| /* |
| * QLogic Fibre Channel HBA Driver |
| * Copyright (c) 2003-2014 QLogic Corporation |
| * |
| * See LICENSE.qla2xxx for copyright and licensing details. |
| */ |
| #ifndef __QLA_FW_H |
| #define __QLA_FW_H |
| |
| #include <linux/nvme.h> |
| #include <linux/nvme-fc.h> |
| |
| #define MBS_CHECKSUM_ERROR 0x4010 |
| #define MBS_INVALID_PRODUCT_KEY 0x4020 |
| |
| /* |
| * Firmware Options. |
| */ |
| #define FO1_ENABLE_PUREX BIT_10 |
| #define FO1_DISABLE_LED_CTRL BIT_6 |
| #define FO1_ENABLE_8016 BIT_0 |
| #define FO2_ENABLE_SEL_CLASS2 BIT_5 |
| #define FO3_NO_ABTS_ON_LINKDOWN BIT_14 |
| #define FO3_HOLD_STS_IOCB BIT_12 |
| |
| /* |
| * Port Database structure definition for ISP 24xx. |
| */ |
| #define PDO_FORCE_ADISC BIT_1 |
| #define PDO_FORCE_PLOGI BIT_0 |
| |
| |
| #define PORT_DATABASE_24XX_SIZE 64 |
| struct port_database_24xx { |
| uint16_t flags; |
| #define PDF_TASK_RETRY_ID BIT_14 |
| #define PDF_FC_TAPE BIT_7 |
| #define PDF_ACK0_CAPABLE BIT_6 |
| #define PDF_FCP2_CONF BIT_5 |
| #define PDF_CLASS_2 BIT_4 |
| #define PDF_HARD_ADDR BIT_1 |
| |
| /* |
| * for NVMe, the login_state field has been |
| * split into nibbles. |
| * The lower nibble is for FCP. |
| * The upper nibble is for NVMe. |
| */ |
| uint8_t current_login_state; |
| uint8_t last_login_state; |
| #define PDS_PLOGI_PENDING 0x03 |
| #define PDS_PLOGI_COMPLETE 0x04 |
| #define PDS_PRLI_PENDING 0x05 |
| #define PDS_PRLI_COMPLETE 0x06 |
| #define PDS_PORT_UNAVAILABLE 0x07 |
| #define PDS_PRLO_PENDING 0x09 |
| #define PDS_LOGO_PENDING 0x11 |
| #define PDS_PRLI2_PENDING 0x12 |
| |
| uint8_t hard_address[3]; |
| uint8_t reserved_1; |
| |
| uint8_t port_id[3]; |
| uint8_t sequence_id; |
| |
| uint16_t port_timer; |
| |
| uint16_t nport_handle; /* N_PORT handle. */ |
| |
| uint16_t receive_data_size; |
| uint16_t reserved_2; |
| |
| uint8_t prli_svc_param_word_0[2]; /* Big endian */ |
| /* Bits 15-0 of word 0 */ |
| uint8_t prli_svc_param_word_3[2]; /* Big endian */ |
| /* Bits 15-0 of word 3 */ |
| |
| uint8_t port_name[WWN_SIZE]; |
| uint8_t node_name[WWN_SIZE]; |
| |
| uint8_t reserved_3[4]; |
| uint16_t prli_nvme_svc_param_word_0; /* Bits 15-0 of word 0 */ |
| uint16_t prli_nvme_svc_param_word_3; /* Bits 15-0 of word 3 */ |
| uint16_t nvme_first_burst_size; |
| uint8_t reserved_4[14]; |
| }; |
| |
| /* |
| * MB 75h returns a list of DB entries similar to port_database_24xx(64B). |
| * However, in this case it returns 1st 40 bytes. |
| */ |
| struct get_name_list_extended { |
| __le16 flags; |
| u8 current_login_state; |
| u8 last_login_state; |
| u8 hard_address[3]; |
| u8 reserved_1; |
| u8 port_id[3]; |
| u8 sequence_id; |
| __le16 port_timer; |
| __le16 nport_handle; /* N_PORT handle. */ |
| __le16 receive_data_size; |
| __le16 reserved_2; |
| |
| /* PRLI SVC Param are Big endian */ |
| u8 prli_svc_param_word_0[2]; /* Bits 15-0 of word 0 */ |
| u8 prli_svc_param_word_3[2]; /* Bits 15-0 of word 3 */ |
| u8 port_name[WWN_SIZE]; |
| u8 node_name[WWN_SIZE]; |
| }; |
| |
| /* MB 75h: This is the short version of the database */ |
| struct get_name_list { |
| u8 port_node_name[WWN_SIZE]; /* B7 most sig, B0 least sig */ |
| __le16 nport_handle; |
| u8 reserved; |
| }; |
| |
| struct vp_database_24xx { |
| uint16_t vp_status; |
| uint8_t options; |
| uint8_t id; |
| uint8_t port_name[WWN_SIZE]; |
| uint8_t node_name[WWN_SIZE]; |
| uint16_t port_id_low; |
| uint16_t port_id_high; |
| }; |
| |
| struct nvram_24xx { |
| /* NVRAM header. */ |
| uint8_t id[4]; |
| uint16_t nvram_version; |
| uint16_t reserved_0; |
| |
| /* Firmware Initialization Control Block. */ |
| uint16_t version; |
| uint16_t reserved_1; |
| __le16 frame_payload_size; |
| uint16_t execution_throttle; |
| uint16_t exchange_count; |
| uint16_t hard_address; |
| |
| uint8_t port_name[WWN_SIZE]; |
| uint8_t node_name[WWN_SIZE]; |
| |
| uint16_t login_retry_count; |
| uint16_t link_down_on_nos; |
| uint16_t interrupt_delay_timer; |
| uint16_t login_timeout; |
| |
| uint32_t firmware_options_1; |
| uint32_t firmware_options_2; |
| uint32_t firmware_options_3; |
| |
| /* Offset 56. */ |
| |
| /* |
| * BIT 0 = Control Enable |
| * BIT 1-15 = |
| * |
| * BIT 0-7 = Reserved |
| * BIT 8-10 = Output Swing 1G |
| * BIT 11-13 = Output Emphasis 1G |
| * BIT 14-15 = Reserved |
| * |
| * BIT 0-7 = Reserved |
| * BIT 8-10 = Output Swing 2G |
| * BIT 11-13 = Output Emphasis 2G |
| * BIT 14-15 = Reserved |
| * |
| * BIT 0-7 = Reserved |
| * BIT 8-10 = Output Swing 4G |
| * BIT 11-13 = Output Emphasis 4G |
| * BIT 14-15 = Reserved |
| */ |
| uint16_t seriallink_options[4]; |
| |
| uint16_t reserved_2[16]; |
| |
| /* Offset 96. */ |
| uint16_t reserved_3[16]; |
| |
| /* PCIe table entries. */ |
| uint16_t reserved_4[16]; |
| |
| /* Offset 160. */ |
| uint16_t reserved_5[16]; |
| |
| /* Offset 192. */ |
| uint16_t reserved_6[16]; |
| |
| /* Offset 224. */ |
| uint16_t reserved_7[16]; |
| |
| /* |
| * BIT 0 = Enable spinup delay |
| * BIT 1 = Disable BIOS |
| * BIT 2 = Enable Memory Map BIOS |
| * BIT 3 = Enable Selectable Boot |
| * BIT 4 = Disable RISC code load |
| * BIT 5 = Disable Serdes |
| * BIT 6 = |
| * BIT 7 = |
| * |
| * BIT 8 = |
| * BIT 9 = |
| * BIT 10 = Enable lip full login |
| * BIT 11 = Enable target reset |
| * BIT 12 = |
| * BIT 13 = |
| * BIT 14 = |
| * BIT 15 = Enable alternate WWN |
| * |
| * BIT 16-31 = |
| */ |
| uint32_t host_p; |
| |
| uint8_t alternate_port_name[WWN_SIZE]; |
| uint8_t alternate_node_name[WWN_SIZE]; |
| |
| uint8_t boot_port_name[WWN_SIZE]; |
| uint16_t boot_lun_number; |
| uint16_t reserved_8; |
| |
| uint8_t alt1_boot_port_name[WWN_SIZE]; |
| uint16_t alt1_boot_lun_number; |
| uint16_t reserved_9; |
| |
| uint8_t alt2_boot_port_name[WWN_SIZE]; |
| uint16_t alt2_boot_lun_number; |
| uint16_t reserved_10; |
| |
| uint8_t alt3_boot_port_name[WWN_SIZE]; |
| uint16_t alt3_boot_lun_number; |
| uint16_t reserved_11; |
| |
| /* |
| * BIT 0 = Selective Login |
| * BIT 1 = Alt-Boot Enable |
| * BIT 2 = Reserved |
| * BIT 3 = Boot Order List |
| * BIT 4 = Reserved |
| * BIT 5 = Selective LUN |
| * BIT 6 = Reserved |
| * BIT 7-31 = |
| */ |
| uint32_t efi_parameters; |
| |
| uint8_t reset_delay; |
| uint8_t reserved_12; |
| uint16_t reserved_13; |
| |
| uint16_t boot_id_number; |
| uint16_t reserved_14; |
| |
| uint16_t max_luns_per_target; |
| uint16_t reserved_15; |
| |
| uint16_t port_down_retry_count; |
| uint16_t link_down_timeout; |
| |
| /* FCode parameters. */ |
| uint16_t fcode_parameter; |
| |
| uint16_t reserved_16[3]; |
| |
| /* Offset 352. */ |
| uint8_t prev_drv_ver_major; |
| uint8_t prev_drv_ver_submajob; |
| uint8_t prev_drv_ver_minor; |
| uint8_t prev_drv_ver_subminor; |
| |
| uint16_t prev_bios_ver_major; |
| uint16_t prev_bios_ver_minor; |
| |
| uint16_t prev_efi_ver_major; |
| uint16_t prev_efi_ver_minor; |
| |
| uint16_t prev_fw_ver_major; |
| uint8_t prev_fw_ver_minor; |
| uint8_t prev_fw_ver_subminor; |
| |
| uint16_t reserved_17[8]; |
| |
| /* Offset 384. */ |
| uint16_t reserved_18[16]; |
| |
| /* Offset 416. */ |
| uint16_t reserved_19[16]; |
| |
| /* Offset 448. */ |
| uint16_t reserved_20[16]; |
| |
| /* Offset 480. */ |
| uint8_t model_name[16]; |
| |
| uint16_t reserved_21[2]; |
| |
| /* Offset 500. */ |
| /* HW Parameter Block. */ |
| uint16_t pcie_table_sig; |
| uint16_t pcie_table_offset; |
| |
| uint16_t subsystem_vendor_id; |
| uint16_t subsystem_device_id; |
| |
| uint32_t checksum; |
| }; |
| |
| /* |
| * ISP Initialization Control Block. |
| * Little endian except where noted. |
| */ |
| #define ICB_VERSION 1 |
| struct init_cb_24xx { |
| uint16_t version; |
| uint16_t reserved_1; |
| |
| uint16_t frame_payload_size; |
| uint16_t execution_throttle; |
| uint16_t exchange_count; |
| |
| uint16_t hard_address; |
| |
| uint8_t port_name[WWN_SIZE]; /* Big endian. */ |
| uint8_t node_name[WWN_SIZE]; /* Big endian. */ |
| |
| uint16_t response_q_inpointer; |
| uint16_t request_q_outpointer; |
| |
| uint16_t login_retry_count; |
| |
| uint16_t prio_request_q_outpointer; |
| |
| uint16_t response_q_length; |
| uint16_t request_q_length; |
| |
| uint16_t link_down_on_nos; /* Milliseconds. */ |
| |
| uint16_t prio_request_q_length; |
| |
| uint32_t request_q_address[2]; |
| uint32_t response_q_address[2]; |
| uint32_t prio_request_q_address[2]; |
| |
| uint16_t msix; |
| uint16_t msix_atio; |
| uint8_t reserved_2[4]; |
| |
| uint16_t atio_q_inpointer; |
| uint16_t atio_q_length; |
| uint32_t atio_q_address[2]; |
| |
| uint16_t interrupt_delay_timer; /* 100us increments. */ |
| uint16_t login_timeout; |
| |
| /* |
| * BIT 0 = Enable Hard Loop Id |
| * BIT 1 = Enable Fairness |
| * BIT 2 = Enable Full-Duplex |
| * BIT 3 = Reserved |
| * BIT 4 = Enable Target Mode |
| * BIT 5 = Disable Initiator Mode |
| * BIT 6 = Acquire FA-WWN |
| * BIT 7 = Enable D-port Diagnostics |
| * |
| * BIT 8 = Reserved |
| * BIT 9 = Non Participating LIP |
| * BIT 10 = Descending Loop ID Search |
| * BIT 11 = Acquire Loop ID in LIPA |
| * BIT 12 = Reserved |
| * BIT 13 = Full Login after LIP |
| * BIT 14 = Node Name Option |
| * BIT 15-31 = Reserved |
| */ |
| uint32_t firmware_options_1; |
| |
| /* |
| * BIT 0 = Operation Mode bit 0 |
| * BIT 1 = Operation Mode bit 1 |
| * BIT 2 = Operation Mode bit 2 |
| * BIT 3 = Operation Mode bit 3 |
| * BIT 4 = Connection Options bit 0 |
| * BIT 5 = Connection Options bit 1 |
| * BIT 6 = Connection Options bit 2 |
| * BIT 7 = Enable Non part on LIHA failure |
| * |
| * BIT 8 = Enable Class 2 |
| * BIT 9 = Enable ACK0 |
| * BIT 10 = Reserved |
| * BIT 11 = Enable FC-SP Security |
| * BIT 12 = FC Tape Enable |
| * BIT 13 = Reserved |
| * BIT 14 = Enable Target PRLI Control |
| * BIT 15-31 = Reserved |
| */ |
| uint32_t firmware_options_2; |
| |
| /* |
| * BIT 0 = Reserved |
| * BIT 1 = Soft ID only |
| * BIT 2 = Reserved |
| * BIT 3 = Reserved |
| * BIT 4 = FCP RSP Payload bit 0 |
| * BIT 5 = FCP RSP Payload bit 1 |
| * BIT 6 = Enable Receive Out-of-Order data frame handling |
| * BIT 7 = Disable Automatic PLOGI on Local Loop |
| * |
| * BIT 8 = Reserved |
| * BIT 9 = Enable Out-of-Order FCP_XFER_RDY relative offset handling |
| * BIT 10 = Reserved |
| * BIT 11 = Reserved |
| * BIT 12 = Reserved |
| * BIT 13 = Data Rate bit 0 |
| * BIT 14 = Data Rate bit 1 |
| * BIT 15 = Data Rate bit 2 |
| * BIT 16 = Enable 75 ohm Termination Select |
| * BIT 17-28 = Reserved |
| * BIT 29 = Enable response queue 0 in index shadowing |
| * BIT 30 = Enable request queue 0 out index shadowing |
| * BIT 31 = Reserved |
| */ |
| uint32_t firmware_options_3; |
| uint16_t qos; |
| uint16_t rid; |
| uint8_t reserved_3[20]; |
| }; |
| |
| /* |
| * ISP queue - command entry structure definition. |
| */ |
| #define COMMAND_BIDIRECTIONAL 0x75 |
| struct cmd_bidir { |
| uint8_t entry_type; /* Entry type. */ |
| uint8_t entry_count; /* Entry count. */ |
| uint8_t sys_define; /* System defined */ |
| uint8_t entry_status; /* Entry status. */ |
| |
| uint32_t handle; /* System handle. */ |
| |
| uint16_t nport_handle; /* N_PORT hanlde. */ |
| |
| uint16_t timeout; /* Commnad timeout. */ |
| |
| uint16_t wr_dseg_count; /* Write Data segment count. */ |
| uint16_t rd_dseg_count; /* Read Data segment count. */ |
| |
| struct scsi_lun lun; /* FCP LUN (BE). */ |
| |
| uint16_t control_flags; /* Control flags. */ |
| #define BD_WRAP_BACK BIT_3 |
| #define BD_READ_DATA BIT_1 |
| #define BD_WRITE_DATA BIT_0 |
| |
| uint16_t fcp_cmnd_dseg_len; /* Data segment length. */ |
| uint32_t fcp_cmnd_dseg_address[2]; /* Data segment address. */ |
| |
| uint16_t reserved[2]; /* Reserved */ |
| |
| uint32_t rd_byte_count; /* Total Byte count Read. */ |
| uint32_t wr_byte_count; /* Total Byte count write. */ |
| |
| uint8_t port_id[3]; /* PortID of destination port.*/ |
| uint8_t vp_index; |
| |
| uint32_t fcp_data_dseg_address[2]; /* Data segment address. */ |
| uint16_t fcp_data_dseg_len; /* Data segment length. */ |
| }; |
| |
| #define COMMAND_TYPE_6 0x48 /* Command Type 6 entry */ |
| struct cmd_type_6 { |
| uint8_t entry_type; /* Entry type. */ |
| uint8_t entry_count; /* Entry count. */ |
| uint8_t sys_define; /* System defined. */ |
| uint8_t entry_status; /* Entry Status. */ |
| |
| uint32_t handle; /* System handle. */ |
| |
| uint16_t nport_handle; /* N_PORT handle. */ |
| uint16_t timeout; /* Command timeout. */ |
| |
| uint16_t dseg_count; /* Data segment count. */ |
| |
| uint16_t fcp_rsp_dsd_len; /* FCP_RSP DSD length. */ |
| |
| struct scsi_lun lun; /* FCP LUN (BE). */ |
| |
| uint16_t control_flags; /* Control flags. */ |
| #define CF_DIF_SEG_DESCR_ENABLE BIT_3 |
| #define CF_DATA_SEG_DESCR_ENABLE BIT_2 |
| #define CF_READ_DATA BIT_1 |
| #define CF_WRITE_DATA BIT_0 |
| |
| uint16_t fcp_cmnd_dseg_len; /* Data segment length. */ |
| uint32_t fcp_cmnd_dseg_address[2]; /* Data segment address. */ |
| |
| uint32_t fcp_rsp_dseg_address[2]; /* Data segment address. */ |
| |
| uint32_t byte_count; /* Total byte count. */ |
| |
| uint8_t port_id[3]; /* PortID of destination port. */ |
| uint8_t vp_index; |
| |
| uint32_t fcp_data_dseg_address[2]; /* Data segment address. */ |
| uint32_t fcp_data_dseg_len; /* Data segment length. */ |
| }; |
| |
| #define COMMAND_TYPE_7 0x18 /* Command Type 7 entry */ |
| struct cmd_type_7 { |
| uint8_t entry_type; /* Entry type. */ |
| uint8_t entry_count; /* Entry count. */ |
| uint8_t sys_define; /* System defined. */ |
| uint8_t entry_status; /* Entry Status. */ |
| |
| uint32_t handle; /* System handle. */ |
| |
| uint16_t nport_handle; /* N_PORT handle. */ |
| uint16_t timeout; /* Command timeout. */ |
| #define FW_MAX_TIMEOUT 0x1999 |
| |
| uint16_t dseg_count; /* Data segment count. */ |
| uint16_t reserved_1; |
| |
| struct scsi_lun lun; /* FCP LUN (BE). */ |
| |
| uint16_t task_mgmt_flags; /* Task management flags. */ |
| #define TMF_CLEAR_ACA BIT_14 |
| #define TMF_TARGET_RESET BIT_13 |
| #define TMF_LUN_RESET BIT_12 |
| #define TMF_CLEAR_TASK_SET BIT_10 |
| #define TMF_ABORT_TASK_SET BIT_9 |
| #define TMF_DSD_LIST_ENABLE BIT_2 |
| #define TMF_READ_DATA BIT_1 |
| #define TMF_WRITE_DATA BIT_0 |
| |
| uint8_t task; |
| #define TSK_SIMPLE 0 |
| #define TSK_HEAD_OF_QUEUE 1 |
| #define TSK_ORDERED 2 |
| #define TSK_ACA 4 |
| #define TSK_UNTAGGED 5 |
| |
| uint8_t crn; |
| |
| uint8_t fcp_cdb[MAX_CMDSZ]; /* SCSI command words. */ |
| uint32_t byte_count; /* Total byte count. */ |
| |
| uint8_t port_id[3]; /* PortID of destination port. */ |
| uint8_t vp_index; |
| |
| uint32_t dseg_0_address[2]; /* Data segment 0 address. */ |
| uint32_t dseg_0_len; /* Data segment 0 length. */ |
| }; |
| |
| #define COMMAND_TYPE_CRC_2 0x6A /* Command Type CRC_2 (Type 6) |
| * (T10-DIF) */ |
| struct cmd_type_crc_2 { |
| uint8_t entry_type; /* Entry type. */ |
| uint8_t entry_count; /* Entry count. */ |
| uint8_t sys_define; /* System defined. */ |
| uint8_t entry_status; /* Entry Status. */ |
| |
| uint32_t handle; /* System handle. */ |
| |
| uint16_t nport_handle; /* N_PORT handle. */ |
| uint16_t timeout; /* Command timeout. */ |
| |
| uint16_t dseg_count; /* Data segment count. */ |
| |
| uint16_t fcp_rsp_dseg_len; /* FCP_RSP DSD length. */ |
| |
| struct scsi_lun lun; /* FCP LUN (BE). */ |
| |
| uint16_t control_flags; /* Control flags. */ |
| |
| uint16_t fcp_cmnd_dseg_len; /* Data segment length. */ |
| uint32_t fcp_cmnd_dseg_address[2]; /* Data segment address. */ |
| |
| uint32_t fcp_rsp_dseg_address[2]; /* Data segment address. */ |
| |
| uint32_t byte_count; /* Total byte count. */ |
| |
| uint8_t port_id[3]; /* PortID of destination port. */ |
| uint8_t vp_index; |
| |
| uint32_t crc_context_address[2]; /* Data segment address. */ |
| uint16_t crc_context_len; /* Data segment length. */ |
| uint16_t reserved_1; /* MUST be set to 0. */ |
| }; |
| |
| |
| /* |
| * ISP queue - status entry structure definition. |
| */ |
| #define STATUS_TYPE 0x03 /* Status entry. */ |
| struct sts_entry_24xx { |
| uint8_t entry_type; /* Entry type. */ |
| uint8_t entry_count; /* Entry count. */ |
| uint8_t sys_define; /* System defined. */ |
| uint8_t entry_status; /* Entry Status. */ |
| |
| uint32_t handle; /* System handle. */ |
| |
| uint16_t comp_status; /* Completion status. */ |
| uint16_t ox_id; /* OX_ID used by the firmware. */ |
| |
| uint32_t residual_len; /* FW calc residual transfer length. */ |
| |
| union { |
| uint16_t reserved_1; |
| uint16_t nvme_rsp_pyld_len; |
| }; |
| |
| uint16_t state_flags; /* State flags. */ |
| #define SF_TRANSFERRED_DATA BIT_11 |
| #define SF_NVME_ERSP BIT_6 |
| #define SF_FCP_RSP_DMA BIT_0 |
| |
| uint16_t retry_delay; |
| uint16_t scsi_status; /* SCSI status. */ |
| #define SS_CONFIRMATION_REQ BIT_12 |
| |
| uint32_t rsp_residual_count; /* FCP RSP residual count. */ |
| |
| uint32_t sense_len; /* FCP SENSE length. */ |
| |
| union { |
| struct { |
| uint32_t rsp_data_len; /* FCP response data length */ |
| uint8_t data[28]; /* FCP rsp/sense information */ |
| }; |
| struct nvme_fc_ersp_iu nvme_ersp; |
| uint8_t nvme_ersp_data[32]; |
| }; |
| |
| /* |
| * If DIF Error is set in comp_status, these additional fields are |
| * defined: |
| * |
| * !!! NOTE: Firmware sends expected/actual DIF data in big endian |
| * format; but all of the "data" field gets swab32-d in the beginning |
| * of qla2x00_status_entry(). |
| * |
| * &data[10] : uint8_t report_runt_bg[2]; - computed guard |
| * &data[12] : uint8_t actual_dif[8]; - DIF Data received |
| * &data[20] : uint8_t expected_dif[8]; - DIF Data computed |
| */ |
| }; |
| |
| |
| /* |
| * Status entry completion status |
| */ |
| #define CS_DATA_REASSEMBLY_ERROR 0x11 /* Data Reassembly Error.. */ |
| #define CS_ABTS_BY_TARGET 0x13 /* Target send ABTS to abort IOCB. */ |
| #define CS_FW_RESOURCE 0x2C /* Firmware Resource Unavailable. */ |
| #define CS_TASK_MGMT_OVERRUN 0x30 /* Task management overrun (8+). */ |
| #define CS_ABORT_BY_TARGET 0x47 /* Abort By Target. */ |
| |
| /* |
| * ISP queue - marker entry structure definition. |
| */ |
| #define MARKER_TYPE 0x04 /* Marker entry. */ |
| struct mrk_entry_24xx { |
| uint8_t entry_type; /* Entry type. */ |
| uint8_t entry_count; /* Entry count. */ |
| uint8_t handle_count; /* Handle count. */ |
| uint8_t entry_status; /* Entry Status. */ |
| |
| uint32_t handle; /* System handle. */ |
| |
| uint16_t nport_handle; /* N_PORT handle. */ |
| |
| uint8_t modifier; /* Modifier (7-0). */ |
| #define MK_SYNC_ID_LUN 0 /* Synchronize ID/LUN */ |
| #define MK_SYNC_ID 1 /* Synchronize ID */ |
| #define MK_SYNC_ALL 2 /* Synchronize all ID/LUN */ |
| uint8_t reserved_1; |
| |
| uint8_t reserved_2; |
| uint8_t vp_index; |
| |
| uint16_t reserved_3; |
| |
| uint8_t lun[8]; /* FCP LUN (BE). */ |
| uint8_t reserved_4[40]; |
| }; |
| |
| /* |
| * ISP queue - CT Pass-Through entry structure definition. |
| */ |
| #define CT_IOCB_TYPE 0x29 /* CT Pass-Through IOCB entry */ |
| struct ct_entry_24xx { |
| uint8_t entry_type; /* Entry type. */ |
| uint8_t entry_count; /* Entry count. */ |
| uint8_t sys_define; /* System Defined. */ |
| uint8_t entry_status; /* Entry Status. */ |
| |
| uint32_t handle; /* System handle. */ |
| |
| uint16_t comp_status; /* Completion status. */ |
| |
| uint16_t nport_handle; /* N_PORT handle. */ |
| |
| uint16_t cmd_dsd_count; |
| |
| uint8_t vp_index; |
| uint8_t reserved_1; |
| |
| uint16_t timeout; /* Command timeout. */ |
| uint16_t reserved_2; |
| |
| uint16_t rsp_dsd_count; |
| |
| uint8_t reserved_3[10]; |
| |
| uint32_t rsp_byte_count; |
| uint32_t cmd_byte_count; |
| |
| uint32_t dseg_0_address[2]; /* Data segment 0 address. */ |
| uint32_t dseg_0_len; /* Data segment 0 length. */ |
| uint32_t dseg_1_address[2]; /* Data segment 1 address. */ |
| uint32_t dseg_1_len; /* Data segment 1 length. */ |
| }; |
| |
| /* |
| * ISP queue - ELS Pass-Through entry structure definition. |
| */ |
| #define ELS_IOCB_TYPE 0x53 /* ELS Pass-Through IOCB entry */ |
| struct els_entry_24xx { |
| uint8_t entry_type; /* Entry type. */ |
| uint8_t entry_count; /* Entry count. */ |
| uint8_t sys_define; /* System Defined. */ |
| uint8_t entry_status; /* Entry Status. */ |
| |
| uint32_t handle; /* System handle. */ |
| |
| uint16_t reserved_1; |
| |
| uint16_t nport_handle; /* N_PORT handle. */ |
| |
| uint16_t tx_dsd_count; |
| |
| uint8_t vp_index; |
| uint8_t sof_type; |
| #define EST_SOFI3 (1 << 4) |
| #define EST_SOFI2 (3 << 4) |
| |
| uint32_t rx_xchg_address; /* Receive exchange address. */ |
| uint16_t rx_dsd_count; |
| |
| uint8_t opcode; |
| uint8_t reserved_2; |
| |
| uint8_t port_id[3]; |
| uint8_t reserved_3; |
| |
| uint16_t reserved_4; |
| |
| uint16_t control_flags; /* Control flags. */ |
| #define ECF_PAYLOAD_DESCR_MASK (BIT_15|BIT_14|BIT_13) |
| #define EPD_ELS_COMMAND (0 << 13) |
| #define EPD_ELS_ACC (1 << 13) |
| #define EPD_ELS_RJT (2 << 13) |
| #define EPD_RX_XCHG (3 << 13) |
| #define ECF_CLR_PASSTHRU_PEND BIT_12 |
| #define ECF_INCL_FRAME_HDR BIT_11 |
| |
| uint32_t rx_byte_count; |
| uint32_t tx_byte_count; |
| |
| uint32_t tx_address[2]; /* Data segment 0 address. */ |
| uint32_t tx_len; /* Data segment 0 length. */ |
| uint32_t rx_address[2]; /* Data segment 1 address. */ |
| uint32_t rx_len; /* Data segment 1 length. */ |
| }; |
| |
| struct els_sts_entry_24xx { |
| uint8_t entry_type; /* Entry type. */ |
| uint8_t entry_count; /* Entry count. */ |
| uint8_t sys_define; /* System Defined. */ |
| uint8_t entry_status; /* Entry Status. */ |
| |
| uint32_t handle; /* System handle. */ |
| |
| uint16_t comp_status; |
| |
| uint16_t nport_handle; /* N_PORT handle. */ |
| |
| uint16_t reserved_1; |
| |
| uint8_t vp_index; |
| uint8_t sof_type; |
| |
| uint32_t rx_xchg_address; /* Receive exchange address. */ |
| uint16_t reserved_2; |
| |
| uint8_t opcode; |
| uint8_t reserved_3; |
| |
| uint8_t port_id[3]; |
| uint8_t reserved_4; |
| |
| uint16_t reserved_5; |
| |
| uint16_t control_flags; /* Control flags. */ |
| uint32_t total_byte_count; |
| uint32_t error_subcode_1; |
| uint32_t error_subcode_2; |
| }; |
| /* |
| * ISP queue - Mailbox Command entry structure definition. |
| */ |
| #define MBX_IOCB_TYPE 0x39 |
| struct mbx_entry_24xx { |
| uint8_t entry_type; /* Entry type. */ |
| uint8_t entry_count; /* Entry count. */ |
| uint8_t handle_count; /* Handle count. */ |
| uint8_t entry_status; /* Entry Status. */ |
| |
| uint32_t handle; /* System handle. */ |
| |
| uint16_t mbx[28]; |
| }; |
| |
| |
| #define LOGINOUT_PORT_IOCB_TYPE 0x52 /* Login/Logout Port entry. */ |
| struct logio_entry_24xx { |
| uint8_t entry_type; /* Entry type. */ |
| uint8_t entry_count; /* Entry count. */ |
| uint8_t sys_define; /* System defined. */ |
| uint8_t entry_status; /* Entry Status. */ |
| |
| uint32_t handle; /* System handle. */ |
| |
| uint16_t comp_status; /* Completion status. */ |
| #define CS_LOGIO_ERROR 0x31 /* Login/Logout IOCB error. */ |
| |
| uint16_t nport_handle; /* N_PORT handle. */ |
| |
| uint16_t control_flags; /* Control flags. */ |
| /* Modifiers. */ |
| #define LCF_INCLUDE_SNS BIT_10 /* Include SNS (FFFFFC) during LOGO. */ |
| #define LCF_FCP2_OVERRIDE BIT_9 /* Set/Reset word 3 of PRLI. */ |
| #define LCF_CLASS_2 BIT_8 /* Enable class 2 during PLOGI. */ |
| #define LCF_FREE_NPORT BIT_7 /* Release NPORT handle after LOGO. */ |
| #define LCF_EXPL_LOGO BIT_6 /* Perform an explicit LOGO. */ |
| #define LCF_NVME_PRLI BIT_6 /* Perform NVME FC4 PRLI */ |
| #define LCF_SKIP_PRLI BIT_5 /* Skip PRLI after PLOGI. */ |
| #define LCF_IMPL_LOGO_ALL BIT_5 /* Implicit LOGO to all ports. */ |
| #define LCF_COND_PLOGI BIT_4 /* PLOGI only if not logged-in. */ |
| #define LCF_IMPL_LOGO BIT_4 /* Perform an implicit LOGO. */ |
| #define LCF_IMPL_PRLO BIT_4 /* Perform an implicit PRLO. */ |
| /* Commands. */ |
| #define LCF_COMMAND_PLOGI 0x00 /* PLOGI. */ |
| #define LCF_COMMAND_PRLI 0x01 /* PRLI. */ |
| #define LCF_COMMAND_PDISC 0x02 /* PDISC. */ |
| #define LCF_COMMAND_ADISC 0x03 /* ADISC. */ |
| #define LCF_COMMAND_LOGO 0x08 /* LOGO. */ |
| #define LCF_COMMAND_PRLO 0x09 /* PRLO. */ |
| #define LCF_COMMAND_TPRLO 0x0A /* TPRLO. */ |
| |
| uint8_t vp_index; |
| uint8_t reserved_1; |
| |
| uint8_t port_id[3]; /* PortID of destination port. */ |
| |
| uint8_t rsp_size; /* Response size in 32bit words. */ |
| |
| uint32_t io_parameter[11]; /* General I/O parameters. */ |
| #define LSC_SCODE_NOLINK 0x01 |
| #define LSC_SCODE_NOIOCB 0x02 |
| #define LSC_SCODE_NOXCB 0x03 |
| #define LSC_SCODE_CMD_FAILED 0x04 |
| #define LSC_SCODE_NOFABRIC 0x05 |
| #define LSC_SCODE_FW_NOT_READY 0x07 |
| #define LSC_SCODE_NOT_LOGGED_IN 0x09 |
| #define LSC_SCODE_NOPCB 0x0A |
| |
| #define LSC_SCODE_ELS_REJECT 0x18 |
| #define LSC_SCODE_CMD_PARAM_ERR 0x19 |
| #define LSC_SCODE_PORTID_USED 0x1A |
| #define LSC_SCODE_NPORT_USED 0x1B |
| #define LSC_SCODE_NONPORT 0x1C |
| #define LSC_SCODE_LOGGED_IN 0x1D |
| #define LSC_SCODE_NOFLOGI_ACC 0x1F |
| }; |
| |
| #define TSK_MGMT_IOCB_TYPE 0x14 |
| struct tsk_mgmt_entry { |
| uint8_t entry_type; /* Entry type. */ |
| uint8_t entry_count; /* Entry count. */ |
| uint8_t handle_count; /* Handle count. */ |
| uint8_t entry_status; /* Entry Status. */ |
| |
| uint32_t handle; /* System handle. */ |
| |
| uint16_t nport_handle; /* N_PORT handle. */ |
| |
| uint16_t reserved_1; |
| |
| uint16_t delay; /* Activity delay in seconds. */ |
| |
| uint16_t timeout; /* Command timeout. */ |
| |
| struct scsi_lun lun; /* FCP LUN (BE). */ |
| |
| uint32_t control_flags; /* Control Flags. */ |
| #define TCF_NOTMCMD_TO_TARGET BIT_31 |
| #define TCF_LUN_RESET BIT_4 |
| #define TCF_ABORT_TASK_SET BIT_3 |
| #define TCF_CLEAR_TASK_SET BIT_2 |
| #define TCF_TARGET_RESET BIT_1 |
| #define TCF_CLEAR_ACA BIT_0 |
| |
| uint8_t reserved_2[20]; |
| |
| uint8_t port_id[3]; /* PortID of destination port. */ |
| uint8_t vp_index; |
| |
| uint8_t reserved_3[12]; |
| }; |
| |
| #define ABORT_IOCB_TYPE 0x33 |
| struct abort_entry_24xx { |
| uint8_t entry_type; /* Entry type. */ |
| uint8_t entry_count; /* Entry count. */ |
| uint8_t handle_count; /* Handle count. */ |
| uint8_t entry_status; /* Entry Status. */ |
| |
| uint32_t handle; /* System handle. */ |
| |
| uint16_t nport_handle; /* N_PORT handle. */ |
| /* or Completion status. */ |
| |
| uint16_t options; /* Options. */ |
| #define AOF_NO_ABTS BIT_0 /* Do not send any ABTS. */ |
| |
| uint32_t handle_to_abort; /* System handle to abort. */ |
| |
| uint16_t req_que_no; |
| uint8_t reserved_1[30]; |
| |
| uint8_t port_id[3]; /* PortID of destination port. */ |
| uint8_t vp_index; |
| |
| uint8_t reserved_2[12]; |
| }; |
| |
| /* |
| * ISP I/O Register Set structure definitions. |
| */ |
| struct device_reg_24xx { |
| uint32_t flash_addr; /* Flash/NVRAM BIOS address. */ |
| #define FARX_DATA_FLAG BIT_31 |
| #define FARX_ACCESS_FLASH_CONF 0x7FFD0000 |
| #define FARX_ACCESS_FLASH_DATA 0x7FF00000 |
| #define FARX_ACCESS_NVRAM_CONF 0x7FFF0000 |
| #define FARX_ACCESS_NVRAM_DATA 0x7FFE0000 |
| |
| #define FA_NVRAM_FUNC0_ADDR 0x80 |
| #define FA_NVRAM_FUNC1_ADDR 0x180 |
| |
| #define FA_NVRAM_VPD_SIZE 0x200 |
| #define FA_NVRAM_VPD0_ADDR 0x00 |
| #define FA_NVRAM_VPD1_ADDR 0x100 |
| |
| #define FA_BOOT_CODE_ADDR 0x00000 |
| /* |
| * RISC code begins at offset 512KB |
| * within flash. Consisting of two |
| * contiguous RISC code segments. |
| */ |
| #define FA_RISC_CODE_ADDR 0x20000 |
| #define FA_RISC_CODE_SEGMENTS 2 |
| |
| #define FA_FLASH_DESCR_ADDR_24 0x11000 |
| #define FA_FLASH_LAYOUT_ADDR_24 0x11400 |
| #define FA_NPIV_CONF0_ADDR_24 0x16000 |
| #define FA_NPIV_CONF1_ADDR_24 0x17000 |
| |
| #define FA_FW_AREA_ADDR 0x40000 |
| #define FA_VPD_NVRAM_ADDR 0x48000 |
| #define FA_FEATURE_ADDR 0x4C000 |
| #define FA_FLASH_DESCR_ADDR 0x50000 |
| #define FA_FLASH_LAYOUT_ADDR 0x50400 |
| #define FA_HW_EVENT0_ADDR 0x54000 |
| #define FA_HW_EVENT1_ADDR 0x54400 |
| #define FA_HW_EVENT_SIZE 0x200 |
| #define FA_HW_EVENT_ENTRY_SIZE 4 |
| #define FA_NPIV_CONF0_ADDR 0x5C000 |
| #define FA_NPIV_CONF1_ADDR 0x5D000 |
| #define FA_FCP_PRIO0_ADDR 0x10000 |
| #define FA_FCP_PRIO1_ADDR 0x12000 |
| |
| /* |
| * Flash Error Log Event Codes. |
| */ |
| #define HW_EVENT_RESET_ERR 0xF00B |
| #define HW_EVENT_ISP_ERR 0xF020 |
| #define HW_EVENT_PARITY_ERR 0xF022 |
| #define HW_EVENT_NVRAM_CHKSUM_ERR 0xF023 |
| #define HW_EVENT_FLASH_FW_ERR 0xF024 |
| |
| uint32_t flash_data; /* Flash/NVRAM BIOS data. */ |
| |
| uint32_t ctrl_status; /* Control/Status. */ |
| #define CSRX_FLASH_ACCESS_ERROR BIT_18 /* Flash/NVRAM Access Error. */ |
| #define CSRX_DMA_ACTIVE BIT_17 /* DMA Active status. */ |
| #define CSRX_DMA_SHUTDOWN BIT_16 /* DMA Shutdown control status. */ |
| #define CSRX_FUNCTION BIT_15 /* Function number. */ |
| /* PCI-X Bus Mode. */ |
| #define CSRX_PCIX_BUS_MODE_MASK (BIT_11|BIT_10|BIT_9|BIT_8) |
| #define PBM_PCI_33MHZ (0 << 8) |
| #define PBM_PCIX_M1_66MHZ (1 << 8) |
| #define PBM_PCIX_M1_100MHZ (2 << 8) |
| #define PBM_PCIX_M1_133MHZ (3 << 8) |
| #define PBM_PCIX_M2_66MHZ (5 << 8) |
| #define PBM_PCIX_M2_100MHZ (6 << 8) |
| #define PBM_PCIX_M2_133MHZ (7 << 8) |
| #define PBM_PCI_66MHZ (8 << 8) |
| /* Max Write Burst byte count. */ |
| #define CSRX_MAX_WRT_BURST_MASK (BIT_5|BIT_4) |
| #define MWB_512_BYTES (0 << 4) |
| #define MWB_1024_BYTES (1 << 4) |
| #define MWB_2048_BYTES (2 << 4) |
| #define MWB_4096_BYTES (3 << 4) |
| |
| #define CSRX_64BIT_SLOT BIT_2 /* PCI 64-Bit Bus Slot. */ |
| #define CSRX_FLASH_ENABLE BIT_1 /* Flash BIOS Read/Write enable. */ |
| #define CSRX_ISP_SOFT_RESET BIT_0 /* ISP soft reset. */ |
| |
| uint32_t ictrl; /* Interrupt control. */ |
| #define ICRX_EN_RISC_INT BIT_3 /* Enable RISC interrupts on PCI. */ |
| |
| uint32_t istatus; /* Interrupt status. */ |
| #define ISRX_RISC_INT BIT_3 /* RISC interrupt. */ |
| |
| uint32_t unused_1[2]; /* Gap. */ |
| |
| /* Request Queue. */ |
| uint32_t req_q_in; /* In-Pointer. */ |
| uint32_t req_q_out; /* Out-Pointer. */ |
| /* Response Queue. */ |
| uint32_t rsp_q_in; /* In-Pointer. */ |
| uint32_t rsp_q_out; /* Out-Pointer. */ |
| /* Priority Request Queue. */ |
| uint32_t preq_q_in; /* In-Pointer. */ |
| uint32_t preq_q_out; /* Out-Pointer. */ |
| |
| uint32_t unused_2[2]; /* Gap. */ |
| |
| /* ATIO Queue. */ |
| uint32_t atio_q_in; /* In-Pointer. */ |
| uint32_t atio_q_out; /* Out-Pointer. */ |
| |
| uint32_t host_status; |
| #define HSRX_RISC_INT BIT_15 /* RISC to Host interrupt. */ |
| #define HSRX_RISC_PAUSED BIT_8 /* RISC Paused. */ |
| |
| uint32_t hccr; /* Host command & control register. */ |
| /* HCCR statuses. */ |
| #define HCCRX_HOST_INT BIT_6 /* Host to RISC interrupt bit. */ |
| #define HCCRX_RISC_RESET BIT_5 /* RISC Reset mode bit. */ |
| /* HCCR commands. */ |
| /* NOOP. */ |
| #define HCCRX_NOOP 0x00000000 |
| /* Set RISC Reset. */ |
| #define HCCRX_SET_RISC_RESET 0x10000000 |
| /* Clear RISC Reset. */ |
| #define HCCRX_CLR_RISC_RESET 0x20000000 |
| /* Set RISC Pause. */ |
| #define HCCRX_SET_RISC_PAUSE 0x30000000 |
| /* Releases RISC Pause. */ |
| #define HCCRX_REL_RISC_PAUSE 0x40000000 |
| /* Set HOST to RISC interrupt. */ |
| #define HCCRX_SET_HOST_INT 0x50000000 |
| /* Clear HOST to RISC interrupt. */ |
| #define HCCRX_CLR_HOST_INT 0x60000000 |
| /* Clear RISC to PCI interrupt. */ |
| #define HCCRX_CLR_RISC_INT 0xA0000000 |
| |
| uint32_t gpiod; /* GPIO Data register. */ |
| |
| /* LED update mask. */ |
| #define GPDX_LED_UPDATE_MASK (BIT_20|BIT_19|BIT_18) |
| /* Data update mask. */ |
| #define GPDX_DATA_UPDATE_MASK (BIT_17|BIT_16) |
| /* Data update mask. */ |
| #define GPDX_DATA_UPDATE_2_MASK (BIT_28|BIT_27|BIT_26|BIT_17|BIT_16) |
| /* LED control mask. */ |
| #define GPDX_LED_COLOR_MASK (BIT_4|BIT_3|BIT_2) |
| /* LED bit values. Color names as |
| * referenced in fw spec. |
| */ |
| #define GPDX_LED_YELLOW_ON BIT_2 |
| #define GPDX_LED_GREEN_ON BIT_3 |
| #define GPDX_LED_AMBER_ON BIT_4 |
| /* Data in/out. */ |
| #define GPDX_DATA_INOUT (BIT_1|BIT_0) |
| |
| uint32_t gpioe; /* GPIO Enable register. */ |
| /* Enable update mask. */ |
| #define GPEX_ENABLE_UPDATE_MASK (BIT_17|BIT_16) |
| /* Enable update mask. */ |
| #define GPEX_ENABLE_UPDATE_2_MASK (BIT_28|BIT_27|BIT_26|BIT_17|BIT_16) |
| /* Enable. */ |
| #define GPEX_ENABLE (BIT_1|BIT_0) |
| |
| uint32_t iobase_addr; /* I/O Bus Base Address register. */ |
| |
| uint32_t unused_3[10]; /* Gap. */ |
| |
| uint16_t mailbox0; |
| uint16_t mailbox1; |
| uint16_t mailbox2; |
| uint16_t mailbox3; |
| uint16_t mailbox4; |
| uint16_t mailbox5; |
| uint16_t mailbox6; |
| uint16_t mailbox7; |
| uint16_t mailbox8; |
| uint16_t mailbox9; |
| uint16_t mailbox10; |
| uint16_t mailbox11; |
| uint16_t mailbox12; |
| uint16_t mailbox13; |
| uint16_t mailbox14; |
| uint16_t mailbox15; |
| uint16_t mailbox16; |
| uint16_t mailbox17; |
| uint16_t mailbox18; |
| uint16_t mailbox19; |
| uint16_t mailbox20; |
| uint16_t mailbox21; |
| uint16_t mailbox22; |
| uint16_t mailbox23; |
| uint16_t mailbox24; |
| uint16_t mailbox25; |
| uint16_t mailbox26; |
| uint16_t mailbox27; |
| uint16_t mailbox28; |
| uint16_t mailbox29; |
| uint16_t mailbox30; |
| uint16_t mailbox31; |
| |
| uint32_t iobase_window; |
| uint32_t iobase_c4; |
| uint32_t iobase_c8; |
| uint32_t unused_4_1[6]; /* Gap. */ |
| uint32_t iobase_q; |
| uint32_t unused_5[2]; /* Gap. */ |
| uint32_t iobase_select; |
| uint32_t unused_6[2]; /* Gap. */ |
| uint32_t iobase_sdata; |
| }; |
| /* RISC-RISC semaphore register PCI offet */ |
| #define RISC_REGISTER_BASE_OFFSET 0x7010 |
| #define RISC_REGISTER_WINDOW_OFFET 0x6 |
| |
| /* RISC-RISC semaphore/flag register (risc address 0x7016) */ |
| |
| #define RISC_SEMAPHORE 0x1UL |
| #define RISC_SEMAPHORE_WE (RISC_SEMAPHORE << 16) |
| #define RISC_SEMAPHORE_CLR (RISC_SEMAPHORE_WE | 0x0UL) |
| #define RISC_SEMAPHORE_SET (RISC_SEMAPHORE_WE | RISC_SEMAPHORE) |
| |
| #define RISC_SEMAPHORE_FORCE 0x8000UL |
| #define RISC_SEMAPHORE_FORCE_WE (RISC_SEMAPHORE_FORCE << 16) |
| #define RISC_SEMAPHORE_FORCE_CLR (RISC_SEMAPHORE_FORCE_WE | 0x0UL) |
| #define RISC_SEMAPHORE_FORCE_SET \ |
| (RISC_SEMAPHORE_FORCE_WE | RISC_SEMAPHORE_FORCE) |
| |
| /* RISC semaphore timeouts (ms) */ |
| #define TIMEOUT_SEMAPHORE 2500 |
| #define TIMEOUT_SEMAPHORE_FORCE 2000 |
| #define TIMEOUT_TOTAL_ELAPSED 4500 |
| |
| /* Trace Control *************************************************************/ |
| |
| #define TC_AEN_DISABLE 0 |
| |
| #define TC_EFT_ENABLE 4 |
| #define TC_EFT_DISABLE 5 |
| |
| #define TC_FCE_ENABLE 8 |
| #define TC_FCE_OPTIONS 0 |
| #define TC_FCE_DEFAULT_RX_SIZE 2112 |
| #define TC_FCE_DEFAULT_TX_SIZE 2112 |
| #define TC_FCE_DISABLE 9 |
| #define TC_FCE_DISABLE_TRACE BIT_0 |
| |
| /* MID Support ***************************************************************/ |
| |
| #define MIN_MULTI_ID_FABRIC 64 /* Must be power-of-2. */ |
| #define MAX_MULTI_ID_FABRIC 256 /* ... */ |
| |
| struct mid_conf_entry_24xx { |
| uint16_t reserved_1; |
| |
| /* |
| * BIT 0 = Enable Hard Loop Id |
| * BIT 1 = Acquire Loop ID in LIPA |
| * BIT 2 = ID not Acquired |
| * BIT 3 = Enable VP |
| * BIT 4 = Enable Initiator Mode |
| * BIT 5 = Disable Target Mode |
| * BIT 6-7 = Reserved |
| */ |
| uint8_t options; |
| |
| uint8_t hard_address; |
| |
| uint8_t port_name[WWN_SIZE]; |
| uint8_t node_name[WWN_SIZE]; |
| }; |
| |
| struct mid_init_cb_24xx { |
| struct init_cb_24xx init_cb; |
| |
| uint16_t count; |
| uint16_t options; |
| |
| struct mid_conf_entry_24xx entries[MAX_MULTI_ID_FABRIC]; |
| }; |
| |
| |
| struct mid_db_entry_24xx { |
| uint16_t status; |
| #define MDBS_NON_PARTIC BIT_3 |
| #define MDBS_ID_ACQUIRED BIT_1 |
| #define MDBS_ENABLED BIT_0 |
| |
| uint8_t options; |
| uint8_t hard_address; |
| |
| uint8_t port_name[WWN_SIZE]; |
| uint8_t node_name[WWN_SIZE]; |
| |
| uint8_t port_id[3]; |
| uint8_t reserved_1; |
| }; |
| |
| /* |
| * Virtual Port Control IOCB |
| */ |
| #define VP_CTRL_IOCB_TYPE 0x30 /* Virtual Port Control entry. */ |
| struct vp_ctrl_entry_24xx { |
| uint8_t entry_type; /* Entry type. */ |
| uint8_t entry_count; /* Entry count. */ |
| uint8_t sys_define; /* System defined. */ |
| uint8_t entry_status; /* Entry Status. */ |
| |
| uint32_t handle; /* System handle. */ |
| |
| uint16_t vp_idx_failed; |
| |
| uint16_t comp_status; /* Completion status. */ |
| #define CS_VCE_IOCB_ERROR 0x01 /* Error processing IOCB */ |
| #define CS_VCE_ACQ_ID_ERROR 0x02 /* Error while acquireing ID. */ |
| #define CS_VCE_BUSY 0x05 /* Firmware not ready to accept cmd. */ |
| |
| uint16_t command; |
| #define VCE_COMMAND_ENABLE_VPS 0x00 /* Enable VPs. */ |
| #define VCE_COMMAND_DISABLE_VPS 0x08 /* Disable VPs. */ |
| #define VCE_COMMAND_DISABLE_VPS_REINIT 0x09 /* Disable VPs and reinit link. */ |
| #define VCE_COMMAND_DISABLE_VPS_LOGO 0x0a /* Disable VPs and LOGO ports. */ |
| #define VCE_COMMAND_DISABLE_VPS_LOGO_ALL 0x0b /* Disable VPs and LOGO ports. */ |
| |
| uint16_t vp_count; |
| |
| uint8_t vp_idx_map[16]; |
| uint16_t flags; |
| uint16_t id; |
| uint16_t reserved_4; |
| uint16_t hopct; |
| uint8_t reserved_5[24]; |
| }; |
| |
| /* |
| * Modify Virtual Port Configuration IOCB |
| */ |
| #define VP_CONFIG_IOCB_TYPE 0x31 /* Virtual Port Config entry. */ |
| struct vp_config_entry_24xx { |
| uint8_t entry_type; /* Entry type. */ |
| uint8_t entry_count; /* Entry count. */ |
| uint8_t handle_count; |
| uint8_t entry_status; /* Entry Status. */ |
| |
| uint32_t handle; /* System handle. */ |
| |
| uint16_t flags; |
| #define CS_VF_BIND_VPORTS_TO_VF BIT_0 |
| #define CS_VF_SET_QOS_OF_VPORTS BIT_1 |
| #define CS_VF_SET_HOPS_OF_VPORTS BIT_2 |
| |
| uint16_t comp_status; /* Completion status. */ |
| #define CS_VCT_STS_ERROR 0x01 /* Specified VPs were not disabled. */ |
| #define CS_VCT_CNT_ERROR 0x02 /* Invalid VP count. */ |
| #define CS_VCT_ERROR 0x03 /* Unknown error. */ |
| #define CS_VCT_IDX_ERROR 0x02 /* Invalid VP index. */ |
| #define CS_VCT_BUSY 0x05 /* Firmware not ready to accept cmd. */ |
| |
| uint8_t command; |
| #define VCT_COMMAND_MOD_VPS 0x00 /* Modify VP configurations. */ |
| #define VCT_COMMAND_MOD_ENABLE_VPS 0x01 /* Modify configuration & enable VPs. */ |
| |
| uint8_t vp_count; |
| |
| uint8_t vp_index1; |
| uint8_t vp_index2; |
| |
| uint8_t options_idx1; |
| uint8_t hard_address_idx1; |
| uint16_t reserved_vp1; |
| uint8_t port_name_idx1[WWN_SIZE]; |
| uint8_t node_name_idx1[WWN_SIZE]; |
| |
| uint8_t options_idx2; |
| uint8_t hard_address_idx2; |
| uint16_t reserved_vp2; |
| uint8_t port_name_idx2[WWN_SIZE]; |
| uint8_t node_name_idx2[WWN_SIZE]; |
| uint16_t id; |
| uint16_t reserved_4; |
| uint16_t hopct; |
| uint8_t reserved_5[2]; |
| }; |
| |
| #define VP_RPT_ID_IOCB_TYPE 0x32 /* Report ID Acquisition entry. */ |
| enum VP_STATUS { |
| VP_STAT_COMPL, |
| VP_STAT_FAIL, |
| VP_STAT_ID_CHG, |
| VP_STAT_SNS_TO, /* timeout */ |
| VP_STAT_SNS_RJT, |
| VP_STAT_SCR_TO, /* timeout */ |
| VP_STAT_SCR_RJT, |
| }; |
| |
| enum VP_FLAGS { |
| VP_FLAGS_CON_FLOOP = 1, |
| VP_FLAGS_CON_P2P = 2, |
| VP_FLAGS_CON_FABRIC = 3, |
| VP_FLAGS_NAME_VALID = BIT_5, |
| }; |
| |
| struct vp_rpt_id_entry_24xx { |
| uint8_t entry_type; /* Entry type. */ |
| uint8_t entry_count; /* Entry count. */ |
| uint8_t sys_define; /* System defined. */ |
| uint8_t entry_status; /* Entry Status. */ |
| uint32_t resv1; |
| uint8_t vp_acquired; |
| uint8_t vp_setup; |
| uint8_t vp_idx; /* Format 0=reserved */ |
| uint8_t vp_status; /* Format 0=reserved */ |
| |
| uint8_t port_id[3]; |
| uint8_t format; |
| union { |
| struct { |
| /* format 0 loop */ |
| uint8_t vp_idx_map[16]; |
| uint8_t reserved_4[32]; |
| } f0; |
| struct { |
| /* format 1 fabric */ |
| uint8_t vpstat1_subcode; /* vp_status=1 subcode */ |
| uint8_t flags; |
| uint16_t fip_flags; |
| uint8_t rsv2[12]; |
| |
| uint8_t ls_rjt_vendor; |
| uint8_t ls_rjt_explanation; |
| uint8_t ls_rjt_reason; |
| uint8_t rsv3[5]; |
| |
| uint8_t port_name[8]; |
| uint8_t node_name[8]; |
| uint16_t bbcr; |
| uint8_t reserved_5[6]; |
| } f1; |
| struct { /* format 2: N2N direct connect */ |
| uint8_t vpstat1_subcode; |
| uint8_t flags; |
| uint16_t rsv6; |
| uint8_t rsv2[12]; |
| |
| uint8_t ls_rjt_vendor; |
| uint8_t ls_rjt_explanation; |
| uint8_t ls_rjt_reason; |
| uint8_t rsv3[5]; |
| |
| uint8_t port_name[8]; |
| uint8_t node_name[8]; |
| uint32_t remote_nport_id; |
| uint32_t reserved_5; |
| } f2; |
| } u; |
| }; |
| |
| #define VF_EVFP_IOCB_TYPE 0x26 /* Exchange Virtual Fabric Parameters entry. */ |
| struct vf_evfp_entry_24xx { |
| uint8_t entry_type; /* Entry type. */ |
| uint8_t entry_count; /* Entry count. */ |
| uint8_t sys_define; /* System defined. */ |
| uint8_t entry_status; /* Entry Status. */ |
| |
| uint32_t handle; /* System handle. */ |
| uint16_t comp_status; /* Completion status. */ |
| uint16_t timeout; /* timeout */ |
| uint16_t adim_tagging_mode; |
| |
| uint16_t vfport_id; |
| uint32_t exch_addr; |
| |
| uint16_t nport_handle; /* N_PORT handle. */ |
| uint16_t control_flags; |
| uint32_t io_parameter_0; |
| uint32_t io_parameter_1; |
| uint32_t tx_address[2]; /* Data segment 0 address. */ |
| uint32_t tx_len; /* Data segment 0 length. */ |
| uint32_t rx_address[2]; /* Data segment 1 address. */ |
| uint32_t rx_len; /* Data segment 1 length. */ |
| }; |
| |
| /* END MID Support ***********************************************************/ |
| |
| /* Flash Description Table ***************************************************/ |
| |
| struct qla_fdt_layout { |
| uint8_t sig[4]; |
| uint16_t version; |
| uint16_t len; |
| uint16_t checksum; |
| uint8_t unused1[2]; |
| uint8_t model[16]; |
| uint16_t man_id; |
| uint16_t id; |
| uint8_t flags; |
| uint8_t erase_cmd; |
| uint8_t alt_erase_cmd; |
| uint8_t wrt_enable_cmd; |
| uint8_t wrt_enable_bits; |
| uint8_t wrt_sts_reg_cmd; |
| uint8_t unprotect_sec_cmd; |
| uint8_t read_man_id_cmd; |
| uint32_t block_size; |
| uint32_t alt_block_size; |
| uint32_t flash_size; |
| uint32_t wrt_enable_data; |
| uint8_t read_id_addr_len; |
| uint8_t wrt_disable_bits; |
| uint8_t read_dev_id_len; |
| uint8_t chip_erase_cmd; |
| uint16_t read_timeout; |
| uint8_t protect_sec_cmd; |
| uint8_t unused2[65]; |
| }; |
| |
| /* Flash Layout Table ********************************************************/ |
| |
| struct qla_flt_location { |
| uint8_t sig[4]; |
| uint16_t start_lo; |
| uint16_t start_hi; |
| uint8_t version; |
| uint8_t unused[5]; |
| uint16_t checksum; |
| }; |
| |
| struct qla_flt_header { |
| uint16_t version; |
| uint16_t length; |
| uint16_t checksum; |
| uint16_t unused; |
| }; |
| |
| #define FLT_REG_FW 0x01 |
| #define FLT_REG_BOOT_CODE 0x07 |
| #define FLT_REG_VPD_0 0x14 |
| #define FLT_REG_NVRAM_0 0x15 |
| #define FLT_REG_VPD_1 0x16 |
| #define FLT_REG_NVRAM_1 0x17 |
| #define FLT_REG_VPD_2 0xD4 |
| #define FLT_REG_NVRAM_2 0xD5 |
| #define FLT_REG_VPD_3 0xD6 |
| #define FLT_REG_NVRAM_3 0xD7 |
| #define FLT_REG_FDT 0x1a |
| #define FLT_REG_FLT 0x1c |
| #define FLT_REG_HW_EVENT_0 0x1d |
| #define FLT_REG_HW_EVENT_1 0x1f |
| #define FLT_REG_NPIV_CONF_0 0x29 |
| #define FLT_REG_NPIV_CONF_1 0x2a |
| #define FLT_REG_GOLD_FW 0x2f |
| #define FLT_REG_FCP_PRIO_0 0x87 |
| #define FLT_REG_FCP_PRIO_1 0x88 |
| #define FLT_REG_CNA_FW 0x97 |
| #define FLT_REG_BOOT_CODE_8044 0xA2 |
| #define FLT_REG_FCOE_FW 0xA4 |
| #define FLT_REG_FCOE_NVRAM_0 0xAA |
| #define FLT_REG_FCOE_NVRAM_1 0xAC |
| |
| /* 27xx */ |
| #define FLT_REG_IMG_PRI_27XX 0x95 |
| #define FLT_REG_IMG_SEC_27XX 0x96 |
| #define FLT_REG_FW_SEC_27XX 0x02 |
| #define FLT_REG_BOOTLOAD_SEC_27XX 0x9 |
| #define FLT_REG_VPD_SEC_27XX_0 0x50 |
| #define FLT_REG_VPD_SEC_27XX_1 0x52 |
| #define FLT_REG_VPD_SEC_27XX_2 0xD8 |
| #define FLT_REG_VPD_SEC_27XX_3 0xDA |
| |
| struct qla_flt_region { |
| uint32_t code; |
| uint32_t size; |
| uint32_t start; |
| uint32_t end; |
| }; |
| |
| /* Flash NPIV Configuration Table ********************************************/ |
| |
| struct qla_npiv_header { |
| uint8_t sig[2]; |
| uint16_t version; |
| uint16_t entries; |
| uint16_t unused[4]; |
| uint16_t checksum; |
| }; |
| |
| struct qla_npiv_entry { |
| uint16_t flags; |
| uint16_t vf_id; |
| uint8_t q_qos; |
| uint8_t f_qos; |
| uint16_t unused1; |
| uint8_t port_name[WWN_SIZE]; |
| uint8_t node_name[WWN_SIZE]; |
| }; |
| |
| /* 84XX Support **************************************************************/ |
| |
| #define MBA_ISP84XX_ALERT 0x800f /* Alert Notification. */ |
| #define A84_PANIC_RECOVERY 0x1 |
| #define A84_OP_LOGIN_COMPLETE 0x2 |
| #define A84_DIAG_LOGIN_COMPLETE 0x3 |
| #define A84_GOLD_LOGIN_COMPLETE 0x4 |
| |
| #define MBC_ISP84XX_RESET 0x3a /* Reset. */ |
| |
| #define FSTATE_REMOTE_FC_DOWN BIT_0 |
| #define FSTATE_NSL_LINK_DOWN BIT_1 |
| #define FSTATE_IS_DIAG_FW BIT_2 |
| #define FSTATE_LOGGED_IN BIT_3 |
| #define FSTATE_WAITING_FOR_VERIFY BIT_4 |
| |
| #define VERIFY_CHIP_IOCB_TYPE 0x1B |
| struct verify_chip_entry_84xx { |
| uint8_t entry_type; |
| uint8_t entry_count; |
| uint8_t sys_defined; |
| uint8_t entry_status; |
| |
| uint32_t handle; |
| |
| uint16_t options; |
| #define VCO_DONT_UPDATE_FW BIT_0 |
| #define VCO_FORCE_UPDATE BIT_1 |
| #define VCO_DONT_RESET_UPDATE BIT_2 |
| #define VCO_DIAG_FW BIT_3 |
| #define VCO_END_OF_DATA BIT_14 |
| #define VCO_ENABLE_DSD BIT_15 |
| |
| uint16_t reserved_1; |
| |
| uint16_t data_seg_cnt; |
| uint16_t reserved_2[3]; |
| |
| uint32_t fw_ver; |
| uint32_t exchange_address; |
| |
| uint32_t reserved_3[3]; |
| uint32_t fw_size; |
| uint32_t fw_seq_size; |
| uint32_t relative_offset; |
| |
| uint32_t dseg_address[2]; |
| uint32_t dseg_length; |
| }; |
| |
| struct verify_chip_rsp_84xx { |
| uint8_t entry_type; |
| uint8_t entry_count; |
| uint8_t sys_defined; |
| uint8_t entry_status; |
| |
| uint32_t handle; |
| |
| uint16_t comp_status; |
| #define CS_VCS_CHIP_FAILURE 0x3 |
| #define CS_VCS_BAD_EXCHANGE 0x8 |
| #define CS_VCS_SEQ_COMPLETEi 0x40 |
| |
| uint16_t failure_code; |
| #define VFC_CHECKSUM_ERROR 0x1 |
| #define VFC_INVALID_LEN 0x2 |
| #define VFC_ALREADY_IN_PROGRESS 0x8 |
| |
| uint16_t reserved_1[4]; |
| |
| uint32_t fw_ver; |
| uint32_t exchange_address; |
| |
| uint32_t reserved_2[6]; |
| }; |
| |
| #define ACCESS_CHIP_IOCB_TYPE 0x2B |
| struct access_chip_84xx { |
| uint8_t entry_type; |
| uint8_t entry_count; |
| uint8_t sys_defined; |
| uint8_t entry_status; |
| |
| uint32_t handle; |
| |
| uint16_t options; |
| #define ACO_DUMP_MEMORY 0x0 |
| #define ACO_LOAD_MEMORY 0x1 |
| #define ACO_CHANGE_CONFIG_PARAM 0x2 |
| #define ACO_REQUEST_INFO 0x3 |
| |
| uint16_t reserved1; |
| |
| uint16_t dseg_count; |
| uint16_t reserved2[3]; |
| |
| uint32_t parameter1; |
| uint32_t parameter2; |
| uint32_t parameter3; |
| |
| uint32_t reserved3[3]; |
| uint32_t total_byte_cnt; |
| uint32_t reserved4; |
| |
| uint32_t dseg_address[2]; |
| uint32_t dseg_length; |
| }; |
| |
| struct access_chip_rsp_84xx { |
| uint8_t entry_type; |
| uint8_t entry_count; |
| uint8_t sys_defined; |
| uint8_t entry_status; |
| |
| uint32_t handle; |
| |
| uint16_t comp_status; |
| uint16_t failure_code; |
| uint32_t residual_count; |
| |
| uint32_t reserved[12]; |
| }; |
| |
| /* 81XX Support **************************************************************/ |
| |
| #define MBA_DCBX_START 0x8016 |
| #define MBA_DCBX_COMPLETE 0x8030 |
| #define MBA_FCF_CONF_ERR 0x8031 |
| #define MBA_DCBX_PARAM_UPDATE 0x8032 |
| #define MBA_IDC_COMPLETE 0x8100 |
| #define MBA_IDC_NOTIFY 0x8101 |
| #define MBA_IDC_TIME_EXT 0x8102 |
| |
| #define MBC_IDC_ACK 0x101 |
| #define MBC_RESTART_MPI_FW 0x3d |
| #define MBC_FLASH_ACCESS_CTRL 0x3e /* Control flash access. */ |
| #define MBC_GET_XGMAC_STATS 0x7a |
| #define MBC_GET_DCBX_PARAMS 0x51 |
| |
| /* |
| * ISP83xx mailbox commands |
| */ |
| #define MBC_WRITE_REMOTE_REG 0x0001 /* Write remote register */ |
| #define MBC_READ_REMOTE_REG 0x0009 /* Read remote register */ |
| #define MBC_RESTART_NIC_FIRMWARE 0x003d /* Restart NIC firmware */ |
| #define MBC_SET_ACCESS_CONTROL 0x003e /* Access control command */ |
| |
| /* Flash access control option field bit definitions */ |
| #define FAC_OPT_FORCE_SEMAPHORE BIT_15 |
| #define FAC_OPT_REQUESTOR_ID BIT_14 |
| #define FAC_OPT_CMD_SUBCODE 0xff |
| |
| /* Flash access control command subcodes */ |
| #define FAC_OPT_CMD_WRITE_PROTECT 0x00 |
| #define FAC_OPT_CMD_WRITE_ENABLE 0x01 |
| #define FAC_OPT_CMD_ERASE_SECTOR 0x02 |
| #define FAC_OPT_CMD_LOCK_SEMAPHORE 0x03 |
| #define FAC_OPT_CMD_UNLOCK_SEMAPHORE 0x04 |
| #define FAC_OPT_CMD_GET_SECTOR_SIZE 0x05 |
| |
| struct nvram_81xx { |
| /* NVRAM header. */ |
| uint8_t id[4]; |
| uint16_t nvram_version; |
| uint16_t reserved_0; |
| |
| /* Firmware Initialization Control Block. */ |
| uint16_t version; |
| uint16_t reserved_1; |
| uint16_t frame_payload_size; |
| uint16_t execution_throttle; |
| uint16_t exchange_count; |
| uint16_t reserved_2; |
| |
| uint8_t port_name[WWN_SIZE]; |
| uint8_t node_name[WWN_SIZE]; |
| |
| uint16_t login_retry_count; |
| uint16_t reserved_3; |
| uint16_t interrupt_delay_timer; |
| uint16_t login_timeout; |
| |
| uint32_t firmware_options_1; |
| uint32_t firmware_options_2; |
| uint32_t firmware_options_3; |
| |
| uint16_t reserved_4[4]; |
| |
| /* Offset 64. */ |
| uint8_t enode_mac[6]; |
| uint16_t reserved_5[5]; |
| |
| /* Offset 80. */ |
| uint16_t reserved_6[24]; |
| |
| /* Offset 128. */ |
| uint16_t ex_version; |
| uint8_t prio_fcf_matching_flags; |
| uint8_t reserved_6_1[3]; |
| uint16_t pri_fcf_vlan_id; |
| uint8_t pri_fcf_fabric_name[8]; |
| uint16_t reserved_6_2[7]; |
| uint8_t spma_mac_addr[6]; |
| uint16_t reserved_6_3[14]; |
| |
| /* Offset 192. */ |
| uint16_t reserved_7[32]; |
| |
| /* |
| * BIT 0 = Enable spinup delay |
| * BIT 1 = Disable BIOS |
| * BIT 2 = Enable Memory Map BIOS |
| * BIT 3 = Enable Selectable Boot |
| * BIT 4 = Disable RISC code load |
| * BIT 5 = Disable Serdes |
| * BIT 6 = Opt boot mode |
| * BIT 7 = Interrupt enable |
| * |
| * BIT 8 = EV Control enable |
| * BIT 9 = Enable lip reset |
| * BIT 10 = Enable lip full login |
| * BIT 11 = Enable target reset |
| * BIT 12 = Stop firmware |
| * BIT 13 = Enable nodename option |
| * BIT 14 = Default WWPN valid |
| * BIT 15 = Enable alternate WWN |
| * |
| * BIT 16 = CLP LUN string |
| * BIT 17 = CLP Target string |
| * BIT 18 = CLP BIOS enable string |
| * BIT 19 = CLP Serdes string |
| * BIT 20 = CLP WWPN string |
| * BIT 21 = CLP WWNN string |
| * BIT 22 = |
| * BIT 23 = |
| * BIT 24 = Keep WWPN |
| * BIT 25 = Temp WWPN |
| * BIT 26-31 = |
| */ |
| uint32_t host_p; |
| |
| uint8_t alternate_port_name[WWN_SIZE]; |
| uint8_t alternate_node_name[WWN_SIZE]; |
| |
| uint8_t boot_port_name[WWN_SIZE]; |
| uint16_t boot_lun_number; |
| uint16_t reserved_8; |
| |
| uint8_t alt1_boot_port_name[WWN_SIZE]; |
| uint16_t alt1_boot_lun_number; |
| uint16_t reserved_9; |
| |
| uint8_t alt2_boot_port_name[WWN_SIZE]; |
| uint16_t alt2_boot_lun_number; |
| uint16_t reserved_10; |
| |
| uint8_t alt3_boot_port_name[WWN_SIZE]; |
| uint16_t alt3_boot_lun_number; |
| uint16_t reserved_11; |
| |
| /* |
| * BIT 0 = Selective Login |
| * BIT 1 = Alt-Boot Enable |
| * BIT 2 = Reserved |
| * BIT 3 = Boot Order List |
| * BIT 4 = Reserved |
| * BIT 5 = Selective LUN |
| * BIT 6 = Reserved |
| * BIT 7-31 = |
| */ |
| uint32_t efi_parameters; |
| |
| uint8_t reset_delay; |
| uint8_t reserved_12; |
| uint16_t reserved_13; |
| |
| uint16_t boot_id_number; |
| uint16_t reserved_14; |
| |
| uint16_t max_luns_per_target; |
| uint16_t reserved_15; |
| |
| uint16_t port_down_retry_count; |
| uint16_t link_down_timeout; |
| |
| /* FCode parameters. */ |
| uint16_t fcode_parameter; |
| |
| uint16_t reserved_16[3]; |
| |
| /* Offset 352. */ |
| uint8_t reserved_17[4]; |
| uint16_t reserved_18[5]; |
| uint8_t reserved_19[2]; |
| uint16_t reserved_20[8]; |
| |
| /* Offset 384. */ |
| uint8_t reserved_21[16]; |
| uint16_t reserved_22[3]; |
| |
| /* |
| * BIT 0 = Extended BB credits for LR |
| * BIT 1 = Virtual Fabric Enable |
| * BIT 2 = Enhanced Features Unused |
| * BIT 3-7 = Enhanced Features Reserved |
| */ |
| /* Enhanced Features */ |
| uint8_t enhanced_features; |
| |
| uint8_t reserved_23; |
| uint16_t reserved_24[4]; |
| |
| /* Offset 416. */ |
| uint16_t reserved_25[32]; |
| |
| /* Offset 480. */ |
| uint8_t model_name[16]; |
| |
| /* Offset 496. */ |
| uint16_t feature_mask_l; |
| uint16_t feature_mask_h; |
| uint16_t reserved_26[2]; |
| |
| uint16_t subsystem_vendor_id; |
| uint16_t subsystem_device_id; |
| |
| uint32_t checksum; |
| }; |
| |
| /* |
| * ISP Initialization Control Block. |
| * Little endian except where noted. |
| */ |
| #define ICB_VERSION 1 |
| struct init_cb_81xx { |
| uint16_t version; |
| uint16_t reserved_1; |
| |
| uint16_t frame_payload_size; |
| uint16_t execution_throttle; |
| uint16_t exchange_count; |
| |
| uint16_t reserved_2; |
| |
| uint8_t port_name[WWN_SIZE]; /* Big endian. */ |
| uint8_t node_name[WWN_SIZE]; /* Big endian. */ |
| |
| uint16_t response_q_inpointer; |
| uint16_t request_q_outpointer; |
| |
| uint16_t login_retry_count; |
| |
| uint16_t prio_request_q_outpointer; |
| |
| uint16_t response_q_length; |
| uint16_t request_q_length; |
| |
| uint16_t reserved_3; |
| |
| uint16_t prio_request_q_length; |
| |
| uint32_t request_q_address[2]; |
| uint32_t response_q_address[2]; |
| uint32_t prio_request_q_address[2]; |
| |
| uint8_t reserved_4[8]; |
| |
| uint16_t atio_q_inpointer; |
| uint16_t atio_q_length; |
| uint32_t atio_q_address[2]; |
| |
| uint16_t interrupt_delay_timer; /* 100us increments. */ |
| uint16_t login_timeout; |
| |
| /* |
| * BIT 0-3 = Reserved |
| * BIT 4 = Enable Target Mode |
| * BIT 5 = Disable Initiator Mode |
| * BIT 6 = Reserved |
| * BIT 7 = Reserved |
| * |
| * BIT 8-13 = Reserved |
| * BIT 14 = Node Name Option |
| * BIT 15-31 = Reserved |
| */ |
| uint32_t firmware_options_1; |
| |
| /* |
| * BIT 0 = Operation Mode bit 0 |
| * BIT 1 = Operation Mode bit 1 |
| * BIT 2 = Operation Mode bit 2 |
| * BIT 3 = Operation Mode bit 3 |
| * BIT 4-7 = Reserved |
| * |
| * BIT 8 = Enable Class 2 |
| * BIT 9 = Enable ACK0 |
| * BIT 10 = Reserved |
| * BIT 11 = Enable FC-SP Security |
| * BIT 12 = FC Tape Enable |
| * BIT 13 = Reserved |
| * BIT 14 = Enable Target PRLI Control |
| * BIT 15-31 = Reserved |
| */ |
| uint32_t firmware_options_2; |
| |
| /* |
| * BIT 0-3 = Reserved |
| * BIT 4 = FCP RSP Payload bit 0 |
| * BIT 5 = FCP RSP Payload bit 1 |
| * BIT 6 = Enable Receive Out-of-Order data frame handling |
| * BIT 7 = Reserved |
| * |
| * BIT 8 = Reserved |
| * BIT 9 = Enable Out-of-Order FCP_XFER_RDY relative offset handling |
| * BIT 10-16 = Reserved |
| * BIT 17 = Enable multiple FCFs |
| * BIT 18-20 = MAC addressing mode |
| * BIT 21-25 = Ethernet data rate |
| * BIT 26 = Enable ethernet header rx IOCB for ATIO q |
| * BIT 27 = Enable ethernet header rx IOCB for response q |
| * BIT 28 = SPMA selection bit 0 |
| * BIT 28 = SPMA selection bit 1 |
| * BIT 30-31 = Reserved |
| */ |
| uint32_t firmware_options_3; |
| |
| uint8_t reserved_5[8]; |
| |
| uint8_t enode_mac[6]; |
| |
| uint8_t reserved_6[10]; |
| }; |
| |
| struct mid_init_cb_81xx { |
| struct init_cb_81xx init_cb; |
| |
| uint16_t count; |
| uint16_t options; |
| |
| struct mid_conf_entry_24xx entries[MAX_MULTI_ID_FABRIC]; |
| }; |
| |
| struct ex_init_cb_81xx { |
| uint16_t ex_version; |
| uint8_t prio_fcf_matching_flags; |
| uint8_t reserved_1[3]; |
| uint16_t pri_fcf_vlan_id; |
| uint8_t pri_fcf_fabric_name[8]; |
| uint16_t reserved_2[7]; |
| uint8_t spma_mac_addr[6]; |
| uint16_t reserved_3[14]; |
| }; |
| |
| #define FARX_ACCESS_FLASH_CONF_81XX 0x7FFD0000 |
| #define FARX_ACCESS_FLASH_DATA_81XX 0x7F800000 |
| |
| /* FCP priority config defines *************************************/ |
| /* operations */ |
| #define QLFC_FCP_PRIO_DISABLE 0x0 |
| #define QLFC_FCP_PRIO_ENABLE 0x1 |
| #define QLFC_FCP_PRIO_GET_CONFIG 0x2 |
| #define QLFC_FCP_PRIO_SET_CONFIG 0x3 |
| |
| struct qla_fcp_prio_entry { |
| uint16_t flags; /* Describes parameter(s) in FCP */ |
| /* priority entry that are valid */ |
| #define FCP_PRIO_ENTRY_VALID 0x1 |
| #define FCP_PRIO_ENTRY_TAG_VALID 0x2 |
| #define FCP_PRIO_ENTRY_SPID_VALID 0x4 |
| #define FCP_PRIO_ENTRY_DPID_VALID 0x8 |
| #define FCP_PRIO_ENTRY_LUNB_VALID 0x10 |
| #define FCP_PRIO_ENTRY_LUNE_VALID 0x20 |
| #define FCP_PRIO_ENTRY_SWWN_VALID 0x40 |
| #define FCP_PRIO_ENTRY_DWWN_VALID 0x80 |
| uint8_t tag; /* Priority value */ |
| uint8_t reserved; /* Reserved for future use */ |
| uint32_t src_pid; /* Src port id. high order byte */ |
| /* unused; -1 (wild card) */ |
| uint32_t dst_pid; /* Src port id. high order byte */ |
| /* unused; -1 (wild card) */ |
| uint16_t lun_beg; /* 1st lun num of lun range. */ |
| /* -1 (wild card) */ |
| uint16_t lun_end; /* 2nd lun num of lun range. */ |
| /* -1 (wild card) */ |
| uint8_t src_wwpn[8]; /* Source WWPN: -1 (wild card) */ |
| uint8_t dst_wwpn[8]; /* Destination WWPN: -1 (wild card) */ |
| }; |
| |
| struct qla_fcp_prio_cfg { |
| uint8_t signature[4]; /* "HQOS" signature of config data */ |
| uint16_t version; /* 1: Initial version */ |
| uint16_t length; /* config data size in num bytes */ |
| uint16_t checksum; /* config data bytes checksum */ |
| uint16_t num_entries; /* Number of entries */ |
| uint16_t size_of_entry; /* Size of each entry in num bytes */ |
| uint8_t attributes; /* enable/disable, persistence */ |
| #define FCP_PRIO_ATTR_DISABLE 0x0 |
| #define FCP_PRIO_ATTR_ENABLE 0x1 |
| #define FCP_PRIO_ATTR_PERSIST 0x2 |
| uint8_t reserved; /* Reserved for future use */ |
| #define FCP_PRIO_CFG_HDR_SIZE 0x10 |
| struct qla_fcp_prio_entry entry[1]; /* fcp priority entries */ |
| #define FCP_PRIO_CFG_ENTRY_SIZE 0x20 |
| }; |
| |
| #define FCP_PRIO_CFG_SIZE (32*1024) /* fcp prio data per port*/ |
| |
| /* 25XX Support ****************************************************/ |
| #define FA_FCP_PRIO0_ADDR_25 0x3C000 |
| #define FA_FCP_PRIO1_ADDR_25 0x3E000 |
| |
| /* 81XX Flash locations -- occupies second 2MB region. */ |
| #define FA_BOOT_CODE_ADDR_81 0x80000 |
| #define FA_RISC_CODE_ADDR_81 0xA0000 |
| #define FA_FW_AREA_ADDR_81 0xC0000 |
| #define FA_VPD_NVRAM_ADDR_81 0xD0000 |
| #define FA_VPD0_ADDR_81 0xD0000 |
| #define FA_VPD1_ADDR_81 0xD0400 |
| #define FA_NVRAM0_ADDR_81 0xD0080 |
| #define FA_NVRAM1_ADDR_81 0xD0180 |
| #define FA_FEATURE_ADDR_81 0xD4000 |
| #define FA_FLASH_DESCR_ADDR_81 0xD8000 |
| #define FA_FLASH_LAYOUT_ADDR_81 0xD8400 |
| #define FA_HW_EVENT0_ADDR_81 0xDC000 |
| #define FA_HW_EVENT1_ADDR_81 0xDC400 |
| #define FA_NPIV_CONF0_ADDR_81 0xD1000 |
| #define FA_NPIV_CONF1_ADDR_81 0xD2000 |
| |
| /* 83XX Flash locations -- occupies second 8MB region. */ |
| #define FA_FLASH_LAYOUT_ADDR_83 0xFC400 |
| |
| #endif |