| #ifndef NETDEV_PCS_H |
| #define NETDEV_PCS_H |
| |
| #include <linux/phy.h> |
| #include <linux/spinlock.h> |
| #include <linux/workqueue.h> |
| |
| struct device_node; |
| struct ethtool_cmd; |
| struct fwnode_handle; |
| struct net_device; |
| |
| enum { |
| MLO_PAUSE_NONE, |
| MLO_PAUSE_ASYM = BIT(0), |
| MLO_PAUSE_SYM = BIT(1), |
| MLO_PAUSE_RX = BIT(2), |
| MLO_PAUSE_TX = BIT(3), |
| MLO_PAUSE_TXRX_MASK = MLO_PAUSE_TX | MLO_PAUSE_RX, |
| MLO_PAUSE_AN = BIT(4), |
| |
| MLO_AN_PHY = 0, /* Conventional PHY */ |
| MLO_AN_FIXED, /* Fixed-link mode */ |
| MLO_AN_INBAND, /* In-band protocol */ |
| }; |
| |
| static inline bool phylink_autoneg_inband(unsigned int mode) |
| { |
| return mode == MLO_AN_INBAND; |
| } |
| |
| /** |
| * struct phylink_link_state - link state structure |
| * @advertising: ethtool bitmask containing advertised link modes |
| * @lp_advertising: ethtool bitmask containing link partner advertised link |
| * modes |
| * @interface: link &typedef phy_interface_t mode |
| * @speed: link speed, one of the SPEED_* constants. |
| * @duplex: link duplex mode, one of DUPLEX_* constants. |
| * @pause: link pause state, described by MLO_PAUSE_* constants. |
| * @link: true if the link is up. |
| * @an_enabled: true if autonegotiation is enabled/desired. |
| * @an_complete: true if autonegotiation has completed. |
| */ |
| struct phylink_link_state { |
| __ETHTOOL_DECLARE_LINK_MODE_MASK(advertising); |
| __ETHTOOL_DECLARE_LINK_MODE_MASK(lp_advertising); |
| phy_interface_t interface; |
| int speed; |
| int duplex; |
| int pause; |
| unsigned int link:1; |
| unsigned int an_enabled:1; |
| unsigned int an_complete:1; |
| }; |
| |
| /** |
| * struct phylink_mac_ops - MAC operations structure. |
| * @validate: Validate and update the link configuration. |
| * @mac_link_state: Read the current link state from the hardware. |
| * @mac_config: configure the MAC for the selected mode and state. |
| * @mac_an_restart: restart 802.3z BaseX autonegotiation. |
| * @mac_link_down: take the link down. |
| * @mac_link_up: allow the link to come up. |
| * |
| * The individual methods are described more fully below. |
| */ |
| struct phylink_mac_ops { |
| void (*validate)(struct net_device *ndev, unsigned long *supported, |
| struct phylink_link_state *state); |
| int (*mac_link_state)(struct net_device *ndev, |
| struct phylink_link_state *state); |
| void (*mac_config)(struct net_device *ndev, unsigned int mode, |
| const struct phylink_link_state *state); |
| void (*mac_an_restart)(struct net_device *ndev); |
| void (*mac_link_down)(struct net_device *ndev, unsigned int mode, |
| phy_interface_t interface); |
| void (*mac_link_up)(struct net_device *ndev, unsigned int mode, |
| phy_interface_t interface, |
| struct phy_device *phy); |
| }; |
| |
| #if 0 /* For kernel-doc purposes only. */ |
| /** |
| * validate - Validate and update the link configuration |
| * @ndev: a pointer to a &struct net_device for the MAC. |
| * @supported: ethtool bitmask for supported link modes. |
| * @state: a pointer to a &struct phylink_link_state. |
| * |
| * Clear bits in the @supported and @state->advertising masks that |
| * are not supportable by the MAC. |
| * |
| * Note that the PHY may be able to transform from one connection |
| * technology to another, so, eg, don't clear 1000BaseX just |
| * because the MAC is unable to BaseX mode. This is more about |
| * clearing unsupported speeds and duplex settings. |
| * |
| * If the @state->interface mode is %PHY_INTERFACE_MODE_1000BASEX |
| * or %PHY_INTERFACE_MODE_2500BASEX, select the appropriate mode |
| * based on @state->advertising and/or @state->speed and update |
| * @state->interface accordingly. |
| */ |
| void validate(struct net_device *ndev, unsigned long *supported, |
| struct phylink_link_state *state); |
| |
| /** |
| * mac_link_state() - Read the current link state from the hardware |
| * @ndev: a pointer to a &struct net_device for the MAC. |
| * @state: a pointer to a &struct phylink_link_state. |
| * |
| * Read the current link state from the MAC, reporting the current |
| * speed in @state->speed, duplex mode in @state->duplex, pause mode |
| * in @state->pause using the %MLO_PAUSE_RX and %MLO_PAUSE_TX bits, |
| * negotiation completion state in @state->an_complete, and link |
| * up state in @state->link. |
| */ |
| int mac_link_state(struct net_device *ndev, |
| struct phylink_link_state *state); |
| |
| /** |
| * mac_config() - configure the MAC for the selected mode and state |
| * @ndev: a pointer to a &struct net_device for the MAC. |
| * @mode: one of %MLO_AN_FIXED, %MLO_AN_PHY, %MLO_AN_INBAND. |
| * @state: a pointer to a &struct phylink_link_state. |
| * |
| * The action performed depends on the currently selected mode: |
| * |
| * %MLO_AN_FIXED, %MLO_AN_PHY: |
| * Configure the specified @state->speed, @state->duplex and |
| * @state->pause (%MLO_PAUSE_TX / %MLO_PAUSE_RX) mode. |
| * |
| * %MLO_AN_INBAND: |
| * place the link in an inband negotiation mode (such as 802.3z |
| * 1000base-X or Cisco SGMII mode depending on the @state->interface |
| * mode). In both cases, link state management (whether the link |
| * is up or not) is performed by the MAC, and reported via the |
| * mac_link_state() callback. Changes in link state must be made |
| * by calling phylink_mac_change(). |
| * |
| * If in 802.3z mode, the link speed is fixed, dependent on the |
| * @state->interface. Duplex is negotiated, and pause is advertised |
| * according to @state->an_enabled, @state->pause and |
| * @state->advertising flags. Beware of MACs which only support full |
| * duplex at gigabit and higher speeds. |
| * |
| * If in Cisco SGMII mode, the link speed and duplex mode are passed |
| * in the serial bitstream 16-bit configuration word, and the MAC |
| * should be configured to read these bits and acknowledge the |
| * configuration word. Nothing is advertised by the MAC. The MAC is |
| * responsible for reading the configuration word and configuring |
| * itself accordingly. |
| * |
| * Implementations are expected to update the MAC to reflect the |
| * requested settings - i.o.w., if nothing has changed between two |
| * calls, no action is expected. If only flow control settings have |
| * changed, flow control should be updated *without* taking the link |
| * down. This "update" behaviour is critical to avoid bouncing the |
| * link up status. |
| */ |
| void mac_config(struct net_device *ndev, unsigned int mode, |
| const struct phylink_link_state *state); |
| |
| /** |
| * mac_an_restart() - restart 802.3z BaseX autonegotiation |
| * @ndev: a pointer to a &struct net_device for the MAC. |
| */ |
| void mac_an_restart(struct net_device *ndev); |
| |
| /** |
| * mac_link_down() - take the link down |
| * @ndev: a pointer to a &struct net_device for the MAC. |
| * @mode: link autonegotiation mode |
| * @interface: link &typedef phy_interface_t mode |
| * |
| * If @mode is not an in-band negotiation mode (as defined by |
| * phylink_autoneg_inband()), force the link down and disable any |
| * Energy Efficient Ethernet MAC configuration. Interface type |
| * selection must be done in mac_config(). |
| */ |
| void mac_link_down(struct net_device *ndev, unsigned int mode, |
| phy_interface_t interface); |
| |
| /** |
| * mac_link_up() - allow the link to come up |
| * @ndev: a pointer to a &struct net_device for the MAC. |
| * @mode: link autonegotiation mode |
| * @interface: link &typedef phy_interface_t mode |
| * @phy: any attached phy |
| * |
| * If @mode is not an in-band negotiation mode (as defined by |
| * phylink_autoneg_inband()), allow the link to come up. If @phy |
| * is non-%NULL, configure Energy Efficient Ethernet by calling |
| * phy_init_eee() and perform appropriate MAC configuration for EEE. |
| * Interface type selection must be done in mac_config(). |
| */ |
| void mac_link_up(struct net_device *ndev, unsigned int mode, |
| phy_interface_t interface, |
| struct phy_device *phy); |
| #endif |
| |
| struct phylink *phylink_create(struct net_device *, struct fwnode_handle *, |
| phy_interface_t iface, const struct phylink_mac_ops *ops); |
| void phylink_destroy(struct phylink *); |
| |
| int phylink_connect_phy(struct phylink *, struct phy_device *); |
| int phylink_of_phy_connect(struct phylink *, struct device_node *, u32 flags); |
| void phylink_disconnect_phy(struct phylink *); |
| int phylink_fixed_state_cb(struct phylink *, |
| void (*cb)(struct net_device *dev, |
| struct phylink_link_state *)); |
| |
| void phylink_mac_change(struct phylink *, bool up); |
| |
| void phylink_start(struct phylink *); |
| void phylink_stop(struct phylink *); |
| |
| void phylink_ethtool_get_wol(struct phylink *, struct ethtool_wolinfo *); |
| int phylink_ethtool_set_wol(struct phylink *, struct ethtool_wolinfo *); |
| |
| int phylink_ethtool_ksettings_get(struct phylink *, |
| struct ethtool_link_ksettings *); |
| int phylink_ethtool_ksettings_set(struct phylink *, |
| const struct ethtool_link_ksettings *); |
| int phylink_ethtool_nway_reset(struct phylink *); |
| void phylink_ethtool_get_pauseparam(struct phylink *, |
| struct ethtool_pauseparam *); |
| int phylink_ethtool_set_pauseparam(struct phylink *, |
| struct ethtool_pauseparam *); |
| int phylink_get_eee_err(struct phylink *); |
| int phylink_init_eee(struct phylink *, bool); |
| int phylink_ethtool_get_eee(struct phylink *, struct ethtool_eee *); |
| int phylink_ethtool_set_eee(struct phylink *, struct ethtool_eee *); |
| int phylink_mii_ioctl(struct phylink *, struct ifreq *, int); |
| |
| #define phylink_zero(bm) \ |
| bitmap_zero(bm, __ETHTOOL_LINK_MODE_MASK_NBITS) |
| #define __phylink_do_bit(op, bm, mode) \ |
| op(ETHTOOL_LINK_MODE_ ## mode ## _BIT, bm) |
| |
| #define phylink_set(bm, mode) __phylink_do_bit(__set_bit, bm, mode) |
| #define phylink_clear(bm, mode) __phylink_do_bit(__clear_bit, bm, mode) |
| #define phylink_test(bm, mode) __phylink_do_bit(test_bit, bm, mode) |
| |
| void phylink_set_port_modes(unsigned long *bits); |
| void phylink_helper_basex_speed(struct phylink_link_state *state); |
| |
| #endif |