaddr - BOOLEAN
386 If set non-zero, enables support for dynamic addresses.
387 If set to a non-zero value larger than 1, a kernel log
388 message will be printed when dynamic address rewriting
389 occurs.
390 Default: 0
391
392icmp_echo_ignore_all - BOOLEAN
David S. Miller7ce312462005-10-03 16:07:30 -0700393 If set non-zero, then the kernel will ignore all ICMP ECHO
394 requests sent to it.
395 Default: 0
396
Linus Torvalds1da177e2005-04-16 15:20:36 -0700397icmp_echo_ignore_broadcasts - BOOLEAN
David S. Miller7ce312462005-10-03 16:07:30 -0700398 If set non-zero, then the kernel will ignore all ICMP ECHO and
399 TIMESTAMP requests sent to it via broadcast/multicast.
400 Default: 1
Linus Torvalds1da177e2005-04-16 15:20:36 -0700401
402icmp_ratelimit - INTEGER
403 Limit the maximal rates for sending ICMP packets whose type matches
404 icmp_ratemask (see below) to specific targets.
405 0 to disable any limiting, otherwise the maximal rate in jiffies(1)
406 Default: 100
407
408icmp_ratemask - INTEGER
409 Mask made of ICMP types for which rates are being limited.
410 Significant bits: IHGFEDCBA9876543210
411 Default mask: 0000001100000011000 (6168)
412
413 Bit definitions (see include/linux/icmp.h):
414 0 Echo Reply
415 3 Destination Unreachable *
416 4 Source Quench *
417 5 Redirect
418 8 Echo Request
419 B Time Exceeded *
420 C Parameter Problem *
421 D Timestamp Request
422 E Timestamp Reply
423 F Info Request
424 G Info Reply
425 H Address Mask Request
426 I Address Mask Reply
427
428 * These are rate limited by default (see default mask above)
429
430icmp_ignore_bogus_error_responses - BOOLEAN
431 Some routers violate RFC1122 by sending bogus responses to broadcast
432 frames. Such violations are normally logged via a kernel warning.
433 If this is set to TRUE, the kernel will not give such warnings, which
434 will avoid log file clutter.
435 Default: FALSE
436
Horms95f7daf2006-02-02 17:02:25 -0800437icmp_errors_use_inbound_ifaddr - BOOLEAN
438
439 If zero, icmp error messages are sent with the primary address of
440 the exiting interface.
441
442 If non-zero, the message will be sent with the primary address of
443 the interface that received the packet that caused the icmp error.
444 This is the behaviour network many administrators will expect from
445 a router. And it can make debugging complicated network layouts
446 much easier.
447
448 Note that if no primary address exists for the interface selected,
449 then the primary address of the first non-loopback interface that
450 has one will be used regarldess of this setting.
451
452 Default: 0
453
Linus Torvalds1da177e2005-04-16 15:20:36 -0700454igmp_max_memberships - INTEGER
455 Change the maximum number of multicast groups we can subscribe to.
456 Default: 20
457
458conf/interface/* changes special settings per interface (where "interface" is
459 the name of your network interface)
460conf/all/* is special, changes the settings for all interfaces
461
462
463log_martians - BOOLEAN
464 Log packets with impossible addresses to kernel log.
465 log_martians for the interface will be enabled if at least one of
466 conf/{all,interface}/log_martians is set to TRUE,
467 it will be disabled otherwise
468
469accept_redirects - BOOLEAN
470 Accept ICMP redirect messages.
471 accept_redirects for the interface will be enabled if:
472 - both conf/{all,interface}/accept_redirects are TRUE in the case forwarding
473 for the interface is enabled
474 or
475 - at least one of conf/{all,interface}/accept_redirects is TRUE in the case
476 forwarding for the interface is disabled
477 accept_redirects for the interface will be disabled otherwise
478 default TRUE (host)
479 FALSE (router)
480
481forwarding - BOOLEAN
482 Enable IP forwarding on this interface.
483
484mc_forwarding - BOOLEAN
485 Do multicast routing. The kernel needs to be compiled with CONFIG_MROUTE
486 and a multicast routing daemon is required.
487 conf/all/mc_forwarding must also be set to TRUE to enable multicast routing
488 for the interface
489
490medium_id - INTEGER
491 Integer value used to differentiate the devices by the medium they
492 are attached to. Two devices can have different id values when
493 the broadcast packets are received only on one of them.
494 The default value 0 means that the device is the only interface
495 to its medium, value of -1 means that medium is not known.
496
497 Currently, it is used to change the proxy_arp behavior:
498 the proxy_arp feature is enabled for packets forwarded between
499 two devices attached to different media.
500
501proxy_arp - BOOLEAN
502 Do proxy arp.
503 proxy_arp for the interface will be enabled if at least one of
504 conf/{all,interface}/proxy_arp is set to TRUE,
505 it will be disabled otherwise
506
507shared_media - BOOLEAN
508 Send(router) or accept(host) RFC1620 shared media redirects.
509 Overrides ip_secure_redirects.
510 shared_media for the interface will be enabled if at least one of
511 conf/{all,interface}/shared_media is set to TRUE,
512 it will be disabled otherwise
513 default TRUE
514
515secure_redirects - BOOLEAN
516 Accept ICMP redirect messages only for gateways,
517 listed in default gateway list.
518 secure_redirects for the interface will be enabled if at least one of
519 conf/{all,interface}/secure_redirects is set to TRUE,
520 it will be disabled otherwise
521 default TRUE
522
523send_redirects - BOOLEAN
524 Send redirects, if router.
525 send_redirects for the interface will be enabled if at least one of
526 conf/{all,interface}/send_redirects is set to TRUE,
527 it will be disabled otherwise
528 Default: TRUE
529
530bootp_relay - BOOLEAN
531 Accept packets with source address 0.b.c.d destined
532 not to this host as local ones. It is supposed, that
533 BOOTP relay daemon will catch and forward such packets.
534 conf/all/bootp_relay must also be set to TRUE to enable BOOTP relay
535 for the interface
536 default FALSE
537 Not Implemented Yet.
538
539accept_source_route - BOOLEAN
540 Accept packets with SRR option.
541 conf/all/accept_source_route must also be set to TRUE to accept packets
542 with SRR option on the interface
543 default TRUE (router)
544 FALSE (host)
545
546rp_filter - BOOLEAN
547 1 - do source validation by reversed path, as specified in RFC1812
548 Recommended option for single homed hosts and stub network
549 routers. Could cause troubles for complicated (not loop free)
550 networks running a slow unreliable protocol (sort of RIP),
551 or using static routes.
552
553 0 - No source validation.
554
555 conf/all/rp_filter must also be set to TRUE to do source validation
556 on the interface
557
558 Default value is 0. Note that some distributions enable it
559 in startup scripts.
560
561arp_filter - BOOLEAN
562 1 - Allows you to have multiple network interfaces on the same
563 subnet, and have the ARPs for each interface be answered
564 based on whether or not the kernel would route a packet from
565 the ARP'd IP out that interface (therefore you must use source
566 based routing for this to work). In other words it allows control
567 of which cards (usually 1) will respond to an arp request.
568
569 0 - (default) The kernel can respond to arp requests with addresses
570 from other interfaces. This may seem wrong but it usually makes
571 sense, because it increases the chance of successful communication.
572 IP addresses are owned by the complete host on Linux, not by
573 particular interfaces. Only for more complex setups like load-
574 balancing, does this behaviour cause problems.
575
576 arp_filter for the interface will be enabled if at least one of
577 conf/{all,interface}/arp_filter is set to TRUE,
578 it will be disabled otherwise
579
580arp_announce - INTEGER
581 Define different restriction levels for announcing the local
582 source IP address from IP packets in ARP requests sent on
583 interface:
584 0 - (default) Use any local address, configured on any interface
585 1 - Try to avoid local addresses that are not in the target's
586 subnet for this interface. This mode is useful when target
587 hosts reachable via this interface require the source IP
588 address in ARP requests to be part of their logical network
589 configured on the receiving interface. When we generate the
590 request we will check all our subnets that include the
591 target IP and will preserve the source address if it is from
592 such subnet. If there is no such subnet we select source
593 address according to the rules for level 2.
594 2 - Always use the best local address for this target.
595 In this mode we ignore the source address in the IP packet
596 and try to select local address that we prefer for talks with
597 the target host. Such local address is selected by looking
598 for primary IP addresses on all our subnets on the outgoing
599 interface that include the target IP address. If no suitable
600 local address is found we select the first local address
601 we have on the outgoing interface or on all other interfaces,
602 with the hope we will receive reply for our request and
603 even sometimes no matter the source IP address we announce.
604
605 The max value from conf/{all,interface}/arp_announce is used.
606
607 Increasing the restriction level gives more chance for
608 receiving answer from the resolved target while decreasing
609 the level announces more valid sender's information.
610
611arp_ignore - INTEGER
612 Define different modes for sending replies in response to
613 received ARP requests that resolve local target IP addresses:
614 0 - (default): reply for any local target IP address, configured
615 on any interface
616 1 - reply only if the target IP address is local address
617 configured on the incoming interface
618 2 - reply only if the target IP address is local address
619 configured on the incoming interface and both with the
620 sender's IP address are part from same subnet on this interface
621 3 - do not reply for local addresses configured with scope host,
622 only resolutions for global and link addresses are replied
623 4-7 - reserved
624 8 - do not reply for all local addresses
625
626 The max value from conf/{all,interface}/arp_ignore is used
627 when ARP request is received on the {interface}
628
Neil Hormanc1b1bce2006-03-20 22:40:03 -0800629arp_accept - BOOLEAN
630 Define behavior when gratuitous arp replies are received:
631 0 - drop gratuitous arp frames
632 1 - accept gratuitous arp frames
633
Linus Torvalds1da177e2005-04-16 15:20:36 -0700634app_solicit - INTEGER
635 The maximum number of probes to send to the user space ARP daemon
636 via netlink before dropping back to multicast probes (see
637 mcast_solicit). Defaults to 0.
638
639disable_policy - BOOLEAN
640 Disable IPSEC policy (SPD) for this interface
641
642disable_xfrm - BOOLEAN
643 Disable IPSEC encryption on this interface, whatever the policy
644
645
646
647tag - INTEGER
648 Allows you to write a number, which can be used as required.
649 Default value is 0.
650
651(1) Jiffie: internal timeunit for the kernel. On the i386 1/100s, on the
652Alpha 1/1024s. See the HZ define in /usr/include/asm/param.h for the exact
653value on your system.
654
655Alexey Kuznetsov.
656kuznet@ms2.inr.ac.ru
657
658Updated by:
659Andi Kleen
660ak@muc.de
661Nicolas Delon
662delon.nicolas@wanadoo.fr
663
664
665
666
667/proc/sys/net/ipv6/* Variables:
668
669IPv6 has no global variables such as tcp_*. tcp_* settings under ipv4/ also
670apply to IPv6 [XXX?].
671
672bindv6only - BOOLEAN
673 Default value for IPV6_V6ONLY socket option,
674 which restricts use of the IPv6 socket to IPv6 communication
675 only.
676 TRUE: disable IPv4-mapped address feature
677 FALSE: enable IPv4-mapped address feature
678
679 Default: FALSE (as specified in RFC2553bis)
680
681IPv6 Fragmentation:
682
683ip6frag_high_thresh - INTEGER
684 Maximum memory used to reassemble IPv6 fragments. When
685 ip6frag_high_thresh bytes of memory is allocated for this purpose,
686 the fragment handler will toss packets until ip6frag_low_thresh
687 is reached.
688
689ip6frag_low_thresh - INTEGER
690 See ip6frag_high_thresh
691
692ip6frag_time - INTEGER
693 Time in seconds to keep an IPv6 fragment in memory.
694
695ip6frag_secret_interval - INTEGER
696 Regeneration interval (in seconds) of the hash secret (or lifetime
697 for the hash secret) for IPv6 fragments.
698 Default: 600
699
700conf/default/*:
701 Change the interface-specific default settings.
702
703
704conf/all/*:
705 Change all the interface-specific settings.
706
707 [XXX: Other special features than forwarding?]
708
709conf/all/forwarding - BOOLEAN
710 Enable global IPv6 forwarding between all interfaces.
711
712 IPv4 and IPv6 work differently here; e.g. netfilter must be used
713 to control which interfaces may forward packets and which not.
714
715 This also sets all interfaces' Host/Router setting
716 'forwarding' to the specified value. See below for details.
717
718 This referred to as global forwarding.
719
720conf/interface/*:
721 Change special settings per interface.
722
723 The functional behaviour for certain settings is different
724 depending on whether local forwarding is enabled or not.
725
726accept_ra - BOOLEAN
727 Accept Router Advertisements; autoconfigure using them.
728
729 Functional default: enabled if local forwarding is disabled.
730 disabled if local forwarding is enabled.
731
YOSHIFUJI Hideaki65f5c7c2006-03-20 16:55:08 -0800732accept_ra_defrtr - BOOLEAN
733 Learn default router in Router Advertisement.
734
735 Functional default: enabled if accept_ra is enabled.
736 disabled if accept_ra is disabled.
737
YOSHIFUJI Hideakic4fd30e2006-03-20 16:55:26 -0800738accept_ra_pinfo - BOOLEAN
739 Learn Prefix Inforamtion in Router Advertisement.
740
741 Functional default: enabled if accept_ra is enabled.
742 disabled if accept_ra is disabled.
743
YOSHIFUJI Hideaki09c884d2006-03-20 17:07:03 -0800744accept_ra_rt_info_max_plen - INTEGER
745 Maximum prefix length of Route Information in RA.
746
747 Route Information w/ prefix larger than or equal to this
748 variable shall be ignored.
749
750 Functional default: 0 if accept_ra_rtr_pref is enabled.
751 -1 if accept_ra_rtr_pref is disabled.
752
YOSHIFUJI Hideaki930d6ff2006-03-20 17:05:30 -0800753accept_ra_rtr_pref - BOOLEAN
754 Accept Router Preference in RA.
755
756 Functional default: enabled if accept_ra is enabled.
757 disabled if accept_ra is disabled.
758
Linus Torvalds1da177e2005-04-16 15:20:36 -0700759accept_redirects - BOOLEAN
760 Accept Redirects.
761
762 Functional default: enabled if local forwarding is disabled.
763 disabled if local forwarding is enabled.
764
765autoconf - BOOLEAN
766 Autoconfigure addresses using Prefix Information in Router
767 Advertisements.
768
YOSHIFUJI Hideakic4fd30e2006-03-20 16:55:26 -0800769 Functional default: enabled if accept_ra_pinfo is enabled.
770 disabled if accept_ra_pinfo is disabled.
Linus Torvalds1da177e2005-04-16 15:20:36 -0700771
772dad_transmits - INTEGER
773 The amount of Duplicate Address Detection probes to send.
774 Default: 1
775
776forwarding - BOOLEAN
777 Configure interface-specific Host/Router behaviour.
778
779 Note: It is recommended to have the same setting on all
780 interfaces; mixed router/host scenarios are rather uncommon.
781
782 FALSE:
783
784 By default, Host behaviour is assumed. This means:
785
786 1. IsRouter flag is not set in Neighbour Advertisements.
787 2. Router Solicitations are being sent when necessary.
788 3. If accept_ra is TRUE (default), accept Router
789 Advertisements (and do autoconfiguration).
790 4. If accept_redirects is TRUE (default), accept Redirects.
791
792 TRUE:
793
794 If local forwarding is enabled, Router behaviour is assumed.
795 This means exactly the reverse from the above:
796
797 1. IsRouter flag is set in Neighbour Advertisements.
798 2. Router Solicitations are not sent.
799 3. Router Advertisements are ignored.
800 4. Redirects are ignored.
801
802 Default: FALSE if global forwarding is disabled (default),
803 otherwise TRUE.
804
805hop_limit - INTEGER
806 Default Hop Limit to set.
807 Default: 64
808
809mtu - INTEGER
810 Default Maximum Transfer Unit
811 Default: 1280 (IPv6 required minimum)
812
YOSHIFUJI Hideaki52e16352006-03-20 17:05:47 -0800813router_probe_interval - INTEGER
814 Minimum interval (in seconds) between Router Probing described
815 in RFC4191.
816
817 Default: 60
818
Linus Torvalds1da177e2005-04-16 15:20:36 -0700819router_solicitation_delay - INTEGER
820 Number of seconds to wait after interface is brought up
821 before sending Router Solicitations.
822 Default: 1
823
824router_solicitation_interval - INTEGER
825 Number of seconds to wait between Router Solicitations.
826 Default: 4
827
828router_solicitations - INTEGER
829 Number of Router Solicitations to send until assuming no
830 routers are present.
831 Default: 3
832
833use_tempaddr - INTEGER
834 Preference for Privacy Extensions (RFC3041).
835 <= 0 : disable Privacy Extensions
836 == 1 : enable Privacy Extensions, but prefer public
837 addresses over temporary addresses.
838 > 1 : enable Privacy Extensions and prefer temporary
839 addresses over public addresses.
840 Default: 0 (for most devices)
841 -1 (for point-to-point devices and loopback devices)
842
843temp_valid_lft - INTEGER
844 valid lifetime (in seconds) for temporary addresses.
845 Default: 604800 (7 days)
846
847temp_prefered_lft - INTEGER
848 Preferred lifetime (in seconds) for temporary addresses.
849 Default: 86400 (1 day)
850
851max_desync_factor - INTEGER
852 Maximum value for DESYNC_FACTOR, which is a random value
853 that ensures that clients don't synchronize with each
854 other and generate new addresses at exactly the same time.
855 value is in seconds.
856 Default: 600
857
858regen_max_retry - INTEGER
859 Number of attempts before give up attempting to generate
860 valid temporary addresses.
861 Default: 5
862
863max_addresses - INTEGER
864 Number of maximum addresses per interface. 0 disables limitation.
865 It is recommended not set too large value (or 0) because it would
866 be too easy way to crash kernel to allow to create too much of
867 autoconfigured addresses.
868 Default: 16
869
870icmp/*:
871ratelimit - INTEGER
872 Limit the maximal rates for sending ICMPv6 packets.
873 0 to disable any limiting, otherwise the maximal rate in jiffies(1)
874 Default: 100
875
876
877IPv6 Update by:
878Pekka Savola <pekkas@netcore.fi>
879YOSHIFUJI Hideaki / USAGI Project <yoshfuji@linux-ipv6.org>
880
881
882/proc/sys/net/bridge/* Variables:
883
884bridge-nf-call-arptables - BOOLEAN
885 1 : pass bridged ARP traffic to arptables' FORWARD chain.
886 0 : disable this.
887 Default: 1
888
889bridge-nf-call-iptables - BOOLEAN
890 1 : pass bridged IPv4 traffic to iptables' chains.
891 0 : disable this.
892 Default: 1
893
894bridge-nf-call-ip6tables - BOOLEAN
895 1 : pass bridged IPv6 traffic to ip6tables' chains.
896 0 : disable this.
897 Default: 1
898
899bridge-nf-filter-vlan-tagged - BOOLEAN
900 1 : pass bridged vlan-tagged ARP/IP traffic to arptables/iptables.
901 0 : disable this.
902 Default: 1
903
904
905UNDOCUMENTED:
906
907dev_weight FIXME
908discovery_slots FIXME
909discovery_timeout FIXME
910fast_poll_increase FIXME
911ip6_queue_maxlen FIXME
912lap_keepalive_time FIXME
913lo_cong FIXME
914max_baud_rate FIXME
915max_dgram_qlen FIXME
916max_noreply_time FIXME
917max_tx_data_size FIXME
918max_tx_window FIXME
919min_tx_turn_time FIXME
920mod_cong FIXME
921no_cong FIXME
922no_cong_thresh FIXME
923slot_timeout FIXME
924warn_noreply_time FIXME
925
926$Id: ip-sysctl.txt,v 1.20 2001/12/13 09:00:18 davem Exp $