Christopher Bostic | ac0385d | 2017-06-06 16:08:54 -0500 | [diff] [blame] | 1 | /* |
| 2 | * A FSI master controller, using a simple GPIO bit-banging interface |
| 3 | */ |
| 4 | |
| 5 | #include <linux/crc4.h> |
| 6 | #include <linux/delay.h> |
| 7 | #include <linux/device.h> |
| 8 | #include <linux/fsi.h> |
| 9 | #include <linux/gpio/consumer.h> |
| 10 | #include <linux/io.h> |
| 11 | #include <linux/module.h> |
| 12 | #include <linux/platform_device.h> |
| 13 | #include <linux/slab.h> |
| 14 | #include <linux/spinlock.h> |
| 15 | |
| 16 | #include "fsi-master.h" |
| 17 | |
| 18 | #define FSI_GPIO_STD_DLY 1 /* Standard pin delay in nS */ |
| 19 | #define FSI_ECHO_DELAY_CLOCKS 16 /* Number clocks for echo delay */ |
| 20 | #define FSI_PRE_BREAK_CLOCKS 50 /* Number clocks to prep for break */ |
| 21 | #define FSI_BREAK_CLOCKS 256 /* Number of clocks to issue break */ |
| 22 | #define FSI_POST_BREAK_CLOCKS 16000 /* Number clocks to set up cfam */ |
| 23 | #define FSI_INIT_CLOCKS 5000 /* Clock out any old data */ |
| 24 | #define FSI_GPIO_STD_DELAY 10 /* Standard GPIO delay in nS */ |
| 25 | /* todo: adjust down as low as */ |
| 26 | /* possible or eliminate */ |
| 27 | #define FSI_GPIO_CMD_DPOLL 0x2 |
| 28 | #define FSI_GPIO_CMD_TERM 0x3f |
| 29 | #define FSI_GPIO_CMD_ABS_AR 0x4 |
| 30 | |
| 31 | #define FSI_GPIO_DPOLL_CLOCKS 100 /* < 21 will cause slave to hang */ |
| 32 | |
| 33 | /* Bus errors */ |
| 34 | #define FSI_GPIO_ERR_BUSY 1 /* Slave stuck in busy state */ |
| 35 | #define FSI_GPIO_RESP_ERRA 2 /* Any (misc) Error */ |
| 36 | #define FSI_GPIO_RESP_ERRC 3 /* Slave reports master CRC error */ |
| 37 | #define FSI_GPIO_MTOE 4 /* Master time out error */ |
| 38 | #define FSI_GPIO_CRC_INVAL 5 /* Master reports slave CRC error */ |
| 39 | |
| 40 | /* Normal slave responses */ |
| 41 | #define FSI_GPIO_RESP_BUSY 1 |
| 42 | #define FSI_GPIO_RESP_ACK 0 |
| 43 | #define FSI_GPIO_RESP_ACKD 4 |
| 44 | |
| 45 | #define FSI_GPIO_MAX_BUSY 100 |
| 46 | #define FSI_GPIO_MTOE_COUNT 1000 |
| 47 | #define FSI_GPIO_DRAIN_BITS 20 |
| 48 | #define FSI_GPIO_CRC_SIZE 4 |
| 49 | #define FSI_GPIO_MSG_ID_SIZE 2 |
| 50 | #define FSI_GPIO_MSG_RESPID_SIZE 2 |
| 51 | #define FSI_GPIO_PRIME_SLAVE_CLOCKS 100 |
| 52 | |
| 53 | struct fsi_master_gpio { |
| 54 | struct fsi_master master; |
| 55 | struct device *dev; |
| 56 | spinlock_t cmd_lock; /* Lock for commands */ |
| 57 | struct gpio_desc *gpio_clk; |
| 58 | struct gpio_desc *gpio_data; |
| 59 | struct gpio_desc *gpio_trans; /* Voltage translator */ |
| 60 | struct gpio_desc *gpio_enable; /* FSI enable */ |
| 61 | struct gpio_desc *gpio_mux; /* Mux control */ |
| 62 | }; |
| 63 | |
Jeremy Kerr | 1247cf7 | 2017-06-06 16:08:55 -0500 | [diff] [blame] | 64 | #define CREATE_TRACE_POINTS |
| 65 | #include <trace/events/fsi_master_gpio.h> |
| 66 | |
Christopher Bostic | ac0385d | 2017-06-06 16:08:54 -0500 | [diff] [blame] | 67 | #define to_fsi_master_gpio(m) container_of(m, struct fsi_master_gpio, master) |
| 68 | |
| 69 | struct fsi_gpio_msg { |
| 70 | uint64_t msg; |
| 71 | uint8_t bits; |
| 72 | }; |
| 73 | |
| 74 | static void clock_toggle(struct fsi_master_gpio *master, int count) |
| 75 | { |
| 76 | int i; |
| 77 | |
| 78 | for (i = 0; i < count; i++) { |
| 79 | ndelay(FSI_GPIO_STD_DLY); |
| 80 | gpiod_set_value(master->gpio_clk, 0); |
| 81 | ndelay(FSI_GPIO_STD_DLY); |
| 82 | gpiod_set_value(master->gpio_clk, 1); |
| 83 | } |
| 84 | } |
| 85 | |
| 86 | static int sda_in(struct fsi_master_gpio *master) |
| 87 | { |
| 88 | int in; |
| 89 | |
| 90 | ndelay(FSI_GPIO_STD_DLY); |
| 91 | in = gpiod_get_value(master->gpio_data); |
| 92 | return in ? 1 : 0; |
| 93 | } |
| 94 | |
| 95 | static void sda_out(struct fsi_master_gpio *master, int value) |
| 96 | { |
| 97 | gpiod_set_value(master->gpio_data, value); |
| 98 | } |
| 99 | |
| 100 | static void set_sda_input(struct fsi_master_gpio *master) |
| 101 | { |
| 102 | gpiod_direction_input(master->gpio_data); |
| 103 | gpiod_set_value(master->gpio_trans, 0); |
| 104 | } |
| 105 | |
| 106 | static void set_sda_output(struct fsi_master_gpio *master, int value) |
| 107 | { |
| 108 | gpiod_set_value(master->gpio_trans, 1); |
| 109 | gpiod_direction_output(master->gpio_data, value); |
| 110 | } |
| 111 | |
| 112 | static void clock_zeros(struct fsi_master_gpio *master, int count) |
| 113 | { |
| 114 | set_sda_output(master, 1); |
| 115 | clock_toggle(master, count); |
| 116 | } |
| 117 | |
| 118 | static void serial_in(struct fsi_master_gpio *master, struct fsi_gpio_msg *msg, |
| 119 | uint8_t num_bits) |
| 120 | { |
| 121 | uint8_t bit, in_bit; |
| 122 | |
| 123 | set_sda_input(master); |
| 124 | |
| 125 | for (bit = 0; bit < num_bits; bit++) { |
| 126 | clock_toggle(master, 1); |
| 127 | in_bit = sda_in(master); |
| 128 | msg->msg <<= 1; |
| 129 | msg->msg |= ~in_bit & 0x1; /* Data is active low */ |
| 130 | } |
| 131 | msg->bits += num_bits; |
Jeremy Kerr | 1247cf7 | 2017-06-06 16:08:55 -0500 | [diff] [blame] | 132 | |
| 133 | trace_fsi_master_gpio_in(master, num_bits, msg->msg); |
Christopher Bostic | ac0385d | 2017-06-06 16:08:54 -0500 | [diff] [blame] | 134 | } |
| 135 | |
| 136 | static void serial_out(struct fsi_master_gpio *master, |
| 137 | const struct fsi_gpio_msg *cmd) |
| 138 | { |
| 139 | uint8_t bit; |
| 140 | uint64_t msg = ~cmd->msg; /* Data is active low */ |
| 141 | uint64_t sda_mask = 0x1ULL << (cmd->bits - 1); |
| 142 | uint64_t last_bit = ~0; |
| 143 | int next_bit; |
| 144 | |
Jeremy Kerr | 1247cf7 | 2017-06-06 16:08:55 -0500 | [diff] [blame] | 145 | trace_fsi_master_gpio_out(master, cmd->bits, cmd->msg); |
| 146 | |
Christopher Bostic | ac0385d | 2017-06-06 16:08:54 -0500 | [diff] [blame] | 147 | if (!cmd->bits) { |
| 148 | dev_warn(master->dev, "trying to output 0 bits\n"); |
| 149 | return; |
| 150 | } |
| 151 | set_sda_output(master, 0); |
| 152 | |
| 153 | /* Send the start bit */ |
| 154 | sda_out(master, 0); |
| 155 | clock_toggle(master, 1); |
| 156 | |
| 157 | /* Send the message */ |
| 158 | for (bit = 0; bit < cmd->bits; bit++) { |
| 159 | next_bit = (msg & sda_mask) >> (cmd->bits - 1); |
| 160 | if (last_bit ^ next_bit) { |
| 161 | sda_out(master, next_bit); |
| 162 | last_bit = next_bit; |
| 163 | } |
| 164 | clock_toggle(master, 1); |
| 165 | msg <<= 1; |
| 166 | } |
| 167 | } |
| 168 | |
| 169 | static void msg_push_bits(struct fsi_gpio_msg *msg, uint64_t data, int bits) |
| 170 | { |
| 171 | msg->msg <<= bits; |
| 172 | msg->msg |= data & ((1ull << bits) - 1); |
| 173 | msg->bits += bits; |
| 174 | } |
| 175 | |
| 176 | static void msg_push_crc(struct fsi_gpio_msg *msg) |
| 177 | { |
| 178 | uint8_t crc; |
| 179 | int top; |
| 180 | |
| 181 | top = msg->bits & 0x3; |
| 182 | |
| 183 | /* start bit, and any non-aligned top bits */ |
| 184 | crc = crc4(0, 1 << top | msg->msg >> (msg->bits - top), top + 1); |
| 185 | |
| 186 | /* aligned bits */ |
| 187 | crc = crc4(crc, msg->msg, msg->bits - top); |
| 188 | |
| 189 | msg_push_bits(msg, crc, 4); |
| 190 | } |
| 191 | |
| 192 | /* |
| 193 | * Encode an Absolute Address command |
| 194 | */ |
| 195 | static void build_abs_ar_command(struct fsi_gpio_msg *cmd, |
| 196 | uint8_t id, uint32_t addr, size_t size, const void *data) |
| 197 | { |
| 198 | bool write = !!data; |
| 199 | uint8_t ds; |
| 200 | int i; |
| 201 | |
| 202 | cmd->bits = 0; |
| 203 | cmd->msg = 0; |
| 204 | |
| 205 | msg_push_bits(cmd, id, 2); |
| 206 | msg_push_bits(cmd, FSI_GPIO_CMD_ABS_AR, 3); |
| 207 | msg_push_bits(cmd, write ? 0 : 1, 1); |
| 208 | |
| 209 | /* |
| 210 | * The read/write size is encoded in the lower bits of the address |
| 211 | * (as it must be naturally-aligned), and the following ds bit. |
| 212 | * |
| 213 | * size addr:1 addr:0 ds |
| 214 | * 1 x x 0 |
| 215 | * 2 x 0 1 |
| 216 | * 4 0 1 1 |
| 217 | * |
| 218 | */ |
| 219 | ds = size > 1 ? 1 : 0; |
| 220 | addr &= ~(size - 1); |
| 221 | if (size == 4) |
| 222 | addr |= 1; |
| 223 | |
| 224 | msg_push_bits(cmd, addr & ((1 << 21) - 1), 21); |
| 225 | msg_push_bits(cmd, ds, 1); |
| 226 | for (i = 0; write && i < size; i++) |
| 227 | msg_push_bits(cmd, ((uint8_t *)data)[i], 8); |
| 228 | |
| 229 | msg_push_crc(cmd); |
| 230 | } |
| 231 | |
| 232 | static void build_dpoll_command(struct fsi_gpio_msg *cmd, uint8_t slave_id) |
| 233 | { |
| 234 | cmd->bits = 0; |
| 235 | cmd->msg = 0; |
| 236 | |
| 237 | msg_push_bits(cmd, slave_id, 2); |
| 238 | msg_push_bits(cmd, FSI_GPIO_CMD_DPOLL, 3); |
| 239 | msg_push_crc(cmd); |
| 240 | } |
| 241 | |
| 242 | static void echo_delay(struct fsi_master_gpio *master) |
| 243 | { |
| 244 | set_sda_output(master, 1); |
| 245 | clock_toggle(master, FSI_ECHO_DELAY_CLOCKS); |
| 246 | } |
| 247 | |
| 248 | static void build_term_command(struct fsi_gpio_msg *cmd, uint8_t slave_id) |
| 249 | { |
| 250 | cmd->bits = 0; |
| 251 | cmd->msg = 0; |
| 252 | |
| 253 | msg_push_bits(cmd, slave_id, 2); |
| 254 | msg_push_bits(cmd, FSI_GPIO_CMD_TERM, 6); |
| 255 | msg_push_crc(cmd); |
| 256 | } |
| 257 | |
| 258 | /* |
| 259 | * Store information on master errors so handler can detect and clean |
| 260 | * up the bus |
| 261 | */ |
| 262 | static void fsi_master_gpio_error(struct fsi_master_gpio *master, int error) |
| 263 | { |
| 264 | |
| 265 | } |
| 266 | |
| 267 | static int read_one_response(struct fsi_master_gpio *master, |
| 268 | uint8_t data_size, struct fsi_gpio_msg *msgp, uint8_t *tagp) |
| 269 | { |
| 270 | struct fsi_gpio_msg msg; |
| 271 | uint8_t id, tag; |
| 272 | uint32_t crc; |
| 273 | int i; |
| 274 | |
| 275 | /* wait for the start bit */ |
| 276 | for (i = 0; i < FSI_GPIO_MTOE_COUNT; i++) { |
| 277 | msg.bits = 0; |
| 278 | msg.msg = 0; |
| 279 | serial_in(master, &msg, 1); |
| 280 | if (msg.msg) |
| 281 | break; |
| 282 | } |
| 283 | if (i == FSI_GPIO_MTOE_COUNT) { |
| 284 | dev_dbg(master->dev, |
| 285 | "Master time out waiting for response\n"); |
| 286 | fsi_master_gpio_error(master, FSI_GPIO_MTOE); |
| 287 | return -EIO; |
| 288 | } |
| 289 | |
| 290 | msg.bits = 0; |
| 291 | msg.msg = 0; |
| 292 | |
| 293 | /* Read slave ID & response tag */ |
| 294 | serial_in(master, &msg, 4); |
| 295 | |
| 296 | id = (msg.msg >> FSI_GPIO_MSG_RESPID_SIZE) & 0x3; |
| 297 | tag = msg.msg & 0x3; |
| 298 | |
| 299 | /* If we have an ACK and we're expecting data, clock the data in too */ |
| 300 | if (tag == FSI_GPIO_RESP_ACK && data_size) |
| 301 | serial_in(master, &msg, data_size * 8); |
| 302 | |
| 303 | /* read CRC */ |
| 304 | serial_in(master, &msg, FSI_GPIO_CRC_SIZE); |
| 305 | |
| 306 | /* we have a whole message now; check CRC */ |
| 307 | crc = crc4(0, 1, 1); |
| 308 | crc = crc4(crc, msg.msg, msg.bits); |
| 309 | if (crc) { |
| 310 | dev_dbg(master->dev, "ERR response CRC\n"); |
| 311 | fsi_master_gpio_error(master, FSI_GPIO_CRC_INVAL); |
| 312 | return -EIO; |
| 313 | } |
| 314 | |
| 315 | if (msgp) |
| 316 | *msgp = msg; |
| 317 | if (tagp) |
| 318 | *tagp = tag; |
| 319 | |
| 320 | return 0; |
| 321 | } |
| 322 | |
| 323 | static int issue_term(struct fsi_master_gpio *master, uint8_t slave) |
| 324 | { |
| 325 | struct fsi_gpio_msg cmd; |
| 326 | uint8_t tag; |
| 327 | int rc; |
| 328 | |
| 329 | build_term_command(&cmd, slave); |
| 330 | serial_out(master, &cmd); |
| 331 | echo_delay(master); |
| 332 | |
| 333 | rc = read_one_response(master, 0, NULL, &tag); |
| 334 | if (rc < 0) { |
| 335 | dev_err(master->dev, |
| 336 | "TERM failed; lost communication with slave\n"); |
| 337 | return -EIO; |
| 338 | } else if (tag != FSI_GPIO_RESP_ACK) { |
| 339 | dev_err(master->dev, "TERM failed; response %d\n", tag); |
| 340 | return -EIO; |
| 341 | } |
| 342 | |
| 343 | return 0; |
| 344 | } |
| 345 | |
| 346 | static int poll_for_response(struct fsi_master_gpio *master, |
| 347 | uint8_t slave, uint8_t size, void *data) |
| 348 | { |
| 349 | struct fsi_gpio_msg response, cmd; |
| 350 | int busy_count = 0, rc, i; |
| 351 | uint8_t tag; |
| 352 | uint8_t *data_byte = data; |
| 353 | |
| 354 | retry: |
| 355 | rc = read_one_response(master, size, &response, &tag); |
| 356 | if (rc) |
| 357 | return rc; |
| 358 | |
| 359 | switch (tag) { |
| 360 | case FSI_GPIO_RESP_ACK: |
| 361 | if (size && data) { |
| 362 | uint64_t val = response.msg; |
| 363 | /* clear crc & mask */ |
| 364 | val >>= 4; |
| 365 | val &= (1ull << (size * 8)) - 1; |
| 366 | |
| 367 | for (i = 0; i < size; i++) { |
| 368 | data_byte[size-i-1] = val; |
| 369 | val >>= 8; |
| 370 | } |
| 371 | } |
| 372 | break; |
| 373 | case FSI_GPIO_RESP_BUSY: |
| 374 | /* |
| 375 | * Its necessary to clock slave before issuing |
| 376 | * d-poll, not indicated in the hardware protocol |
| 377 | * spec. < 20 clocks causes slave to hang, 21 ok. |
| 378 | */ |
| 379 | clock_zeros(master, FSI_GPIO_DPOLL_CLOCKS); |
| 380 | if (busy_count++ < FSI_GPIO_MAX_BUSY) { |
| 381 | build_dpoll_command(&cmd, slave); |
| 382 | serial_out(master, &cmd); |
| 383 | echo_delay(master); |
| 384 | goto retry; |
| 385 | } |
| 386 | dev_warn(master->dev, |
| 387 | "ERR slave is stuck in busy state, issuing TERM\n"); |
| 388 | issue_term(master, slave); |
| 389 | rc = -EIO; |
| 390 | break; |
| 391 | |
| 392 | case FSI_GPIO_RESP_ERRA: |
| 393 | case FSI_GPIO_RESP_ERRC: |
| 394 | dev_dbg(master->dev, "ERR%c received: 0x%x\n", |
| 395 | tag == FSI_GPIO_RESP_ERRA ? 'A' : 'C', |
| 396 | (int)response.msg); |
| 397 | fsi_master_gpio_error(master, response.msg); |
| 398 | rc = -EIO; |
| 399 | break; |
| 400 | } |
| 401 | |
| 402 | /* Clock the slave enough to be ready for next operation */ |
| 403 | clock_zeros(master, FSI_GPIO_PRIME_SLAVE_CLOCKS); |
| 404 | return rc; |
| 405 | } |
| 406 | |
| 407 | static int fsi_master_gpio_xfer(struct fsi_master_gpio *master, uint8_t slave, |
| 408 | struct fsi_gpio_msg *cmd, size_t resp_len, void *resp) |
| 409 | { |
| 410 | unsigned long flags; |
| 411 | int rc; |
| 412 | |
| 413 | spin_lock_irqsave(&master->cmd_lock, flags); |
| 414 | serial_out(master, cmd); |
| 415 | echo_delay(master); |
| 416 | rc = poll_for_response(master, slave, resp_len, resp); |
| 417 | spin_unlock_irqrestore(&master->cmd_lock, flags); |
| 418 | |
| 419 | return rc; |
| 420 | } |
| 421 | |
| 422 | static int fsi_master_gpio_read(struct fsi_master *_master, int link, |
| 423 | uint8_t id, uint32_t addr, void *val, size_t size) |
| 424 | { |
| 425 | struct fsi_master_gpio *master = to_fsi_master_gpio(_master); |
| 426 | struct fsi_gpio_msg cmd; |
| 427 | |
| 428 | if (link != 0) |
| 429 | return -ENODEV; |
| 430 | |
| 431 | build_abs_ar_command(&cmd, id, addr, size, NULL); |
| 432 | return fsi_master_gpio_xfer(master, id, &cmd, size, val); |
| 433 | } |
| 434 | |
| 435 | static int fsi_master_gpio_write(struct fsi_master *_master, int link, |
| 436 | uint8_t id, uint32_t addr, const void *val, size_t size) |
| 437 | { |
| 438 | struct fsi_master_gpio *master = to_fsi_master_gpio(_master); |
| 439 | struct fsi_gpio_msg cmd; |
| 440 | |
| 441 | if (link != 0) |
| 442 | return -ENODEV; |
| 443 | |
| 444 | build_abs_ar_command(&cmd, id, addr, size, val); |
| 445 | return fsi_master_gpio_xfer(master, id, &cmd, 0, NULL); |
| 446 | } |
| 447 | |
| 448 | static int fsi_master_gpio_term(struct fsi_master *_master, |
| 449 | int link, uint8_t id) |
| 450 | { |
| 451 | struct fsi_master_gpio *master = to_fsi_master_gpio(_master); |
| 452 | struct fsi_gpio_msg cmd; |
| 453 | |
| 454 | if (link != 0) |
| 455 | return -ENODEV; |
| 456 | |
| 457 | build_term_command(&cmd, id); |
| 458 | return fsi_master_gpio_xfer(master, id, &cmd, 0, NULL); |
| 459 | } |
| 460 | |
| 461 | static int fsi_master_gpio_break(struct fsi_master *_master, int link) |
| 462 | { |
| 463 | struct fsi_master_gpio *master = to_fsi_master_gpio(_master); |
| 464 | |
| 465 | if (link != 0) |
| 466 | return -ENODEV; |
| 467 | |
Jeremy Kerr | 1247cf7 | 2017-06-06 16:08:55 -0500 | [diff] [blame] | 468 | trace_fsi_master_gpio_break(master); |
| 469 | |
Christopher Bostic | ac0385d | 2017-06-06 16:08:54 -0500 | [diff] [blame] | 470 | set_sda_output(master, 1); |
| 471 | sda_out(master, 1); |
| 472 | clock_toggle(master, FSI_PRE_BREAK_CLOCKS); |
| 473 | sda_out(master, 0); |
| 474 | clock_toggle(master, FSI_BREAK_CLOCKS); |
| 475 | echo_delay(master); |
| 476 | sda_out(master, 1); |
| 477 | clock_toggle(master, FSI_POST_BREAK_CLOCKS); |
| 478 | |
| 479 | /* Wait for logic reset to take effect */ |
| 480 | udelay(200); |
| 481 | |
| 482 | return 0; |
| 483 | } |
| 484 | |
| 485 | static void fsi_master_gpio_init(struct fsi_master_gpio *master) |
| 486 | { |
| 487 | gpiod_direction_output(master->gpio_mux, 1); |
| 488 | gpiod_direction_output(master->gpio_trans, 1); |
| 489 | gpiod_direction_output(master->gpio_enable, 1); |
| 490 | gpiod_direction_output(master->gpio_clk, 1); |
| 491 | gpiod_direction_output(master->gpio_data, 1); |
| 492 | |
| 493 | /* todo: evaluate if clocks can be reduced */ |
| 494 | clock_zeros(master, FSI_INIT_CLOCKS); |
| 495 | } |
| 496 | |
| 497 | static int fsi_master_gpio_link_enable(struct fsi_master *_master, int link) |
| 498 | { |
| 499 | struct fsi_master_gpio *master = to_fsi_master_gpio(_master); |
| 500 | |
| 501 | if (link != 0) |
| 502 | return -ENODEV; |
| 503 | gpiod_set_value(master->gpio_enable, 1); |
| 504 | |
| 505 | return 0; |
| 506 | } |
| 507 | |
| 508 | static int fsi_master_gpio_probe(struct platform_device *pdev) |
| 509 | { |
| 510 | struct fsi_master_gpio *master; |
| 511 | struct gpio_desc *gpio; |
| 512 | |
| 513 | master = devm_kzalloc(&pdev->dev, sizeof(*master), GFP_KERNEL); |
| 514 | if (!master) |
| 515 | return -ENOMEM; |
| 516 | |
| 517 | master->dev = &pdev->dev; |
| 518 | master->master.dev.parent = master->dev; |
| 519 | |
| 520 | gpio = devm_gpiod_get(&pdev->dev, "clock", 0); |
| 521 | if (IS_ERR(gpio)) { |
| 522 | dev_err(&pdev->dev, "failed to get clock gpio\n"); |
| 523 | return PTR_ERR(gpio); |
| 524 | } |
| 525 | master->gpio_clk = gpio; |
| 526 | |
| 527 | gpio = devm_gpiod_get(&pdev->dev, "data", 0); |
| 528 | if (IS_ERR(gpio)) { |
| 529 | dev_err(&pdev->dev, "failed to get data gpio\n"); |
| 530 | return PTR_ERR(gpio); |
| 531 | } |
| 532 | master->gpio_data = gpio; |
| 533 | |
| 534 | /* Optional GPIOs */ |
| 535 | gpio = devm_gpiod_get_optional(&pdev->dev, "trans", 0); |
| 536 | if (IS_ERR(gpio)) { |
| 537 | dev_err(&pdev->dev, "failed to get trans gpio\n"); |
| 538 | return PTR_ERR(gpio); |
| 539 | } |
| 540 | master->gpio_trans = gpio; |
| 541 | |
| 542 | gpio = devm_gpiod_get_optional(&pdev->dev, "enable", 0); |
| 543 | if (IS_ERR(gpio)) { |
| 544 | dev_err(&pdev->dev, "failed to get enable gpio\n"); |
| 545 | return PTR_ERR(gpio); |
| 546 | } |
| 547 | master->gpio_enable = gpio; |
| 548 | |
| 549 | gpio = devm_gpiod_get_optional(&pdev->dev, "mux", 0); |
| 550 | if (IS_ERR(gpio)) { |
| 551 | dev_err(&pdev->dev, "failed to get mux gpio\n"); |
| 552 | return PTR_ERR(gpio); |
| 553 | } |
| 554 | master->gpio_mux = gpio; |
| 555 | |
| 556 | master->master.n_links = 1; |
Jeremy Kerr | 4af889b | 2017-06-06 16:08:58 -0500 | [diff] [blame] | 557 | master->master.flags = FSI_MASTER_FLAG_SWCLOCK; |
Christopher Bostic | ac0385d | 2017-06-06 16:08:54 -0500 | [diff] [blame] | 558 | master->master.read = fsi_master_gpio_read; |
| 559 | master->master.write = fsi_master_gpio_write; |
| 560 | master->master.term = fsi_master_gpio_term; |
| 561 | master->master.send_break = fsi_master_gpio_break; |
| 562 | master->master.link_enable = fsi_master_gpio_link_enable; |
| 563 | platform_set_drvdata(pdev, master); |
| 564 | spin_lock_init(&master->cmd_lock); |
| 565 | |
| 566 | fsi_master_gpio_init(master); |
| 567 | |
| 568 | return fsi_master_register(&master->master); |
| 569 | } |
| 570 | |
| 571 | |
| 572 | static int fsi_master_gpio_remove(struct platform_device *pdev) |
| 573 | { |
| 574 | struct fsi_master_gpio *master = platform_get_drvdata(pdev); |
| 575 | |
| 576 | devm_gpiod_put(&pdev->dev, master->gpio_clk); |
| 577 | devm_gpiod_put(&pdev->dev, master->gpio_data); |
| 578 | if (master->gpio_trans) |
| 579 | devm_gpiod_put(&pdev->dev, master->gpio_trans); |
| 580 | if (master->gpio_enable) |
| 581 | devm_gpiod_put(&pdev->dev, master->gpio_enable); |
| 582 | if (master->gpio_mux) |
| 583 | devm_gpiod_put(&pdev->dev, master->gpio_mux); |
| 584 | fsi_master_unregister(&master->master); |
| 585 | |
| 586 | return 0; |
| 587 | } |
| 588 | |
| 589 | static const struct of_device_id fsi_master_gpio_match[] = { |
| 590 | { .compatible = "fsi-master-gpio" }, |
| 591 | { }, |
| 592 | }; |
| 593 | |
| 594 | static struct platform_driver fsi_master_gpio_driver = { |
| 595 | .driver = { |
| 596 | .name = "fsi-master-gpio", |
| 597 | .of_match_table = fsi_master_gpio_match, |
| 598 | }, |
| 599 | .probe = fsi_master_gpio_probe, |
| 600 | .remove = fsi_master_gpio_remove, |
| 601 | }; |
| 602 | |
| 603 | module_platform_driver(fsi_master_gpio_driver); |
| 604 | MODULE_LICENSE("GPL"); |