blob: e4e651cca3e448185cefb4a9474f9cf7baad12f0 [file] [log] [blame]
Linus Torvalds1da177e2005-04-16 15:20:36 -07001/*
2 * Core definitions and data structures shareable across OS platforms.
3 *
4 * Copyright (c) 1994-2001 Justin T. Gibbs.
5 * Copyright (c) 2000-2001 Adaptec Inc.
6 * All rights reserved.
7 *
8 * Redistribution and use in source and binary forms, with or without
9 * modification, are permitted provided that the following conditions
10 * are met:
11 * 1. Redistributions of source code must retain the above copyright
12 * notice, this list of conditions, and the following disclaimer,
13 * without modification.
14 * 2. Redistributions in binary form must reproduce at minimum a disclaimer
15 * substantially similar to the "NO WARRANTY" disclaimer below
16 * ("Disclaimer") and any redistribution must be conditioned upon
17 * including a substantially similar Disclaimer requirement for further
18 * binary redistribution.
19 * 3. Neither the names of the above-listed copyright holders nor the names
20 * of any contributors may be used to endorse or promote products derived
21 * from this software without specific prior written permission.
22 *
23 * Alternatively, this software may be distributed under the terms of the
24 * GNU General Public License ("GPL") version 2 as published by the Free
25 * Software Foundation.
26 *
27 * NO WARRANTY
28 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
29 * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
30 * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR
31 * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
32 * HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
33 * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
34 * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
35 * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
36 * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING
37 * IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
38 * POSSIBILITY OF SUCH DAMAGES.
39 *
James Bottomley79778a22005-08-04 17:33:22 -050040 * $Id: //depot/aic7xxx/aic7xxx/aic7xxx.h#85 $
Linus Torvalds1da177e2005-04-16 15:20:36 -070041 *
42 * $FreeBSD$
43 */
44
45#ifndef _AIC7XXX_H_
46#define _AIC7XXX_H_
47
48/* Register Definitions */
49#include "aic7xxx_reg.h"
50
51/************************* Forward Declarations *******************************/
52struct ahc_platform_data;
53struct scb_platform_data;
54struct seeprom_descriptor;
55
56/****************************** Useful Macros *********************************/
Linus Torvalds1da177e2005-04-16 15:20:36 -070057#ifndef TRUE
58#define TRUE 1
59#endif
60#ifndef FALSE
61#define FALSE 0
62#endif
63
Linus Torvalds1da177e2005-04-16 15:20:36 -070064#define ALL_CHANNELS '\0'
65#define ALL_TARGETS_MASK 0xFFFF
66#define INITIATOR_WILDCARD (~0)
67
68#define SCSIID_TARGET(ahc, scsiid) \
69 (((scsiid) & ((((ahc)->features & AHC_TWIN) != 0) ? TWIN_TID : TID)) \
70 >> TID_SHIFT)
71#define SCSIID_OUR_ID(scsiid) \
72 ((scsiid) & OID)
73#define SCSIID_CHANNEL(ahc, scsiid) \
74 ((((ahc)->features & AHC_TWIN) != 0) \
75 ? ((((scsiid) & TWIN_CHNLB) != 0) ? 'B' : 'A') \
76 : 'A')
77#define SCB_IS_SCSIBUS_B(ahc, scb) \
78 (SCSIID_CHANNEL(ahc, (scb)->hscb->scsiid) == 'B')
79#define SCB_GET_OUR_ID(scb) \
80 SCSIID_OUR_ID((scb)->hscb->scsiid)
81#define SCB_GET_TARGET(ahc, scb) \
82 SCSIID_TARGET((ahc), (scb)->hscb->scsiid)
83#define SCB_GET_CHANNEL(ahc, scb) \
84 SCSIID_CHANNEL(ahc, (scb)->hscb->scsiid)
85#define SCB_GET_LUN(scb) \
86 ((scb)->hscb->lun & LID)
87#define SCB_GET_TARGET_OFFSET(ahc, scb) \
88 (SCB_GET_TARGET(ahc, scb) + (SCB_IS_SCSIBUS_B(ahc, scb) ? 8 : 0))
89#define SCB_GET_TARGET_MASK(ahc, scb) \
90 (0x01 << (SCB_GET_TARGET_OFFSET(ahc, scb)))
91#ifdef AHC_DEBUG
92#define SCB_IS_SILENT(scb) \
93 ((ahc_debug & AHC_SHOW_MASKED_ERRORS) == 0 \
94 && (((scb)->flags & SCB_SILENT) != 0))
95#else
96#define SCB_IS_SILENT(scb) \
97 (((scb)->flags & SCB_SILENT) != 0)
98#endif
99#define TCL_TARGET_OFFSET(tcl) \
100 ((((tcl) >> 4) & TID) >> 4)
101#define TCL_LUN(tcl) \
102 (tcl & (AHC_NUM_LUNS - 1))
103#define BUILD_TCL(scsiid, lun) \
104 ((lun) | (((scsiid) & TID) << 4))
105
106#ifndef AHC_TARGET_MODE
107#undef AHC_TMODE_ENABLE
108#define AHC_TMODE_ENABLE 0
109#endif
110
111/**************************** Driver Constants ********************************/
112/*
113 * The maximum number of supported targets.
114 */
115#define AHC_NUM_TARGETS 16
116
117/*
118 * The maximum number of supported luns.
119 * The identify message only supports 64 luns in SPI3.
120 * You can have 2^64 luns when information unit transfers are enabled,
121 * but it is doubtful this driver will ever support IUTs.
122 */
123#define AHC_NUM_LUNS 64
124
125/*
126 * The maximum transfer per S/G segment.
127 */
128#define AHC_MAXTRANSFER_SIZE 0x00ffffff /* limited by 24bit counter */
129
130/*
131 * The maximum amount of SCB storage in hardware on a controller.
132 * This value represents an upper bound. Controllers vary in the number
133 * they actually support.
134 */
135#define AHC_SCB_MAX 255
136
137/*
138 * The maximum number of concurrent transactions supported per driver instance.
139 * Sequencer Control Blocks (SCBs) store per-transaction information. Although
140 * the space for SCBs on the host adapter varies by model, the driver will
141 * page the SCBs between host and controller memory as needed. We are limited
142 * to 253 because:
143 * 1) The 8bit nature of the RISC engine holds us to an 8bit value.
144 * 2) We reserve one value, 255, to represent the invalid element.
145 * 3) Our input queue scheme requires one SCB to always be reserved
146 * in advance of queuing any SCBs. This takes us down to 254.
147 * 4) To handle our output queue correctly on machines that only
148 * support 32bit stores, we must clear the array 4 bytes at a
149 * time. To avoid colliding with a DMA write from the sequencer,
150 * we must be sure that 4 slots are empty when we write to clear
151 * the queue. This reduces us to 253 SCBs: 1 that just completed
152 * and the known three additional empty slots in the queue that
153 * precede it.
154 */
155#define AHC_MAX_QUEUE 253
156
157/*
158 * The maximum amount of SCB storage we allocate in host memory. This
159 * number should reflect the 1 additional SCB we require to handle our
160 * qinfifo mechanism.
161 */
162#define AHC_SCB_MAX_ALLOC (AHC_MAX_QUEUE+1)
163
164/*
165 * Ring Buffer of incoming target commands.
166 * We allocate 256 to simplify the logic in the sequencer
167 * by using the natural wrap point of an 8bit counter.
168 */
169#define AHC_TMODE_CMDS 256
170
171/* Reset line assertion time in us */
172#define AHC_BUSRESET_DELAY 25
173
174/******************* Chip Characteristics/Operating Settings *****************/
175/*
176 * Chip Type
177 * The chip order is from least sophisticated to most sophisticated.
178 */
179typedef enum {
180 AHC_NONE = 0x0000,
181 AHC_CHIPID_MASK = 0x00FF,
182 AHC_AIC7770 = 0x0001,
183 AHC_AIC7850 = 0x0002,
184 AHC_AIC7855 = 0x0003,
185 AHC_AIC7859 = 0x0004,
186 AHC_AIC7860 = 0x0005,
187 AHC_AIC7870 = 0x0006,
188 AHC_AIC7880 = 0x0007,
189 AHC_AIC7895 = 0x0008,
190 AHC_AIC7895C = 0x0009,
191 AHC_AIC7890 = 0x000a,
192 AHC_AIC7896 = 0x000b,
193 AHC_AIC7892 = 0x000c,
194 AHC_AIC7899 = 0x000d,
195 AHC_VL = 0x0100, /* Bus type VL */
196 AHC_EISA = 0x0200, /* Bus type EISA */
197 AHC_PCI = 0x0400, /* Bus type PCI */
198 AHC_BUS_MASK = 0x0F00
199} ahc_chip;
200
201/*
202 * Features available in each chip type.
203 */
204typedef enum {
205 AHC_FENONE = 0x00000,
206 AHC_ULTRA = 0x00001, /* Supports 20MHz Transfers */
207 AHC_ULTRA2 = 0x00002, /* Supports 40MHz Transfers */
208 AHC_WIDE = 0x00004, /* Wide Channel */
209 AHC_TWIN = 0x00008, /* Twin Channel */
210 AHC_MORE_SRAM = 0x00010, /* 80 bytes instead of 64 */
211 AHC_CMD_CHAN = 0x00020, /* Has a Command DMA Channel */
212 AHC_QUEUE_REGS = 0x00040, /* Has Queue management registers */
213 AHC_SG_PRELOAD = 0x00080, /* Can perform auto-SG preload */
214 AHC_SPIOCAP = 0x00100, /* Has a Serial Port I/O Cap Register */
215 AHC_MULTI_TID = 0x00200, /* Has bitmask of TIDs for select-in */
216 AHC_HS_MAILBOX = 0x00400, /* Has HS_MAILBOX register */
217 AHC_DT = 0x00800, /* Double Transition transfers */
218 AHC_NEW_TERMCTL = 0x01000, /* Newer termination scheme */
219 AHC_MULTI_FUNC = 0x02000, /* Multi-Function Twin Channel Device */
220 AHC_LARGE_SCBS = 0x04000, /* 64byte SCBs */
221 AHC_AUTORATE = 0x08000, /* Automatic update of SCSIRATE/OFFSET*/
222 AHC_AUTOPAUSE = 0x10000, /* Automatic pause on register access */
223 AHC_TARGETMODE = 0x20000, /* Has tested target mode support */
224 AHC_MULTIROLE = 0x40000, /* Space for two roles at a time */
225 AHC_REMOVABLE = 0x80000, /* Hot-Swap supported */
James Bottomleyb2d8bfe2006-06-10 10:49:07 -0500226 AHC_HVD = 0x100000, /* HVD rather than SE */
Linus Torvalds1da177e2005-04-16 15:20:36 -0700227 AHC_AIC7770_FE = AHC_FENONE,
228 /*
229 * The real 7850 does not support Ultra modes, but there are
230 * several cards that use the generic 7850 PCI ID even though
231 * they are using an Ultra capable chip (7859/7860). We start
232 * out with the AHC_ULTRA feature set and then check the DEVSTATUS
233 * register to determine if the capability is really present.
234 */
235 AHC_AIC7850_FE = AHC_SPIOCAP|AHC_AUTOPAUSE|AHC_TARGETMODE|AHC_ULTRA,
236 AHC_AIC7860_FE = AHC_AIC7850_FE,
James Bottomley79778a22005-08-04 17:33:22 -0500237 AHC_AIC7870_FE = AHC_TARGETMODE|AHC_AUTOPAUSE,
Linus Torvalds1da177e2005-04-16 15:20:36 -0700238 AHC_AIC7880_FE = AHC_AIC7870_FE|AHC_ULTRA,
239 /*
240 * Although we have space for both the initiator and
241 * target roles on ULTRA2 chips, we currently disable
242 * the initiator role to allow multi-scsi-id target mode
243 * configurations. We can only respond on the same SCSI
244 * ID as our initiator role if we allow initiator operation.
245 * At some point, we should add a configuration knob to
246 * allow both roles to be loaded.
247 */
248 AHC_AIC7890_FE = AHC_MORE_SRAM|AHC_CMD_CHAN|AHC_ULTRA2
249 |AHC_QUEUE_REGS|AHC_SG_PRELOAD|AHC_MULTI_TID
250 |AHC_HS_MAILBOX|AHC_NEW_TERMCTL|AHC_LARGE_SCBS
251 |AHC_TARGETMODE,
252 AHC_AIC7892_FE = AHC_AIC7890_FE|AHC_DT|AHC_AUTORATE|AHC_AUTOPAUSE,
253 AHC_AIC7895_FE = AHC_AIC7880_FE|AHC_MORE_SRAM|AHC_AUTOPAUSE
254 |AHC_CMD_CHAN|AHC_MULTI_FUNC|AHC_LARGE_SCBS,
255 AHC_AIC7895C_FE = AHC_AIC7895_FE|AHC_MULTI_TID,
256 AHC_AIC7896_FE = AHC_AIC7890_FE|AHC_MULTI_FUNC,
257 AHC_AIC7899_FE = AHC_AIC7892_FE|AHC_MULTI_FUNC
258} ahc_feature;
259
260/*
261 * Bugs in the silicon that we work around in software.
262 */
263typedef enum {
264 AHC_BUGNONE = 0x00,
265 /*
266 * On all chips prior to the U2 product line,
267 * the WIDEODD S/G segment feature does not
268 * work during scsi->HostBus transfers.
269 */
270 AHC_TMODE_WIDEODD_BUG = 0x01,
271 /*
272 * On the aic7890/91 Rev 0 chips, the autoflush
273 * feature does not work. A manual flush of
274 * the DMA FIFO is required.
275 */
276 AHC_AUTOFLUSH_BUG = 0x02,
277 /*
278 * On many chips, cacheline streaming does not work.
279 */
280 AHC_CACHETHEN_BUG = 0x04,
281 /*
282 * On the aic7896/97 chips, cacheline
283 * streaming must be enabled.
284 */
285 AHC_CACHETHEN_DIS_BUG = 0x08,
286 /*
287 * PCI 2.1 Retry failure on non-empty data fifo.
288 */
289 AHC_PCI_2_1_RETRY_BUG = 0x10,
290 /*
291 * Controller does not handle cacheline residuals
292 * properly on S/G segments if PCI MWI instructions
293 * are allowed.
294 */
295 AHC_PCI_MWI_BUG = 0x20,
296 /*
297 * An SCB upload using the SCB channel's
298 * auto array entry copy feature may
299 * corrupt data. This appears to only
300 * occur on 66MHz systems.
301 */
302 AHC_SCBCHAN_UPLOAD_BUG = 0x40
303} ahc_bug;
304
305/*
306 * Configuration specific settings.
307 * The driver determines these settings by probing the
308 * chip/controller's configuration.
309 */
310typedef enum {
311 AHC_FNONE = 0x000,
312 AHC_PRIMARY_CHANNEL = 0x003, /*
313 * The channel that should
314 * be probed first.
315 */
316 AHC_USEDEFAULTS = 0x004, /*
317 * For cards without an seeprom
318 * or a BIOS to initialize the chip's
319 * SRAM, we use the default target
320 * settings.
321 */
322 AHC_SEQUENCER_DEBUG = 0x008,
323 AHC_SHARED_SRAM = 0x010,
324 AHC_LARGE_SEEPROM = 0x020, /* Uses C56_66 not C46 */
325 AHC_RESET_BUS_A = 0x040,
326 AHC_RESET_BUS_B = 0x080,
327 AHC_EXTENDED_TRANS_A = 0x100,
328 AHC_EXTENDED_TRANS_B = 0x200,
329 AHC_TERM_ENB_A = 0x400,
330 AHC_TERM_ENB_B = 0x800,
331 AHC_INITIATORROLE = 0x1000, /*
332 * Allow initiator operations on
333 * this controller.
334 */
335 AHC_TARGETROLE = 0x2000, /*
336 * Allow target operations on this
337 * controller.
338 */
339 AHC_NEWEEPROM_FMT = 0x4000,
Linus Torvalds1da177e2005-04-16 15:20:36 -0700340 AHC_TQINFIFO_BLOCKED = 0x10000, /* Blocked waiting for ATIOs */
341 AHC_INT50_SPEEDFLEX = 0x20000, /*
342 * Internal 50pin connector
343 * sits behind an aic3860
344 */
345 AHC_SCB_BTT = 0x40000, /*
346 * The busy targets table is
347 * stored in SCB space rather
348 * than SRAM.
349 */
350 AHC_BIOS_ENABLED = 0x80000,
351 AHC_ALL_INTERRUPTS = 0x100000,
352 AHC_PAGESCBS = 0x400000, /* Enable SCB paging */
353 AHC_EDGE_INTERRUPT = 0x800000, /* Device uses edge triggered ints */
354 AHC_39BIT_ADDRESSING = 0x1000000, /* Use 39 bit addressing scheme. */
355 AHC_LSCBS_ENABLED = 0x2000000, /* 64Byte SCBs enabled */
356 AHC_SCB_CONFIG_USED = 0x4000000, /* No SEEPROM but SCB2 had info. */
357 AHC_NO_BIOS_INIT = 0x8000000, /* No BIOS left over settings. */
358 AHC_DISABLE_PCI_PERR = 0x10000000,
359 AHC_HAS_TERM_LOGIC = 0x20000000
360} ahc_flag;
361
362/************************* Hardware SCB Definition ***************************/
363
364/*
365 * The driver keeps up to MAX_SCB scb structures per card in memory. The SCB
366 * consists of a "hardware SCB" mirroring the fields available on the card
367 * and additional information the kernel stores for each transaction.
368 *
369 * To minimize space utilization, a portion of the hardware scb stores
370 * different data during different portions of a SCSI transaction.
371 * As initialized by the host driver for the initiator role, this area
372 * contains the SCSI cdb (or a pointer to the cdb) to be executed. After
373 * the cdb has been presented to the target, this area serves to store
374 * residual transfer information and the SCSI status byte.
375 * For the target role, the contents of this area do not change, but
376 * still serve a different purpose than for the initiator role. See
377 * struct target_data for details.
378 */
379
380/*
381 * Status information embedded in the shared poriton of
382 * an SCB after passing the cdb to the target. The kernel
383 * driver will only read this data for transactions that
384 * complete abnormally (non-zero status byte).
385 */
386struct status_pkt {
387 uint32_t residual_datacnt; /* Residual in the current S/G seg */
388 uint32_t residual_sg_ptr; /* The next S/G for this transfer */
389 uint8_t scsi_status; /* Standard SCSI status byte */
390};
391
392/*
393 * Target mode version of the shared data SCB segment.
394 */
395struct target_data {
396 uint32_t residual_datacnt; /* Residual in the current S/G seg */
397 uint32_t residual_sg_ptr; /* The next S/G for this transfer */
398 uint8_t scsi_status; /* SCSI status to give to initiator */
399 uint8_t target_phases; /* Bitmap of phases to execute */
400 uint8_t data_phase; /* Data-In or Data-Out */
401 uint8_t initiator_tag; /* Initiator's transaction tag */
402};
403
404struct hardware_scb {
405/*0*/ union {
406 /*
407 * If the cdb is 12 bytes or less, we embed it directly
408 * in the SCB. For longer cdbs, we embed the address
409 * of the cdb payload as seen by the chip and a DMA
410 * is used to pull it in.
411 */
412 uint8_t cdb[12];
413 uint32_t cdb_ptr;
414 struct status_pkt status;
415 struct target_data tdata;
416 } shared_data;
417/*
418 * A word about residuals.
419 * The scb is presented to the sequencer with the dataptr and datacnt
420 * fields initialized to the contents of the first S/G element to
421 * transfer. The sgptr field is initialized to the bus address for
422 * the S/G element that follows the first in the in core S/G array
423 * or'ed with the SG_FULL_RESID flag. Sgptr may point to an invalid
424 * S/G entry for this transfer (single S/G element transfer with the
425 * first elements address and length preloaded in the dataptr/datacnt
426 * fields). If no transfer is to occur, sgptr is set to SG_LIST_NULL.
427 * The SG_FULL_RESID flag ensures that the residual will be correctly
428 * noted even if no data transfers occur. Once the data phase is entered,
429 * the residual sgptr and datacnt are loaded from the sgptr and the
430 * datacnt fields. After each S/G element's dataptr and length are
431 * loaded into the hardware, the residual sgptr is advanced. After
432 * each S/G element is expired, its datacnt field is checked to see
433 * if the LAST_SEG flag is set. If so, SG_LIST_NULL is set in the
434 * residual sg ptr and the transfer is considered complete. If the
435 * sequencer determines that there is a residual in the tranfer, it
436 * will set the SG_RESID_VALID flag in sgptr and dma the scb back into
437 * host memory. To sumarize:
438 *
439 * Sequencer:
440 * o A residual has occurred if SG_FULL_RESID is set in sgptr,
441 * or residual_sgptr does not have SG_LIST_NULL set.
442 *
443 * o We are transfering the last segment if residual_datacnt has
444 * the SG_LAST_SEG flag set.
445 *
446 * Host:
447 * o A residual has occurred if a completed scb has the
448 * SG_RESID_VALID flag set.
449 *
450 * o residual_sgptr and sgptr refer to the "next" sg entry
451 * and so may point beyond the last valid sg entry for the
452 * transfer.
453 */
454/*12*/ uint32_t dataptr;
455/*16*/ uint32_t datacnt; /*
456 * Byte 3 (numbered from 0) of
457 * the datacnt is really the
458 * 4th byte in that data address.
459 */
460/*20*/ uint32_t sgptr;
461#define SG_PTR_MASK 0xFFFFFFF8
462/*24*/ uint8_t control; /* See SCB_CONTROL in aic7xxx.reg for details */
463/*25*/ uint8_t scsiid; /* what to load in the SCSIID register */
464/*26*/ uint8_t lun;
465/*27*/ uint8_t tag; /*
466 * Index into our kernel SCB array.
467 * Also used as the tag for tagged I/O
468 */
469/*28*/ uint8_t cdb_len;
470/*29*/ uint8_t scsirate; /* Value for SCSIRATE register */
471/*30*/ uint8_t scsioffset; /* Value for SCSIOFFSET register */
472/*31*/ uint8_t next; /*
473 * Used for threading SCBs in the
474 * "Waiting for Selection" and
475 * "Disconnected SCB" lists down
476 * in the sequencer.
477 */
478/*32*/ uint8_t cdb32[32]; /*
479 * CDB storage for cdbs of size
480 * 13->32. We store them here
481 * because hardware scbs are
482 * allocated from DMA safe
483 * memory so we are guaranteed
484 * the controller can access
485 * this data.
486 */
487};
488
489/************************ Kernel SCB Definitions ******************************/
490/*
491 * Some fields of the SCB are OS dependent. Here we collect the
492 * definitions for elements that all OS platforms need to include
493 * in there SCB definition.
494 */
495
496/*
497 * Definition of a scatter/gather element as transfered to the controller.
498 * The aic7xxx chips only support a 24bit length. We use the top byte of
499 * the length to store additional address bits and a flag to indicate
500 * that a given segment terminates the transfer. This gives us an
501 * addressable range of 512GB on machines with 64bit PCI or with chips
502 * that can support dual address cycles on 32bit PCI busses.
503 */
504struct ahc_dma_seg {
505 uint32_t addr;
506 uint32_t len;
507#define AHC_DMA_LAST_SEG 0x80000000
508#define AHC_SG_HIGH_ADDR_MASK 0x7F000000
509#define AHC_SG_LEN_MASK 0x00FFFFFF
510};
511
512struct sg_map_node {
513 bus_dmamap_t sg_dmamap;
514 dma_addr_t sg_physaddr;
515 struct ahc_dma_seg* sg_vaddr;
516 SLIST_ENTRY(sg_map_node) links;
517};
518
519/*
520 * The current state of this SCB.
521 */
522typedef enum {
523 SCB_FREE = 0x0000,
524 SCB_OTHERTCL_TIMEOUT = 0x0002,/*
525 * Another device was active
526 * during the first timeout for
527 * this SCB so we gave ourselves
528 * an additional timeout period
529 * in case it was hogging the
530 * bus.
531 */
532 SCB_DEVICE_RESET = 0x0004,
533 SCB_SENSE = 0x0008,
534 SCB_CDB32_PTR = 0x0010,
535 SCB_RECOVERY_SCB = 0x0020,
536 SCB_AUTO_NEGOTIATE = 0x0040,/* Negotiate to achieve goal. */
537 SCB_NEGOTIATE = 0x0080,/* Negotiation forced for command. */
538 SCB_ABORT = 0x0100,
539 SCB_UNTAGGEDQ = 0x0200,
540 SCB_ACTIVE = 0x0400,
541 SCB_TARGET_IMMEDIATE = 0x0800,
542 SCB_TRANSMISSION_ERROR = 0x1000,/*
543 * We detected a parity or CRC
544 * error that has effected the
545 * payload of the command. This
546 * flag is checked when normal
547 * status is returned to catch
548 * the case of a target not
549 * responding to our attempt
550 * to report the error.
551 */
552 SCB_TARGET_SCB = 0x2000,
553 SCB_SILENT = 0x4000 /*
554 * Be quiet about transmission type
555 * errors. They are expected and we
556 * don't want to upset the user. This
557 * flag is typically used during DV.
558 */
559} scb_flag;
560
561struct scb {
562 struct hardware_scb *hscb;
563 union {
564 SLIST_ENTRY(scb) sle;
565 TAILQ_ENTRY(scb) tqe;
566 } links;
567 LIST_ENTRY(scb) pending_links;
568 ahc_io_ctx_t io_ctx;
569 struct ahc_softc *ahc_softc;
570 scb_flag flags;
571#ifndef __linux__
572 bus_dmamap_t dmamap;
573#endif
574 struct scb_platform_data *platform_data;
575 struct sg_map_node *sg_map;
576 struct ahc_dma_seg *sg_list;
577 dma_addr_t sg_list_phys;
578 u_int sg_count;/* How full ahc_dma_seg is */
579};
580
581struct scb_data {
582 SLIST_HEAD(, scb) free_scbs; /*
583 * Pool of SCBs ready to be assigned
584 * commands to execute.
585 */
586 struct scb *scbindex[256]; /*
587 * Mapping from tag to SCB.
588 * As tag identifiers are an
589 * 8bit value, we provide space
590 * for all possible tag values.
591 * Any lookups to entries at or
592 * above AHC_SCB_MAX_ALLOC will
593 * always fail.
594 */
595 struct hardware_scb *hscbs; /* Array of hardware SCBs */
596 struct scb *scbarray; /* Array of kernel SCBs */
597 struct scsi_sense_data *sense; /* Per SCB sense data */
598
599 /*
600 * "Bus" addresses of our data structures.
601 */
602 bus_dma_tag_t hscb_dmat; /* dmat for our hardware SCB array */
603 bus_dmamap_t hscb_dmamap;
604 dma_addr_t hscb_busaddr;
605 bus_dma_tag_t sense_dmat;
606 bus_dmamap_t sense_dmamap;
607 dma_addr_t sense_busaddr;
608 bus_dma_tag_t sg_dmat; /* dmat for our sg segments */
609 SLIST_HEAD(, sg_map_node) sg_maps;
610 uint8_t numscbs;
611 uint8_t maxhscbs; /* Number of SCBs on the card */
612 uint8_t init_level; /*
613 * How far we've initialized
614 * this structure.
615 */
616};
617
618/************************ Target Mode Definitions *****************************/
619
620/*
621 * Connection desciptor for select-in requests in target mode.
622 */
623struct target_cmd {
624 uint8_t scsiid; /* Our ID and the initiator's ID */
625 uint8_t identify; /* Identify message */
626 uint8_t bytes[22]; /*
627 * Bytes contains any additional message
628 * bytes terminated by 0xFF. The remainder
629 * is the cdb to execute.
630 */
631 uint8_t cmd_valid; /*
632 * When a command is complete, the firmware
633 * will set cmd_valid to all bits set.
634 * After the host has seen the command,
635 * the bits are cleared. This allows us
636 * to just peek at host memory to determine
637 * if more work is complete. cmd_valid is on
638 * an 8 byte boundary to simplify setting
639 * it on aic7880 hardware which only has
640 * limited direct access to the DMA FIFO.
641 */
642 uint8_t pad[7];
643};
644
645/*
646 * Number of events we can buffer up if we run out
647 * of immediate notify ccbs.
648 */
649#define AHC_TMODE_EVENT_BUFFER_SIZE 8
650struct ahc_tmode_event {
651 uint8_t initiator_id;
652 uint8_t event_type; /* MSG type or EVENT_TYPE_BUS_RESET */
653#define EVENT_TYPE_BUS_RESET 0xFF
654 uint8_t event_arg;
655};
656
657/*
658 * Per enabled lun target mode state.
659 * As this state is directly influenced by the host OS'es target mode
660 * environment, we let the OS module define it. Forward declare the
661 * structure here so we can store arrays of them, etc. in OS neutral
662 * data structures.
663 */
664#ifdef AHC_TARGET_MODE
665struct ahc_tmode_lstate {
666 struct cam_path *path;
667 struct ccb_hdr_slist accept_tios;
668 struct ccb_hdr_slist immed_notifies;
669 struct ahc_tmode_event event_buffer[AHC_TMODE_EVENT_BUFFER_SIZE];
670 uint8_t event_r_idx;
671 uint8_t event_w_idx;
672};
673#else
674struct ahc_tmode_lstate;
675#endif
676
677/******************** Transfer Negotiation Datastructures *********************/
678#define AHC_TRANS_CUR 0x01 /* Modify current neogtiation status */
679#define AHC_TRANS_ACTIVE 0x03 /* Assume this target is on the bus */
680#define AHC_TRANS_GOAL 0x04 /* Modify negotiation goal */
681#define AHC_TRANS_USER 0x08 /* Modify user negotiation settings */
682
683#define AHC_WIDTH_UNKNOWN 0xFF
684#define AHC_PERIOD_UNKNOWN 0xFF
685#define AHC_OFFSET_UNKNOWN 0xFF
686#define AHC_PPR_OPTS_UNKNOWN 0xFF
687
688/*
689 * Transfer Negotiation Information.
690 */
691struct ahc_transinfo {
692 uint8_t protocol_version; /* SCSI Revision level */
693 uint8_t transport_version; /* SPI Revision level */
694 uint8_t width; /* Bus width */
695 uint8_t period; /* Sync rate factor */
696 uint8_t offset; /* Sync offset */
697 uint8_t ppr_options; /* Parallel Protocol Request options */
698};
699
700/*
701 * Per-initiator current, goal and user transfer negotiation information. */
702struct ahc_initiator_tinfo {
703 uint8_t scsirate; /* Computed value for SCSIRATE reg */
704 struct ahc_transinfo curr;
705 struct ahc_transinfo goal;
706 struct ahc_transinfo user;
707};
708
709/*
710 * Per enabled target ID state.
711 * Pointers to lun target state as well as sync/wide negotiation information
712 * for each initiator<->target mapping. For the initiator role we pretend
713 * that we are the target and the targets are the initiators since the
714 * negotiation is the same regardless of role.
715 */
716struct ahc_tmode_tstate {
717 struct ahc_tmode_lstate* enabled_luns[AHC_NUM_LUNS];
718 struct ahc_initiator_tinfo transinfo[AHC_NUM_TARGETS];
719
720 /*
721 * Per initiator state bitmasks.
722 */
723 uint16_t auto_negotiate;/* Auto Negotiation Required */
724 uint16_t ultraenb; /* Using ultra sync rate */
725 uint16_t discenable; /* Disconnection allowed */
726 uint16_t tagenable; /* Tagged Queuing allowed */
727};
728
729/*
730 * Data structure for our table of allowed synchronous transfer rates.
731 */
732struct ahc_syncrate {
733 u_int sxfr_u2; /* Value of the SXFR parameter for Ultra2+ Chips */
734 u_int sxfr; /* Value of the SXFR parameter for <= Ultra Chips */
735#define ULTRA_SXFR 0x100 /* Rate Requires Ultra Mode set */
736#define ST_SXFR 0x010 /* Rate Single Transition Only */
737#define DT_SXFR 0x040 /* Rate Double Transition Only */
738 uint8_t period; /* Period to send to SCSI target */
Denys Vlasenkod1d7b192008-04-25 04:34:49 +0200739 const char *rate;
Linus Torvalds1da177e2005-04-16 15:20:36 -0700740};
741
742/* Safe and valid period for async negotiations. */
743#define AHC_ASYNC_XFER_PERIOD 0x45
744#define AHC_ULTRA2_XFER_PERIOD 0x0a
745
746/*
747 * Indexes into our table of syncronous transfer rates.
748 */
749#define AHC_SYNCRATE_DT 0
750#define AHC_SYNCRATE_ULTRA2 1
751#define AHC_SYNCRATE_ULTRA 3
752#define AHC_SYNCRATE_FAST 6
753#define AHC_SYNCRATE_MAX AHC_SYNCRATE_DT
754#define AHC_SYNCRATE_MIN 13
755
756/***************************** Lookup Tables **********************************/
757/*
758 * Phase -> name and message out response
759 * to parity errors in each phase table.
760 */
761struct ahc_phase_table_entry {
762 uint8_t phase;
763 uint8_t mesg_out; /* Message response to parity errors */
764 char *phasemsg;
765};
766
767/************************** Serial EEPROM Format ******************************/
768
769struct seeprom_config {
770/*
771 * Per SCSI ID Configuration Flags
772 */
773 uint16_t device_flags[16]; /* words 0-15 */
774#define CFXFER 0x0007 /* synchronous transfer rate */
775#define CFSYNCH 0x0008 /* enable synchronous transfer */
776#define CFDISC 0x0010 /* enable disconnection */
777#define CFWIDEB 0x0020 /* wide bus device */
778#define CFSYNCHISULTRA 0x0040 /* CFSYNCH is an ultra offset (2940AU)*/
779#define CFSYNCSINGLE 0x0080 /* Single-Transition signalling */
780#define CFSTART 0x0100 /* send start unit SCSI command */
781#define CFINCBIOS 0x0200 /* include in BIOS scan */
782#define CFRNFOUND 0x0400 /* report even if not found */
783#define CFMULTILUNDEV 0x0800 /* Probe multiple luns in BIOS scan */
784#define CFWBCACHEENB 0x4000 /* Enable W-Behind Cache on disks */
785#define CFWBCACHENOP 0xc000 /* Don't touch W-Behind Cache */
786
787/*
788 * BIOS Control Bits
789 */
790 uint16_t bios_control; /* word 16 */
791#define CFSUPREM 0x0001 /* support all removeable drives */
792#define CFSUPREMB 0x0002 /* support removeable boot drives */
793#define CFBIOSEN 0x0004 /* BIOS enabled */
794#define CFBIOS_BUSSCAN 0x0008 /* Have the BIOS Scan the Bus */
795#define CFSM2DRV 0x0010 /* support more than two drives */
796#define CFSTPWLEVEL 0x0010 /* Termination level control */
797#define CF284XEXTEND 0x0020 /* extended translation (284x cards) */
798#define CFCTRL_A 0x0020 /* BIOS displays Ctrl-A message */
799#define CFTERM_MENU 0x0040 /* BIOS displays termination menu */
800#define CFEXTEND 0x0080 /* extended translation enabled */
801#define CFSCAMEN 0x0100 /* SCAM enable */
802#define CFMSG_LEVEL 0x0600 /* BIOS Message Level */
803#define CFMSG_VERBOSE 0x0000
804#define CFMSG_SILENT 0x0200
805#define CFMSG_DIAG 0x0400
806#define CFBOOTCD 0x0800 /* Support Bootable CD-ROM */
807/* UNUSED 0xff00 */
808
809/*
810 * Host Adapter Control Bits
811 */
812 uint16_t adapter_control; /* word 17 */
813#define CFAUTOTERM 0x0001 /* Perform Auto termination */
814#define CFULTRAEN 0x0002 /* Ultra SCSI speed enable */
815#define CF284XSELTO 0x0003 /* Selection timeout (284x cards) */
816#define CF284XFIFO 0x000C /* FIFO Threshold (284x cards) */
817#define CFSTERM 0x0004 /* SCSI low byte termination */
818#define CFWSTERM 0x0008 /* SCSI high byte termination */
819#define CFSPARITY 0x0010 /* SCSI parity */
820#define CF284XSTERM 0x0020 /* SCSI low byte term (284x cards) */
821#define CFMULTILUN 0x0020
822#define CFRESETB 0x0040 /* reset SCSI bus at boot */
823#define CFCLUSTERENB 0x0080 /* Cluster Enable */
824#define CFBOOTCHAN 0x0300 /* probe this channel first */
825#define CFBOOTCHANSHIFT 8
826#define CFSEAUTOTERM 0x0400 /* Ultra2 Perform secondary Auto Term*/
827#define CFSELOWTERM 0x0800 /* Ultra2 secondary low term */
828#define CFSEHIGHTERM 0x1000 /* Ultra2 secondary high term */
829#define CFENABLEDV 0x4000 /* Perform Domain Validation*/
830
831/*
832 * Bus Release Time, Host Adapter ID
833 */
834 uint16_t brtime_id; /* word 18 */
835#define CFSCSIID 0x000f /* host adapter SCSI ID */
836/* UNUSED 0x00f0 */
837#define CFBRTIME 0xff00 /* bus release time */
838
839/*
840 * Maximum targets
841 */
842 uint16_t max_targets; /* word 19 */
843#define CFMAXTARG 0x00ff /* maximum targets */
844#define CFBOOTLUN 0x0f00 /* Lun to boot from */
845#define CFBOOTID 0xf000 /* Target to boot from */
846 uint16_t res_1[10]; /* words 20-29 */
847 uint16_t signature; /* Signature == 0x250 */
848#define CFSIGNATURE 0x250
849#define CFSIGNATURE2 0x300
850 uint16_t checksum; /* word 31 */
851};
852
853/**************************** Message Buffer *********************************/
854typedef enum {
855 MSG_TYPE_NONE = 0x00,
856 MSG_TYPE_INITIATOR_MSGOUT = 0x01,
857 MSG_TYPE_INITIATOR_MSGIN = 0x02,
858 MSG_TYPE_TARGET_MSGOUT = 0x03,
859 MSG_TYPE_TARGET_MSGIN = 0x04
860} ahc_msg_type;
861
862typedef enum {
863 MSGLOOP_IN_PROG,
864 MSGLOOP_MSGCOMPLETE,
865 MSGLOOP_TERMINATED
866} msg_loop_stat;
867
868/*********************** Software Configuration Structure *********************/
869TAILQ_HEAD(scb_tailq, scb);
870
871struct ahc_aic7770_softc {
872 /*
873 * Saved register state used for chip_init().
874 */
875 uint8_t busspd;
876 uint8_t bustime;
877};
878
879struct ahc_pci_softc {
880 /*
881 * Saved register state used for chip_init().
882 */
883 uint32_t devconfig;
884 uint16_t targcrccnt;
885 uint8_t command;
886 uint8_t csize_lattime;
887 uint8_t optionmode;
888 uint8_t crccontrol1;
889 uint8_t dscommand0;
890 uint8_t dspcistatus;
891 uint8_t scbbaddr;
892 uint8_t dff_thrsh;
893};
894
895union ahc_bus_softc {
896 struct ahc_aic7770_softc aic7770_softc;
897 struct ahc_pci_softc pci_softc;
898};
899
900typedef void (*ahc_bus_intr_t)(struct ahc_softc *);
901typedef int (*ahc_bus_chip_init_t)(struct ahc_softc *);
902typedef int (*ahc_bus_suspend_t)(struct ahc_softc *);
903typedef int (*ahc_bus_resume_t)(struct ahc_softc *);
904typedef void ahc_callback_t (void *);
905
906struct ahc_softc {
907 bus_space_tag_t tag;
908 bus_space_handle_t bsh;
909#ifndef __linux__
910 bus_dma_tag_t buffer_dmat; /* dmat for buffer I/O */
911#endif
912 struct scb_data *scb_data;
913
914 struct scb *next_queued_scb;
915
916 /*
917 * SCBs that have been sent to the controller
918 */
919 LIST_HEAD(, scb) pending_scbs;
920
921 /*
922 * Counting lock for deferring the release of additional
923 * untagged transactions from the untagged_queues. When
924 * the lock is decremented to 0, all queues in the
925 * untagged_queues array are run.
926 */
927 u_int untagged_queue_lock;
928
929 /*
930 * Per-target queue of untagged-transactions. The
931 * transaction at the head of the queue is the
932 * currently pending untagged transaction for the
933 * target. The driver only allows a single untagged
934 * transaction per target.
935 */
936 struct scb_tailq untagged_queues[AHC_NUM_TARGETS];
937
938 /*
939 * Bus attachment specific data.
940 */
941 union ahc_bus_softc bus_softc;
942
943 /*
944 * Platform specific data.
945 */
946 struct ahc_platform_data *platform_data;
947
948 /*
949 * Platform specific device information.
950 */
951 ahc_dev_softc_t dev_softc;
952
953 /*
954 * Bus specific device information.
955 */
956 ahc_bus_intr_t bus_intr;
957
958 /*
959 * Bus specific initialization required
960 * after a chip reset.
961 */
962 ahc_bus_chip_init_t bus_chip_init;
963
964 /*
Linus Torvalds1da177e2005-04-16 15:20:36 -0700965 * Target mode related state kept on a per enabled lun basis.
966 * Targets that are not enabled will have null entries.
967 * As an initiator, we keep one target entry for our initiator
968 * ID to store our sync/wide transfer settings.
969 */
970 struct ahc_tmode_tstate *enabled_targets[AHC_NUM_TARGETS];
971
972 /*
973 * The black hole device responsible for handling requests for
974 * disabled luns on enabled targets.
975 */
976 struct ahc_tmode_lstate *black_hole;
977
978 /*
979 * Device instance currently on the bus awaiting a continue TIO
980 * for a command that was not given the disconnect priveledge.
981 */
982 struct ahc_tmode_lstate *pending_device;
983
984 /*
985 * Card characteristics
986 */
987 ahc_chip chip;
988 ahc_feature features;
989 ahc_bug bugs;
990 ahc_flag flags;
991 struct seeprom_config *seep_config;
992
993 /* Values to store in the SEQCTL register for pause and unpause */
994 uint8_t unpause;
995 uint8_t pause;
996
997 /* Command Queues */
998 uint8_t qoutfifonext;
999 uint8_t qinfifonext;
1000 uint8_t *qoutfifo;
1001 uint8_t *qinfifo;
1002
1003 /* Critical Section Data */
1004 struct cs *critical_sections;
1005 u_int num_critical_sections;
1006
Linus Torvalds1da177e2005-04-16 15:20:36 -07001007 /* Channel Names ('A', 'B', etc.) */
1008 char channel;
1009 char channel_b;
1010
1011 /* Initiator Bus ID */
1012 uint8_t our_id;
1013 uint8_t our_id_b;
1014
1015 /*
1016 * PCI error detection.
1017 */
1018 int unsolicited_ints;
1019
1020 /*
1021 * Target incoming command FIFO.
1022 */
1023 struct target_cmd *targetcmds;
1024 uint8_t tqinfifonext;
1025
1026 /*
1027 * Cached copy of the sequencer control register.
1028 */
1029 uint8_t seqctl;
1030
1031 /*
1032 * Incoming and outgoing message handling.
1033 */
1034 uint8_t send_msg_perror;
1035 ahc_msg_type msg_type;
1036 uint8_t msgout_buf[12];/* Message we are sending */
1037 uint8_t msgin_buf[12];/* Message we are receiving */
1038 u_int msgout_len; /* Length of message to send */
1039 u_int msgout_index; /* Current index in msgout */
1040 u_int msgin_index; /* Current index in msgin */
1041
1042 /*
1043 * Mapping information for data structures shared
1044 * between the sequencer and kernel.
1045 */
1046 bus_dma_tag_t parent_dmat;
1047 bus_dma_tag_t shared_data_dmat;
1048 bus_dmamap_t shared_data_dmamap;
1049 dma_addr_t shared_data_busaddr;
1050
1051 /*
1052 * Bus address of the one byte buffer used to
1053 * work-around a DMA bug for chips <= aic7880
1054 * in target mode.
1055 */
1056 dma_addr_t dma_bug_buf;
1057
1058 /* Number of enabled target mode device on this card */
1059 u_int enabled_luns;
1060
1061 /* Initialization level of this data structure */
1062 u_int init_level;
1063
1064 /* PCI cacheline size. */
1065 u_int pci_cachesize;
1066
1067 /*
1068 * Count of parity errors we have seen as a target.
1069 * We auto-disable parity error checking after seeing
1070 * AHC_PCI_TARGET_PERR_THRESH number of errors.
1071 */
1072 u_int pci_target_perr_count;
1073#define AHC_PCI_TARGET_PERR_THRESH 10
1074
1075 /* Maximum number of sequencer instructions supported. */
1076 u_int instruction_ram_size;
1077
1078 /* Per-Unit descriptive information */
1079 const char *description;
1080 char *name;
1081 int unit;
1082
1083 /* Selection Timer settings */
1084 int seltime;
1085 int seltime_b;
1086
1087 uint16_t user_discenable;/* Disconnection allowed */
1088 uint16_t user_tagenable;/* Tagged Queuing allowed */
1089};
1090
Linus Torvalds1da177e2005-04-16 15:20:36 -07001091/************************ Active Device Information ***************************/
1092typedef enum {
1093 ROLE_UNKNOWN,
1094 ROLE_INITIATOR,
1095 ROLE_TARGET
1096} role_t;
1097
1098struct ahc_devinfo {
1099 int our_scsiid;
1100 int target_offset;
1101 uint16_t target_mask;
1102 u_int target;
1103 u_int lun;
1104 char channel;
1105 role_t role; /*
1106 * Only guaranteed to be correct if not
1107 * in the busfree state.
1108 */
1109};
1110
1111/****************************** PCI Structures ********************************/
1112typedef int (ahc_device_setup_t)(struct ahc_softc *);
1113
1114struct ahc_pci_identity {
1115 uint64_t full_id;
1116 uint64_t id_mask;
Denys Vlasenko980b3062008-04-25 04:36:01 +02001117 const char *name;
Linus Torvalds1da177e2005-04-16 15:20:36 -07001118 ahc_device_setup_t *setup;
1119};
Linus Torvalds1da177e2005-04-16 15:20:36 -07001120
1121/***************************** VL/EISA Declarations ***************************/
1122struct aic7770_identity {
1123 uint32_t full_id;
1124 uint32_t id_mask;
1125 const char *name;
1126 ahc_device_setup_t *setup;
1127};
1128extern struct aic7770_identity aic7770_ident_table[];
1129extern const int ahc_num_aic7770_devs;
1130
1131#define AHC_EISA_SLOT_OFFSET 0xc00
1132#define AHC_EISA_IOSIZE 0x100
1133
1134/*************************** Function Declarations ****************************/
1135/******************************************************************************/
Linus Torvalds1da177e2005-04-16 15:20:36 -07001136
1137/***************************** PCI Front End *********************************/
Denys Vlasenko980b3062008-04-25 04:36:01 +02001138const struct ahc_pci_identity *ahc_find_pci_device(ahc_dev_softc_t);
Linus Torvalds1da177e2005-04-16 15:20:36 -07001139int ahc_pci_config(struct ahc_softc *,
Denys Vlasenko980b3062008-04-25 04:36:01 +02001140 const struct ahc_pci_identity *);
Linus Torvalds1da177e2005-04-16 15:20:36 -07001141int ahc_pci_test_register_access(struct ahc_softc *);
FUJITA Tomonori03e79252008-01-27 00:08:19 +09001142#ifdef CONFIG_PM
Hannes Reineckeb5720722007-10-19 10:32:21 +02001143void ahc_pci_resume(struct ahc_softc *ahc);
FUJITA Tomonori03e79252008-01-27 00:08:19 +09001144#endif
Linus Torvalds1da177e2005-04-16 15:20:36 -07001145
1146/*************************** EISA/VL Front End ********************************/
1147struct aic7770_identity *aic7770_find_device(uint32_t);
1148int aic7770_config(struct ahc_softc *ahc,
1149 struct aic7770_identity *,
1150 u_int port);
1151
1152/************************** SCB and SCB queue management **********************/
1153int ahc_probe_scbs(struct ahc_softc *);
Linus Torvalds1da177e2005-04-16 15:20:36 -07001154void ahc_qinfifo_requeue_tail(struct ahc_softc *ahc,
1155 struct scb *scb);
1156int ahc_match_scb(struct ahc_softc *ahc, struct scb *scb,
1157 int target, char channel, int lun,
1158 u_int tag, role_t role);
1159
1160/****************************** Initialization ********************************/
1161struct ahc_softc *ahc_alloc(void *platform_arg, char *name);
1162int ahc_softc_init(struct ahc_softc *);
1163void ahc_controller_info(struct ahc_softc *ahc, char *buf);
1164int ahc_chip_init(struct ahc_softc *ahc);
1165int ahc_init(struct ahc_softc *ahc);
1166void ahc_intr_enable(struct ahc_softc *ahc, int enable);
1167void ahc_pause_and_flushwork(struct ahc_softc *ahc);
FUJITA Tomonori03e79252008-01-27 00:08:19 +09001168#ifdef CONFIG_PM
Linus Torvalds1da177e2005-04-16 15:20:36 -07001169int ahc_suspend(struct ahc_softc *ahc);
1170int ahc_resume(struct ahc_softc *ahc);
FUJITA Tomonori03e79252008-01-27 00:08:19 +09001171#endif
Linus Torvalds1da177e2005-04-16 15:20:36 -07001172void ahc_set_unit(struct ahc_softc *, int);
1173void ahc_set_name(struct ahc_softc *, char *);
Linus Torvalds1da177e2005-04-16 15:20:36 -07001174void ahc_free(struct ahc_softc *ahc);
1175int ahc_reset(struct ahc_softc *ahc, int reinit);
Linus Torvalds1da177e2005-04-16 15:20:36 -07001176
1177/***************************** Error Recovery *********************************/
1178typedef enum {
1179 SEARCH_COMPLETE,
1180 SEARCH_COUNT,
1181 SEARCH_REMOVE
1182} ahc_search_action;
1183int ahc_search_qinfifo(struct ahc_softc *ahc, int target,
1184 char channel, int lun, u_int tag,
1185 role_t role, uint32_t status,
1186 ahc_search_action action);
1187int ahc_search_untagged_queues(struct ahc_softc *ahc,
1188 ahc_io_ctx_t ctx,
1189 int target, char channel,
1190 int lun, uint32_t status,
1191 ahc_search_action action);
1192int ahc_search_disc_list(struct ahc_softc *ahc, int target,
1193 char channel, int lun, u_int tag,
1194 int stop_on_first, int remove,
1195 int save_state);
Linus Torvalds1da177e2005-04-16 15:20:36 -07001196int ahc_reset_channel(struct ahc_softc *ahc, char channel,
1197 int initiate_reset);
Denys Vlasenkod1d7b192008-04-25 04:34:49 +02001198
Linus Torvalds1da177e2005-04-16 15:20:36 -07001199/*************************** Utility Functions ********************************/
Linus Torvalds1da177e2005-04-16 15:20:36 -07001200void ahc_compile_devinfo(struct ahc_devinfo *devinfo,
1201 u_int our_id, u_int target,
1202 u_int lun, char channel,
1203 role_t role);
1204/************************** Transfer Negotiation ******************************/
Denys Vlasenkod1d7b192008-04-25 04:34:49 +02001205const struct ahc_syncrate* ahc_find_syncrate(struct ahc_softc *ahc, u_int *period,
Linus Torvalds1da177e2005-04-16 15:20:36 -07001206 u_int *ppr_options, u_int maxsync);
1207u_int ahc_find_period(struct ahc_softc *ahc,
1208 u_int scsirate, u_int maxsync);
Linus Torvalds1da177e2005-04-16 15:20:36 -07001209/*
1210 * Negotiation types. These are used to qualify if we should renegotiate
1211 * even if our goal and current transport parameters are identical.
1212 */
1213typedef enum {
1214 AHC_NEG_TO_GOAL, /* Renegotiate only if goal and curr differ. */
1215 AHC_NEG_IF_NON_ASYNC, /* Renegotiate so long as goal is non-async. */
1216 AHC_NEG_ALWAYS /* Renegotiat even if goal is async. */
1217} ahc_neg_type;
1218int ahc_update_neg_request(struct ahc_softc*,
1219 struct ahc_devinfo*,
1220 struct ahc_tmode_tstate*,
1221 struct ahc_initiator_tinfo*,
1222 ahc_neg_type);
1223void ahc_set_width(struct ahc_softc *ahc,
1224 struct ahc_devinfo *devinfo,
1225 u_int width, u_int type, int paused);
1226void ahc_set_syncrate(struct ahc_softc *ahc,
1227 struct ahc_devinfo *devinfo,
Denys Vlasenkod1d7b192008-04-25 04:34:49 +02001228 const struct ahc_syncrate *syncrate,
Linus Torvalds1da177e2005-04-16 15:20:36 -07001229 u_int period, u_int offset,
1230 u_int ppr_options,
1231 u_int type, int paused);
1232typedef enum {
1233 AHC_QUEUE_NONE,
1234 AHC_QUEUE_BASIC,
1235 AHC_QUEUE_TAGGED
1236} ahc_queue_alg;
1237
Linus Torvalds1da177e2005-04-16 15:20:36 -07001238/**************************** Target Mode *************************************/
1239#ifdef AHC_TARGET_MODE
1240void ahc_send_lstate_events(struct ahc_softc *,
1241 struct ahc_tmode_lstate *);
1242void ahc_handle_en_lun(struct ahc_softc *ahc,
1243 struct cam_sim *sim, union ccb *ccb);
1244cam_status ahc_find_tmode_devs(struct ahc_softc *ahc,
1245 struct cam_sim *sim, union ccb *ccb,
1246 struct ahc_tmode_tstate **tstate,
1247 struct ahc_tmode_lstate **lstate,
1248 int notfound_failure);
1249#ifndef AHC_TMODE_ENABLE
1250#define AHC_TMODE_ENABLE 0
1251#endif
1252#endif
1253/******************************* Debug ***************************************/
1254#ifdef AHC_DEBUG
1255extern uint32_t ahc_debug;
1256#define AHC_SHOW_MISC 0x0001
1257#define AHC_SHOW_SENSE 0x0002
1258#define AHC_DUMP_SEEPROM 0x0004
1259#define AHC_SHOW_TERMCTL 0x0008
1260#define AHC_SHOW_MEMORY 0x0010
1261#define AHC_SHOW_MESSAGES 0x0020
1262#define AHC_SHOW_DV 0x0040
1263#define AHC_SHOW_SELTO 0x0080
1264#define AHC_SHOW_QFULL 0x0200
1265#define AHC_SHOW_QUEUE 0x0400
1266#define AHC_SHOW_TQIN 0x0800
1267#define AHC_SHOW_MASKED_ERRORS 0x1000
1268#define AHC_DEBUG_SEQUENCER 0x2000
1269#endif
Linus Torvalds1da177e2005-04-16 15:20:36 -07001270void ahc_print_devinfo(struct ahc_softc *ahc,
1271 struct ahc_devinfo *dev);
1272void ahc_dump_card_state(struct ahc_softc *ahc);
Denys Vlasenkod1d7b192008-04-25 04:34:49 +02001273int ahc_print_register(const ahc_reg_parse_entry_t *table,
Linus Torvalds1da177e2005-04-16 15:20:36 -07001274 u_int num_entries,
1275 const char *name,
1276 u_int address,
1277 u_int value,
1278 u_int *cur_column,
1279 u_int wrap_point);
1280/******************************* SEEPROM *************************************/
1281int ahc_acquire_seeprom(struct ahc_softc *ahc,
1282 struct seeprom_descriptor *sd);
1283void ahc_release_seeprom(struct seeprom_descriptor *sd);
1284#endif /* _AIC7XXX_H_ */