blob: b07ba1924de0b907ef5bdd6c298d5a83edd8b375 [file] [log] [blame]
Linus Torvalds1da177e2005-04-16 15:20:36 -07001/* e2100.c: A Cabletron E2100 series ethernet driver for linux. */
2/*
3 Written 1993-1994 by Donald Becker.
4
5 Copyright 1994 by Donald Becker.
6 Copyright 1993 United States Government as represented by the
7 Director, National Security Agency. This software may be used and
8 distributed according to the terms of the GNU General Public License,
9 incorporated herein by reference.
10
11 This is a driver for the Cabletron E2100 series ethercards.
12
13 The Author may be reached as becker@scyld.com, or C/O
14 Scyld Computing Corporation
15 410 Severn Ave., Suite 210
16 Annapolis MD 21403
17
18 The E2100 series ethercard is a fairly generic shared memory 8390
19 implementation. The only unusual aspect is the way the shared memory
20 registers are set: first you do an inb() in what is normally the
21 station address region, and the low three bits of next outb() *address*
22 is used as the write value for that register. Either someone wasn't
23 too used to dem bit en bites, or they were trying to obfuscate the
24 programming interface.
25
26 There is an additional complication when setting the window on the packet
27 buffer. You must first do a read into the packet buffer region with the
28 low 8 address bits the address setting the page for the start of the packet
29 buffer window, and then do the above operation. See mem_on() for details.
30
31 One bug on the chip is that even a hard reset won't disable the memory
32 window, usually resulting in a hung machine if mem_off() isn't called.
33 If this happens, you must power down the machine for about 30 seconds.
34*/
35
36static const char version[] =
37 "e2100.c:v1.01 7/21/94 Donald Becker (becker@cesdis.gsfc.nasa.gov)\n";
38
39#include <linux/module.h>
40#include <linux/kernel.h>
41#include <linux/errno.h>
42#include <linux/string.h>
43#include <linux/ioport.h>
44#include <linux/netdevice.h>
45#include <linux/etherdevice.h>
46#include <linux/init.h>
47#include <linux/delay.h>
48
49#include <asm/io.h>
50#include <asm/system.h>
51
52#include "8390.h"
53
54#define DRV_NAME "e2100"
55
56static int e21_probe_list[] = {0x300, 0x280, 0x380, 0x220, 0};
57
58/* Offsets from the base_addr.
59 Read from the ASIC register, and the low three bits of the next outb()
60 address is used to set the corresponding register. */
61#define E21_NIC_OFFSET 0 /* Offset to the 8390 NIC. */
62#define E21_ASIC 0x10
63#define E21_MEM_ENABLE 0x10
64#define E21_MEM_ON 0x05 /* Enable memory in 16 bit mode. */
65#define E21_MEM_ON_8 0x07 /* Enable memory in 8 bit mode. */
66#define E21_MEM_BASE 0x11
67#define E21_IRQ_LOW 0x12 /* The low three bits of the IRQ number. */
68#define E21_IRQ_HIGH 0x14 /* The high IRQ bit and media select ... */
69#define E21_MEDIA 0x14 /* (alias). */
70#define E21_ALT_IFPORT 0x02 /* Set to use the other (BNC,AUI) port. */
71#define E21_BIG_MEM 0x04 /* Use a bigger (64K) buffer (we don't) */
72#define E21_SAPROM 0x10 /* Offset to station address data. */
73#define E21_IO_EXTENT 0x20
74
75static inline void mem_on(short port, volatile char __iomem *mem_base,
76 unsigned char start_page )
77{
78 /* This is a little weird: set the shared memory window by doing a
79 read. The low address bits specify the starting page. */
80 readb(mem_base+start_page);
81 inb(port + E21_MEM_ENABLE);
82 outb(E21_MEM_ON, port + E21_MEM_ENABLE + E21_MEM_ON);
83}
84
85static inline void mem_off(short port)
86{
87 inb(port + E21_MEM_ENABLE);
88 outb(0x00, port + E21_MEM_ENABLE);
89}
90
91/* In other drivers I put the TX pages first, but the E2100 window circuitry
92 is designed to have a 4K Tx region last. The windowing circuitry wraps the
93 window at 0x2fff->0x0000 so that the packets at e.g. 0x2f00 in the RX ring
94 appear contiguously in the window. */
95#define E21_RX_START_PG 0x00 /* First page of RX buffer */
96#define E21_RX_STOP_PG 0x30 /* Last page +1 of RX ring */
97#define E21_BIG_RX_STOP_PG 0xF0 /* Last page +1 of RX ring */
98#define E21_TX_START_PG E21_RX_STOP_PG /* First page of TX buffer */
99
100static int e21_probe1(struct net_device *dev, int ioaddr);
101
102static int e21_open(struct net_device *dev);
103static void e21_reset_8390(struct net_device *dev);
104static void e21_block_input(struct net_device *dev, int count,
105 struct sk_buff *skb, int ring_offset);
106static void e21_block_output(struct net_device *dev, int count,
107 const unsigned char *buf, int start_page);
108static void e21_get_8390_hdr(struct net_device *dev, struct e8390_pkt_hdr *hdr,
109 int ring_page);
Stephen Hemminger8284abe2008-11-25 18:24:20 -0800110static int e21_open(struct net_device *dev);
Linus Torvalds1da177e2005-04-16 15:20:36 -0700111static int e21_close(struct net_device *dev);
112
Jeff Garzik6aa20a22006-09-13 13:24:59 -0400113
Linus Torvalds1da177e2005-04-16 15:20:36 -0700114/* Probe for the E2100 series ethercards. These cards have an 8390 at the
115 base address and the station address at both offset 0x10 and 0x18. I read
116 the station address from offset 0x18 to avoid the dataport of NE2000
117 ethercards, and look for Ctron's unique ID (first three octets of the
118 station address).
119 */
120
121static int __init do_e2100_probe(struct net_device *dev)
122{
123 int *port;
124 int base_addr = dev->base_addr;
125 int irq = dev->irq;
126
Linus Torvalds1da177e2005-04-16 15:20:36 -0700127 if (base_addr > 0x1ff) /* Check a single specified location. */
128 return e21_probe1(dev, base_addr);
129 else if (base_addr != 0) /* Don't probe at all. */
130 return -ENXIO;
131
132 for (port = e21_probe_list; *port; port++) {
133 dev->irq = irq;
134 if (e21_probe1(dev, *port) == 0)
135 return 0;
136 }
137
138 return -ENODEV;
139}
140
Linus Torvalds1da177e2005-04-16 15:20:36 -0700141#ifndef MODULE
142struct net_device * __init e2100_probe(int unit)
143{
144 struct net_device *dev = alloc_ei_netdev();
145 int err;
146
147 if (!dev)
148 return ERR_PTR(-ENOMEM);
149
150 sprintf(dev->name, "eth%d", unit);
151 netdev_boot_setup_check(dev);
152
153 err = do_e2100_probe(dev);
154 if (err)
155 goto out;
Linus Torvalds1da177e2005-04-16 15:20:36 -0700156 return dev;
Linus Torvalds1da177e2005-04-16 15:20:36 -0700157out:
158 free_netdev(dev);
159 return ERR_PTR(err);
160}
161#endif
162
Stephen Hemminger8284abe2008-11-25 18:24:20 -0800163static const struct net_device_ops e21_netdev_ops = {
164 .ndo_open = e21_open,
165 .ndo_stop = e21_close,
166
167 .ndo_start_xmit = ei_start_xmit,
168 .ndo_tx_timeout = ei_tx_timeout,
169 .ndo_get_stats = ei_get_stats,
170 .ndo_set_multicast_list = ei_set_multicast_list,
171 .ndo_validate_addr = eth_validate_addr,
Stephen Hemmingerfe96aaa2009-01-09 11:13:14 +0000172 .ndo_set_mac_address = eth_mac_addr,
Stephen Hemminger8284abe2008-11-25 18:24:20 -0800173 .ndo_change_mtu = eth_change_mtu,
174#ifdef CONFIG_NET_POLL_CONTROLLER
175 .ndo_poll_controller = ei_poll,
176#endif
177};
178
Linus Torvalds1da177e2005-04-16 15:20:36 -0700179static int __init e21_probe1(struct net_device *dev, int ioaddr)
180{
181 int i, status, retval;
182 unsigned char *station_addr = dev->dev_addr;
183 static unsigned version_printed;
184
185 if (!request_region(ioaddr, E21_IO_EXTENT, DRV_NAME))
186 return -EBUSY;
187
188 /* First check the station address for the Ctron prefix. */
189 if (inb(ioaddr + E21_SAPROM + 0) != 0x00
190 || inb(ioaddr + E21_SAPROM + 1) != 0x00
191 || inb(ioaddr + E21_SAPROM + 2) != 0x1d) {
192 retval = -ENODEV;
193 goto out;
194 }
195
196 /* Verify by making certain that there is a 8390 at there. */
197 outb(E8390_NODMA + E8390_STOP, ioaddr);
198 udelay(1); /* we want to delay one I/O cycle - which is 2MHz */
199 status = inb(ioaddr);
200 if (status != 0x21 && status != 0x23) {
201 retval = -ENODEV;
202 goto out;
203 }
204
205 /* Read the station address PROM. */
206 for (i = 0; i < 6; i++)
207 station_addr[i] = inb(ioaddr + E21_SAPROM + i);
208
209 inb(ioaddr + E21_MEDIA); /* Point to media selection. */
210 outb(0, ioaddr + E21_ASIC); /* and disable the secondary interface. */
211
212 if (ei_debug && version_printed++ == 0)
213 printk(version);
214
215 for (i = 0; i < 6; i++)
216 printk(" %02X", station_addr[i]);
217
218 if (dev->irq < 2) {
219 int irqlist[] = {15,11,10,12,5,9,3,4}, i;
220 for (i = 0; i < 8; i++)
221 if (request_irq (irqlist[i], NULL, 0, "bogus", NULL) != -EBUSY) {
222 dev->irq = irqlist[i];
223 break;
224 }
225 if (i >= 8) {
226 printk(" unable to get IRQ %d.\n", dev->irq);
227 retval = -EAGAIN;
228 goto out;
229 }
230 } else if (dev->irq == 2) /* Fixup luser bogosity: IRQ2 is really IRQ9 */
231 dev->irq = 9;
232
233 /* The 8390 is at the base address. */
234 dev->base_addr = ioaddr;
235
236 ei_status.name = "E2100";
237 ei_status.word16 = 1;
238 ei_status.tx_start_page = E21_TX_START_PG;
239 ei_status.rx_start_page = E21_RX_START_PG;
240 ei_status.stop_page = E21_RX_STOP_PG;
241 ei_status.saved_irq = dev->irq;
242
243 /* Check the media port used. The port can be passed in on the
244 low mem_end bits. */
245 if (dev->mem_end & 15)
246 dev->if_port = dev->mem_end & 7;
247 else {
248 dev->if_port = 0;
249 inb(ioaddr + E21_MEDIA); /* Turn automatic media detection on. */
250 for(i = 0; i < 6; i++)
251 if (station_addr[i] != inb(ioaddr + E21_SAPROM + 8 + i)) {
252 dev->if_port = 1;
253 break;
254 }
255 }
256
257 /* Never map in the E21 shared memory unless you are actively using it.
258 Also, the shared memory has effective only one setting -- spread all
259 over the 128K region! */
260 if (dev->mem_start == 0)
261 dev->mem_start = 0xd0000;
262
263 ei_status.mem = ioremap(dev->mem_start, 2*1024);
264 if (!ei_status.mem) {
265 printk("unable to remap memory\n");
266 retval = -EAGAIN;
267 goto out;
268 }
269
270#ifdef notdef
271 /* These values are unused. The E2100 has a 2K window into the packet
272 buffer. The window can be set to start on any page boundary. */
273 ei_status.rmem_start = dev->mem_start + TX_PAGES*256;
274 dev->mem_end = ei_status.rmem_end = dev->mem_start + 2*1024;
275#endif
276
277 printk(", IRQ %d, %s media, memory @ %#lx.\n", dev->irq,
278 dev->if_port ? "secondary" : "primary", dev->mem_start);
279
280 ei_status.reset_8390 = &e21_reset_8390;
281 ei_status.block_input = &e21_block_input;
282 ei_status.block_output = &e21_block_output;
283 ei_status.get_8390_hdr = &e21_get_8390_hdr;
Stephen Hemminger8284abe2008-11-25 18:24:20 -0800284
285 dev->netdev_ops = &e21_netdev_ops;
Linus Torvalds1da177e2005-04-16 15:20:36 -0700286 NS8390_init(dev, 0);
287
b1fc5502005-05-12 20:11:55 -0400288 retval = register_netdev(dev);
289 if (retval)
290 goto out;
Linus Torvalds1da177e2005-04-16 15:20:36 -0700291 return 0;
292out:
293 release_region(ioaddr, E21_IO_EXTENT);
294 return retval;
295}
296
297static int
298e21_open(struct net_device *dev)
299{
300 short ioaddr = dev->base_addr;
301 int retval;
302
303 if ((retval = request_irq(dev->irq, ei_interrupt, 0, dev->name, dev)))
304 return retval;
305
306 /* Set the interrupt line and memory base on the hardware. */
307 inb(ioaddr + E21_IRQ_LOW);
308 outb(0, ioaddr + E21_ASIC + (dev->irq & 7));
309 inb(ioaddr + E21_IRQ_HIGH); /* High IRQ bit, and if_port. */
310 outb(0, ioaddr + E21_ASIC + (dev->irq > 7 ? 1:0)
311 + (dev->if_port ? E21_ALT_IFPORT : 0));
312 inb(ioaddr + E21_MEM_BASE);
313 outb(0, ioaddr + E21_ASIC + ((dev->mem_start >> 17) & 7));
314
315 ei_open(dev);
316 return 0;
317}
318
319static void
320e21_reset_8390(struct net_device *dev)
321{
322 short ioaddr = dev->base_addr;
323
324 outb(0x01, ioaddr);
325 if (ei_debug > 1) printk("resetting the E2180x3 t=%ld...", jiffies);
326 ei_status.txing = 0;
327
328 /* Set up the ASIC registers, just in case something changed them. */
329
330 if (ei_debug > 1) printk("reset done\n");
331 return;
332}
333
334/* Grab the 8390 specific header. We put the 2k window so the header page
335 appears at the start of the shared memory. */
336
337static void
338e21_get_8390_hdr(struct net_device *dev, struct e8390_pkt_hdr *hdr, int ring_page)
339{
340
341 short ioaddr = dev->base_addr;
342 char __iomem *shared_mem = ei_status.mem;
343
344 mem_on(ioaddr, shared_mem, ring_page);
345
346#ifdef notdef
347 /* Officially this is what we are doing, but the readl() is faster */
348 memcpy_fromio(hdr, shared_mem, sizeof(struct e8390_pkt_hdr));
349#else
350 ((unsigned int*)hdr)[0] = readl(shared_mem);
351#endif
352
353 /* Turn off memory access: we would need to reprogram the window anyway. */
354 mem_off(ioaddr);
355
356}
357
358/* Block input and output are easy on shared memory ethercards.
359 The E21xx makes block_input() especially easy by wrapping the top
360 ring buffer to the bottom automatically. */
361static void
362e21_block_input(struct net_device *dev, int count, struct sk_buff *skb, int ring_offset)
363{
364 short ioaddr = dev->base_addr;
365 char __iomem *shared_mem = ei_status.mem;
366
367 mem_on(ioaddr, shared_mem, (ring_offset>>8));
368
Al Viro4ec03112007-02-09 16:38:30 +0000369 memcpy_fromio(skb->data, ei_status.mem + (ring_offset & 0xff), count);
Linus Torvalds1da177e2005-04-16 15:20:36 -0700370
371 mem_off(ioaddr);
372}
373
374static void
375e21_block_output(struct net_device *dev, int count, const unsigned char *buf,
376 int start_page)
377{
378 short ioaddr = dev->base_addr;
379 volatile char __iomem *shared_mem = ei_status.mem;
380
381 /* Set the shared memory window start by doing a read, with the low address
382 bits specifying the starting page. */
383 readb(shared_mem + start_page);
384 mem_on(ioaddr, shared_mem, start_page);
385
386 memcpy_toio(shared_mem, buf, count);
387 mem_off(ioaddr);
388}
389
390static int
391e21_close(struct net_device *dev)
392{
393 short ioaddr = dev->base_addr;
394
395 if (ei_debug > 1)
396 printk("%s: Shutting down ethercard.\n", dev->name);
397
398 free_irq(dev->irq, dev);
399 dev->irq = ei_status.saved_irq;
400
401 /* Shut off the interrupt line and secondary interface. */
402 inb(ioaddr + E21_IRQ_LOW);
403 outb(0, ioaddr + E21_ASIC);
404 inb(ioaddr + E21_IRQ_HIGH); /* High IRQ bit, and if_port. */
405 outb(0, ioaddr + E21_ASIC);
406
407 ei_close(dev);
408
409 /* Double-check that the memory has been turned off, because really
410 really bad things happen if it isn't. */
411 mem_off(ioaddr);
412
413 return 0;
414}
415
Jeff Garzik6aa20a22006-09-13 13:24:59 -0400416
Linus Torvalds1da177e2005-04-16 15:20:36 -0700417#ifdef MODULE
418#define MAX_E21_CARDS 4 /* Max number of E21 cards per module */
419static struct net_device *dev_e21[MAX_E21_CARDS];
420static int io[MAX_E21_CARDS];
421static int irq[MAX_E21_CARDS];
422static int mem[MAX_E21_CARDS];
423static int xcvr[MAX_E21_CARDS]; /* choose int. or ext. xcvr */
424
425module_param_array(io, int, NULL, 0);
426module_param_array(irq, int, NULL, 0);
427module_param_array(mem, int, NULL, 0);
428module_param_array(xcvr, int, NULL, 0);
429MODULE_PARM_DESC(io, "I/O base address(es)");
430MODULE_PARM_DESC(irq, "IRQ number(s)");
431MODULE_PARM_DESC(mem, " memory base address(es)");
432MODULE_PARM_DESC(xcvr, "transceiver(s) (0=internal, 1=external)");
433MODULE_DESCRIPTION("Cabletron E2100 ISA ethernet driver");
434MODULE_LICENSE("GPL");
435
436/* This is set up so that only a single autoprobe takes place per call.
437ISA device autoprobes on a running machine are not recommended. */
Andrew Mortond543cbb2006-08-14 23:00:00 -0700438
439int __init init_module(void)
Linus Torvalds1da177e2005-04-16 15:20:36 -0700440{
441 struct net_device *dev;
442 int this_dev, found = 0;
443
444 for (this_dev = 0; this_dev < MAX_E21_CARDS; this_dev++) {
445 if (io[this_dev] == 0) {
446 if (this_dev != 0) break; /* only autoprobe 1st one */
447 printk(KERN_NOTICE "e2100.c: Presently autoprobing (not recommended) for a single card.\n");
448 }
449 dev = alloc_ei_netdev();
450 if (!dev)
451 break;
452 dev->irq = irq[this_dev];
453 dev->base_addr = io[this_dev];
454 dev->mem_start = mem[this_dev];
455 dev->mem_end = xcvr[this_dev]; /* low 4bits = xcvr sel. */
456 if (do_e2100_probe(dev) == 0) {
b1fc5502005-05-12 20:11:55 -0400457 dev_e21[found++] = dev;
458 continue;
Linus Torvalds1da177e2005-04-16 15:20:36 -0700459 }
460 free_netdev(dev);
461 printk(KERN_WARNING "e2100.c: No E2100 card found (i/o = 0x%x).\n", io[this_dev]);
462 break;
463 }
464 if (found)
465 return 0;
466 return -ENXIO;
467}
468
Denis Vlasenko64916f12006-01-05 22:45:47 -0800469static void cleanup_card(struct net_device *dev)
470{
471 /* NB: e21_close() handles free_irq */
472 iounmap(ei_status.mem);
473 release_region(dev->base_addr, E21_IO_EXTENT);
474}
475
Al Viroafc8eb42006-06-14 18:50:53 -0400476void __exit
Linus Torvalds1da177e2005-04-16 15:20:36 -0700477cleanup_module(void)
478{
479 int this_dev;
480
481 for (this_dev = 0; this_dev < MAX_E21_CARDS; this_dev++) {
482 struct net_device *dev = dev_e21[this_dev];
483 if (dev) {
484 unregister_netdev(dev);
485 cleanup_card(dev);
486 free_netdev(dev);
487 }
488 }
489}
490#endif /* MODULE */