Jeff Garzik | 669a5db | 2006-08-29 18:12:40 -0400 | [diff] [blame] | 1 | /* |
| 2 | * Libata driver for the highpoint 372N and 302N UDMA66 ATA controllers. |
| 3 | * |
| 4 | * This driver is heavily based upon: |
| 5 | * |
| 6 | * linux/drivers/ide/pci/hpt366.c Version 0.36 April 25, 2003 |
| 7 | * |
| 8 | * Copyright (C) 1999-2003 Andre Hedrick <andre@linux-ide.org> |
| 9 | * Portions Copyright (C) 2001 Sun Microsystems, Inc. |
| 10 | * Portions Copyright (C) 2003 Red Hat Inc |
| 11 | * |
| 12 | * |
| 13 | * TODO |
| 14 | * 371N |
| 15 | * Work out best PLL policy |
| 16 | */ |
| 17 | |
| 18 | #include <linux/kernel.h> |
| 19 | #include <linux/module.h> |
| 20 | #include <linux/pci.h> |
| 21 | #include <linux/init.h> |
| 22 | #include <linux/blkdev.h> |
| 23 | #include <linux/delay.h> |
| 24 | #include <scsi/scsi_host.h> |
| 25 | #include <linux/libata.h> |
| 26 | |
| 27 | #define DRV_NAME "pata_hpt3x2n" |
| 28 | #define DRV_VERSION "0.3" |
| 29 | |
| 30 | enum { |
| 31 | HPT_PCI_FAST = (1 << 31), |
| 32 | PCI66 = (1 << 1), |
| 33 | USE_DPLL = (1 << 0) |
| 34 | }; |
| 35 | |
| 36 | struct hpt_clock { |
| 37 | u8 xfer_speed; |
| 38 | u32 timing; |
| 39 | }; |
| 40 | |
| 41 | struct hpt_chip { |
| 42 | const char *name; |
| 43 | struct hpt_clock *clocks[3]; |
| 44 | }; |
| 45 | |
| 46 | /* key for bus clock timings |
| 47 | * bit |
| 48 | * 0:3 data_high_time. inactive time of DIOW_/DIOR_ for PIO and MW |
| 49 | * DMA. cycles = value + 1 |
| 50 | * 4:8 data_low_time. active time of DIOW_/DIOR_ for PIO and MW |
| 51 | * DMA. cycles = value + 1 |
| 52 | * 9:12 cmd_high_time. inactive time of DIOW_/DIOR_ during task file |
| 53 | * register access. |
| 54 | * 13:17 cmd_low_time. active time of DIOW_/DIOR_ during task file |
| 55 | * register access. |
| 56 | * 18:21 udma_cycle_time. clock freq and clock cycles for UDMA xfer. |
| 57 | * during task file register access. |
| 58 | * 22:24 pre_high_time. time to initialize 1st cycle for PIO and MW DMA |
| 59 | * xfer. |
| 60 | * 25:27 cmd_pre_high_time. time to initialize 1st PIO cycle for task |
| 61 | * register access. |
| 62 | * 28 UDMA enable |
| 63 | * 29 DMA enable |
| 64 | * 30 PIO_MST enable. if set, the chip is in bus master mode during |
| 65 | * PIO. |
| 66 | * 31 FIFO enable. |
| 67 | */ |
Jeff Garzik | 85cd725 | 2006-08-31 00:03:49 -0400 | [diff] [blame] | 68 | |
Jeff Garzik | 669a5db | 2006-08-29 18:12:40 -0400 | [diff] [blame] | 69 | /* 66MHz DPLL clocks */ |
| 70 | |
| 71 | static struct hpt_clock hpt3x2n_clocks[] = { |
| 72 | { XFER_UDMA_7, 0x1c869c62 }, |
| 73 | { XFER_UDMA_6, 0x1c869c62 }, |
| 74 | { XFER_UDMA_5, 0x1c8a9c62 }, |
| 75 | { XFER_UDMA_4, 0x1c8a9c62 }, |
| 76 | { XFER_UDMA_3, 0x1c8e9c62 }, |
| 77 | { XFER_UDMA_2, 0x1c929c62 }, |
| 78 | { XFER_UDMA_1, 0x1c9a9c62 }, |
| 79 | { XFER_UDMA_0, 0x1c829c62 }, |
| 80 | |
| 81 | { XFER_MW_DMA_2, 0x2c829c62 }, |
| 82 | { XFER_MW_DMA_1, 0x2c829c66 }, |
| 83 | { XFER_MW_DMA_0, 0x2c829d2c }, |
| 84 | |
| 85 | { XFER_PIO_4, 0x0c829c62 }, |
| 86 | { XFER_PIO_3, 0x0c829c84 }, |
| 87 | { XFER_PIO_2, 0x0c829ca6 }, |
| 88 | { XFER_PIO_1, 0x0d029d26 }, |
| 89 | { XFER_PIO_0, 0x0d029d5e }, |
| 90 | { 0, 0x0d029d5e } |
| 91 | }; |
| 92 | |
| 93 | /** |
| 94 | * hpt3x2n_find_mode - reset the hpt3x2n bus |
| 95 | * @ap: ATA port |
| 96 | * @speed: transfer mode |
| 97 | * |
| 98 | * Return the 32bit register programming information for this channel |
| 99 | * that matches the speed provided. For the moment the clocks table |
| 100 | * is hard coded but easy to change. This will be needed if we use |
| 101 | * different DPLLs |
| 102 | */ |
Jeff Garzik | 85cd725 | 2006-08-31 00:03:49 -0400 | [diff] [blame] | 103 | |
Jeff Garzik | 669a5db | 2006-08-29 18:12:40 -0400 | [diff] [blame] | 104 | static u32 hpt3x2n_find_mode(struct ata_port *ap, int speed) |
| 105 | { |
| 106 | struct hpt_clock *clocks = hpt3x2n_clocks; |
Jeff Garzik | 85cd725 | 2006-08-31 00:03:49 -0400 | [diff] [blame] | 107 | |
Jeff Garzik | 669a5db | 2006-08-29 18:12:40 -0400 | [diff] [blame] | 108 | while(clocks->xfer_speed) { |
| 109 | if (clocks->xfer_speed == speed) |
| 110 | return clocks->timing; |
| 111 | clocks++; |
| 112 | } |
| 113 | BUG(); |
| 114 | return 0xffffffffU; /* silence compiler warning */ |
| 115 | } |
| 116 | |
| 117 | /** |
| 118 | * hpt3x2n_pre_reset - reset the hpt3x2n bus |
| 119 | * @ap: ATA port to reset |
| 120 | * |
| 121 | * Perform the initial reset handling for the 3x2n series controllers. |
| 122 | * Reset the hardware and state machine, obtain the cable type. |
| 123 | */ |
Jeff Garzik | 85cd725 | 2006-08-31 00:03:49 -0400 | [diff] [blame] | 124 | |
Jeff Garzik | 669a5db | 2006-08-29 18:12:40 -0400 | [diff] [blame] | 125 | static int hpt3xn_pre_reset(struct ata_port *ap) |
| 126 | { |
| 127 | u8 scr2, ata66; |
| 128 | struct pci_dev *pdev = to_pci_dev(ap->host->dev); |
Jeff Garzik | 85cd725 | 2006-08-31 00:03:49 -0400 | [diff] [blame] | 129 | |
Jeff Garzik | 669a5db | 2006-08-29 18:12:40 -0400 | [diff] [blame] | 130 | pci_read_config_byte(pdev, 0x5B, &scr2); |
| 131 | pci_write_config_byte(pdev, 0x5B, scr2 & ~0x01); |
| 132 | /* Cable register now active */ |
| 133 | pci_read_config_byte(pdev, 0x5A, &ata66); |
| 134 | /* Restore state */ |
| 135 | pci_write_config_byte(pdev, 0x5B, scr2); |
Jeff Garzik | 85cd725 | 2006-08-31 00:03:49 -0400 | [diff] [blame] | 136 | |
Jeff Garzik | 669a5db | 2006-08-29 18:12:40 -0400 | [diff] [blame] | 137 | if (ata66 & (1 << ap->port_no)) |
| 138 | ap->cbl = ATA_CBL_PATA40; |
| 139 | else |
| 140 | ap->cbl = ATA_CBL_PATA80; |
| 141 | |
| 142 | /* Reset the state machine */ |
Jeff Garzik | 85cd725 | 2006-08-31 00:03:49 -0400 | [diff] [blame] | 143 | pci_write_config_byte(pdev, 0x50, 0x37); |
| 144 | pci_write_config_byte(pdev, 0x54, 0x37); |
Jeff Garzik | 669a5db | 2006-08-29 18:12:40 -0400 | [diff] [blame] | 145 | udelay(100); |
| 146 | |
| 147 | return ata_std_prereset(ap); |
| 148 | } |
Jeff Garzik | 85cd725 | 2006-08-31 00:03:49 -0400 | [diff] [blame] | 149 | |
Jeff Garzik | 669a5db | 2006-08-29 18:12:40 -0400 | [diff] [blame] | 150 | /** |
| 151 | * hpt3x2n_error_handler - probe the hpt3x2n bus |
| 152 | * @ap: ATA port to reset |
| 153 | * |
| 154 | * Perform the probe reset handling for the 3x2N |
| 155 | */ |
Jeff Garzik | 85cd725 | 2006-08-31 00:03:49 -0400 | [diff] [blame] | 156 | |
Jeff Garzik | 669a5db | 2006-08-29 18:12:40 -0400 | [diff] [blame] | 157 | static void hpt3x2n_error_handler(struct ata_port *ap) |
| 158 | { |
| 159 | ata_bmdma_drive_eh(ap, hpt3xn_pre_reset, ata_std_softreset, NULL, ata_std_postreset); |
| 160 | } |
Jeff Garzik | 85cd725 | 2006-08-31 00:03:49 -0400 | [diff] [blame] | 161 | |
Jeff Garzik | 669a5db | 2006-08-29 18:12:40 -0400 | [diff] [blame] | 162 | /** |
| 163 | * hpt3x2n_set_piomode - PIO setup |
| 164 | * @ap: ATA interface |
| 165 | * @adev: device on the interface |
| 166 | * |
Jeff Garzik | 85cd725 | 2006-08-31 00:03:49 -0400 | [diff] [blame] | 167 | * Perform PIO mode setup. |
Jeff Garzik | 669a5db | 2006-08-29 18:12:40 -0400 | [diff] [blame] | 168 | */ |
Jeff Garzik | 85cd725 | 2006-08-31 00:03:49 -0400 | [diff] [blame] | 169 | |
Jeff Garzik | 669a5db | 2006-08-29 18:12:40 -0400 | [diff] [blame] | 170 | static void hpt3x2n_set_piomode(struct ata_port *ap, struct ata_device *adev) |
| 171 | { |
| 172 | struct pci_dev *pdev = to_pci_dev(ap->host->dev); |
| 173 | u32 addr1, addr2; |
| 174 | u32 reg; |
| 175 | u32 mode; |
| 176 | u8 fast; |
| 177 | |
| 178 | addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no); |
| 179 | addr2 = 0x51 + 4 * ap->port_no; |
Jeff Garzik | 85cd725 | 2006-08-31 00:03:49 -0400 | [diff] [blame] | 180 | |
Jeff Garzik | 669a5db | 2006-08-29 18:12:40 -0400 | [diff] [blame] | 181 | /* Fast interrupt prediction disable, hold off interrupt disable */ |
| 182 | pci_read_config_byte(pdev, addr2, &fast); |
| 183 | fast &= ~0x07; |
| 184 | pci_write_config_byte(pdev, addr2, fast); |
Jeff Garzik | 85cd725 | 2006-08-31 00:03:49 -0400 | [diff] [blame] | 185 | |
Jeff Garzik | 669a5db | 2006-08-29 18:12:40 -0400 | [diff] [blame] | 186 | pci_read_config_dword(pdev, addr1, ®); |
| 187 | mode = hpt3x2n_find_mode(ap, adev->pio_mode); |
| 188 | mode &= ~0x8000000; /* No FIFO in PIO */ |
| 189 | mode &= ~0x30070000; /* Leave config bits alone */ |
| 190 | reg &= 0x30070000; /* Strip timing bits */ |
| 191 | pci_write_config_dword(pdev, addr1, reg | mode); |
| 192 | } |
| 193 | |
| 194 | /** |
| 195 | * hpt3x2n_set_dmamode - DMA timing setup |
| 196 | * @ap: ATA interface |
| 197 | * @adev: Device being configured |
| 198 | * |
| 199 | * Set up the channel for MWDMA or UDMA modes. Much the same as with |
| 200 | * PIO, load the mode number and then set MWDMA or UDMA flag. |
| 201 | */ |
Jeff Garzik | 85cd725 | 2006-08-31 00:03:49 -0400 | [diff] [blame] | 202 | |
Jeff Garzik | 669a5db | 2006-08-29 18:12:40 -0400 | [diff] [blame] | 203 | static void hpt3x2n_set_dmamode(struct ata_port *ap, struct ata_device *adev) |
| 204 | { |
| 205 | struct pci_dev *pdev = to_pci_dev(ap->host->dev); |
| 206 | u32 addr1, addr2; |
| 207 | u32 reg; |
| 208 | u32 mode; |
| 209 | u8 fast; |
| 210 | |
| 211 | addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no); |
| 212 | addr2 = 0x51 + 4 * ap->port_no; |
Jeff Garzik | 85cd725 | 2006-08-31 00:03:49 -0400 | [diff] [blame] | 213 | |
Jeff Garzik | 669a5db | 2006-08-29 18:12:40 -0400 | [diff] [blame] | 214 | /* Fast interrupt prediction disable, hold off interrupt disable */ |
| 215 | pci_read_config_byte(pdev, addr2, &fast); |
| 216 | fast &= ~0x07; |
| 217 | pci_write_config_byte(pdev, addr2, fast); |
Jeff Garzik | 85cd725 | 2006-08-31 00:03:49 -0400 | [diff] [blame] | 218 | |
Jeff Garzik | 669a5db | 2006-08-29 18:12:40 -0400 | [diff] [blame] | 219 | pci_read_config_dword(pdev, addr1, ®); |
| 220 | mode = hpt3x2n_find_mode(ap, adev->dma_mode); |
| 221 | mode |= 0x8000000; /* FIFO in MWDMA or UDMA */ |
| 222 | mode &= ~0xC0000000; /* Leave config bits alone */ |
| 223 | reg &= 0xC0000000; /* Strip timing bits */ |
| 224 | pci_write_config_dword(pdev, addr1, reg | mode); |
| 225 | } |
| 226 | |
| 227 | /** |
| 228 | * hpt3x2n_bmdma_end - DMA engine stop |
| 229 | * @qc: ATA command |
| 230 | * |
| 231 | * Clean up after the HPT3x2n and later DMA engine |
| 232 | */ |
Jeff Garzik | 85cd725 | 2006-08-31 00:03:49 -0400 | [diff] [blame] | 233 | |
Jeff Garzik | 669a5db | 2006-08-29 18:12:40 -0400 | [diff] [blame] | 234 | static void hpt3x2n_bmdma_stop(struct ata_queued_cmd *qc) |
| 235 | { |
| 236 | struct ata_port *ap = qc->ap; |
| 237 | struct pci_dev *pdev = to_pci_dev(ap->host->dev); |
| 238 | int mscreg = 0x50 + 2 * ap->port_no; |
| 239 | u8 bwsr_stat, msc_stat; |
Jeff Garzik | 85cd725 | 2006-08-31 00:03:49 -0400 | [diff] [blame] | 240 | |
Jeff Garzik | 669a5db | 2006-08-29 18:12:40 -0400 | [diff] [blame] | 241 | pci_read_config_byte(pdev, 0x6A, &bwsr_stat); |
| 242 | pci_read_config_byte(pdev, mscreg, &msc_stat); |
| 243 | if (bwsr_stat & (1 << ap->port_no)) |
| 244 | pci_write_config_byte(pdev, mscreg, msc_stat | 0x30); |
| 245 | ata_bmdma_stop(qc); |
| 246 | } |
| 247 | |
| 248 | /** |
| 249 | * hpt3x2n_set_clock - clock control |
| 250 | * @ap: ATA port |
| 251 | * @source: 0x21 or 0x23 for PLL or PCI sourced clock |
| 252 | * |
| 253 | * Switch the ATA bus clock between the PLL and PCI clock sources |
| 254 | * while correctly isolating the bus and resetting internal logic |
| 255 | * |
| 256 | * We must use the DPLL for |
| 257 | * - writing |
| 258 | * - second channel UDMA7 (SATA ports) or higher |
| 259 | * - 66MHz PCI |
Jeff Garzik | 85cd725 | 2006-08-31 00:03:49 -0400 | [diff] [blame] | 260 | * |
Jeff Garzik | 669a5db | 2006-08-29 18:12:40 -0400 | [diff] [blame] | 261 | * or we will underclock the device and get reduced performance. |
| 262 | */ |
Jeff Garzik | 85cd725 | 2006-08-31 00:03:49 -0400 | [diff] [blame] | 263 | |
Jeff Garzik | 669a5db | 2006-08-29 18:12:40 -0400 | [diff] [blame] | 264 | static void hpt3x2n_set_clock(struct ata_port *ap, int source) |
| 265 | { |
| 266 | unsigned long bmdma = ap->ioaddr.bmdma_addr; |
Jeff Garzik | 85cd725 | 2006-08-31 00:03:49 -0400 | [diff] [blame] | 267 | |
Jeff Garzik | 669a5db | 2006-08-29 18:12:40 -0400 | [diff] [blame] | 268 | /* Tristate the bus */ |
| 269 | outb(0x80, bmdma+0x73); |
| 270 | outb(0x80, bmdma+0x77); |
Jeff Garzik | 85cd725 | 2006-08-31 00:03:49 -0400 | [diff] [blame] | 271 | |
Jeff Garzik | 669a5db | 2006-08-29 18:12:40 -0400 | [diff] [blame] | 272 | /* Switch clock and reset channels */ |
| 273 | outb(source, bmdma+0x7B); |
| 274 | outb(0xC0, bmdma+0x79); |
Jeff Garzik | 85cd725 | 2006-08-31 00:03:49 -0400 | [diff] [blame] | 275 | |
Jeff Garzik | 669a5db | 2006-08-29 18:12:40 -0400 | [diff] [blame] | 276 | /* Reset state machines */ |
| 277 | outb(0x37, bmdma+0x70); |
| 278 | outb(0x37, bmdma+0x74); |
Jeff Garzik | 85cd725 | 2006-08-31 00:03:49 -0400 | [diff] [blame] | 279 | |
Jeff Garzik | 669a5db | 2006-08-29 18:12:40 -0400 | [diff] [blame] | 280 | /* Complete reset */ |
| 281 | outb(0x00, bmdma+0x79); |
Jeff Garzik | 85cd725 | 2006-08-31 00:03:49 -0400 | [diff] [blame] | 282 | |
Jeff Garzik | 669a5db | 2006-08-29 18:12:40 -0400 | [diff] [blame] | 283 | /* Reconnect channels to bus */ |
| 284 | outb(0x00, bmdma+0x73); |
| 285 | outb(0x00, bmdma+0x77); |
| 286 | } |
| 287 | |
| 288 | /* Check if our partner interface is busy */ |
| 289 | |
| 290 | static int hpt3x2n_pair_idle(struct ata_port *ap) |
| 291 | { |
| 292 | struct ata_host *host = ap->host; |
| 293 | struct ata_port *pair = host->ports[ap->port_no ^ 1]; |
Jeff Garzik | 85cd725 | 2006-08-31 00:03:49 -0400 | [diff] [blame] | 294 | |
Jeff Garzik | 669a5db | 2006-08-29 18:12:40 -0400 | [diff] [blame] | 295 | if (pair->hsm_task_state == HSM_ST_IDLE) |
| 296 | return 1; |
| 297 | return 0; |
| 298 | } |
| 299 | |
| 300 | static int hpt3x2n_use_dpll(struct ata_port *ap, int reading) |
| 301 | { |
| 302 | long flags = (long)ap->host->private_data; |
| 303 | /* See if we should use the DPLL */ |
| 304 | if (reading == 0) |
| 305 | return USE_DPLL; /* Needed for write */ |
| 306 | if (flags & PCI66) |
| 307 | return USE_DPLL; /* Needed at 66Mhz */ |
Jeff Garzik | 85cd725 | 2006-08-31 00:03:49 -0400 | [diff] [blame] | 308 | return 0; |
Jeff Garzik | 669a5db | 2006-08-29 18:12:40 -0400 | [diff] [blame] | 309 | } |
| 310 | |
| 311 | static unsigned int hpt3x2n_qc_issue_prot(struct ata_queued_cmd *qc) |
| 312 | { |
| 313 | struct ata_taskfile *tf = &qc->tf; |
| 314 | struct ata_port *ap = qc->ap; |
| 315 | int flags = (long)ap->host->private_data; |
Jeff Garzik | 85cd725 | 2006-08-31 00:03:49 -0400 | [diff] [blame] | 316 | |
Jeff Garzik | 669a5db | 2006-08-29 18:12:40 -0400 | [diff] [blame] | 317 | if (hpt3x2n_pair_idle(ap)) { |
| 318 | int dpll = hpt3x2n_use_dpll(ap, (tf->flags & ATA_TFLAG_WRITE)); |
| 319 | if ((flags & USE_DPLL) != dpll) { |
| 320 | if (dpll == 1) |
| 321 | hpt3x2n_set_clock(ap, 0x21); |
| 322 | else |
| 323 | hpt3x2n_set_clock(ap, 0x23); |
| 324 | } |
| 325 | } |
| 326 | return ata_qc_issue_prot(qc); |
| 327 | } |
| 328 | |
| 329 | static struct scsi_host_template hpt3x2n_sht = { |
| 330 | .module = THIS_MODULE, |
| 331 | .name = DRV_NAME, |
| 332 | .ioctl = ata_scsi_ioctl, |
| 333 | .queuecommand = ata_scsi_queuecmd, |
| 334 | .can_queue = ATA_DEF_QUEUE, |
| 335 | .this_id = ATA_SHT_THIS_ID, |
| 336 | .sg_tablesize = LIBATA_MAX_PRD, |
Jeff Garzik | 669a5db | 2006-08-29 18:12:40 -0400 | [diff] [blame] | 337 | .cmd_per_lun = ATA_SHT_CMD_PER_LUN, |
| 338 | .emulated = ATA_SHT_EMULATED, |
| 339 | .use_clustering = ATA_SHT_USE_CLUSTERING, |
| 340 | .proc_name = DRV_NAME, |
| 341 | .dma_boundary = ATA_DMA_BOUNDARY, |
| 342 | .slave_configure = ata_scsi_slave_config, |
Tejun Heo | afdfe89 | 2006-11-29 11:26:47 +0900 | [diff] [blame] | 343 | .slave_destroy = ata_scsi_slave_destroy, |
Jeff Garzik | 669a5db | 2006-08-29 18:12:40 -0400 | [diff] [blame] | 344 | .bios_param = ata_std_bios_param, |
| 345 | }; |
| 346 | |
| 347 | /* |
| 348 | * Configuration for HPT3x2n. |
| 349 | */ |
Jeff Garzik | 85cd725 | 2006-08-31 00:03:49 -0400 | [diff] [blame] | 350 | |
Jeff Garzik | 669a5db | 2006-08-29 18:12:40 -0400 | [diff] [blame] | 351 | static struct ata_port_operations hpt3x2n_port_ops = { |
| 352 | .port_disable = ata_port_disable, |
| 353 | .set_piomode = hpt3x2n_set_piomode, |
| 354 | .set_dmamode = hpt3x2n_set_dmamode, |
| 355 | .mode_filter = ata_pci_default_filter, |
Jeff Garzik | 85cd725 | 2006-08-31 00:03:49 -0400 | [diff] [blame] | 356 | |
Jeff Garzik | 669a5db | 2006-08-29 18:12:40 -0400 | [diff] [blame] | 357 | .tf_load = ata_tf_load, |
| 358 | .tf_read = ata_tf_read, |
| 359 | .check_status = ata_check_status, |
| 360 | .exec_command = ata_exec_command, |
| 361 | .dev_select = ata_std_dev_select, |
| 362 | |
| 363 | .freeze = ata_bmdma_freeze, |
| 364 | .thaw = ata_bmdma_thaw, |
| 365 | .error_handler = hpt3x2n_error_handler, |
| 366 | .post_internal_cmd = ata_bmdma_post_internal_cmd, |
| 367 | |
| 368 | .bmdma_setup = ata_bmdma_setup, |
| 369 | .bmdma_start = ata_bmdma_start, |
| 370 | .bmdma_stop = hpt3x2n_bmdma_stop, |
| 371 | .bmdma_status = ata_bmdma_status, |
| 372 | |
| 373 | .qc_prep = ata_qc_prep, |
| 374 | .qc_issue = hpt3x2n_qc_issue_prot, |
Jeff Garzik | bda3028 | 2006-09-27 05:41:13 -0400 | [diff] [blame] | 375 | |
Jeff Garzik | 669a5db | 2006-08-29 18:12:40 -0400 | [diff] [blame] | 376 | .data_xfer = ata_pio_data_xfer, |
| 377 | |
| 378 | .irq_handler = ata_interrupt, |
| 379 | .irq_clear = ata_bmdma_irq_clear, |
| 380 | |
| 381 | .port_start = ata_port_start, |
| 382 | .port_stop = ata_port_stop, |
| 383 | .host_stop = ata_host_stop |
Jeff Garzik | 85cd725 | 2006-08-31 00:03:49 -0400 | [diff] [blame] | 384 | }; |
Jeff Garzik | 669a5db | 2006-08-29 18:12:40 -0400 | [diff] [blame] | 385 | |
| 386 | /** |
| 387 | * hpt3xn_calibrate_dpll - Calibrate the DPLL loop |
Jeff Garzik | 85cd725 | 2006-08-31 00:03:49 -0400 | [diff] [blame] | 388 | * @dev: PCI device |
Jeff Garzik | 669a5db | 2006-08-29 18:12:40 -0400 | [diff] [blame] | 389 | * |
| 390 | * Perform a calibration cycle on the HPT3xN DPLL. Returns 1 if this |
| 391 | * succeeds |
| 392 | */ |
| 393 | |
| 394 | static int hpt3xn_calibrate_dpll(struct pci_dev *dev) |
| 395 | { |
| 396 | u8 reg5b; |
| 397 | u32 reg5c; |
| 398 | int tries; |
Jeff Garzik | 85cd725 | 2006-08-31 00:03:49 -0400 | [diff] [blame] | 399 | |
Jeff Garzik | 669a5db | 2006-08-29 18:12:40 -0400 | [diff] [blame] | 400 | for(tries = 0; tries < 0x5000; tries++) { |
| 401 | udelay(50); |
| 402 | pci_read_config_byte(dev, 0x5b, ®5b); |
| 403 | if (reg5b & 0x80) { |
| 404 | /* See if it stays set */ |
| 405 | for(tries = 0; tries < 0x1000; tries ++) { |
| 406 | pci_read_config_byte(dev, 0x5b, ®5b); |
| 407 | /* Failed ? */ |
| 408 | if ((reg5b & 0x80) == 0) |
| 409 | return 0; |
| 410 | } |
| 411 | /* Turn off tuning, we have the DPLL set */ |
| 412 | pci_read_config_dword(dev, 0x5c, ®5c); |
| 413 | pci_write_config_dword(dev, 0x5c, reg5c & ~ 0x100); |
| 414 | return 1; |
| 415 | } |
| 416 | } |
| 417 | /* Never went stable */ |
| 418 | return 0; |
| 419 | } |
| 420 | |
| 421 | static int hpt3x2n_pci_clock(struct pci_dev *pdev) |
| 422 | { |
| 423 | unsigned long freq; |
| 424 | u32 fcnt; |
Jeff Garzik | 85cd725 | 2006-08-31 00:03:49 -0400 | [diff] [blame] | 425 | |
Jeff Garzik | 669a5db | 2006-08-29 18:12:40 -0400 | [diff] [blame] | 426 | pci_read_config_dword(pdev, 0x70/*CHECKME*/, &fcnt); |
| 427 | if ((fcnt >> 12) != 0xABCDE) { |
| 428 | printk(KERN_WARNING "hpt3xn: BIOS clock data not set.\n"); |
| 429 | return 33; /* Not BIOS set */ |
| 430 | } |
| 431 | fcnt &= 0x1FF; |
Jeff Garzik | 85cd725 | 2006-08-31 00:03:49 -0400 | [diff] [blame] | 432 | |
Jeff Garzik | 669a5db | 2006-08-29 18:12:40 -0400 | [diff] [blame] | 433 | freq = (fcnt * 77) / 192; |
Jeff Garzik | 85cd725 | 2006-08-31 00:03:49 -0400 | [diff] [blame] | 434 | |
Jeff Garzik | 669a5db | 2006-08-29 18:12:40 -0400 | [diff] [blame] | 435 | /* Clamp to bands */ |
| 436 | if (freq < 40) |
| 437 | return 33; |
| 438 | if (freq < 45) |
| 439 | return 40; |
| 440 | if (freq < 55) |
| 441 | return 50; |
| 442 | return 66; |
| 443 | } |
| 444 | |
| 445 | /** |
| 446 | * hpt3x2n_init_one - Initialise an HPT37X/302 |
| 447 | * @dev: PCI device |
| 448 | * @id: Entry in match table |
| 449 | * |
| 450 | * Initialise an HPT3x2n device. There are some interesting complications |
| 451 | * here. Firstly the chip may report 366 and be one of several variants. |
| 452 | * Secondly all the timings depend on the clock for the chip which we must |
| 453 | * detect and look up |
| 454 | * |
| 455 | * This is the known chip mappings. It may be missing a couple of later |
| 456 | * releases. |
| 457 | * |
| 458 | * Chip version PCI Rev Notes |
| 459 | * HPT372 4 (HPT366) 5 Other driver |
| 460 | * HPT372N 4 (HPT366) 6 UDMA133 |
| 461 | * HPT372 5 (HPT372) 1 Other driver |
| 462 | * HPT372N 5 (HPT372) 2 UDMA133 |
| 463 | * HPT302 6 (HPT302) * Other driver |
| 464 | * HPT302N 6 (HPT302) > 1 UDMA133 |
| 465 | * HPT371 7 (HPT371) * Other driver |
| 466 | * HPT371N 7 (HPT371) > 1 UDMA133 |
| 467 | * HPT374 8 (HPT374) * Other driver |
| 468 | * HPT372N 9 (HPT372N) * UDMA133 |
| 469 | * |
| 470 | * (1) UDMA133 support depends on the bus clock |
| 471 | * |
| 472 | * To pin down HPT371N |
| 473 | */ |
Jeff Garzik | 85cd725 | 2006-08-31 00:03:49 -0400 | [diff] [blame] | 474 | |
Jeff Garzik | 669a5db | 2006-08-29 18:12:40 -0400 | [diff] [blame] | 475 | static int hpt3x2n_init_one(struct pci_dev *dev, const struct pci_device_id *id) |
| 476 | { |
| 477 | /* HPT372N and friends - UDMA133 */ |
| 478 | static struct ata_port_info info = { |
| 479 | .sht = &hpt3x2n_sht, |
| 480 | .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST, |
| 481 | .pio_mask = 0x1f, |
| 482 | .mwdma_mask = 0x07, |
| 483 | .udma_mask = 0x7f, |
| 484 | .port_ops = &hpt3x2n_port_ops |
| 485 | }; |
| 486 | struct ata_port_info *port_info[2]; |
| 487 | struct ata_port_info *port = &info; |
| 488 | |
| 489 | u8 irqmask; |
| 490 | u32 class_rev; |
Jeff Garzik | 85cd725 | 2006-08-31 00:03:49 -0400 | [diff] [blame] | 491 | |
Jeff Garzik | 669a5db | 2006-08-29 18:12:40 -0400 | [diff] [blame] | 492 | unsigned int pci_mhz; |
| 493 | unsigned int f_low, f_high; |
| 494 | int adjust; |
Jeff Garzik | 85cd725 | 2006-08-31 00:03:49 -0400 | [diff] [blame] | 495 | |
Jeff Garzik | 669a5db | 2006-08-29 18:12:40 -0400 | [diff] [blame] | 496 | pci_read_config_dword(dev, PCI_CLASS_REVISION, &class_rev); |
| 497 | class_rev &= 0xFF; |
Jeff Garzik | 85cd725 | 2006-08-31 00:03:49 -0400 | [diff] [blame] | 498 | |
Jeff Garzik | 669a5db | 2006-08-29 18:12:40 -0400 | [diff] [blame] | 499 | switch(dev->device) { |
| 500 | case PCI_DEVICE_ID_TTI_HPT366: |
| 501 | if (class_rev < 6) |
| 502 | return -ENODEV; |
| 503 | break; |
| 504 | case PCI_DEVICE_ID_TTI_HPT372: |
| 505 | /* 372N if rev >= 1*/ |
| 506 | if (class_rev == 0) |
| 507 | return -ENODEV; |
| 508 | break; |
| 509 | case PCI_DEVICE_ID_TTI_HPT302: |
| 510 | if (class_rev < 2) |
| 511 | return -ENODEV; |
| 512 | break; |
| 513 | case PCI_DEVICE_ID_TTI_HPT372N: |
| 514 | break; |
| 515 | default: |
| 516 | printk(KERN_ERR "pata_hpt3x2n: PCI table is bogus please report (%d).\n", dev->device); |
| 517 | return -ENODEV; |
| 518 | } |
| 519 | |
| 520 | /* Ok so this is a chip we support */ |
| 521 | |
| 522 | pci_write_config_byte(dev, PCI_CACHE_LINE_SIZE, (L1_CACHE_BYTES / 4)); |
| 523 | pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0x78); |
| 524 | pci_write_config_byte(dev, PCI_MIN_GNT, 0x08); |
| 525 | pci_write_config_byte(dev, PCI_MAX_LAT, 0x08); |
| 526 | |
| 527 | pci_read_config_byte(dev, 0x5A, &irqmask); |
| 528 | irqmask &= ~0x10; |
| 529 | pci_write_config_byte(dev, 0x5a, irqmask); |
| 530 | |
| 531 | /* Tune the PLL. HPT recommend using 75 for SATA, 66 for UDMA133 or |
| 532 | 50 for UDMA100. Right now we always use 66 */ |
Jeff Garzik | 85cd725 | 2006-08-31 00:03:49 -0400 | [diff] [blame] | 533 | |
Jeff Garzik | 669a5db | 2006-08-29 18:12:40 -0400 | [diff] [blame] | 534 | pci_mhz = hpt3x2n_pci_clock(dev); |
Jeff Garzik | 85cd725 | 2006-08-31 00:03:49 -0400 | [diff] [blame] | 535 | |
Jeff Garzik | 669a5db | 2006-08-29 18:12:40 -0400 | [diff] [blame] | 536 | f_low = (pci_mhz * 48) / 66; /* PCI Mhz for 66Mhz DPLL */ |
| 537 | f_high = f_low + 2; /* Tolerance */ |
Jeff Garzik | 85cd725 | 2006-08-31 00:03:49 -0400 | [diff] [blame] | 538 | |
Jeff Garzik | 669a5db | 2006-08-29 18:12:40 -0400 | [diff] [blame] | 539 | pci_write_config_dword(dev, 0x5C, (f_high << 16) | f_low | 0x100); |
| 540 | /* PLL clock */ |
| 541 | pci_write_config_byte(dev, 0x5B, 0x21); |
Jeff Garzik | 85cd725 | 2006-08-31 00:03:49 -0400 | [diff] [blame] | 542 | |
Jeff Garzik | 669a5db | 2006-08-29 18:12:40 -0400 | [diff] [blame] | 543 | /* Unlike the 37x we don't try jiggling the frequency */ |
| 544 | for(adjust = 0; adjust < 8; adjust++) { |
| 545 | if (hpt3xn_calibrate_dpll(dev)) |
| 546 | break; |
| 547 | pci_write_config_dword(dev, 0x5C, (f_high << 16) | f_low); |
| 548 | } |
| 549 | if (adjust == 8) |
| 550 | printk(KERN_WARNING "hpt3xn: DPLL did not stabilize.\n"); |
| 551 | |
| 552 | /* Set our private data up. We only need a few flags so we use |
| 553 | it directly */ |
| 554 | port->private_data = NULL; |
| 555 | if (pci_mhz > 60) |
| 556 | port->private_data = (void *)PCI66; |
Jeff Garzik | 85cd725 | 2006-08-31 00:03:49 -0400 | [diff] [blame] | 557 | |
Jeff Garzik | 669a5db | 2006-08-29 18:12:40 -0400 | [diff] [blame] | 558 | /* Now kick off ATA set up */ |
| 559 | port_info[0] = port_info[1] = port; |
| 560 | return ata_pci_init_one(dev, port_info, 2); |
| 561 | } |
| 562 | |
Jeff Garzik | 2d2744f | 2006-09-28 20:21:59 -0400 | [diff] [blame] | 563 | static const struct pci_device_id hpt3x2n[] = { |
| 564 | { PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT366), }, |
| 565 | { PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT372), }, |
| 566 | { PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT302), }, |
| 567 | { PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT372N), }, |
| 568 | |
| 569 | { }, |
Jeff Garzik | 669a5db | 2006-08-29 18:12:40 -0400 | [diff] [blame] | 570 | }; |
| 571 | |
| 572 | static struct pci_driver hpt3x2n_pci_driver = { |
Jeff Garzik | 2d2744f | 2006-09-28 20:21:59 -0400 | [diff] [blame] | 573 | .name = DRV_NAME, |
Jeff Garzik | 669a5db | 2006-08-29 18:12:40 -0400 | [diff] [blame] | 574 | .id_table = hpt3x2n, |
| 575 | .probe = hpt3x2n_init_one, |
| 576 | .remove = ata_pci_remove_one |
| 577 | }; |
| 578 | |
| 579 | static int __init hpt3x2n_init(void) |
| 580 | { |
| 581 | return pci_register_driver(&hpt3x2n_pci_driver); |
| 582 | } |
| 583 | |
Jeff Garzik | 669a5db | 2006-08-29 18:12:40 -0400 | [diff] [blame] | 584 | static void __exit hpt3x2n_exit(void) |
| 585 | { |
| 586 | pci_unregister_driver(&hpt3x2n_pci_driver); |
| 587 | } |
| 588 | |
Jeff Garzik | 669a5db | 2006-08-29 18:12:40 -0400 | [diff] [blame] | 589 | MODULE_AUTHOR("Alan Cox"); |
| 590 | MODULE_DESCRIPTION("low-level driver for the Highpoint HPT3x2n/30x"); |
| 591 | MODULE_LICENSE("GPL"); |
| 592 | MODULE_DEVICE_TABLE(pci, hpt3x2n); |
| 593 | MODULE_VERSION(DRV_VERSION); |
| 594 | |
| 595 | module_init(hpt3x2n_init); |
| 596 | module_exit(hpt3x2n_exit); |