drivers/input/keyboard/Kconfig

#
# Input core configuration
#
menuconfig INPUT_KEYBOARD
	bool "Keyboards" if EMBEDDED || !X86
	default y
	help
	  Say Y here, and a list of supported keyboards will be displayed.
	  This option doesn't affect the kernel.

	  If unsure, say Y.

if INPUT_KEYBOARD

config KEYBOARD_ATKBD
	tristate "AT keyboard" if !PC
	default y
	select SERIO
	select SERIO_LIBPS2
	select SERIO_I8042 if PC
	select SERIO_GSCPS2 if GSC
	help
	  Say Y here if you want to use a standard AT or PS/2 keyboard. Usually
	  you'll need this, unless you have a different type keyboard (USB, ADB
	  or other). This also works for AT and PS/2 keyboards connected over a
	  PS/2 to serial converter.

	  If unsure, say Y.

	  To compile this driver as a module, choose M here: the
	  module will be called atkbd.

config KEYBOARD_ATKBD_HP_KEYCODES
	bool "Use HP keyboard scancodes"
	depends on PARISC && KEYBOARD_ATKBD
	default y
	help
	  Say Y here if you have a PA-RISC machine and want to use an AT or
	  PS/2 keyboard, and your keyboard uses keycodes that are specific to
	  PA-RISC keyboards.

	  Say N if you use a standard keyboard.

config KEYBOARD_ATKBD_RDI_KEYCODES
	bool "Use PrecisionBook keyboard scancodes"
	depends on KEYBOARD_ATKBD_HP_KEYCODES
	default n
	help
	  If you have an RDI PrecisionBook, say Y here if you want to use its
	  built-in keyboard (as opposed to an external keyboard).

	  The PrecisionBook has five keys that conflict with those used by most
	  AT and PS/2 keyboards. These are as follows:

	    PrecisionBook    Standard AT or PS/2

	    F1               F12
	    Left Ctrl        Left Alt
	    Caps Lock        Left Ctrl
	    Right Ctrl       Caps Lock
	    Left             102nd key (the key to the right of Left Shift)

	  If you say N here, and use the PrecisionBook keyboard, then each key
	  in the left-hand column will be interpreted as the corresponding key
	  in the right-hand column.

	  If you say Y here, and use an external keyboard, then each key in the
	  right-hand column will be interpreted as the key shown in the
	  left-hand column.

config KEYBOARD_SUNKBD
	tristate "Sun Type 4 and Type 5 keyboard"
	select SERIO
	help
	  Say Y here if you want to use a Sun Type 4 or Type 5 keyboard,
	  connected either to the Sun keyboard connector or to an serial
	  (RS-232) port via a simple adapter.

	  To compile this driver as a module, choose M here: the
	  module will be called sunkbd.

config KEYBOARD_LKKBD
	tristate "DECstation/VAXstation LK201/LK401 keyboard"
	select SERIO
	help
	  Say Y here if you want to use a LK201 or LK401 style serial
	  keyboard. This keyboard is also useable on PCs if you attach
	  it with the inputattach program. The connector pinout is
	  described within lkkbd.c.

	  To compile this driver as a module, choose M here: the
	  module will be called lkkbd.

config KEYBOARD_LOCOMO
	tristate "LoCoMo Keyboard Support"
	depends on SHARP_LOCOMO
	help
	  Say Y here if you are running Linux on a Sharp Zaurus Collie or Poodle based PDA

	  To compile this driver as a module, choose M here: the
	  module will be called locomokbd.

config KEYBOARD_XTKBD
	tristate "XT keyboard"
	select SERIO
	help
	  Say Y here if you want to use the old IBM PC/XT keyboard (or
	  compatible) on your system. This is only possible with a
	  parallel port keyboard adapter, you cannot connect it to the
	  keyboard port on a PC that runs Linux.

	  To compile this driver as a module, choose M here: the
	  module will be called xtkbd.

config KEYBOARD_NEWTON
	tristate "Newton keyboard"
	select SERIO
	help
	  Say Y here if you have a Newton keyboard on a serial port.

	  To compile this driver as a module, choose M here: the
	  module will be called newtonkbd.

config KEYBOARD_CORGI
	tristate "Corgi keyboard"
	depends on PXA_SHARPSL
	default y	
	help
	  Say Y here to enable the keyboard on the Sharp Zaurus SL-C7xx 
	  series of PDAs.

	  To compile this driver as a module, choose M here: the 
	  module will be called corgikbd.

config KEYBOARD_SPITZ
	tristate "Spitz keyboard"
	depends on PXA_SHARPSL
	default y
	help
	  Say Y here to enable the keyboard on the Sharp Zaurus SL-C1000,
	  SL-C3000 and Sl-C3100 series of PDAs.

	  To compile this driver as a module, choose M here: the
	  module will be called spitzkbd.

config KEYBOARD_MAPLE
	tristate "Maple bus keyboard"
	depends on SH_DREAMCAST && MAPLE
	help
	  Say Y here if you have a DreamCast console running Linux and have
	  a keyboard attached to its Maple bus.

	  To compile this driver as a module, choose M here: the
	  module will be called maple_keyb.

config KEYBOARD_AMIGA
	tristate "Amiga keyboard"
	depends on AMIGA
	help
	  Say Y here if you are running Linux on any AMIGA and have a keyboard
	  attached.

	  To compile this driver as a module, choose M here: the
	  module will be called amikbd.

config KEYBOARD_HIL_OLD
	tristate "HP HIL keyboard support (simple driver)"
	depends on GSC
	default y
	help
	  The "Human Interface Loop" is a older, 8-channel USB-like
	  controller used in several Hewlett Packard models. This driver
	  was adapted from the one written for m68k/hp300, and implements
	  support for a keyboard attached to the HIL port, but not for
	  any other types of HIL input devices like mice or tablets.
	  However, it has been thoroughly tested and is stable.

	  If you want full HIL support including support for multiple
	  keyboards, mices and tablets, you have to enable the
	  "HP System Device Controller i8042 Support" in the input/serio
	  submenu.

config KEYBOARD_HIL
	tristate "HP HIL keyboard support"
	depends on GSC
	default y
	select HP_SDC
	select HIL_MLC
	select SERIO
	help
	  The "Human Interface Loop" is a older, 8-channel USB-like
	  controller used in several Hewlett Packard models.
	  This driver implements support for HIL-keyboards attached
	  to your machine, so normally you should say Y here.

endif