| if ARCH_IXP4XX |
| |
| config ARCH_SUPPORTS_BIG_ENDIAN |
| bool |
| default y |
| |
| menu "Intel IXP4xx Implementation Options" |
| |
| comment "IXP4xx Platforms" |
| |
| config MACH_NSLU2 |
| bool |
| prompt "Linksys NSLU2" |
| select PCI |
| help |
| Say 'Y' here if you want your kernel to support Linksys's |
| NSLU2 NAS device. For more information on this platform, |
| see http://www.nslu2-linux.org |
| |
| config ARCH_AVILA |
| bool "Avila" |
| select PCI |
| help |
| Say 'Y' here if you want your kernel to support the Gateworks |
| Avila Network Platform. For more information on this platform, |
| see <file:Documentation/arm/IXP4xx>. |
| |
| config ARCH_ADI_COYOTE |
| bool "Coyote" |
| select PCI |
| help |
| Say 'Y' here if you want your kernel to support the ADI |
| Engineering Coyote Gateway Reference Platform. For more |
| information on this platform, see <file:Documentation/arm/IXP4xx>. |
| |
| config ARCH_IXDP425 |
| bool "IXDP425" |
| help |
| Say 'Y' here if you want your kernel to support Intel's |
| IXDP425 Development Platform (Also known as Richfield). |
| For more information on this platform, see <file:Documentation/arm/IXP4xx>. |
| |
| config MACH_IXDPG425 |
| bool "IXDPG425" |
| help |
| Say 'Y' here if you want your kernel to support Intel's |
| IXDPG425 Development Platform (Also known as Montajade). |
| For more information on this platform, see <file:Documentation/arm/IXP4xx>. |
| |
| config MACH_IXDP465 |
| bool "IXDP465" |
| help |
| Say 'Y' here if you want your kernel to support Intel's |
| IXDP465 Development Platform (Also known as BMP). |
| For more information on this platform, see <file:Documentation/arm/IXP4xx>. |
| |
| |
| # |
| # IXCDP1100 is the exact same HW as IXDP425, but with a different machine |
| # number from the bootloader due to marketing monkeys, so we just enable it |
| # by default if IXDP425 is enabled. |
| # |
| config ARCH_IXCDP1100 |
| bool |
| depends on ARCH_IXDP425 |
| default y |
| |
| config ARCH_PRPMC1100 |
| bool "PrPMC1100" |
| help |
| Say 'Y' here if you want your kernel to support the Motorola |
| PrPCM1100 Processor Mezanine Module. For more information on |
| this platform, see <file:Documentation/arm/IXP4xx>. |
| |
| config MACH_NAS100D |
| bool |
| prompt "NAS100D" |
| select PCI |
| help |
| Say 'Y' here if you want your kernel to support Iomega's |
| NAS 100d device. For more information on this platform, |
| see http://www.nslu2-linux.org/wiki/NAS100d/HomePage |
| |
| # |
| # Avila and IXDP share the same source for now. Will change in future |
| # |
| config ARCH_IXDP4XX |
| bool |
| depends on ARCH_IXDP425 || ARCH_AVILA || MACH_IXDP465 |
| default y |
| |
| # |
| # Certain registers and IRQs are only enabled if supporting IXP465 CPUs |
| # |
| config CPU_IXP46X |
| bool |
| depends on MACH_IXDP465 |
| default y |
| |
| config MACH_GTWX5715 |
| bool "Gemtek WX5715 (Linksys WRV54G)" |
| depends on ARCH_IXP4XX |
| select PCI |
| help |
| This board is currently inside the Linksys WRV54G Gateways. |
| |
| IXP425 - 266mhz |
| 32mb SDRAM |
| 8mb Flash |
| miniPCI slot 0 does not have a card connector soldered to the board |
| miniPCI slot 1 has an ISL3880 802.11g card (Prism54) |
| npe0 is connected to a Kendin KS8995M Switch (4 ports) |
| npe1 is the "wan" port |
| "Console" UART is available on J11 as console |
| "High Speed" UART is n/c (as far as I can tell) |
| 20 Pin ARM/Xscale JTAG interface on J2 |
| |
| comment "IXP4xx Options" |
| |
| config DMABOUNCE |
| bool |
| default y |
| depends on PCI |
| |
| config IXP4XX_INDIRECT_PCI |
| bool "Use indirect PCI memory access" |
| depends on PCI |
| help |
| IXP4xx provides two methods of accessing PCI memory space: |
| |
| 1) A direct mapped window from 0x48000000 to 0x4bffffff (64MB). |
| To access PCI via this space, we simply ioremap() the BAR |
| into the kernel and we can use the standard read[bwl]/write[bwl] |
| macros. This is the preferred method due to speed but it |
| limits the system to just 64MB of PCI memory. This can be |
| problematic if using video cards and other memory-heavy devices. |
| |
| 2) If > 64MB of memory space is required, the IXP4xx can be |
| configured to use indirect registers to access PCI This allows |
| for up to 128MB (0x48000000 to 0x4fffffff) of memory on the bus. |
| The disadvantage of this is that every PCI access requires |
| three local register accesses plus a spinlock, but in some |
| cases the performance hit is acceptable. In addition, you cannot |
| mmap() PCI devices in this case due to the indirect nature |
| of the PCI window. |
| |
| By default, the direct method is used. Choose this option if you |
| need to use the indirect method instead. If you don't know |
| what you need, leave this option unselected. |
| |
| endmenu |
| |
| endif |