blob: 9c8c6d914ec79788a367082663d60c9a51865148 [file] [log] [blame]
Linus Torvalds1da177e2005-04-16 15:20:36 -07001$Id: INTERFACE.fax,v 1.2 2000/08/06 09:22:50 armin Exp $
2
3
4Description of the fax-subinterface between linklevel and hardwarelevel of
5 isdn4linux.
6
7 The communication between linklevel (LL) and hardwarelevel (HL) for fax
8 is based on the struct T30_s (defined in isdnif.h).
9 This struct is allocated in the LL.
10 In order to use fax, the LL provides the pointer to this struct with the
11 command ISDN_CMD_SETL3 (parm.fax). This pointer expires in case of hangup
12 and when a new channel to a new connection is assigned.
13
14
15Data handling:
16 In send-mode the HL-driver has to handle the <DLE> codes and the bit-order
17 conversion by itself.
18 In receive-mode the LL-driver takes care of the bit-order conversion
19 (specified by +FBOR)
20
21Structure T30_s description:
22
23 This structure stores the values (set by AT-commands), the remote-
24 capability-values and the command-codes between LL and HL.
25
26 If the HL-driver receives ISDN_CMD_FAXCMD, all needed information
27 is in this struct set by the LL.
28 To signal information to the LL, the HL-driver has to set the
Paolo Ornati670e9f32006-10-03 22:57:56 +020029 parameters and use ISDN_STAT_FAXIND.
Linus Torvalds1da177e2005-04-16 15:20:36 -070030 (Please refer to INTERFACE)
31
32Structure T30_s:
33
34 All members are 8-bit unsigned (__u8)
35
36 - resolution
37 - rate
38 - width
39 - length
40 - compression
41 - ecm
42 - binary
43 - scantime
44 - id[]
45 Local faxmachine's parameters, set by +FDIS, +FDCS, +FLID, ...
46
47 - r_resolution
48 - r_rate
49 - r_width
50 - r_length
51 - r_compression
52 - r_ecm
53 - r_binary
54 - r_scantime
55 - r_id[]
56 Remote faxmachine's parameters. To be set by HL-driver.
57
58 - phase
59 Defines the actual state of fax connection. Set by HL or LL
60 depending on progress and type of connection.
61 If the phase changes because of an AT command, the LL driver
62 changes this value. Otherwise the HL-driver takes care of it, but
63 only necessary on call establishment (from IDLE to PHASE_A).
64 (one of the constants ISDN_FAX_PHASE_[IDLE,A,B,C,D,E])
65
66 - direction
67 Defines outgoing/send or incoming/receive connection.
68 (ISDN_TTY_FAX_CONN_[IN,OUT])
69
70 - code
71 Commands from LL to HL; possible constants :
72 ISDN_TTY_FAX_DR signals +FDR command to HL
73
74 ISDN_TTY_FAX_DT signals +FDT command to HL
75
76 ISDN_TTY_FAX_ET signals +FET command to HL
77
78
79 Other than that the "code" is set with the hangup-code value at
80 the end of connection for the +FHNG message.
81
82 - r_code
83 Commands from HL to LL; possible constants :
84 ISDN_TTY_FAX_CFR output of +FCFR message.
85
86 ISDN_TTY_FAX_RID output of remote ID set in r_id[]
87 (+FCSI/+FTSI on send/receive)
88
89 ISDN_TTY_FAX_DCS output of +FDCS and CONNECT message,
90 switching to phase C.
91
92 ISDN_TTY_FAX_ET signals end of data,
93 switching to phase D.
94
95 ISDN_TTY_FAX_FCON signals the established, outgoing connection,
96 switching to phase B.
97
98 ISDN_TTY_FAX_FCON_I signals the established, incoming connection,
99 switching to phase B.
100
101 ISDN_TTY_FAX_DIS output of +FDIS message and values.
102
103 ISDN_TTY_FAX_SENT signals that all data has been sent
104 and <DLE><ETX> is acknowledged,
105 OK message will be sent.
106
107 ISDN_TTY_FAX_PTS signals a msg-confirmation (page sent successful),
108 depending on fet value:
109 0: output OK message (more pages follow)
110 1: switching to phase B (next document)
111
112 ISDN_TTY_FAX_TRAIN_OK output of +FDCS and OK message (for receive mode).
113
114 ISDN_TTY_FAX_EOP signals end of data in receive mode,
115 switching to phase D.
116
117 ISDN_TTY_FAX_HNG output of the +FHNG and value set by code and
118 OK message, switching to phase E.
119
120
121 - badlin
122 Value of +FBADLIN
123
124 - badmul
125 Value of +FBADMUL
126
127 - bor
128 Value of +FBOR
129
130 - fet
131 Value of +FET command in send-mode.
132 Set by HL in receive-mode for +FET message.
133
134 - pollid[]
135 ID-string, set by +FCIG
136
137 - cq
138 Value of +FCQ
139
140 - cr
141 Value of +FCR
142
143 - ctcrty
144 Value of +FCTCRTY
145
146 - minsp
147 Value of +FMINSP
148
149 - phcto
150 Value of +FPHCTO
151
152 - rel
153 Value of +FREL
154
155 - nbc
156 Value of +FNBC (0,1)
157 (+FNBC is not a known class 2 fax command, I added this to change the
158 automatic "best capabilities" connection in the eicon HL-driver)
159
160
161Armin
162mac@melware.de
163