drivers/i2c/busses/i2c-ixp2000.c

/*
 * drivers/i2c/busses/i2c-ixp2000.c
 *
 * I2C adapter for IXP2000 systems using GPIOs for I2C bus
 *
 * Author: Deepak Saxena <dsaxena@plexity.net>
 * Based on IXDP2400 code by: Naeem M. Afzal <naeem.m.afzal@intel.com>
 * Made generic by: Jeff Daly <jeffrey.daly@intel.com>
 *
 * Copyright (c) 2003-2004 MontaVista Software Inc.
 *
 * This file is licensed under  the terms of the GNU General Public 
 * License version 2. This program is licensed "as is" without any 
 * warranty of any kind, whether express or implied.
 *
 * From Jeff Daly:
 *
 * I2C adapter driver for Intel IXDP2xxx platforms. This should work for any
 * IXP2000 platform if it uses the HW GPIO in the same manner.  Basically, 
 * SDA and SCL GPIOs have external pullups.  Setting the respective GPIO to 
 * an input will make the signal a '1' via the pullup.  Setting them to 
 * outputs will pull them down. 
 *
 * The GPIOs are open drain signals and are used as configuration strap inputs
 * during power-up so there's generally a buffer on the board that needs to be 
 * 'enabled' to drive the GPIOs.
 */

#include <linux/config.h>
#ifdef CONFIG_I2C_DEBUG_BUS
#define DEBUG	1
#endif

#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/device.h>
#include <linux/module.h>
#include <linux/i2c.h>
#include <linux/i2c-algo-bit.h>

#include <asm/hardware.h>	/* Pick up IXP42000-specific bits */

static inline int ixp2000_scl_pin(void *data)
{
	return ((struct ixp2000_i2c_pins*)data)->scl_pin;
}

static inline int ixp2000_sda_pin(void *data)
{
	return ((struct ixp2000_i2c_pins*)data)->sda_pin;
}


static void ixp2000_bit_setscl(void *data, int val)
{
	int i = 5000;

	if (val) {
		gpio_line_config(ixp2000_scl_pin(data), GPIO_IN);
		while(!gpio_line_get(ixp2000_scl_pin(data)) && i--);
	} else {
		gpio_line_config(ixp2000_scl_pin(data), GPIO_OUT);
	}
}

static void ixp2000_bit_setsda(void *data, int val)
{
	if (val) {
		gpio_line_config(ixp2000_sda_pin(data), GPIO_IN);
	} else {
		gpio_line_config(ixp2000_sda_pin(data), GPIO_OUT);
	}
}

static int ixp2000_bit_getscl(void *data)
{
	return gpio_line_get(ixp2000_scl_pin(data));
}

static int ixp2000_bit_getsda(void *data)
{
	return gpio_line_get(ixp2000_sda_pin(data));
}

struct ixp2000_i2c_data {
	struct ixp2000_i2c_pins *gpio_pins;
	struct i2c_adapter adapter;
	struct i2c_algo_bit_data algo_data;
};

static int ixp2000_i2c_remove(struct device *dev)
{
	struct platform_device *plat_dev = to_platform_device(dev);
	struct ixp2000_i2c_data *drv_data = dev_get_drvdata(&plat_dev->dev);

	dev_set_drvdata(&plat_dev->dev, NULL);

	i2c_bit_del_bus(&drv_data->adapter);

	kfree(drv_data);

	return 0;
}

static int ixp2000_i2c_probe(struct device *dev)
{
	int err;
	struct platform_device *plat_dev = to_platform_device(dev);
	struct ixp2000_i2c_pins *gpio = plat_dev->dev.platform_data;
	struct ixp2000_i2c_data *drv_data = 
		kmalloc(sizeof(struct ixp2000_i2c_data), GFP_KERNEL);

	if (!drv_data)
		return -ENOMEM;
	memzero(drv_data, sizeof(*drv_data));
	drv_data->gpio_pins = gpio;

	drv_data->algo_data.data = gpio;
	drv_data->algo_data.setsda = ixp2000_bit_setsda;
	drv_data->algo_data.setscl = ixp2000_bit_setscl;
	drv_data->algo_data.getsda = ixp2000_bit_getsda;
	drv_data->algo_data.getscl = ixp2000_bit_getscl;
	drv_data->algo_data.udelay = 6;
	drv_data->algo_data.mdelay = 6;
	drv_data->algo_data.timeout = 100;

	drv_data->adapter.id = I2C_HW_B_IXP2000,
	drv_data->adapter.algo_data = &drv_data->algo_data,

	drv_data->adapter.dev.parent = &plat_dev->dev;

	gpio_line_config(gpio->sda_pin, GPIO_IN);
	gpio_line_config(gpio->scl_pin, GPIO_IN);
	gpio_line_set(gpio->scl_pin, 0);
	gpio_line_set(gpio->sda_pin, 0);

	if ((err = i2c_bit_add_bus(&drv_data->adapter)) != 0) {
		dev_err(dev, "Could not install, error %d\n", err);
		kfree(drv_data);
		return err;
	} 

	dev_set_drvdata(&plat_dev->dev, drv_data);

	return 0;
}

static struct device_driver ixp2000_i2c_driver = {
	.name		= "IXP2000-I2C",
	.bus		= &platform_bus_type,
	.probe		= ixp2000_i2c_probe,
	.remove		= ixp2000_i2c_remove,
};

static int __init ixp2000_i2c_init(void)
{
	return driver_register(&ixp2000_i2c_driver);
}

static void __exit ixp2000_i2c_exit(void)
{
	driver_unregister(&ixp2000_i2c_driver);
}

module_init(ixp2000_i2c_init);
module_exit(ixp2000_i2c_exit);

MODULE_AUTHOR ("Deepak Saxena <dsaxena@plexity.net>");
MODULE_DESCRIPTION("IXP2000 GPIO-based I2C bus driver");
MODULE_LICENSE("GPL");