| Kernel driver ltc2978 |
| ===================== |
| |
| Supported chips: |
| * Linear Technology LTC2974 |
| Prefix: 'ltc2974' |
| Addresses scanned: - |
| Datasheet: http://www.linear.com/product/ltc2974 |
| * Linear Technology LTC2977 |
| Prefix: 'ltc2977' |
| Addresses scanned: - |
| Datasheet: http://www.linear.com/product/ltc2977 |
| * Linear Technology LTC2978, LTC2978A |
| Prefix: 'ltc2978' |
| Addresses scanned: - |
| Datasheet: http://www.linear.com/product/ltc2978 |
| http://www.linear.com/product/ltc2978a |
| * Linear Technology LTC3880 |
| Prefix: 'ltc3880' |
| Addresses scanned: - |
| Datasheet: http://www.linear.com/product/ltc3880 |
| * Linear Technology LTC3883 |
| Prefix: 'ltc3883' |
| Addresses scanned: - |
| Datasheet: http://www.linear.com/product/ltc3883 |
| |
| Author: Guenter Roeck <linux@roeck-us.net> |
| |
| |
| Description |
| ----------- |
| |
| LTC2974 is a quad digital power supply manager. LTC2978 is an octal power supply |
| monitor. LTC2977 is a pin compatible replacement for LTC2978. LTC3880 is a dual |
| output poly-phase step-down DC/DC controller. LTC3883 is a single phase |
| step-down DC/DC controller. |
| |
| |
| Usage Notes |
| ----------- |
| |
| This driver does not probe for PMBus devices. You will have to instantiate |
| devices explicitly. |
| |
| Example: the following commands will load the driver for an LTC2978 at address |
| 0x60 on I2C bus #1: |
| |
| # modprobe ltc2978 |
| # echo ltc2978 0x60 > /sys/bus/i2c/devices/i2c-1/new_device |
| |
| |
| Sysfs attributes |
| ---------------- |
| |
| in1_label "vin" |
| in1_input Measured input voltage. |
| in1_min Minimum input voltage. |
| in1_max Maximum input voltage. |
| LTC2974, LTC2977, and LTC2978 only. |
| in1_lcrit Critical minimum input voltage. |
| LTC2974, LTC2977, and LTC2978 only. |
| in1_crit Critical maximum input voltage. |
| in1_min_alarm Input voltage low alarm. |
| in1_max_alarm Input voltage high alarm. |
| LTC2974, LTC2977, and LTC2978 only. |
| in1_lcrit_alarm Input voltage critical low alarm. |
| LTC2974, LTC2977, and LTC2978 only. |
| in1_crit_alarm Input voltage critical high alarm. |
| in1_lowest Lowest input voltage. |
| LTC2974, LTC2977, and LTC2978 only. |
| in1_highest Highest input voltage. |
| in1_reset_history Reset input voltage history. |
| |
| in[N]_label "vout[1-8]". |
| LTC2974: N=2-5 |
| LTC2977: N=2-9 |
| LTC2978: N=2-9 |
| LTC3880: N=2-3 |
| LTC3883: N=2 |
| in[N]_input Measured output voltage. |
| in[N]_min Minimum output voltage. |
| in[N]_max Maximum output voltage. |
| in[N]_lcrit Critical minimum output voltage. |
| in[N]_crit Critical maximum output voltage. |
| in[N]_min_alarm Output voltage low alarm. |
| in[N]_max_alarm Output voltage high alarm. |
| in[N]_lcrit_alarm Output voltage critical low alarm. |
| in[N]_crit_alarm Output voltage critical high alarm. |
| in[N]_lowest Lowest output voltage. LTC2974 and LTC2978 only. |
| in[N]_highest Highest output voltage. |
| in[N]_reset_history Reset output voltage history. |
| |
| temp[N]_input Measured temperature. |
| On LTC2974, temp[1-4] report external temperatures, |
| and temp5 reports the chip temperature. |
| On LTC2977 and LTC2978, only one temperature measurement |
| is supported and reports the chip temperature. |
| On LTC3880, temp1 and temp2 report external |
| temperatures, and temp3 reports the chip temperature. |
| On LTC3883, temp1 reports an external temperature, |
| and temp2 reports the chip temperature. |
| temp[N]_min Mimimum temperature. LTC2974, LCT2977, and LTC2978 only. |
| temp[N]_max Maximum temperature. |
| temp[N]_lcrit Critical low temperature. |
| temp[N]_crit Critical high temperature. |
| temp[N]_min_alarm Temperature low alarm. |
| LTC2974, LTC2977, and LTC2978 only. |
| temp[N]_max_alarm Temperature high alarm. |
| temp[N]_lcrit_alarm Temperature critical low alarm. |
| temp[N]_crit_alarm Temperature critical high alarm. |
| temp[N]_lowest Lowest measured temperature. |
| LTC2974, LTC2977, and LTC2978 only. |
| Not supported for chip temperature sensor on LTC2974. |
| temp[N]_highest Highest measured temperature. Not supported for chip |
| temperature sensor on LTC2974. |
| temp[N]_reset_history Reset temperature history. Not supported for chip |
| temperature sensor on LTC2974. |
| |
| power1_label "pin". LTC3883 only. |
| power1_input Measured input power. |
| |
| power[N]_label "pout[1-4]". |
| LTC2974: N=1-4 |
| LTC2977: Not supported |
| LTC2978: Not supported |
| LTC3880: N=1-2 |
| LTC3883: N=2 |
| power[N]_input Measured output power. |
| |
| curr1_label "iin". LTC3880 and LTC3883 only. |
| curr1_input Measured input current. |
| curr1_max Maximum input current. |
| curr1_max_alarm Input current high alarm. |
| curr1_highest Highest input current. LTC3883 only. |
| curr1_reset_history Reset input current history. LTC3883 only. |
| |
| curr[N]_label "iout[1-4]". |
| LTC2974: N=1-4 |
| LTC2977: not supported |
| LTC2978: not supported |
| LTC3880: N=2-3 |
| LTC3883: N=2 |
| curr[N]_input Measured output current. |
| curr[N]_max Maximum output current. |
| curr[N]_crit Critical high output current. |
| curr[N]_lcrit Critical low output current. LTC2974 only. |
| curr[N]_max_alarm Output current high alarm. |
| curr[N]_crit_alarm Output current critical high alarm. |
| curr[N]_lcrit_alarm Output current critical low alarm. LTC2974 only. |
| curr[N]_lowest Lowest output current. LTC2974 only. |
| curr[N]_highest Highest output current. |
| curr[N]_reset_history Reset output current history. |