| /* | 
 |  *  linux/drivers/acorn/net/ether1.c | 
 |  * | 
 |  *  Copyright (C) 1996-2000 Russell King | 
 |  * | 
 |  * This program is free software; you can redistribute it and/or modify | 
 |  * it under the terms of the GNU General Public License version 2 as | 
 |  * published by the Free Software Foundation. | 
 |  * | 
 |  *  Acorn ether1 driver (82586 chip) for Acorn machines | 
 |  * | 
 |  * We basically keep two queues in the cards memory - one for transmit | 
 |  * and one for receive.  Each has a head and a tail.  The head is where | 
 |  * we/the chip adds packets to be transmitted/received, and the tail | 
 |  * is where the transmitter has got to/where the receiver will stop. | 
 |  * Both of these queues are circular, and since the chip is running | 
 |  * all the time, we have to be careful when we modify the pointers etc | 
 |  * so that the buffer memory contents is valid all the time. | 
 |  * | 
 |  * Change log: | 
 |  * 1.00	RMK			Released | 
 |  * 1.01	RMK	19/03/1996	Transfers the last odd byte onto/off of the card now. | 
 |  * 1.02	RMK	25/05/1997	Added code to restart RU if it goes not ready | 
 |  * 1.03	RMK	14/09/1997	Cleaned up the handling of a reset during the TX interrupt. | 
 |  *				Should prevent lockup. | 
 |  * 1.04 RMK	17/09/1997	Added more info when initialsation of chip goes wrong. | 
 |  *				TDR now only reports failure when chip reports non-zero | 
 |  *				TDR time-distance. | 
 |  * 1.05	RMK	31/12/1997	Removed calls to dev_tint for 2.1 | 
 |  * 1.06	RMK	10/02/2000	Updated for 2.3.43 | 
 |  * 1.07	RMK	13/05/2000	Updated for 2.3.99-pre8 | 
 |  */ | 
 |  | 
 | #include <linux/module.h> | 
 | #include <linux/kernel.h> | 
 | #include <linux/types.h> | 
 | #include <linux/fcntl.h> | 
 | #include <linux/interrupt.h> | 
 | #include <linux/ioport.h> | 
 | #include <linux/in.h> | 
 | #include <linux/slab.h> | 
 | #include <linux/string.h> | 
 | #include <linux/errno.h> | 
 | #include <linux/device.h> | 
 | #include <linux/init.h> | 
 | #include <linux/netdevice.h> | 
 | #include <linux/etherdevice.h> | 
 | #include <linux/skbuff.h> | 
 | #include <linux/bitops.h> | 
 |  | 
 | #include <asm/io.h> | 
 | #include <asm/dma.h> | 
 | #include <asm/ecard.h> | 
 |  | 
 | #define __ETHER1_C | 
 | #include "ether1.h" | 
 |  | 
 | static unsigned int net_debug = NET_DEBUG; | 
 |  | 
 | #define BUFFER_SIZE	0x10000 | 
 | #define TX_AREA_START	0x00100 | 
 | #define TX_AREA_END	0x05000 | 
 | #define RX_AREA_START	0x05000 | 
 | #define RX_AREA_END	0x0fc00 | 
 |  | 
 | static int ether1_open(struct net_device *dev); | 
 | static int ether1_sendpacket(struct sk_buff *skb, struct net_device *dev); | 
 | static irqreturn_t ether1_interrupt(int irq, void *dev_id); | 
 | static int ether1_close(struct net_device *dev); | 
 | static void ether1_setmulticastlist(struct net_device *dev); | 
 | static void ether1_timeout(struct net_device *dev); | 
 |  | 
 | /* ------------------------------------------------------------------------- */ | 
 |  | 
 | static char version[] = "ether1 ethernet driver (c) 2000 Russell King v1.07\n"; | 
 |  | 
 | #define BUS_16 16 | 
 | #define BUS_8  8 | 
 |  | 
 | /* ------------------------------------------------------------------------- */ | 
 |  | 
 | #define DISABLEIRQS 1 | 
 | #define NORMALIRQS  0 | 
 |  | 
 | #define ether1_readw(dev, addr, type, offset, svflgs) ether1_inw_p (dev, addr + (int)(&((type *)0)->offset), svflgs) | 
 | #define ether1_writew(dev, val, addr, type, offset, svflgs) ether1_outw_p (dev, val, addr + (int)(&((type *)0)->offset), svflgs) | 
 |  | 
 | static inline unsigned short | 
 | ether1_inw_p (struct net_device *dev, int addr, int svflgs) | 
 | { | 
 | 	unsigned long flags; | 
 | 	unsigned short ret; | 
 |  | 
 | 	if (svflgs) | 
 | 		local_irq_save (flags); | 
 |  | 
 | 	writeb(addr >> 12, REG_PAGE); | 
 | 	ret = readw(ETHER1_RAM + ((addr & 4095) << 1)); | 
 | 	if (svflgs) | 
 | 		local_irq_restore (flags); | 
 | 	return ret; | 
 | } | 
 |  | 
 | static inline void | 
 | ether1_outw_p (struct net_device *dev, unsigned short val, int addr, int svflgs) | 
 | { | 
 | 	unsigned long flags; | 
 |  | 
 | 	if (svflgs) | 
 | 		local_irq_save (flags); | 
 |  | 
 | 	writeb(addr >> 12, REG_PAGE); | 
 | 	writew(val, ETHER1_RAM + ((addr & 4095) << 1)); | 
 | 	if (svflgs) | 
 | 		local_irq_restore (flags); | 
 | } | 
 |  | 
 | /* | 
 |  * Some inline assembler to allow fast transfers on to/off of the card. | 
 |  * Since this driver depends on some features presented by the ARM | 
 |  * specific architecture, and that you can't configure this driver | 
 |  * without specifiing ARM mode, this is not a problem. | 
 |  * | 
 |  * This routine is essentially an optimised memcpy from the card's | 
 |  * onboard RAM to kernel memory. | 
 |  */ | 
 | static void | 
 | ether1_writebuffer (struct net_device *dev, void *data, unsigned int start, unsigned int length) | 
 | { | 
 | 	unsigned int page, thislen, offset; | 
 | 	void __iomem *addr; | 
 |  | 
 | 	offset = start & 4095; | 
 | 	page = start >> 12; | 
 | 	addr = ETHER1_RAM + (offset << 1); | 
 |  | 
 | 	if (offset + length > 4096) | 
 | 		thislen = 4096 - offset; | 
 | 	else | 
 | 		thislen = length; | 
 |  | 
 | 	do { | 
 | 		int used; | 
 |  | 
 | 		writeb(page, REG_PAGE); | 
 | 		length -= thislen; | 
 |  | 
 | 		__asm__ __volatile__( | 
 | 	"subs	%3, %3, #2\n\ | 
 | 	bmi	2f\n\ | 
 | 1:	ldr	%0, [%1], #2\n\ | 
 | 	mov	%0, %0, lsl #16\n\ | 
 | 	orr	%0, %0, %0, lsr #16\n\ | 
 | 	str	%0, [%2], #4\n\ | 
 | 	subs	%3, %3, #2\n\ | 
 | 	bmi	2f\n\ | 
 | 	ldr	%0, [%1], #2\n\ | 
 | 	mov	%0, %0, lsl #16\n\ | 
 | 	orr	%0, %0, %0, lsr #16\n\ | 
 | 	str	%0, [%2], #4\n\ | 
 | 	subs	%3, %3, #2\n\ | 
 | 	bmi	2f\n\ | 
 | 	ldr	%0, [%1], #2\n\ | 
 | 	mov	%0, %0, lsl #16\n\ | 
 | 	orr	%0, %0, %0, lsr #16\n\ | 
 | 	str	%0, [%2], #4\n\ | 
 | 	subs	%3, %3, #2\n\ | 
 | 	bmi	2f\n\ | 
 | 	ldr	%0, [%1], #2\n\ | 
 | 	mov	%0, %0, lsl #16\n\ | 
 | 	orr	%0, %0, %0, lsr #16\n\ | 
 | 	str	%0, [%2], #4\n\ | 
 | 	subs	%3, %3, #2\n\ | 
 | 	bpl	1b\n\ | 
 | 2:	adds	%3, %3, #1\n\ | 
 | 	ldreqb	%0, [%1]\n\ | 
 | 	streqb	%0, [%2]" | 
 | 		: "=&r" (used), "=&r" (data) | 
 | 		: "r"  (addr), "r" (thislen), "1" (data)); | 
 |  | 
 | 		addr = ETHER1_RAM; | 
 |  | 
 | 		thislen = length; | 
 | 		if (thislen > 4096) | 
 | 			thislen = 4096; | 
 | 		page++; | 
 | 	} while (thislen); | 
 | } | 
 |  | 
 | static void | 
 | ether1_readbuffer (struct net_device *dev, void *data, unsigned int start, unsigned int length) | 
 | { | 
 | 	unsigned int page, thislen, offset; | 
 | 	void __iomem *addr; | 
 |  | 
 | 	offset = start & 4095; | 
 | 	page = start >> 12; | 
 | 	addr = ETHER1_RAM + (offset << 1); | 
 |  | 
 | 	if (offset + length > 4096) | 
 | 		thislen = 4096 - offset; | 
 | 	else | 
 | 		thislen = length; | 
 |  | 
 | 	do { | 
 | 		int used; | 
 |  | 
 | 		writeb(page, REG_PAGE); | 
 | 		length -= thislen; | 
 |  | 
 | 		__asm__ __volatile__( | 
 | 	"subs	%3, %3, #2\n\ | 
 | 	bmi	2f\n\ | 
 | 1:	ldr	%0, [%2], #4\n\ | 
 | 	strb	%0, [%1], #1\n\ | 
 | 	mov	%0, %0, lsr #8\n\ | 
 | 	strb	%0, [%1], #1\n\ | 
 | 	subs	%3, %3, #2\n\ | 
 | 	bmi	2f\n\ | 
 | 	ldr	%0, [%2], #4\n\ | 
 | 	strb	%0, [%1], #1\n\ | 
 | 	mov	%0, %0, lsr #8\n\ | 
 | 	strb	%0, [%1], #1\n\ | 
 | 	subs	%3, %3, #2\n\ | 
 | 	bmi	2f\n\ | 
 | 	ldr	%0, [%2], #4\n\ | 
 | 	strb	%0, [%1], #1\n\ | 
 | 	mov	%0, %0, lsr #8\n\ | 
 | 	strb	%0, [%1], #1\n\ | 
 | 	subs	%3, %3, #2\n\ | 
 | 	bmi	2f\n\ | 
 | 	ldr	%0, [%2], #4\n\ | 
 | 	strb	%0, [%1], #1\n\ | 
 | 	mov	%0, %0, lsr #8\n\ | 
 | 	strb	%0, [%1], #1\n\ | 
 | 	subs	%3, %3, #2\n\ | 
 | 	bpl	1b\n\ | 
 | 2:	adds	%3, %3, #1\n\ | 
 | 	ldreqb	%0, [%2]\n\ | 
 | 	streqb	%0, [%1]" | 
 | 		: "=&r" (used), "=&r" (data) | 
 | 		: "r"  (addr), "r" (thislen), "1" (data)); | 
 |  | 
 | 		addr = ETHER1_RAM; | 
 |  | 
 | 		thislen = length; | 
 | 		if (thislen > 4096) | 
 | 			thislen = 4096; | 
 | 		page++; | 
 | 	} while (thislen); | 
 | } | 
 |  | 
 | static int | 
 | ether1_ramtest(struct net_device *dev, unsigned char byte) | 
 | { | 
 | 	unsigned char *buffer = kmalloc (BUFFER_SIZE, GFP_KERNEL); | 
 | 	int i, ret = BUFFER_SIZE; | 
 | 	int max_errors = 15; | 
 | 	int bad = -1; | 
 | 	int bad_start = 0; | 
 |  | 
 | 	if (!buffer) | 
 | 		return 1; | 
 |  | 
 | 	memset (buffer, byte, BUFFER_SIZE); | 
 | 	ether1_writebuffer (dev, buffer, 0, BUFFER_SIZE); | 
 | 	memset (buffer, byte ^ 0xff, BUFFER_SIZE); | 
 | 	ether1_readbuffer (dev, buffer, 0, BUFFER_SIZE); | 
 |  | 
 | 	for (i = 0; i < BUFFER_SIZE; i++) { | 
 | 		if (buffer[i] != byte) { | 
 | 			if (max_errors >= 0 && bad != buffer[i]) { | 
 | 				if (bad != -1) | 
 | 					printk ("\n"); | 
 | 				printk (KERN_CRIT "%s: RAM failed with (%02X instead of %02X) at 0x%04X", | 
 | 					dev->name, buffer[i], byte, i); | 
 | 				ret = -ENODEV; | 
 | 				max_errors --; | 
 | 				bad = buffer[i]; | 
 | 				bad_start = i; | 
 | 			} | 
 | 		} else { | 
 | 			if (bad != -1) { | 
 | 			    	if (bad_start == i - 1) | 
 | 					printk ("\n"); | 
 | 				else | 
 | 					printk (" - 0x%04X\n", i - 1); | 
 | 				bad = -1; | 
 | 			} | 
 | 		} | 
 | 	} | 
 |  | 
 | 	if (bad != -1) | 
 | 		printk (" - 0x%04X\n", BUFFER_SIZE); | 
 | 	kfree (buffer); | 
 |  | 
 | 	return ret; | 
 | } | 
 |  | 
 | static int | 
 | ether1_reset (struct net_device *dev) | 
 | { | 
 | 	writeb(CTRL_RST|CTRL_ACK, REG_CONTROL); | 
 | 	return BUS_16; | 
 | } | 
 |  | 
 | static int | 
 | ether1_init_2(struct net_device *dev) | 
 | { | 
 | 	int i; | 
 | 	dev->mem_start = 0; | 
 |  | 
 | 	i = ether1_ramtest (dev, 0x5a); | 
 |  | 
 | 	if (i > 0) | 
 | 		i = ether1_ramtest (dev, 0x1e); | 
 |  | 
 | 	if (i <= 0) | 
 | 	    	return -ENODEV; | 
 |  | 
 | 	dev->mem_end = i; | 
 | 	return 0; | 
 | } | 
 |  | 
 | /* | 
 |  * These are the structures that are loaded into the ether RAM card to | 
 |  * initialise the 82586 | 
 |  */ | 
 |  | 
 | /* at 0x0100 */ | 
 | #define NOP_ADDR	(TX_AREA_START) | 
 | #define NOP_SIZE	(0x06) | 
 | static nop_t  init_nop  = { | 
 | 	0, | 
 | 	CMD_NOP, | 
 | 	NOP_ADDR | 
 | }; | 
 |  | 
 | /* at 0x003a */ | 
 | #define TDR_ADDR	(0x003a) | 
 | #define TDR_SIZE	(0x08) | 
 | static tdr_t  init_tdr	= { | 
 | 	0, | 
 | 	CMD_TDR | CMD_INTR, | 
 | 	NOP_ADDR, | 
 | 	0 | 
 | }; | 
 |  | 
 | /* at 0x002e */ | 
 | #define MC_ADDR		(0x002e) | 
 | #define MC_SIZE		(0x0c) | 
 | static mc_t   init_mc   = { | 
 | 	0, | 
 | 	CMD_SETMULTICAST, | 
 | 	TDR_ADDR, | 
 | 	0, | 
 | 	{ { 0, } } | 
 | }; | 
 |  | 
 | /* at 0x0022 */ | 
 | #define SA_ADDR		(0x0022) | 
 | #define SA_SIZE		(0x0c) | 
 | static sa_t   init_sa   = { | 
 | 	0, | 
 | 	CMD_SETADDRESS, | 
 | 	MC_ADDR, | 
 | 	{ 0, } | 
 | }; | 
 |  | 
 | /* at 0x0010 */ | 
 | #define CFG_ADDR	(0x0010) | 
 | #define CFG_SIZE	(0x12) | 
 | static cfg_t  init_cfg  = { | 
 | 	0, | 
 | 	CMD_CONFIG, | 
 | 	SA_ADDR, | 
 | 	8, | 
 | 	8, | 
 | 	CFG8_SRDY, | 
 | 	CFG9_PREAMB8 | CFG9_ADDRLENBUF | CFG9_ADDRLEN(6), | 
 | 	0, | 
 | 	0x60, | 
 | 	0, | 
 | 	CFG13_RETRY(15) | CFG13_SLOTH(2), | 
 | 	0, | 
 | }; | 
 |  | 
 | /* at 0x0000 */ | 
 | #define SCB_ADDR	(0x0000) | 
 | #define SCB_SIZE	(0x10) | 
 | static scb_t  init_scb  = { | 
 | 	0, | 
 | 	SCB_CMDACKRNR | SCB_CMDACKCNA | SCB_CMDACKFR | SCB_CMDACKCX, | 
 | 	CFG_ADDR, | 
 | 	RX_AREA_START, | 
 | 	0, | 
 | 	0, | 
 | 	0, | 
 | 	0 | 
 | }; | 
 |  | 
 | /* at 0xffee */ | 
 | #define ISCP_ADDR	(0xffee) | 
 | #define ISCP_SIZE	(0x08) | 
 | static iscp_t init_iscp = { | 
 | 	1, | 
 | 	SCB_ADDR, | 
 | 	0x0000, | 
 | 	0x0000 | 
 | }; | 
 |  | 
 | /* at 0xfff6 */ | 
 | #define SCP_ADDR	(0xfff6) | 
 | #define SCP_SIZE	(0x0a) | 
 | static scp_t  init_scp  = { | 
 | 	SCP_SY_16BBUS, | 
 | 	{ 0, 0 }, | 
 | 	ISCP_ADDR, | 
 | 	0 | 
 | }; | 
 |  | 
 | #define RFD_SIZE	(0x16) | 
 | static rfd_t  init_rfd	= { | 
 | 	0, | 
 | 	0, | 
 | 	0, | 
 | 	0, | 
 | 	{ 0, }, | 
 | 	{ 0, }, | 
 | 	0 | 
 | }; | 
 |  | 
 | #define RBD_SIZE	(0x0a) | 
 | static rbd_t  init_rbd	= { | 
 | 	0, | 
 | 	0, | 
 | 	0, | 
 | 	0, | 
 | 	ETH_FRAME_LEN + 8 | 
 | }; | 
 |  | 
 | #define TX_SIZE		(0x08) | 
 | #define TBD_SIZE	(0x08) | 
 |  | 
 | static int | 
 | ether1_init_for_open (struct net_device *dev) | 
 | { | 
 | 	int i, status, addr, next, next2; | 
 | 	int failures = 0; | 
 | 	unsigned long timeout; | 
 |  | 
 | 	writeb(CTRL_RST|CTRL_ACK, REG_CONTROL); | 
 |  | 
 | 	for (i = 0; i < 6; i++) | 
 | 		init_sa.sa_addr[i] = dev->dev_addr[i]; | 
 |  | 
 | 	/* load data structures into ether1 RAM */ | 
 | 	ether1_writebuffer (dev, &init_scp,  SCP_ADDR,  SCP_SIZE); | 
 | 	ether1_writebuffer (dev, &init_iscp, ISCP_ADDR, ISCP_SIZE); | 
 | 	ether1_writebuffer (dev, &init_scb,  SCB_ADDR,  SCB_SIZE); | 
 | 	ether1_writebuffer (dev, &init_cfg,  CFG_ADDR,  CFG_SIZE); | 
 | 	ether1_writebuffer (dev, &init_sa,   SA_ADDR,   SA_SIZE); | 
 | 	ether1_writebuffer (dev, &init_mc,   MC_ADDR,   MC_SIZE); | 
 | 	ether1_writebuffer (dev, &init_tdr,  TDR_ADDR,  TDR_SIZE); | 
 | 	ether1_writebuffer (dev, &init_nop,  NOP_ADDR,  NOP_SIZE); | 
 |  | 
 | 	if (ether1_readw(dev, CFG_ADDR, cfg_t, cfg_command, NORMALIRQS) != CMD_CONFIG) { | 
 | 		printk (KERN_ERR "%s: detected either RAM fault or compiler bug\n", | 
 | 			dev->name); | 
 | 		return 1; | 
 | 	} | 
 |  | 
 | 	/* | 
 | 	 * setup circularly linked list of { rfd, rbd, buffer }, with | 
 | 	 * all rfds circularly linked, rbds circularly linked. | 
 | 	 * First rfd is linked to scp, first rbd is linked to first | 
 | 	 * rfd.  Last rbd has a suspend command. | 
 | 	 */ | 
 | 	addr = RX_AREA_START; | 
 | 	do { | 
 | 		next = addr + RFD_SIZE + RBD_SIZE + ETH_FRAME_LEN + 10; | 
 | 		next2 = next + RFD_SIZE + RBD_SIZE + ETH_FRAME_LEN + 10; | 
 |  | 
 | 		if (next2 >= RX_AREA_END) { | 
 | 			next = RX_AREA_START; | 
 | 			init_rfd.rfd_command = RFD_CMDEL | RFD_CMDSUSPEND; | 
 | 			priv(dev)->rx_tail = addr; | 
 | 		} else | 
 | 			init_rfd.rfd_command = 0; | 
 | 		if (addr == RX_AREA_START) | 
 | 			init_rfd.rfd_rbdoffset = addr + RFD_SIZE; | 
 | 		else | 
 | 			init_rfd.rfd_rbdoffset = 0; | 
 | 		init_rfd.rfd_link = next; | 
 | 		init_rbd.rbd_link = next + RFD_SIZE; | 
 | 		init_rbd.rbd_bufl = addr + RFD_SIZE + RBD_SIZE; | 
 |  | 
 | 		ether1_writebuffer (dev, &init_rfd, addr, RFD_SIZE); | 
 | 		ether1_writebuffer (dev, &init_rbd, addr + RFD_SIZE, RBD_SIZE); | 
 | 		addr = next; | 
 | 	} while (next2 < RX_AREA_END); | 
 |  | 
 | 	priv(dev)->tx_link = NOP_ADDR; | 
 | 	priv(dev)->tx_head = NOP_ADDR + NOP_SIZE; | 
 | 	priv(dev)->tx_tail = TDR_ADDR; | 
 | 	priv(dev)->rx_head = RX_AREA_START; | 
 |  | 
 | 	/* release reset & give 586 a prod */ | 
 | 	priv(dev)->resetting = 1; | 
 | 	priv(dev)->initialising = 1; | 
 | 	writeb(CTRL_RST, REG_CONTROL); | 
 | 	writeb(0, REG_CONTROL); | 
 | 	writeb(CTRL_CA, REG_CONTROL); | 
 |  | 
 | 	/* 586 should now unset iscp.busy */ | 
 | 	timeout = jiffies + HZ/2; | 
 | 	while (ether1_readw(dev, ISCP_ADDR, iscp_t, iscp_busy, DISABLEIRQS) == 1) { | 
 | 		if (time_after(jiffies, timeout)) { | 
 | 			printk (KERN_WARNING "%s: can't initialise 82586: iscp is busy\n", dev->name); | 
 | 			return 1; | 
 | 		} | 
 | 	} | 
 |  | 
 | 	/* check status of commands that we issued */ | 
 | 	timeout += HZ/10; | 
 | 	while (((status = ether1_readw(dev, CFG_ADDR, cfg_t, cfg_status, DISABLEIRQS)) | 
 | 			& STAT_COMPLETE) == 0) { | 
 | 		if (time_after(jiffies, timeout)) | 
 | 			break; | 
 | 	} | 
 |  | 
 | 	if ((status & (STAT_COMPLETE | STAT_OK)) != (STAT_COMPLETE | STAT_OK)) { | 
 | 		printk (KERN_WARNING "%s: can't initialise 82586: config status %04X\n", dev->name, status); | 
 | 		printk (KERN_DEBUG "%s: SCB=[STS=%04X CMD=%04X CBL=%04X RFA=%04X]\n", dev->name, | 
 | 			ether1_readw(dev, SCB_ADDR, scb_t, scb_status, NORMALIRQS), | 
 | 			ether1_readw(dev, SCB_ADDR, scb_t, scb_command, NORMALIRQS), | 
 | 			ether1_readw(dev, SCB_ADDR, scb_t, scb_cbl_offset, NORMALIRQS), | 
 | 			ether1_readw(dev, SCB_ADDR, scb_t, scb_rfa_offset, NORMALIRQS)); | 
 | 		failures += 1; | 
 | 	} | 
 |  | 
 | 	timeout += HZ/10; | 
 | 	while (((status = ether1_readw(dev, SA_ADDR, sa_t, sa_status, DISABLEIRQS)) | 
 | 			& STAT_COMPLETE) == 0) { | 
 | 		if (time_after(jiffies, timeout)) | 
 | 			break; | 
 | 	} | 
 |  | 
 | 	if ((status & (STAT_COMPLETE | STAT_OK)) != (STAT_COMPLETE | STAT_OK)) { | 
 | 		printk (KERN_WARNING "%s: can't initialise 82586: set address status %04X\n", dev->name, status); | 
 | 		printk (KERN_DEBUG "%s: SCB=[STS=%04X CMD=%04X CBL=%04X RFA=%04X]\n", dev->name, | 
 | 			ether1_readw(dev, SCB_ADDR, scb_t, scb_status, NORMALIRQS), | 
 | 			ether1_readw(dev, SCB_ADDR, scb_t, scb_command, NORMALIRQS), | 
 | 			ether1_readw(dev, SCB_ADDR, scb_t, scb_cbl_offset, NORMALIRQS), | 
 | 			ether1_readw(dev, SCB_ADDR, scb_t, scb_rfa_offset, NORMALIRQS)); | 
 | 		failures += 1; | 
 | 	} | 
 |  | 
 | 	timeout += HZ/10; | 
 | 	while (((status = ether1_readw(dev, MC_ADDR, mc_t, mc_status, DISABLEIRQS)) | 
 | 			& STAT_COMPLETE) == 0) { | 
 | 		if (time_after(jiffies, timeout)) | 
 | 			break; | 
 | 	} | 
 |  | 
 | 	if ((status & (STAT_COMPLETE | STAT_OK)) != (STAT_COMPLETE | STAT_OK)) { | 
 | 		printk (KERN_WARNING "%s: can't initialise 82586: set multicast status %04X\n", dev->name, status); | 
 | 		printk (KERN_DEBUG "%s: SCB=[STS=%04X CMD=%04X CBL=%04X RFA=%04X]\n", dev->name, | 
 | 			ether1_readw(dev, SCB_ADDR, scb_t, scb_status, NORMALIRQS), | 
 | 			ether1_readw(dev, SCB_ADDR, scb_t, scb_command, NORMALIRQS), | 
 | 			ether1_readw(dev, SCB_ADDR, scb_t, scb_cbl_offset, NORMALIRQS), | 
 | 			ether1_readw(dev, SCB_ADDR, scb_t, scb_rfa_offset, NORMALIRQS)); | 
 | 		failures += 1; | 
 | 	} | 
 |  | 
 | 	timeout += HZ; | 
 | 	while (((status = ether1_readw(dev, TDR_ADDR, tdr_t, tdr_status, DISABLEIRQS)) | 
 | 			& STAT_COMPLETE) == 0) { | 
 | 		if (time_after(jiffies, timeout)) | 
 | 			break; | 
 | 	} | 
 |  | 
 | 	if ((status & (STAT_COMPLETE | STAT_OK)) != (STAT_COMPLETE | STAT_OK)) { | 
 | 		printk (KERN_WARNING "%s: can't tdr (ignored)\n", dev->name); | 
 | 		printk (KERN_DEBUG "%s: SCB=[STS=%04X CMD=%04X CBL=%04X RFA=%04X]\n", dev->name, | 
 | 			ether1_readw(dev, SCB_ADDR, scb_t, scb_status, NORMALIRQS), | 
 | 			ether1_readw(dev, SCB_ADDR, scb_t, scb_command, NORMALIRQS), | 
 | 			ether1_readw(dev, SCB_ADDR, scb_t, scb_cbl_offset, NORMALIRQS), | 
 | 			ether1_readw(dev, SCB_ADDR, scb_t, scb_rfa_offset, NORMALIRQS)); | 
 | 	} else { | 
 | 		status = ether1_readw(dev, TDR_ADDR, tdr_t, tdr_result, DISABLEIRQS); | 
 | 		if (status & TDR_XCVRPROB) | 
 | 			printk (KERN_WARNING "%s: i/f failed tdr: transceiver problem\n", dev->name); | 
 | 		else if ((status & (TDR_SHORT|TDR_OPEN)) && (status & TDR_TIME)) { | 
 | #ifdef FANCY | 
 | 			printk (KERN_WARNING "%s: i/f failed tdr: cable %s %d.%d us away\n", dev->name, | 
 | 				status & TDR_SHORT ? "short" : "open", (status & TDR_TIME) / 10, | 
 | 				(status & TDR_TIME) % 10); | 
 | #else | 
 | 			printk (KERN_WARNING "%s: i/f failed tdr: cable %s %d clks away\n", dev->name, | 
 | 				status & TDR_SHORT ? "short" : "open", (status & TDR_TIME)); | 
 | #endif | 
 | 		} | 
 | 	} | 
 |  | 
 | 	if (failures) | 
 | 		ether1_reset (dev); | 
 | 	return failures ? 1 : 0; | 
 | } | 
 |  | 
 | /* ------------------------------------------------------------------------- */ | 
 |  | 
 | static int | 
 | ether1_txalloc (struct net_device *dev, int size) | 
 | { | 
 | 	int start, tail; | 
 |  | 
 | 	size = (size + 1) & ~1; | 
 | 	tail = priv(dev)->tx_tail; | 
 |  | 
 | 	if (priv(dev)->tx_head + size > TX_AREA_END) { | 
 | 		if (tail > priv(dev)->tx_head) | 
 | 			return -1; | 
 | 		start = TX_AREA_START; | 
 | 		if (start + size > tail) | 
 | 			return -1; | 
 | 		priv(dev)->tx_head = start + size; | 
 | 	} else { | 
 | 		if (priv(dev)->tx_head < tail && (priv(dev)->tx_head + size) > tail) | 
 | 			return -1; | 
 | 		start = priv(dev)->tx_head; | 
 | 		priv(dev)->tx_head += size; | 
 | 	} | 
 |  | 
 | 	return start; | 
 | } | 
 |  | 
 | static int | 
 | ether1_open (struct net_device *dev) | 
 | { | 
 | 	if (request_irq(dev->irq, ether1_interrupt, 0, "ether1", dev)) | 
 | 		return -EAGAIN; | 
 |  | 
 | 	if (ether1_init_for_open (dev)) { | 
 | 		free_irq (dev->irq, dev); | 
 | 		return -EAGAIN; | 
 | 	} | 
 |  | 
 | 	netif_start_queue(dev); | 
 |  | 
 | 	return 0; | 
 | } | 
 |  | 
 | static void | 
 | ether1_timeout(struct net_device *dev) | 
 | { | 
 | 	printk(KERN_WARNING "%s: transmit timeout, network cable problem?\n", | 
 | 		dev->name); | 
 | 	printk(KERN_WARNING "%s: resetting device\n", dev->name); | 
 |  | 
 | 	ether1_reset (dev); | 
 |  | 
 | 	if (ether1_init_for_open (dev)) | 
 | 		printk (KERN_ERR "%s: unable to restart interface\n", dev->name); | 
 |  | 
 | 	dev->stats.tx_errors++; | 
 | 	netif_wake_queue(dev); | 
 | } | 
 |  | 
 | static int | 
 | ether1_sendpacket (struct sk_buff *skb, struct net_device *dev) | 
 | { | 
 | 	int tmp, tst, nopaddr, txaddr, tbdaddr, dataddr; | 
 | 	unsigned long flags; | 
 | 	tx_t tx; | 
 | 	tbd_t tbd; | 
 | 	nop_t nop; | 
 |  | 
 | 	if (priv(dev)->restart) { | 
 | 		printk(KERN_WARNING "%s: resetting device\n", dev->name); | 
 |  | 
 | 		ether1_reset(dev); | 
 |  | 
 | 		if (ether1_init_for_open(dev)) | 
 | 			printk(KERN_ERR "%s: unable to restart interface\n", dev->name); | 
 | 		else | 
 | 			priv(dev)->restart = 0; | 
 | 	} | 
 |  | 
 | 	if (skb->len < ETH_ZLEN) { | 
 | 		if (skb_padto(skb, ETH_ZLEN)) | 
 | 			goto out; | 
 | 	} | 
 |  | 
 | 	/* | 
 | 	 * insert packet followed by a nop | 
 | 	 */ | 
 | 	txaddr = ether1_txalloc (dev, TX_SIZE); | 
 | 	tbdaddr = ether1_txalloc (dev, TBD_SIZE); | 
 | 	dataddr = ether1_txalloc (dev, skb->len); | 
 | 	nopaddr = ether1_txalloc (dev, NOP_SIZE); | 
 |  | 
 | 	tx.tx_status = 0; | 
 | 	tx.tx_command = CMD_TX | CMD_INTR; | 
 | 	tx.tx_link = nopaddr; | 
 | 	tx.tx_tbdoffset = tbdaddr; | 
 | 	tbd.tbd_opts = TBD_EOL | skb->len; | 
 | 	tbd.tbd_link = I82586_NULL; | 
 | 	tbd.tbd_bufl = dataddr; | 
 | 	tbd.tbd_bufh = 0; | 
 | 	nop.nop_status = 0; | 
 | 	nop.nop_command = CMD_NOP; | 
 | 	nop.nop_link = nopaddr; | 
 |  | 
 | 	local_irq_save(flags); | 
 | 	ether1_writebuffer (dev, &tx, txaddr, TX_SIZE); | 
 | 	ether1_writebuffer (dev, &tbd, tbdaddr, TBD_SIZE); | 
 | 	ether1_writebuffer (dev, skb->data, dataddr, skb->len); | 
 | 	ether1_writebuffer (dev, &nop, nopaddr, NOP_SIZE); | 
 | 	tmp = priv(dev)->tx_link; | 
 | 	priv(dev)->tx_link = nopaddr; | 
 |  | 
 | 	/* now reset the previous nop pointer */ | 
 | 	ether1_writew(dev, txaddr, tmp, nop_t, nop_link, NORMALIRQS); | 
 |  | 
 | 	local_irq_restore(flags); | 
 |  | 
 | 	/* handle transmit */ | 
 |  | 
 | 	/* check to see if we have room for a full sized ether frame */ | 
 | 	tmp = priv(dev)->tx_head; | 
 | 	tst = ether1_txalloc (dev, TX_SIZE + TBD_SIZE + NOP_SIZE + ETH_FRAME_LEN); | 
 | 	priv(dev)->tx_head = tmp; | 
 | 	dev_kfree_skb (skb); | 
 |  | 
 | 	if (tst == -1) | 
 | 		netif_stop_queue(dev); | 
 |  | 
 |  out: | 
 | 	return NETDEV_TX_OK; | 
 | } | 
 |  | 
 | static void | 
 | ether1_xmit_done (struct net_device *dev) | 
 | { | 
 | 	nop_t nop; | 
 | 	int caddr, tst; | 
 |  | 
 | 	caddr = priv(dev)->tx_tail; | 
 |  | 
 | again: | 
 | 	ether1_readbuffer (dev, &nop, caddr, NOP_SIZE); | 
 |  | 
 | 	switch (nop.nop_command & CMD_MASK) { | 
 | 	case CMD_TDR: | 
 | 		/* special case */ | 
 | 		if (ether1_readw(dev, SCB_ADDR, scb_t, scb_cbl_offset, NORMALIRQS) | 
 | 				!= (unsigned short)I82586_NULL) { | 
 | 			ether1_writew(dev, SCB_CMDCUCSTART | SCB_CMDRXSTART, SCB_ADDR, scb_t, | 
 | 				    scb_command, NORMALIRQS); | 
 | 			writeb(CTRL_CA, REG_CONTROL); | 
 | 		} | 
 | 		priv(dev)->tx_tail = NOP_ADDR; | 
 | 		return; | 
 |  | 
 | 	case CMD_NOP: | 
 | 		if (nop.nop_link == caddr) { | 
 | 			if (priv(dev)->initialising == 0) | 
 | 				printk (KERN_WARNING "%s: strange command complete with no tx command!\n", dev->name); | 
 | 			else | 
 | 			        priv(dev)->initialising = 0; | 
 | 			return; | 
 | 		} | 
 | 		if (caddr == nop.nop_link) | 
 | 			return; | 
 | 		caddr = nop.nop_link; | 
 | 		goto again; | 
 |  | 
 | 	case CMD_TX: | 
 | 		if (nop.nop_status & STAT_COMPLETE) | 
 | 			break; | 
 | 		printk (KERN_ERR "%s: strange command complete without completed command\n", dev->name); | 
 | 		priv(dev)->restart = 1; | 
 | 		return; | 
 |  | 
 | 	default: | 
 | 		printk (KERN_WARNING "%s: strange command %d complete! (offset %04X)", dev->name, | 
 | 			nop.nop_command & CMD_MASK, caddr); | 
 | 		priv(dev)->restart = 1; | 
 | 		return; | 
 | 	} | 
 |  | 
 | 	while (nop.nop_status & STAT_COMPLETE) { | 
 | 		if (nop.nop_status & STAT_OK) { | 
 | 			dev->stats.tx_packets++; | 
 | 			dev->stats.collisions += (nop.nop_status & STAT_COLLISIONS); | 
 | 		} else { | 
 | 			dev->stats.tx_errors++; | 
 |  | 
 | 			if (nop.nop_status & STAT_COLLAFTERTX) | 
 | 				dev->stats.collisions++; | 
 | 			if (nop.nop_status & STAT_NOCARRIER) | 
 | 				dev->stats.tx_carrier_errors++; | 
 | 			if (nop.nop_status & STAT_TXLOSTCTS) | 
 | 				printk (KERN_WARNING "%s: cts lost\n", dev->name); | 
 | 			if (nop.nop_status & STAT_TXSLOWDMA) | 
 | 				dev->stats.tx_fifo_errors++; | 
 | 			if (nop.nop_status & STAT_COLLEXCESSIVE) | 
 | 				dev->stats.collisions += 16; | 
 | 		} | 
 |  | 
 | 		if (nop.nop_link == caddr) { | 
 | 			printk (KERN_ERR "%s: tx buffer chaining error: tx command points to itself\n", dev->name); | 
 | 			break; | 
 | 		} | 
 |  | 
 | 		caddr = nop.nop_link; | 
 | 		ether1_readbuffer (dev, &nop, caddr, NOP_SIZE); | 
 | 		if ((nop.nop_command & CMD_MASK) != CMD_NOP) { | 
 | 			printk (KERN_ERR "%s: tx buffer chaining error: no nop after tx command\n", dev->name); | 
 | 			break; | 
 | 		} | 
 |  | 
 | 		if (caddr == nop.nop_link) | 
 | 			break; | 
 |  | 
 | 		caddr = nop.nop_link; | 
 | 		ether1_readbuffer (dev, &nop, caddr, NOP_SIZE); | 
 | 		if ((nop.nop_command & CMD_MASK) != CMD_TX) { | 
 | 			printk (KERN_ERR "%s: tx buffer chaining error: no tx command after nop\n", dev->name); | 
 | 			break; | 
 | 		} | 
 | 	} | 
 | 	priv(dev)->tx_tail = caddr; | 
 |  | 
 | 	caddr = priv(dev)->tx_head; | 
 | 	tst = ether1_txalloc (dev, TX_SIZE + TBD_SIZE + NOP_SIZE + ETH_FRAME_LEN); | 
 | 	priv(dev)->tx_head = caddr; | 
 | 	if (tst != -1) | 
 | 		netif_wake_queue(dev); | 
 | } | 
 |  | 
 | static void | 
 | ether1_recv_done (struct net_device *dev) | 
 | { | 
 | 	int status; | 
 | 	int nexttail, rbdaddr; | 
 | 	rbd_t rbd; | 
 |  | 
 | 	do { | 
 | 		status = ether1_readw(dev, priv(dev)->rx_head, rfd_t, rfd_status, NORMALIRQS); | 
 | 		if ((status & RFD_COMPLETE) == 0) | 
 | 			break; | 
 |  | 
 | 		rbdaddr = ether1_readw(dev, priv(dev)->rx_head, rfd_t, rfd_rbdoffset, NORMALIRQS); | 
 | 		ether1_readbuffer (dev, &rbd, rbdaddr, RBD_SIZE); | 
 |  | 
 | 		if ((rbd.rbd_status & (RBD_EOF | RBD_ACNTVALID)) == (RBD_EOF | RBD_ACNTVALID)) { | 
 | 			int length = rbd.rbd_status & RBD_ACNT; | 
 | 			struct sk_buff *skb; | 
 |  | 
 | 			length = (length + 1) & ~1; | 
 | 			skb = netdev_alloc_skb(dev, length + 2); | 
 |  | 
 | 			if (skb) { | 
 | 				skb_reserve (skb, 2); | 
 |  | 
 | 				ether1_readbuffer (dev, skb_put (skb, length), rbd.rbd_bufl, length); | 
 |  | 
 | 				skb->protocol = eth_type_trans (skb, dev); | 
 | 				netif_rx (skb); | 
 | 				dev->stats.rx_packets++; | 
 | 			} else | 
 | 				dev->stats.rx_dropped++; | 
 | 		} else { | 
 | 			printk(KERN_WARNING "%s: %s\n", dev->name, | 
 | 				(rbd.rbd_status & RBD_EOF) ? "oversized packet" : "acnt not valid"); | 
 | 			dev->stats.rx_dropped++; | 
 | 		} | 
 |  | 
 | 		nexttail = ether1_readw(dev, priv(dev)->rx_tail, rfd_t, rfd_link, NORMALIRQS); | 
 | 		/* nexttail should be rx_head */ | 
 | 		if (nexttail != priv(dev)->rx_head) | 
 | 			printk(KERN_ERR "%s: receiver buffer chaining error (%04X != %04X)\n", | 
 | 				dev->name, nexttail, priv(dev)->rx_head); | 
 | 		ether1_writew(dev, RFD_CMDEL | RFD_CMDSUSPEND, nexttail, rfd_t, rfd_command, NORMALIRQS); | 
 | 		ether1_writew(dev, 0, priv(dev)->rx_tail, rfd_t, rfd_command, NORMALIRQS); | 
 | 		ether1_writew(dev, 0, priv(dev)->rx_tail, rfd_t, rfd_status, NORMALIRQS); | 
 | 		ether1_writew(dev, 0, priv(dev)->rx_tail, rfd_t, rfd_rbdoffset, NORMALIRQS); | 
 | 	 | 
 | 		priv(dev)->rx_tail = nexttail; | 
 | 		priv(dev)->rx_head = ether1_readw(dev, priv(dev)->rx_head, rfd_t, rfd_link, NORMALIRQS); | 
 | 	} while (1); | 
 | } | 
 |  | 
 | static irqreturn_t | 
 | ether1_interrupt (int irq, void *dev_id) | 
 | { | 
 | 	struct net_device *dev = (struct net_device *)dev_id; | 
 | 	int status; | 
 |  | 
 | 	status = ether1_readw(dev, SCB_ADDR, scb_t, scb_status, NORMALIRQS); | 
 |  | 
 | 	if (status) { | 
 | 		ether1_writew(dev, status & (SCB_STRNR | SCB_STCNA | SCB_STFR | SCB_STCX), | 
 | 			    SCB_ADDR, scb_t, scb_command, NORMALIRQS); | 
 | 		writeb(CTRL_CA | CTRL_ACK, REG_CONTROL); | 
 | 		if (status & SCB_STCX) { | 
 | 			ether1_xmit_done (dev); | 
 | 		} | 
 | 		if (status & SCB_STCNA) { | 
 | 			if (priv(dev)->resetting == 0) | 
 | 				printk (KERN_WARNING "%s: CU went not ready ???\n", dev->name); | 
 | 			else | 
 | 				priv(dev)->resetting += 1; | 
 | 			if (ether1_readw(dev, SCB_ADDR, scb_t, scb_cbl_offset, NORMALIRQS) | 
 | 					!= (unsigned short)I82586_NULL) { | 
 | 				ether1_writew(dev, SCB_CMDCUCSTART, SCB_ADDR, scb_t, scb_command, NORMALIRQS); | 
 | 				writeb(CTRL_CA, REG_CONTROL); | 
 | 			} | 
 | 			if (priv(dev)->resetting == 2) | 
 | 				priv(dev)->resetting = 0; | 
 | 		} | 
 | 		if (status & SCB_STFR) { | 
 | 			ether1_recv_done (dev); | 
 | 		} | 
 | 		if (status & SCB_STRNR) { | 
 | 			if (ether1_readw(dev, SCB_ADDR, scb_t, scb_status, NORMALIRQS) & SCB_STRXSUSP) { | 
 | 				printk (KERN_WARNING "%s: RU went not ready: RU suspended\n", dev->name); | 
 | 				ether1_writew(dev, SCB_CMDRXRESUME, SCB_ADDR, scb_t, scb_command, NORMALIRQS); | 
 | 				writeb(CTRL_CA, REG_CONTROL); | 
 | 				dev->stats.rx_dropped++;	/* we suspended due to lack of buffer space */ | 
 | 			} else | 
 | 				printk(KERN_WARNING "%s: RU went not ready: %04X\n", dev->name, | 
 | 					ether1_readw(dev, SCB_ADDR, scb_t, scb_status, NORMALIRQS)); | 
 | 			printk (KERN_WARNING "RU ptr = %04X\n", ether1_readw(dev, SCB_ADDR, scb_t, scb_rfa_offset, | 
 | 						NORMALIRQS)); | 
 | 		} | 
 | 	} else | 
 | 		writeb(CTRL_ACK, REG_CONTROL); | 
 |  | 
 | 	return IRQ_HANDLED; | 
 | } | 
 |  | 
 | static int | 
 | ether1_close (struct net_device *dev) | 
 | { | 
 | 	ether1_reset (dev); | 
 |  | 
 | 	free_irq(dev->irq, dev); | 
 |  | 
 | 	return 0; | 
 | } | 
 |  | 
 | /* | 
 |  * Set or clear the multicast filter for this adaptor. | 
 |  * num_addrs == -1	Promiscuous mode, receive all packets. | 
 |  * num_addrs == 0	Normal mode, clear multicast list. | 
 |  * num_addrs > 0	Multicast mode, receive normal and MC packets, and do | 
 |  *			best-effort filtering. | 
 |  */ | 
 | static void | 
 | ether1_setmulticastlist (struct net_device *dev) | 
 | { | 
 | } | 
 |  | 
 | /* ------------------------------------------------------------------------- */ | 
 |  | 
 | static void ether1_banner(void) | 
 | { | 
 | 	static unsigned int version_printed = 0; | 
 |  | 
 | 	if (net_debug && version_printed++ == 0) | 
 | 		printk(KERN_INFO "%s", version); | 
 | } | 
 |  | 
 | static const struct net_device_ops ether1_netdev_ops = { | 
 | 	.ndo_open		= ether1_open, | 
 | 	.ndo_stop		= ether1_close, | 
 | 	.ndo_start_xmit		= ether1_sendpacket, | 
 | 	.ndo_set_rx_mode	= ether1_setmulticastlist, | 
 | 	.ndo_tx_timeout		= ether1_timeout, | 
 | 	.ndo_validate_addr	= eth_validate_addr, | 
 | 	.ndo_set_mac_address	= eth_mac_addr, | 
 | }; | 
 |  | 
 | static int | 
 | ether1_probe(struct expansion_card *ec, const struct ecard_id *id) | 
 | { | 
 | 	struct net_device *dev; | 
 | 	int i, ret = 0; | 
 |  | 
 | 	ether1_banner(); | 
 |  | 
 | 	ret = ecard_request_resources(ec); | 
 | 	if (ret) | 
 | 		goto out; | 
 |  | 
 | 	dev = alloc_etherdev(sizeof(struct ether1_priv)); | 
 | 	if (!dev) { | 
 | 		ret = -ENOMEM; | 
 | 		goto release; | 
 | 	} | 
 |  | 
 | 	SET_NETDEV_DEV(dev, &ec->dev); | 
 |  | 
 | 	dev->irq = ec->irq; | 
 | 	priv(dev)->base = ecardm_iomap(ec, ECARD_RES_IOCFAST, 0, 0); | 
 | 	if (!priv(dev)->base) { | 
 | 		ret = -ENOMEM; | 
 | 		goto free; | 
 | 	} | 
 |  | 
 | 	if ((priv(dev)->bus_type = ether1_reset(dev)) == 0) { | 
 | 		ret = -ENODEV; | 
 | 		goto free; | 
 | 	} | 
 |  | 
 | 	for (i = 0; i < 6; i++) | 
 | 		dev->dev_addr[i] = readb(IDPROM_ADDRESS + (i << 2)); | 
 |  | 
 | 	if (ether1_init_2(dev)) { | 
 | 		ret = -ENODEV; | 
 | 		goto free; | 
 | 	} | 
 |  | 
 | 	dev->netdev_ops		= ðer1_netdev_ops; | 
 | 	dev->watchdog_timeo	= 5 * HZ / 100; | 
 |  | 
 | 	ret = register_netdev(dev); | 
 | 	if (ret) | 
 | 		goto free; | 
 |  | 
 | 	printk(KERN_INFO "%s: ether1 in slot %d, %pM\n", | 
 | 		dev->name, ec->slot_no, dev->dev_addr); | 
 |      | 
 | 	ecard_set_drvdata(ec, dev); | 
 | 	return 0; | 
 |  | 
 |  free: | 
 | 	free_netdev(dev); | 
 |  release: | 
 | 	ecard_release_resources(ec); | 
 |  out: | 
 | 	return ret; | 
 | } | 
 |  | 
 | static void ether1_remove(struct expansion_card *ec) | 
 | { | 
 | 	struct net_device *dev = ecard_get_drvdata(ec); | 
 |  | 
 | 	ecard_set_drvdata(ec, NULL);	 | 
 |  | 
 | 	unregister_netdev(dev); | 
 | 	free_netdev(dev); | 
 | 	ecard_release_resources(ec); | 
 | } | 
 |  | 
 | static const struct ecard_id ether1_ids[] = { | 
 | 	{ MANU_ACORN, PROD_ACORN_ETHER1 }, | 
 | 	{ 0xffff, 0xffff } | 
 | }; | 
 |  | 
 | static struct ecard_driver ether1_driver = { | 
 | 	.probe		= ether1_probe, | 
 | 	.remove		= ether1_remove, | 
 | 	.id_table	= ether1_ids, | 
 | 	.drv = { | 
 | 		.name	= "ether1", | 
 | 	}, | 
 | }; | 
 |  | 
 | static int __init ether1_init(void) | 
 | { | 
 | 	return ecard_register_driver(ðer1_driver); | 
 | } | 
 |  | 
 | static void __exit ether1_exit(void) | 
 | { | 
 | 	ecard_remove_driver(ðer1_driver); | 
 | } | 
 |  | 
 | module_init(ether1_init); | 
 | module_exit(ether1_exit); | 
 |  | 
 | MODULE_LICENSE("GPL"); |