drivers/ide/pci/sl82c105.c - kernel/msm-5.4 - Gitiles

 /*
  * linux/drivers/ide/pci/sl82c105.c
  *
  * SL82C105/Winbond 553 IDE driver
  *
  * Maintainer unknown.
  *
  * Drive tuning added from Rebel.com's kernel sources
  *  -- Russell King (15/11/98) linux@arm.linux.org.uk
  *
  * Merge in Russell's HW workarounds, fix various problems
  * with the timing registers setup.
  *  -- Benjamin Herrenschmidt (01/11/03) benh@kernel.crashing.org
  *
  * Copyright (C) 2006-2007 MontaVista Software, Inc. <source@mvista.com>
  */

 #include <linux/types.h>
 #include <linux/module.h>
 #include <linux/kernel.h>
 #include <linux/timer.h>
 #include <linux/mm.h>
 #include <linux/ioport.h>
 #include <linux/interrupt.h>
 #include <linux/blkdev.h>
 #include <linux/hdreg.h>
 #include <linux/pci.h>
 #include <linux/ide.h>

 #include <asm/io.h>
 #include <asm/dma.h>

 #undef DEBUG

 #ifdef DEBUG
 #define DBG(arg) printk arg
 #else
 #define DBG(fmt,...)
 #endif
 /*
  * SL82C105 PCI config register 0x40 bits.
  */
 #define CTRL_IDE_IRQB   (1 << 30)
 #define CTRL_IDE_IRQA   (1 << 28)
 #define CTRL_LEGIRQ     (1 << 11)
 #define CTRL_P1F16      (1 << 5)
 #define CTRL_P1EN       (1 << 4)
 #define CTRL_P0F16      (1 << 1)
 #define CTRL_P0EN       (1 << 0)

 /*
  * Convert a PIO mode and cycle time to the required on/off times
  * for the interface.  This has protection against runaway timings.
  */
 static unsigned int get_pio_timings(ide_pio_data_t *p)
 {
 	unsigned int cmd_on, cmd_off;

 	cmd_on  = (ide_pio_timings[p->pio_mode].active_time + 29) / 30;
 	cmd_off = (p->cycle_time - 30 * cmd_on + 29) / 30;

 	if (cmd_on == 0)
 		cmd_on = 1;

 	if (cmd_off == 0)
 		cmd_off = 1;

 	return (cmd_on - 1) << 8 | (cmd_off - 1) | (p->use_iordy ? 0x40 : 0x00);
 }

 /*
  * Configure the chipset for PIO mode.
  */
 static u8 sl82c105_tune_pio(ide_drive_t *drive, u8 pio)
 {
 	struct pci_dev *dev	= HWIF(drive)->pci_dev;
 	int reg			= 0x44 + drive->dn * 4;
 	ide_pio_data_t p;
 	u16 drv_ctrl;

 	DBG(("sl82c105_tune_pio(drive:%s, pio:%u)\n", drive->name, pio));

 	pio = ide_get_best_pio_mode(drive, pio, 5, &p);

 	drive->drive_data = drv_ctrl = get_pio_timings(&p);

 	if (!drive->using_dma) {
 		/*
 		 * If we are actually using MW DMA, then we can not
 		 * reprogram the interface drive control register.
 		 */
 		pci_write_config_word(dev, reg,  drv_ctrl);
 		pci_read_config_word (dev, reg, &drv_ctrl);
 	}

 	printk(KERN_DEBUG "%s: selected %s (%dns) (%04X)\n", drive->name,
 	       ide_xfer_verbose(pio + XFER_PIO_0), p.cycle_time, drv_ctrl);

 	return pio;
 }

 /*
  * Configure the drive and the chipset for DMA
  */
 static int config_for_dma (ide_drive_t *drive)
 {
 	ide_hwif_t *hwif = HWIF(drive);
 	struct pci_dev *dev = hwif->pci_dev;
 	unsigned int reg;

 	DBG(("config_for_dma(drive:%s)\n", drive->name));

 	reg = (hwif->channel ? 0x4c : 0x44) + (drive->select.b.unit ? 4 : 0);

 	if (ide_config_drive_speed(drive, XFER_MW_DMA_2) != 0)
 		return 1;

 	pci_write_config_word(dev, reg, 0x0240);

 	return 0;
 }

 /*
  * Check to see if the drive and
  * chipset is capable of DMA mode
  */

 static int sl82c105_check_drive (ide_drive_t *drive)
 {
 	ide_hwif_t *hwif	= HWIF(drive);

 	DBG(("sl82c105_check_drive(drive:%s)\n", drive->name));

 	do {
 		struct hd_driveid *id = drive->id;

 		if (!drive->autodma)
 			break;

 		if (!id || !(id->capability & 1))
 			break;

 		/* Consult the list of known "bad" drives */
 		if (__ide_dma_bad_drive(drive))
 			break;

 		if (id->field_valid & 2) {
 			if ((id->dma_mword & hwif->mwdma_mask) ||
 			    (id->dma_1word & hwif->swdma_mask))
 				return 0;
 		}

 		if (__ide_dma_good_drive(drive) && id->eide_dma_time < 150)
 			return 0;
 	} while (0);

 	return -1;
 }

 /*
  * The SL82C105 holds off all IDE interrupts while in DMA mode until
  * all DMA activity is completed.  Sometimes this causes problems (eg,
  * when the drive wants to report an error condition).
  *
  * 0x7e is a "chip testing" register.  Bit 2 resets the DMA controller
  * state machine.  We need to kick this to work around various bugs.
  */
 static inline void sl82c105_reset_host(struct pci_dev *dev)
 {
 	u16 val;

 	pci_read_config_word(dev, 0x7e, &val);
 	pci_write_config_word(dev, 0x7e, val | (1 << 2));
 	pci_write_config_word(dev, 0x7e, val & ~(1 << 2));
 }

 /*
  * If we get an IRQ timeout, it might be that the DMA state machine
  * got confused.  Fix from Todd Inglett.  Details from Winbond.
  *
  * This function is called when the IDE timer expires, the drive
  * indicates that it is READY, and we were waiting for DMA to complete.
  */
 static int sl82c105_ide_dma_lost_irq(ide_drive_t *drive)
 {
 	ide_hwif_t *hwif = HWIF(drive);
 	struct pci_dev *dev = hwif->pci_dev;
 	u32 val, mask = hwif->channel ? CTRL_IDE_IRQB : CTRL_IDE_IRQA;
 	unsigned long dma_base = hwif->dma_base;

 	printk("sl82c105: lost IRQ: resetting host\n");

 	/*
 	 * Check the raw interrupt from the drive.
 	 */
 	pci_read_config_dword(dev, 0x40, &val);
 	if (val & mask)
 		printk("sl82c105: drive was requesting IRQ, but host lost it\n");

 	/*
 	 * Was DMA enabled?  If so, disable it - we're resetting the
 	 * host.  The IDE layer will be handling the drive for us.
 	 */
 	val = inb(dma_base);
 	if (val & 1) {
 		outb(val & ~1, dma_base);
 		printk("sl82c105: DMA was enabled\n");
 	}

 	sl82c105_reset_host(dev);

 	/* ide_dmaproc would return 1, so we do as well */
 	return 1;
 }

 /*
  * ATAPI devices can cause the SL82C105 DMA state machine to go gaga.
  * Winbond recommend that the DMA state machine is reset prior to
  * setting the bus master DMA enable bit.
  *
  * The generic IDE core will have disabled the BMEN bit before this
  * function is called.
  */
 static void sl82c105_ide_dma_start(ide_drive_t *drive)
 {
 	ide_hwif_t *hwif = HWIF(drive);
 	struct pci_dev *dev = hwif->pci_dev;

 	sl82c105_reset_host(dev);
 	ide_dma_start(drive);
 }

 static int sl82c105_ide_dma_timeout(ide_drive_t *drive)
 {
 	ide_hwif_t *hwif = HWIF(drive);
 	struct pci_dev *dev = hwif->pci_dev;

 	DBG(("sl82c105_ide_dma_timeout(drive:%s)\n", drive->name));

 	sl82c105_reset_host(dev);
 	return __ide_dma_timeout(drive);
 }

 static int sl82c105_ide_dma_on (ide_drive_t *drive)
 {
 	DBG(("sl82c105_ide_dma_on(drive:%s)\n", drive->name));

 	if (config_for_dma(drive))
 		return 1;
 	printk(KERN_INFO "%s: DMA enabled\n", drive->name);
 	return __ide_dma_on(drive);
 }

 static void sl82c105_dma_off_quietly(ide_drive_t *drive)
 {
 	struct pci_dev *dev	= HWIF(drive)->pci_dev;
 	int reg 		= 0x44 + drive->dn * 4;

 	DBG(("sl82c105_dma_off_quietly(drive:%s)\n", drive->name));

 	pci_write_config_word(dev, reg, drive->drive_data);

 	ide_dma_off_quietly(drive);
 }

 /*
  * Ok, that is nasty, but we must make sure the DMA timings
  * won't be used for a PIO access. The solution here is
  * to make sure the 16 bits mode is diabled on the channel
  * when DMA is enabled, thus causing the chip to use PIO0
  * timings for those operations.
  */
 static void sl82c105_selectproc(ide_drive_t *drive)
 {
 	ide_hwif_t *hwif = HWIF(drive);
 	struct pci_dev *dev = hwif->pci_dev;
 	u32 val, old, mask;

 	//DBG(("sl82c105_selectproc(drive:%s)\n", drive->name));

 	mask = hwif->channel ? CTRL_P1F16 : CTRL_P0F16;
 	old = val = (u32)pci_get_drvdata(dev);
 	if (drive->using_dma)
 		val &= ~mask;
 	else
 		val |= mask;
 	if (old != val) {
 		pci_write_config_dword(dev, 0x40, val);
 		pci_set_drvdata(dev, (void *)val);
 	}
 }

 /*
  * ATA reset will clear the 16 bits mode in the control
  * register, we need to update our cache
  */
 static void sl82c105_resetproc(ide_drive_t *drive)
 {
 	struct pci_dev *dev = HWIF(drive)->pci_dev;
 	u32 val;

 	DBG(("sl82c105_resetproc(drive:%s)\n", drive->name));

 	pci_read_config_dword(dev, 0x40, &val);
 	pci_set_drvdata(dev, (void *)val);
 }

 /*
  * We only deal with PIO mode here - DMA mode 'using_dma' is not
  * initialised at the point that this function is called.
  */
 static void sl82c105_tune_drive(ide_drive_t *drive, u8 pio)
 {
 	DBG(("sl82c105_tune_drive(drive:%s, pio:%u)\n", drive->name, pio));

 	pio = sl82c105_tune_pio(drive, pio);
 	(void) ide_config_drive_speed(drive, XFER_PIO_0 + pio);
 }

 /*
  * Return the revision of the Winbond bridge
  * which this function is part of.
  */
 static unsigned int sl82c105_bridge_revision(struct pci_dev *dev)
 {
 	struct pci_dev *bridge;
 	u8 rev;

 	/*
 	 * The bridge should be part of the same device, but function 0.
 	 */
 	bridge = pci_find_slot(dev->bus->number,
 			       PCI_DEVFN(PCI_SLOT(dev->devfn), 0));
 	if (!bridge)
 		return -1;

 	/*
 	 * Make sure it is a Winbond 553 and is an ISA bridge.
 	 */
 	if (bridge->vendor != PCI_VENDOR_ID_WINBOND ||
 	    bridge->device != PCI_DEVICE_ID_WINBOND_83C553 ||
 	    bridge->class >> 8 != PCI_CLASS_BRIDGE_ISA)
 		return -1;

 	/*
 	 * We need to find function 0's revision, not function 1
 	 */
 	pci_read_config_byte(bridge, PCI_REVISION_ID, &rev);

 	return rev;
 }

 /*
  * Enable the PCI device
  *
  * --BenH: It's arch fixup code that should enable channels that
  * have not been enabled by firmware. I decided we can still enable
  * channel 0 here at least, but channel 1 has to be enabled by
  * firmware or arch code. We still set both to 16 bits mode.
  */
 static unsigned int __devinit init_chipset_sl82c105(struct pci_dev *dev, const char *msg)
 {
 	u32 val;

 	DBG(("init_chipset_sl82c105()\n"));

 	pci_read_config_dword(dev, 0x40, &val);
 	val |= CTRL_P0EN | CTRL_P0F16 | CTRL_P1F16;
 	pci_write_config_dword(dev, 0x40, val);
 	pci_set_drvdata(dev, (void *)val);

 	return dev->irq;
 }

 /*
  * Initialise the chip
  */
 static void __devinit init_hwif_sl82c105(ide_hwif_t *hwif)
 {
 	unsigned int rev;

 	DBG(("init_hwif_sl82c105(hwif: ide%d)\n", hwif->index));

 	hwif->tuneproc		= &sl82c105_tune_drive;
 	hwif->selectproc	= &sl82c105_selectproc;
 	hwif->resetproc 	= &sl82c105_resetproc;

 	/*
 	 * We support 32-bit I/O on this interface, and
 	 * it doesn't have problems with interrupts.
 	 */
 	hwif->drives[0].io_32bit = hwif->drives[1].io_32bit = 1;
 	hwif->drives[0].unmask   = hwif->drives[1].unmask   = 1;

 	/*
 	 * We always autotune PIO,  this is done before DMA is checked,
 	 * so there's no risk of accidentally disabling DMA
 	 */
 	hwif->drives[0].autotune = hwif->drives[1].autotune = 1;

 	hwif->atapi_dma = 0;
 	hwif->mwdma_mask = 0;
 	hwif->swdma_mask = 0;
 	hwif->autodma = 0;

 	if (!hwif->dma_base)
 		return;

 	rev = sl82c105_bridge_revision(hwif->pci_dev);
 	if (rev <= 5) {
 		/*
 		 * Never ever EVER under any circumstances enable
 		 * DMA when the bridge is this old.
 		 */
 		printk("    %s: Winbond 553 bridge revision %d, BM-DMA disabled\n",
 		       hwif->name, rev);
 	} else {
 		hwif->atapi_dma = 1;
 		hwif->mwdma_mask = 0x04;

 		hwif->ide_dma_check = &sl82c105_check_drive;
 		hwif->ide_dma_on = &sl82c105_ide_dma_on;
 		hwif->dma_off_quietly = &sl82c105_dma_off_quietly;
 		hwif->ide_dma_lostirq = &sl82c105_ide_dma_lost_irq;
 		hwif->dma_start = &sl82c105_ide_dma_start;
 		hwif->ide_dma_timeout = &sl82c105_ide_dma_timeout;

 		if (!noautodma)
 			hwif->autodma = 1;
 		hwif->drives[0].autodma = hwif->autodma;
 		hwif->drives[1].autodma = hwif->autodma;

 		if (hwif->mate)
 			hwif->serialized = hwif->mate->serialized = 1;
 	}
 }

 static ide_pci_device_t sl82c105_chipset __devinitdata = {
 	.name		= "W82C105",
 	.init_chipset	= init_chipset_sl82c105,
 	.init_hwif	= init_hwif_sl82c105,
 	.channels	= 2,
 	.autodma	= NOAUTODMA,
 	.enablebits	= {{0x40,0x01,0x01}, {0x40,0x10,0x10}},
 	.bootable	= ON_BOARD,
 };

 static int __devinit sl82c105_init_one(struct pci_dev *dev, const struct pci_device_id *id)
 {
 	return ide_setup_pci_device(dev, &sl82c105_chipset);
 }

 static struct pci_device_id sl82c105_pci_tbl[] = {
 	{ PCI_DEVICE(PCI_VENDOR_ID_WINBOND, PCI_DEVICE_ID_WINBOND_82C105), 0},
 	{ 0, },
 };
 MODULE_DEVICE_TABLE(pci, sl82c105_pci_tbl);

 static struct pci_driver driver = {
 	.name		= "W82C105_IDE",
 	.id_table	= sl82c105_pci_tbl,
 	.probe		= sl82c105_init_one,
 };

 static int __init sl82c105_ide_init(void)
 {
 	return ide_pci_register_driver(&driver);
 }

 module_init(sl82c105_ide_init);

 MODULE_DESCRIPTION("PCI driver module for W82C105 IDE");
 MODULE_LICENSE("GPL");
	/*
	* linux/drivers/ide/pci/sl82c105.c
	*
	* SL82C105/Winbond 553 IDE driver
	*
	* Maintainer unknown.
	*
	* Drive tuning added from Rebel.com's kernel sources
	* -- Russell King (15/11/98) linux@arm.linux.org.uk
	*
	* Merge in Russell's HW workarounds, fix various problems
	* with the timing registers setup.
	* -- Benjamin Herrenschmidt (01/11/03) benh@kernel.crashing.org
	*
	* Copyright (C) 2006-2007 MontaVista Software, Inc. <source@mvista.com>
	*/

	#include <linux/types.h>
	#include <linux/module.h>
	#include <linux/kernel.h>
	#include <linux/timer.h>
	#include <linux/mm.h>
	#include <linux/ioport.h>
	#include <linux/interrupt.h>
	#include <linux/blkdev.h>
	#include <linux/hdreg.h>
	#include <linux/pci.h>
	#include <linux/ide.h>

	#include <asm/io.h>
	#include <asm/dma.h>

	#undef DEBUG

	#ifdef DEBUG
	#define DBG(arg) printk arg
	#else
	#define DBG(fmt,...)
	#endif
	/*
	* SL82C105 PCI config register 0x40 bits.
	*/
	#define CTRL_IDE_IRQB (1 << 30)
	#define CTRL_IDE_IRQA (1 << 28)
	#define CTRL_LEGIRQ (1 << 11)
	#define CTRL_P1F16 (1 << 5)
	#define CTRL_P1EN (1 << 4)
	#define CTRL_P0F16 (1 << 1)
	#define CTRL_P0EN (1 << 0)

	/*
	* Convert a PIO mode and cycle time to the required on/off times
	* for the interface. This has protection against runaway timings.
	*/
	static unsigned int get_pio_timings(ide_pio_data_t *p)
	{
	unsigned int cmd_on, cmd_off;

	cmd_on = (ide_pio_timings[p->pio_mode].active_time + 29) / 30;
	cmd_off = (p->cycle_time - 30 * cmd_on + 29) / 30;

	if (cmd_on == 0)
	cmd_on = 1;

	if (cmd_off == 0)
	cmd_off = 1;

	return (cmd_on - 1) << 8 \| (cmd_off - 1) \| (p->use_iordy ? 0x40 : 0x00);
	}

	/*
	* Configure the chipset for PIO mode.
	*/
	static u8 sl82c105_tune_pio(ide_drive_t *drive, u8 pio)
	{
	struct pci_dev *dev = HWIF(drive)->pci_dev;
	int reg = 0x44 + drive->dn * 4;
	ide_pio_data_t p;
	u16 drv_ctrl;

	DBG(("sl82c105_tune_pio(drive:%s, pio:%u)\n", drive->name, pio));

	pio = ide_get_best_pio_mode(drive, pio, 5, &p);

	drive->drive_data = drv_ctrl = get_pio_timings(&p);

	if (!drive->using_dma) {
	/*
	* If we are actually using MW DMA, then we can not
	* reprogram the interface drive control register.
	*/
	pci_write_config_word(dev, reg, drv_ctrl);
	pci_read_config_word (dev, reg, &drv_ctrl);
	}

	printk(KERN_DEBUG "%s: selected %s (%dns) (%04X)\n", drive->name,
	ide_xfer_verbose(pio + XFER_PIO_0), p.cycle_time, drv_ctrl);

	return pio;
	}

	/*
	* Configure the drive and the chipset for DMA
	*/
	static int config_for_dma (ide_drive_t *drive)
	{
	ide_hwif_t *hwif = HWIF(drive);
	struct pci_dev *dev = hwif->pci_dev;
	unsigned int reg;

	DBG(("config_for_dma(drive:%s)\n", drive->name));

	reg = (hwif->channel ? 0x4c : 0x44) + (drive->select.b.unit ? 4 : 0);

	if (ide_config_drive_speed(drive, XFER_MW_DMA_2) != 0)
	return 1;

	pci_write_config_word(dev, reg, 0x0240);

	return 0;
	}

	/*
	* Check to see if the drive and
	* chipset is capable of DMA mode
	*/

	static int sl82c105_check_drive (ide_drive_t *drive)
	{
	ide_hwif_t *hwif = HWIF(drive);

	DBG(("sl82c105_check_drive(drive:%s)\n", drive->name));

	do {
	struct hd_driveid *id = drive->id;

	if (!drive->autodma)
	break;

	if (!id \|\| !(id->capability & 1))
	break;

	/* Consult the list of known "bad" drives */
	if (__ide_dma_bad_drive(drive))
	break;

	if (id->field_valid & 2) {
	if ((id->dma_mword & hwif->mwdma_mask) \|\|
	(id->dma_1word & hwif->swdma_mask))
	return 0;
	}

	if (__ide_dma_good_drive(drive) && id->eide_dma_time < 150)
	return 0;
	} while (0);

	return -1;
	}

	/*
	* The SL82C105 holds off all IDE interrupts while in DMA mode until
	* all DMA activity is completed. Sometimes this causes problems (eg,
	* when the drive wants to report an error condition).
	*
	* 0x7e is a "chip testing" register. Bit 2 resets the DMA controller
	* state machine. We need to kick this to work around various bugs.
	*/
	static inline void sl82c105_reset_host(struct pci_dev *dev)
	{
	u16 val;

	pci_read_config_word(dev, 0x7e, &val);
	pci_write_config_word(dev, 0x7e, val \| (1 << 2));
	pci_write_config_word(dev, 0x7e, val & ~(1 << 2));
	}

	/*
	* If we get an IRQ timeout, it might be that the DMA state machine
	* got confused. Fix from Todd Inglett. Details from Winbond.
	*
	* This function is called when the IDE timer expires, the drive
	* indicates that it is READY, and we were waiting for DMA to complete.
	*/
	static int sl82c105_ide_dma_lost_irq(ide_drive_t *drive)
	{
	ide_hwif_t *hwif = HWIF(drive);
	struct pci_dev *dev = hwif->pci_dev;
	u32 val, mask = hwif->channel ? CTRL_IDE_IRQB : CTRL_IDE_IRQA;
	unsigned long dma_base = hwif->dma_base;

	printk("sl82c105: lost IRQ: resetting host\n");

	/*
	* Check the raw interrupt from the drive.
	*/
	pci_read_config_dword(dev, 0x40, &val);
	if (val & mask)
	printk("sl82c105: drive was requesting IRQ, but host lost it\n");

	/*
	* Was DMA enabled? If so, disable it - we're resetting the
	* host. The IDE layer will be handling the drive for us.
	*/
	val = inb(dma_base);
	if (val & 1) {
	outb(val & ~1, dma_base);
	printk("sl82c105: DMA was enabled\n");
	}

	sl82c105_reset_host(dev);

	/* ide_dmaproc would return 1, so we do as well */
	return 1;
	}

	/*
	* ATAPI devices can cause the SL82C105 DMA state machine to go gaga.
	* Winbond recommend that the DMA state machine is reset prior to
	* setting the bus master DMA enable bit.
	*
	* The generic IDE core will have disabled the BMEN bit before this
	* function is called.
	*/
	static void sl82c105_ide_dma_start(ide_drive_t *drive)
	{
	ide_hwif_t *hwif = HWIF(drive);
	struct pci_dev *dev = hwif->pci_dev;

	sl82c105_reset_host(dev);
	ide_dma_start(drive);
	}

	static int sl82c105_ide_dma_timeout(ide_drive_t *drive)
	{
	ide_hwif_t *hwif = HWIF(drive);
	struct pci_dev *dev = hwif->pci_dev;

	DBG(("sl82c105_ide_dma_timeout(drive:%s)\n", drive->name));

	sl82c105_reset_host(dev);
	return __ide_dma_timeout(drive);
	}

	static int sl82c105_ide_dma_on (ide_drive_t *drive)
	{
	DBG(("sl82c105_ide_dma_on(drive:%s)\n", drive->name));

	if (config_for_dma(drive))
	return 1;
	printk(KERN_INFO "%s: DMA enabled\n", drive->name);
	return __ide_dma_on(drive);
	}

	static void sl82c105_dma_off_quietly(ide_drive_t *drive)
	{
	struct pci_dev *dev = HWIF(drive)->pci_dev;
	int reg = 0x44 + drive->dn * 4;

	DBG(("sl82c105_dma_off_quietly(drive:%s)\n", drive->name));

	pci_write_config_word(dev, reg, drive->drive_data);

	ide_dma_off_quietly(drive);
	}

	/*
	* Ok, that is nasty, but we must make sure the DMA timings
	* won't be used for a PIO access. The solution here is
	* to make sure the 16 bits mode is diabled on the channel
	* when DMA is enabled, thus causing the chip to use PIO0
	* timings for those operations.
	*/
	static void sl82c105_selectproc(ide_drive_t *drive)
	{
	ide_hwif_t *hwif = HWIF(drive);
	struct pci_dev *dev = hwif->pci_dev;
	u32 val, old, mask;

	//DBG(("sl82c105_selectproc(drive:%s)\n", drive->name));

	mask = hwif->channel ? CTRL_P1F16 : CTRL_P0F16;
	old = val = (u32)pci_get_drvdata(dev);
	if (drive->using_dma)
	val &= ~mask;
	else
	val \|= mask;
	if (old != val) {
	pci_write_config_dword(dev, 0x40, val);
	pci_set_drvdata(dev, (void *)val);
	}
	}

	/*
	* ATA reset will clear the 16 bits mode in the control
	* register, we need to update our cache
	*/
	static void sl82c105_resetproc(ide_drive_t *drive)
	{
	struct pci_dev *dev = HWIF(drive)->pci_dev;
	u32 val;

	DBG(("sl82c105_resetproc(drive:%s)\n", drive->name));

	pci_read_config_dword(dev, 0x40, &val);
	pci_set_drvdata(dev, (void *)val);
	}

	/*
	* We only deal with PIO mode here - DMA mode 'using_dma' is not
	* initialised at the point that this function is called.
	*/
	static void sl82c105_tune_drive(ide_drive_t *drive, u8 pio)
	{
	DBG(("sl82c105_tune_drive(drive:%s, pio:%u)\n", drive->name, pio));

	pio = sl82c105_tune_pio(drive, pio);
	(void) ide_config_drive_speed(drive, XFER_PIO_0 + pio);
	}

	/*
	* Return the revision of the Winbond bridge
	* which this function is part of.
	*/
	static unsigned int sl82c105_bridge_revision(struct pci_dev *dev)
	{
	struct pci_dev *bridge;
	u8 rev;

	/*
	* The bridge should be part of the same device, but function 0.
	*/
	bridge = pci_find_slot(dev->bus->number,
	PCI_DEVFN(PCI_SLOT(dev->devfn), 0));
	if (!bridge)
	return -1;

	/*
	* Make sure it is a Winbond 553 and is an ISA bridge.
	*/
	if (bridge->vendor != PCI_VENDOR_ID_WINBOND \|\|
	bridge->device != PCI_DEVICE_ID_WINBOND_83C553 \|\|
	bridge->class >> 8 != PCI_CLASS_BRIDGE_ISA)
	return -1;

	/*
	* We need to find function 0's revision, not function 1
	*/
	pci_read_config_byte(bridge, PCI_REVISION_ID, &rev);

	return rev;
	}

	/*
	* Enable the PCI device
	*
	* --BenH: It's arch fixup code that should enable channels that
	* have not been enabled by firmware. I decided we can still enable
	* channel 0 here at least, but channel 1 has to be enabled by
	* firmware or arch code. We still set both to 16 bits mode.
	*/
	static unsigned int __devinit init_chipset_sl82c105(struct pci_dev dev, const char msg)
	{
	u32 val;

	DBG(("init_chipset_sl82c105()\n"));

	pci_read_config_dword(dev, 0x40, &val);
	val \|= CTRL_P0EN \| CTRL_P0F16 \| CTRL_P1F16;
	pci_write_config_dword(dev, 0x40, val);
	pci_set_drvdata(dev, (void *)val);

	return dev->irq;
	}

	/*
	* Initialise the chip
	*/
	static void __devinit init_hwif_sl82c105(ide_hwif_t *hwif)
	{
	unsigned int rev;

	DBG(("init_hwif_sl82c105(hwif: ide%d)\n", hwif->index));

	hwif->tuneproc = &sl82c105_tune_drive;
	hwif->selectproc = &sl82c105_selectproc;
	hwif->resetproc = &sl82c105_resetproc;

	/*
	* We support 32-bit I/O on this interface, and
	* it doesn't have problems with interrupts.
	*/
	hwif->drives[0].io_32bit = hwif->drives[1].io_32bit = 1;
	hwif->drives[0].unmask = hwif->drives[1].unmask = 1;

	/*
	* We always autotune PIO, this is done before DMA is checked,
	* so there's no risk of accidentally disabling DMA
	*/
	hwif->drives[0].autotune = hwif->drives[1].autotune = 1;

	hwif->atapi_dma = 0;
	hwif->mwdma_mask = 0;
	hwif->swdma_mask = 0;
	hwif->autodma = 0;

	if (!hwif->dma_base)
	return;

	rev = sl82c105_bridge_revision(hwif->pci_dev);
	if (rev <= 5) {
	/*
	* Never ever EVER under any circumstances enable
	* DMA when the bridge is this old.
	*/
	printk(" %s: Winbond 553 bridge revision %d, BM-DMA disabled\n",
	hwif->name, rev);
	} else {
	hwif->atapi_dma = 1;
	hwif->mwdma_mask = 0x04;

	hwif->ide_dma_check = &sl82c105_check_drive;
	hwif->ide_dma_on = &sl82c105_ide_dma_on;
	hwif->dma_off_quietly = &sl82c105_dma_off_quietly;
	hwif->ide_dma_lostirq = &sl82c105_ide_dma_lost_irq;
	hwif->dma_start = &sl82c105_ide_dma_start;
	hwif->ide_dma_timeout = &sl82c105_ide_dma_timeout;

	if (!noautodma)
	hwif->autodma = 1;
	hwif->drives[0].autodma = hwif->autodma;
	hwif->drives[1].autodma = hwif->autodma;

	if (hwif->mate)
	hwif->serialized = hwif->mate->serialized = 1;
	}
	}

	static ide_pci_device_t sl82c105_chipset __devinitdata = {
	.name = "W82C105",
	.init_chipset = init_chipset_sl82c105,
	.init_hwif = init_hwif_sl82c105,
	.channels = 2,
	.autodma = NOAUTODMA,
	.enablebits = {{0x40,0x01,0x01}, {0x40,0x10,0x10}},
	.bootable = ON_BOARD,
	};

	static int __devinit sl82c105_init_one(struct pci_dev dev, const struct pci_device_id id)
	{
	return ide_setup_pci_device(dev, &sl82c105_chipset);
	}

	static struct pci_device_id sl82c105_pci_tbl[] = {
	{ PCI_DEVICE(PCI_VENDOR_ID_WINBOND, PCI_DEVICE_ID_WINBOND_82C105), 0},
	{ 0, },
	};
	MODULE_DEVICE_TABLE(pci, sl82c105_pci_tbl);

	static struct pci_driver driver = {
	.name = "W82C105_IDE",
	.id_table = sl82c105_pci_tbl,
	.probe = sl82c105_init_one,
	};

	static int __init sl82c105_ide_init(void)
	{
	return ide_pci_register_driver(&driver);
	}

	module_init(sl82c105_ide_init);

	MODULE_DESCRIPTION("PCI driver module for W82C105 IDE");
	MODULE_LICENSE("GPL");