arch/arm/mach-s3c2410/mach-n30.c

/* Machine specific code for the Acer n30 PDA.
 *
 * Copyright (c) 2003-2005 Simtec Electronics
 *	Ben Dooks <ben@simtec.co.uk>
 *
 * Copyright (c) 2005-2008 Christer Weinigel <christer@weinigel.se>
 *
 * There is a wiki with more information about the n30 port at
 * http://handhelds.org/moin/moin.cgi/AcerN30Documentation .
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License version 2 as
 * published by the Free Software Foundation.
*/

#include <linux/kernel.h>
#include <linux/types.h>

#include <linux/delay.h>
#include <linux/init.h>
#include <linux/interrupt.h>
#include <linux/platform_device.h>
#include <linux/serial_core.h>
#include <linux/timer.h>

#include <asm/hardware.h>
#include <asm/io.h>
#include <asm/irq.h>
#include <asm/mach-types.h>

#include <asm/arch/regs-gpio.h>

#include <asm/mach/arch.h>
#include <asm/mach/irq.h>
#include <asm/mach/map.h>

#include <asm/plat-s3c/iic.h>
#include <asm/plat-s3c/regs-serial.h>

#include <asm/plat-s3c24xx/clock.h>
#include <asm/plat-s3c24xx/cpu.h>
#include <asm/plat-s3c24xx/devs.h>
#include <asm/plat-s3c24xx/s3c2410.h>

static struct map_desc n30_iodesc[] __initdata = {
	/* nothing here yet */
};

static struct s3c2410_uartcfg n30_uartcfgs[] = {
	/* Normal serial port */
	[0] = {
		.hwport	     = 0,
		.flags	     = 0,
		.ucon	     = 0x2c5,
		.ulcon	     = 0x03,
		.ufcon	     = 0x51,
	},
	/* IR port */
	[1] = {
		.hwport	     = 1,
		.flags	     = 0,
		.uart_flags  = UPF_CONS_FLOW,
		.ucon	     = 0x2c5,
		.ulcon	     = 0x43,
		.ufcon	     = 0x51,
	},
	/* The BlueTooth controller is connected to port 2 */
	[2] = {
		.hwport	     = 2,
		.flags	     = 0,
		.ucon	     = 0x2c5,
		.ulcon	     = 0x03,
		.ufcon	     = 0x51,
	},
};

static struct platform_device *n30_devices[] __initdata = {
	&s3c_device_lcd,
	&s3c_device_wdt,
	&s3c_device_i2c,
	&s3c_device_iis,
	&s3c_device_usb,
	&s3c_device_usbgadget,
};

static struct s3c2410_platform_i2c n30_i2ccfg = {
	.flags		= 0,
	.slave_addr	= 0x10,
	.bus_freq	= 10*1000,
	.max_freq	= 10*1000,
};

static void __init n30_map_io(void)
{
	s3c24xx_init_io(n30_iodesc, ARRAY_SIZE(n30_iodesc));
	s3c24xx_init_clocks(0);
	s3c24xx_init_uarts(n30_uartcfgs, ARRAY_SIZE(n30_uartcfgs));
}

static void __init n30_init_irq(void)
{
	s3c24xx_init_irq();
}

/* GPB3 is the line that controls the pull-up for the USB D+ line */

static void __init n30_init(void)
{
	s3c_device_i2c.dev.platform_data = &n30_i2ccfg;

	/* Turn off suspend on both USB ports, and switch the
	 * selectable USB port to USB device mode. */

	s3c2410_modify_misccr(S3C2410_MISCCR_USBHOST |
			      S3C2410_MISCCR_USBSUSPND0 |
			      S3C2410_MISCCR_USBSUSPND1, 0x0);

	platform_add_devices(n30_devices, ARRAY_SIZE(n30_devices));
}

MACHINE_START(N30, "Acer-N30")
	/* Maintainer: Christer Weinigel <christer@weinigel.se>,
				Ben Dooks <ben-linux@fluff.org>
	*/
	.phys_io	= S3C2410_PA_UART,
	.io_pg_offst	= (((u32)S3C24XX_VA_UART) >> 18) & 0xfffc,
	.boot_params	= S3C2410_SDRAM_PA + 0x100,
	.timer		= &s3c24xx_timer,
	.init_machine	= n30_init,
	.init_irq	= n30_init_irq,
	.map_io		= n30_map_io,
MACHINE_END