blob: 5064e06e25b44225ed855ce72bb5baff0e5873b2 [file] [log] [blame]
Linus Torvalds1da177e2005-04-16 15:20:36 -07001#
2# USB Host Controller Drivers
3#
4comment "USB Host Controller Drivers"
Linus Torvalds1da177e2005-04-16 15:20:36 -07005
Peter Korsgaarde9b29ff2008-04-27 08:59:45 +02006config USB_C67X00_HCD
7 tristate "Cypress C67x00 HCD support"
Peter Korsgaarde9b29ff2008-04-27 08:59:45 +02008 help
9 The Cypress C67x00 (EZ-Host/EZ-OTG) chips are dual-role
10 host/peripheral/OTG USB controllers.
11
12 Enable this option to support this chip in host controller mode.
13 If unsure, say N.
14
15 To compile this driver as a module, choose M here: the
16 module will be called c67x00.
17
Sarah Sharpeb6bab12009-04-29 19:07:13 -070018config USB_XHCI_HCD
Greg Kroah-Hartmaneb83be92012-09-14 21:15:50 -070019 tristate "xHCI HCD (USB 3.0) support"
Sarah Sharpeb6bab12009-04-29 19:07:13 -070020 ---help---
21 The eXtensible Host Controller Interface (xHCI) is standard for USB 3.0
22 "SuperSpeed" host controller hardware.
23
24 To compile this driver as a module, choose M here: the
25 module will be called xhci-hcd.
26
Florian Fainelli0fcb9982013-04-09 14:29:29 +020027if USB_XHCI_HCD
28
Sebastian Andrzej Siewior3429e912012-03-13 16:57:41 +020029config USB_XHCI_PLATFORM
30 tristate
Sebastian Andrzej Siewior3429e912012-03-13 16:57:41 +020031
Sarah Sharpeb6bab12009-04-29 19:07:13 -070032config USB_XHCI_HCD_DEBUGGING
33 bool "Debugging for the xHCI host controller"
Sarah Sharpeb6bab12009-04-29 19:07:13 -070034 ---help---
35 Say 'Y' to turn on debugging for the xHCI host controller driver.
36 This will spew debugging output, even in interrupt context.
37 This should only be used for debugging xHCI driver bugs.
38
39 If unsure, say N.
40
Florian Fainelli0fcb9982013-04-09 14:29:29 +020041endif # USB_XHCI_HCD
42
Linus Torvalds1da177e2005-04-16 15:20:36 -070043config USB_EHCI_HCD
44 tristate "EHCI HCD (USB 2.0) support"
Linus Torvalds1da177e2005-04-16 15:20:36 -070045 ---help---
46 The Enhanced Host Controller Interface (EHCI) is standard for USB 2.0
47 "high speed" (480 Mbit/sec, 60 Mbyte/sec) host controller hardware.
48 If your USB host controller supports USB 2.0, you will likely want to
Thierry Vignaudb967c882009-02-11 13:31:05 -080049 configure this Host Controller Driver.
Linus Torvalds1da177e2005-04-16 15:20:36 -070050
51 EHCI controllers are packaged with "companion" host controllers (OHCI
52 or UHCI) to handle USB 1.1 devices connected to root hub ports. Ports
Jesper Juhlb3c29d82006-01-10 00:35:22 +010053 will connect to EHCI if the device is high speed, otherwise they
Linus Torvalds1da177e2005-04-16 15:20:36 -070054 connect to a companion controller. If you configure EHCI, you should
55 probably configure the OHCI (for NEC and some other vendors) USB Host
56 Controller Driver or UHCI (for Via motherboards) Host Controller
57 Driver too.
58
59 You may want to read <file:Documentation/usb/ehci.txt>.
60
61 To compile this driver as a module, choose M here: the
62 module will be called ehci-hcd.
63
Linus Torvalds1da177e2005-04-16 15:20:36 -070064config USB_EHCI_ROOT_HUB_TT
Robert P. J. Day9ec249a2008-03-08 03:27:44 -050065 bool "Root Hub Transaction Translators"
Marek Vasutb12909b2012-05-15 06:10:20 +020066 depends on USB_EHCI_HCD || USB_CHIPIDEA_HOST
Linus Torvalds1da177e2005-04-16 15:20:36 -070067 ---help---
68 Some EHCI chips have vendor-specific extensions to integrate
69 transaction translators, so that no OHCI or UHCI companion
70 controller is needed. It's safe to say "y" even if your
71 controller doesn't support this feature.
72
Dan Streetmanba47f662006-05-24 09:39:16 -070073 This supports the EHCI implementation that's originally
74 from ARC, and has since changed hands a few times.
75
76config USB_EHCI_TT_NEWSCHED
Alan Stern37cd6812010-05-21 17:08:21 -040077 bool "Improved Transaction Translator scheduling"
Marek Vasutb12909b2012-05-15 06:10:20 +020078 depends on USB_EHCI_HCD || USB_CHIPIDEA_HOST
Alan Stern37cd6812010-05-21 17:08:21 -040079 default y
Dan Streetmanba47f662006-05-24 09:39:16 -070080 ---help---
81 This changes the periodic scheduling code to fill more of the low
82 and full speed bandwidth available from the Transaction Translator
83 (TT) in USB 2.0 hubs. Without this, only one transfer will be
84 issued in each microframe, significantly reducing the number of
85 periodic low/fullspeed transfers possible.
86
87 If you have multiple periodic low/fullspeed devices connected to a
88 highspeed USB hub which is connected to a highspeed USB Host
89 Controller, and some of those devices will not work correctly
Alan Stern37cd6812010-05-21 17:08:21 -040090 (possibly due to "ENOSPC" or "-28" errors), say Y. Conversely, if
91 you have only one such device and it doesn't work, you could try
92 saying N.
Dan Streetmanba47f662006-05-24 09:39:16 -070093
Alan Stern37cd6812010-05-21 17:08:21 -040094 If unsure, say Y.
Linus Torvalds1da177e2005-04-16 15:20:36 -070095
Florian Fainelli42443dc2013-04-09 14:29:27 +020096config USB_FSL_MPH_DR_OF
97 tristate
98
99if USB_EHCI_HCD
100
Alan Sternadfa79d2012-11-01 11:13:04 -0400101config USB_EHCI_PCI
102 tristate
Florian Fainelli42443dc2013-04-09 14:29:27 +0200103 depends on PCI
Alan Sternadfa79d2012-11-01 11:13:04 -0400104 default y
105
Anoop22ced6872011-02-24 19:26:28 +0530106config USB_EHCI_HCD_PMC_MSP
107 tristate "EHCI support for on-chip PMC MSP71xx USB controller"
Florian Fainelli42443dc2013-04-09 14:29:27 +0200108 depends on MSP_HAS_USB
Anoop22ced6872011-02-24 19:26:28 +0530109 default n
110 select USB_EHCI_BIG_ENDIAN_DESC
111 select USB_EHCI_BIG_ENDIAN_MMIO
112 ---help---
113 Enables support for the onchip USB controller on the PMC_MSP7100 Family SoC's.
114 If unsure, say N.
115
Benjamin Herrenschmidt083522d2006-12-15 06:54:08 +1100116config USB_EHCI_BIG_ENDIAN_MMIO
117 bool
Benjamin Herrenschmidt083522d2006-12-15 06:54:08 +1100118
Stefan Roese6dbd6822007-05-01 09:29:37 -0700119config USB_EHCI_BIG_ENDIAN_DESC
120 bool
Stefan Roese6dbd6822007-05-01 09:29:37 -0700121
Julie Zhu08d3c182009-09-21 16:08:19 -0600122config XPS_USB_HCD_XILINX
123 bool "Use Xilinx usb host EHCI controller core"
Florian Fainelli42443dc2013-04-09 14:29:27 +0200124 depends on (PPC32 || MICROBLAZE)
Julie Zhu08d3c182009-09-21 16:08:19 -0600125 select USB_EHCI_BIG_ENDIAN_DESC
126 select USB_EHCI_BIG_ENDIAN_MMIO
127 ---help---
128 Xilinx xps USB host controller core is EHCI compilant and has
129 transaction translator built-in. It can be configured to either
130 support both high speed and full speed devices, or high speed
131 devices only.
132
Li Yangba029782007-05-11 17:09:55 +0800133config USB_EHCI_FSL
Fabio Estevamc0ca9bc2012-02-02 14:23:34 -0200134 bool "Support for Freescale PPC on-chip EHCI USB controller"
Florian Fainelli42443dc2013-04-09 14:29:27 +0200135 depends on FSL_SOC
Li Yangba029782007-05-11 17:09:55 +0800136 select USB_EHCI_ROOT_HUB_TT
Marc Kleine-Budde018b97d2010-10-29 11:04:49 +0200137 select USB_FSL_MPH_DR_OF if OF
Li Yangba029782007-05-11 17:09:55 +0800138 ---help---
139 Variation of ARC USB block used in some Freescale chips.
140
Daniel Mack7e8d5cd2009-10-28 01:14:59 +0100141config USB_EHCI_MXC
Alan Sterndba63b22013-01-23 13:26:15 -0500142 tristate "Support for Freescale i.MX on-chip EHCI USB controller"
Florian Fainelli42443dc2013-04-09 14:29:27 +0200143 depends on ARCH_MXC
Daniel Mack7e8d5cd2009-10-28 01:14:59 +0100144 select USB_EHCI_ROOT_HUB_TT
145 ---help---
146 Variation of ARC USB block used in some Freescale chips.
147
Keshava Munegowda7f124f42010-11-21 23:23:41 +0530148config USB_EHCI_HCD_OMAP
Alan Stern54a419662013-03-12 12:44:39 +0200149 tristate "EHCI support for OMAP3 and later chips"
Florian Fainelli42443dc2013-04-09 14:29:27 +0200150 depends on ARCH_OMAP
Roger Quadros88650d62013-06-14 12:51:42 +0300151 select NOP_USB_XCEIV
Keshava Munegowda7f124f42010-11-21 23:23:41 +0530152 default y
Paul Bolled132d7f2012-05-07 11:14:59 +0200153 ---help---
Keshava Munegowda7f124f42010-11-21 23:23:41 +0530154 Enables support for the on-chip EHCI controller on
155 OMAP3 and later chips.
156
Manjunath Goudara76dd462013-04-02 18:23:59 +0200157config USB_EHCI_HCD_ORION
158 tristate "Support for Marvell EBU on-chip EHCI USB controller"
159 depends on USB_EHCI_HCD && PLAT_ORION
160 default y
161 ---help---
162 Enables support for the on-chip EHCI controller on Marvell's
163 embedded ARM SoCs, including Orion, Kirkwood, Dove, Armada XP,
164 Armada 370. This is different from the EHCI implementation
165 on Marvell's mobile PXA and MMP SoC, see "EHCI support for
166 Marvell PXA/MMP USB controller" for those.
167
Manjunath Goudar7675d6b2013-04-02 18:24:00 +0200168config USB_EHCI_HCD_SPEAR
169 tristate "Support for ST SPEAr on-chip EHCI USB controller"
170 depends on USB_EHCI_HCD && PLAT_SPEAR
171 default y
172 ---help---
173 Enables support for the on-chip EHCI controller on
174 ST SPEAr chips.
175
Manjunath Goudar97736962013-04-02 18:24:02 +0200176config USB_EHCI_HCD_AT91
177 tristate "Support for Atmel on-chip EHCI USB controller"
178 depends on USB_EHCI_HCD && ARCH_AT91
179 default y
180 ---help---
181 Enables support for the on-chip EHCI controller on
182 Atmel chips.
183
Pavankumar Kondetib0848ae2010-12-07 17:53:56 +0530184config USB_EHCI_MSM
Manjunath Goudar8c68e842013-04-02 18:24:03 +0200185 tristate "Support for Qualcomm QSD/MSM on-chip EHCI USB controller"
Florian Fainelli42443dc2013-04-09 14:29:27 +0200186 depends on ARCH_MSM
Pavankumar Kondetib0848ae2010-12-07 17:53:56 +0530187 select USB_EHCI_ROOT_HUB_TT
Pavankumar Kondetidfb21302011-03-04 22:45:02 +0530188 select USB_MSM_OTG
Pavankumar Kondetib0848ae2010-12-07 17:53:56 +0530189 ---help---
190 Enables support for the USB Host controller present on the
191 Qualcomm chipsets. Root Hub has inbuilt TT.
192 This driver depends on OTG driver for PHY initialization,
Pavankumar Kondeti8bb6a162010-12-07 17:53:57 +0530193 clock management, powering up VBUS, and power management.
Pavankumar Kondeti8cf28f12011-02-04 10:08:18 +0530194 This driver is not supported on boards like trout which
195 has an external PHY.
Pavankumar Kondetib0848ae2010-12-07 17:53:56 +0530196
Benoit Goby79ad3b52011-03-09 16:28:56 -0800197config USB_EHCI_TEGRA
Manjunath Goudar9fc5f242013-06-13 11:24:12 -0600198 tristate "NVIDIA Tegra HCD support"
Florian Fainelli42443dc2013-04-09 14:29:27 +0200199 depends on ARCH_TEGRA
Benoit Goby79ad3b52011-03-09 16:28:56 -0800200 select USB_EHCI_ROOT_HUB_TT
Felipe Balbi75f32ec2013-03-20 14:18:28 +0200201 select USB_PHY
Benoit Goby79ad3b52011-03-09 16:28:56 -0800202 help
203 This driver enables support for the internal USB Host Controllers
204 found in NVIDIA Tegra SoCs. The controllers are EHCI compliant.
205
Valentine Barshakda0e8fb2007-12-30 15:28:50 -0800206config USB_EHCI_HCD_PPC_OF
207 bool "EHCI support for PPC USB controller on OF platform bus"
Florian Fainelli42443dc2013-04-09 14:29:27 +0200208 depends on PPC_OF
Valentine Barshakda0e8fb2007-12-30 15:28:50 -0800209 default y
210 ---help---
211 Enables support for the USB controller present on the PowerPC
212 OpenFirmware platform bus.
213
Yoshihiro Shimoda60b0bf02011-03-01 16:58:37 +0900214config USB_EHCI_SH
215 bool "EHCI support for SuperH USB controller"
Florian Fainelli42443dc2013-04-09 14:29:27 +0200216 depends on SUPERH
Yoshihiro Shimoda60b0bf02011-03-01 16:58:37 +0900217 ---help---
218 Enables support for the on-chip EHCI controller on the SuperH.
219 If you use the PCI EHCI controller, this option is not necessary.
220
Joonyoung Shim1bcc5aa2011-04-08 14:08:50 +0900221config USB_EHCI_S5P
Manjunath Goudar7edb3da2013-04-02 18:24:01 +0200222 tristate "EHCI support for Samsung S5P/EXYNOS SoC Series"
Tomasz Figa58d5b722013-06-19 01:25:48 +0900223 depends on PLAT_S5P || ARCH_EXYNOS
Greg Kroah-Hartmane9a92b22013-02-20 10:25:05 -0800224 help
Manjunath Goudar7edb3da2013-04-02 18:24:01 +0200225 Enable support for the Samsung S5Pxxxx and Exynos3/4/5 SOC's
226 on-chip EHCI controller.
Joonyoung Shim1bcc5aa2011-04-08 14:08:50 +0900227
Neil Zhang3a082ec2011-12-20 13:20:23 +0800228config USB_EHCI_MV
Manjunath Goudara76dd462013-04-02 18:23:59 +0200229 bool "EHCI support for Marvell PXA/MMP USB controller"
Florian Fainelli42443dc2013-04-09 14:29:27 +0200230 depends on (ARCH_PXA || ARCH_MMP)
Neil Zhang3a082ec2011-12-20 13:20:23 +0800231 select USB_EHCI_ROOT_HUB_TT
232 ---help---
233 Enables support for Marvell (including PXA and MMP series) on-chip
234 USB SPH and OTG controller. SPH is a single port host, and it can
235 only be EHCI host. OTG is controller that can switch to host mode.
Manjunath Goudara76dd462013-04-02 18:23:59 +0200236 Note that this driver will not work on Marvell's other EHCI
237 controller used by the EBU-type SoCs including Orion, Kirkwood,
238 Dova, Armada 370 and Armada XP. See "Support for Marvell EBU
239 on-chip EHCI USB controller" for those.
Neil Zhang3a082ec2011-12-20 13:20:23 +0800240
Wan ZongShun586dfc82009-06-13 09:14:28 +0800241config USB_W90X900_EHCI
242 bool "W90X900(W90P910) EHCI support"
Florian Fainelli42443dc2013-04-09 14:29:27 +0200243 depends on ARCH_W90X900
Wan ZongShun586dfc82009-06-13 09:14:28 +0800244 ---help---
245 Enables support for the W90X900 USB controller
246
Mac Lin760efe62010-11-25 23:58:00 +0800247config USB_CNS3XXX_EHCI
Florian Fainellif3a958d2012-10-08 15:11:25 +0200248 bool "Cavium CNS3XXX EHCI Module (DEPRECATED)"
Florian Fainelli42443dc2013-04-09 14:29:27 +0200249 depends on ARCH_CNS3XXX
Florian Fainellif3a958d2012-10-08 15:11:25 +0200250 select USB_EHCI_HCD_PLATFORM
Mac Lin760efe62010-11-25 23:58:00 +0800251 ---help---
Florian Fainellif3a958d2012-10-08 15:11:25 +0200252 This option is deprecated now and the driver was removed, use
253 USB_EHCI_HCD_PLATFORM instead.
254
Mac Lin760efe62010-11-25 23:58:00 +0800255 Enable support for the CNS3XXX SOC's on-chip EHCI controller.
256 It is needed for high-speed (480Mbit/sec) USB 2.0 device
257 support.
258
Gabor Juhos502fa842011-04-13 10:54:22 +0200259config USB_EHCI_ATH79
Hauke Mehrtens5d98cd42012-03-13 01:04:53 +0100260 bool "EHCI support for AR7XXX/AR9XXX SoCs (DEPRECATED)"
Florian Fainelli42443dc2013-04-09 14:29:27 +0200261 depends on (SOC_AR71XX || SOC_AR724X || SOC_AR913X || SOC_AR933X)
Gabor Juhos502fa842011-04-13 10:54:22 +0200262 select USB_EHCI_ROOT_HUB_TT
Hauke Mehrtens5d98cd42012-03-13 01:04:53 +0100263 select USB_EHCI_HCD_PLATFORM
Gabor Juhos502fa842011-04-13 10:54:22 +0200264 default y
265 ---help---
Hauke Mehrtens5d98cd42012-03-13 01:04:53 +0100266 This option is deprecated now and the driver was removed, use
267 USB_EHCI_HCD_PLATFORM instead.
268
Gabor Juhos502fa842011-04-13 10:54:22 +0200269 Enables support for the built-in EHCI controller present
270 on the Atheros AR7XXX/AR9XXX SoCs.
271
Florian Fainelli42443dc2013-04-09 14:29:27 +0200272config USB_EHCI_HCD_PLATFORM
273 tristate "Generic EHCI driver for a platform device"
274 default n
275 ---help---
276 Adds an EHCI host driver for a generic platform device, which
277 provides a memory space and an irq.
278
279 If unsure, say N.
280
281config USB_OCTEON_EHCI
282 bool "Octeon on-chip EHCI support"
David Daney9ddebc42013-05-22 15:10:46 +0000283 depends on CAVIUM_OCTEON_SOC
Florian Fainelli42443dc2013-04-09 14:29:27 +0200284 default n
285 select USB_EHCI_BIG_ENDIAN_MMIO
286 help
287 Enable support for the Octeon II SOC's on-chip EHCI
288 controller. It is needed for high-speed (480Mbit/sec)
289 USB 2.0 device support. All CN6XXX based chips with USB are
290 supported.
291
292endif # USB_EHCI_HCD
293
Rodolfo Giomettib92a78e2008-10-23 10:08:07 +0200294config USB_OXU210HP_HCD
295 tristate "OXU210HP HCD support"
Florian Fainelli25e11ec2013-04-09 14:29:25 +0200296 depends on GENERIC_HARDIRQS
Rodolfo Giomettib92a78e2008-10-23 10:08:07 +0200297 ---help---
298 The OXU210HP is an USB host/OTG/device controller. Enable this
299 option if your board has this chip. If unsure, say N.
300
301 This driver does not support isochronous transfers and doesn't
302 implement OTG nor USB device controllers.
303
304 To compile this driver as a module, choose M here: the
305 module will be called oxu210hp-hcd.
306
Olav Kongas4808a1c2005-04-09 22:57:39 +0300307config USB_ISP116X_HCD
308 tristate "ISP116X HCD support"
Olav Kongas4808a1c2005-04-09 22:57:39 +0300309 ---help---
310 The ISP1160 and ISP1161 chips are USB host controllers. Enable this
311 option if your board has this chip. If unsure, say N.
312
313 This driver does not support isochronous transfers.
314
315 To compile this driver as a module, choose M here: the
316 module will be called isp116x-hcd.
317
Sebastian Siewiordb11e472008-04-24 00:37:04 +0200318config USB_ISP1760_HCD
319 tristate "ISP 1760 HCD support"
Sebastian Siewiordb11e472008-04-24 00:37:04 +0200320 ---help---
321 The ISP1760 chip is a USB 2.0 host controller.
322
323 This driver does not support isochronous transfers or OTG.
Sebastian Andrzej Siewiorff30bf12008-11-02 15:25:42 +0100324 This USB controller is usually attached to a non-DMA-Master
325 capable bus. NXP's eval kit brings this chip on PCI card
326 where the chip itself is behind a PLB to simulate such
327 a bus.
Sebastian Siewiordb11e472008-04-24 00:37:04 +0200328
329 To compile this driver as a module, choose M here: the
Sebastian Andrzej Siewiorff30bf12008-11-02 15:25:42 +0100330 module will be called isp1760.
Sebastian Siewiordb11e472008-04-24 00:37:04 +0200331
Lothar Wassmanna9d43092009-07-16 20:51:21 -0400332config USB_ISP1362_HCD
333 tristate "ISP1362 HCD support"
Lothar Wassmanna9d43092009-07-16 20:51:21 -0400334 default N
335 ---help---
336 Supports the Philips ISP1362 chip as a host controller
337
338 This driver does not support isochronous transfers.
339
340 To compile this driver as a module, choose M here: the
341 module will be called isp1362-hcd.
342
Yuan-Hsin Chen6c920bfb2013-05-17 10:14:14 +0000343config USB_FUSBH200_HCD
344 tristate "FUSBH200 HCD support"
345 depends on USB
346 default N
347 ---help---
348 Faraday FUSBH200 is designed to meet USB2.0 EHCI specification
349 with minor modification.
350
351 To compile this driver as a module, choose M here: the
352 module will be called fusbh200-hcd.
353
Linus Torvalds1da177e2005-04-16 15:20:36 -0700354config USB_OHCI_HCD
Manjunath Goudarc1117af2013-05-28 18:34:51 +0530355 tristate "OHCI HCD (USB 1.1) support"
Linus Torvalds1da177e2005-04-16 15:20:36 -0700356 select ISP1301_OMAP if MACH_OMAP_H2 || MACH_OMAP_H3
Linus Torvalds61464c82012-10-01 18:19:05 -0700357 depends on USB_ISP1301 || !ARCH_LPC32XX
Linus Torvalds1da177e2005-04-16 15:20:36 -0700358 ---help---
359 The Open Host Controller Interface (OHCI) is a standard for accessing
360 USB 1.1 host controller hardware. It does more in hardware than Intel's
361 UHCI specification. If your USB host controller follows the OHCI spec,
362 say Y. On most non-x86 systems, and on x86 hardware that's not using a
363 USB controller from Intel or VIA, this is appropriate. If your host
364 controller doesn't use PCI, this is probably appropriate. For a PCI
365 based system where you're not sure, the "lspci -v" entry will list the
366 right "prog-if" for your USB controller(s): EHCI, OHCI, or UHCI.
367
368 To compile this driver as a module, choose M here: the
369 module will be called ohci-hcd.
370
Florian Fainelli3ad3ca02013-04-09 14:29:28 +0200371if USB_OHCI_HCD
372
Anand Gadiyar968b4482010-05-10 21:56:12 +0530373config USB_OHCI_HCD_OMAP1
374 bool "OHCI support for OMAP1/2 chips"
Florian Fainelli3ad3ca02013-04-09 14:29:28 +0200375 depends on ARCH_OMAP1
Anand Gadiyar968b4482010-05-10 21:56:12 +0530376 default y
377 ---help---
378 Enables support for the OHCI controller on OMAP1/2 chips.
379
380config USB_OHCI_HCD_OMAP3
381 bool "OHCI support for OMAP3 and later chips"
Florian Fainelli3ad3ca02013-04-09 14:29:28 +0200382 depends on (ARCH_OMAP3 || ARCH_OMAP4)
Anand Gadiyar968b4482010-05-10 21:56:12 +0530383 default y
384 ---help---
385 Enables support for the on-chip OHCI controller on
386 OMAP3 and later chips.
387
Gabor Juhos90e6ca52011-04-13 10:54:24 +0200388config USB_OHCI_ATH79
Hauke Mehrtens5d98cd42012-03-13 01:04:53 +0100389 bool "USB OHCI support for the Atheros AR71XX/AR7240 SoCs (DEPRECATED)"
Florian Fainelli3ad3ca02013-04-09 14:29:28 +0200390 depends on (SOC_AR71XX || SOC_AR724X)
Hauke Mehrtens5d98cd42012-03-13 01:04:53 +0100391 select USB_OHCI_HCD_PLATFORM
Gabor Juhos90e6ca52011-04-13 10:54:24 +0200392 default y
393 help
Hauke Mehrtens5d98cd42012-03-13 01:04:53 +0100394 This option is deprecated now and the driver was removed, use
395 USB_OHCI_HCD_PLATFORM instead.
396
Gabor Juhos90e6ca52011-04-13 10:54:24 +0200397 Enables support for the built-in OHCI controller present on the
398 Atheros AR71XX/AR7240 SoCs.
399
Sylvain Munaut495a6782006-12-13 21:09:55 +0100400config USB_OHCI_HCD_PPC_OF_BE
Arnd Bergmann45e83882009-06-19 05:35:34 -0700401 bool "OHCI support for OF platform bus (big endian)"
Florian Fainelli3ad3ca02013-04-09 14:29:28 +0200402 depends on PPC_OF
Sylvain Munaut495a6782006-12-13 21:09:55 +0100403 select USB_OHCI_BIG_ENDIAN_DESC
404 select USB_OHCI_BIG_ENDIAN_MMIO
Arnd Bergmann45e83882009-06-19 05:35:34 -0700405 ---help---
406 Enables support for big-endian USB controllers present on the
407 OpenFirmware platform bus.
Sylvain Munaut495a6782006-12-13 21:09:55 +0100408
409config USB_OHCI_HCD_PPC_OF_LE
Arnd Bergmann45e83882009-06-19 05:35:34 -0700410 bool "OHCI support for OF platform bus (little endian)"
Florian Fainelli3ad3ca02013-04-09 14:29:28 +0200411 depends on PPC_OF
Sylvain Munaut495a6782006-12-13 21:09:55 +0100412 select USB_OHCI_LITTLE_ENDIAN
Arnd Bergmann45e83882009-06-19 05:35:34 -0700413 ---help---
414 Enables support for little-endian USB controllers present on the
415 OpenFirmware platform bus.
416
417config USB_OHCI_HCD_PPC_OF
418 bool
Florian Fainelli3ad3ca02013-04-09 14:29:28 +0200419 depends on PPC_OF
Arnd Bergmann45e83882009-06-19 05:35:34 -0700420 default USB_OHCI_HCD_PPC_OF_BE || USB_OHCI_HCD_PPC_OF_LE
Sylvain Munaut495a6782006-12-13 21:09:55 +0100421
Linus Torvalds1da177e2005-04-16 15:20:36 -0700422config USB_OHCI_HCD_PCI
Manjunath Goudarc1117af2013-05-28 18:34:51 +0530423 tristate "OHCI support for PCI-bus USB controllers"
424 depends on PCI
Linus Torvalds1da177e2005-04-16 15:20:36 -0700425 default y
426 select USB_OHCI_LITTLE_ENDIAN
427 ---help---
428 Enables support for PCI-bus plug-in USB controller cards.
429 If unsure, say Y.
430
Michael Bueschc604e852007-10-09 23:47:17 -0700431config USB_OHCI_HCD_SSB
Hauke Mehrtens259b83a2012-03-15 23:49:59 +0100432 bool "OHCI support for Broadcom SSB OHCI core (DEPRECATED)"
Florian Fainelli3ad3ca02013-04-09 14:29:28 +0200433 depends on (SSB = y || SSB = USB_OHCI_HCD)
Hauke Mehrtens259b83a2012-03-15 23:49:59 +0100434 select USB_HCD_SSB
435 select USB_OHCI_HCD_PLATFORM
Michael Bueschc604e852007-10-09 23:47:17 -0700436 default n
437 ---help---
Hauke Mehrtens259b83a2012-03-15 23:49:59 +0100438 This option is deprecated now and the driver was removed, use
439 USB_HCD_SSB and USB_OHCI_HCD_PLATFORM instead.
440
Michael Bueschc604e852007-10-09 23:47:17 -0700441 Support for the Sonics Silicon Backplane (SSB) attached
442 Broadcom USB OHCI core.
443
444 This device is present in some embedded devices with
445 Broadcom based SSB bus.
446
447 If unsure, say N.
448
Yoshihiro Shimoda60b0bf02011-03-01 16:58:37 +0900449config USB_OHCI_SH
Florian Fainelli231a72e2012-10-08 15:11:37 +0200450 bool "OHCI support for SuperH USB controller (DEPRECATED)"
Florian Fainelli3ad3ca02013-04-09 14:29:28 +0200451 depends on SUPERH
Florian Fainelli231a72e2012-10-08 15:11:37 +0200452 select USB_OHCI_HCD_PLATFORM
Yoshihiro Shimoda60b0bf02011-03-01 16:58:37 +0900453 ---help---
Florian Fainelli231a72e2012-10-08 15:11:37 +0200454 This option is deprecated now and the driver was removed, use
455 USB_OHCI_HCD_PLATFORM instead.
456
Yoshihiro Shimoda60b0bf02011-03-01 16:58:37 +0900457 Enables support for the on-chip OHCI controller on the SuperH.
458 If you use the PCI OHCI controller, this option is not necessary.
459
Jingoo Han62194242011-12-23 11:20:54 +0900460config USB_OHCI_EXYNOS
461 boolean "OHCI support for Samsung EXYNOS SoC Series"
Florian Fainelli3ad3ca02013-04-09 14:29:28 +0200462 depends on ARCH_EXYNOS
Jingoo Han62194242011-12-23 11:20:54 +0900463 help
464 Enable support for the Samsung Exynos SOC's on-chip OHCI controller.
465
Mac Lin760efe62010-11-25 23:58:00 +0800466config USB_CNS3XXX_OHCI
Florian Fainellic23920b02012-10-08 15:11:33 +0200467 bool "Cavium CNS3XXX OHCI Module (DEPRECATED)"
Florian Fainelli3ad3ca02013-04-09 14:29:28 +0200468 depends on ARCH_CNS3XXX
Florian Fainellic23920b02012-10-08 15:11:33 +0200469 select USB_OHCI_HCD_PLATFORM
Mac Lin760efe62010-11-25 23:58:00 +0800470 ---help---
Florian Fainellic23920b02012-10-08 15:11:33 +0200471 This option is deprecated now and the driver was removed, use
472 USB_OHCI_HCD_PLATFORM instead.
473
Mac Lin760efe62010-11-25 23:58:00 +0800474 Enable support for the CNS3XXX SOC's on-chip OHCI controller.
475 It is needed for low-speed USB 1.0 device support.
476
Hauke Mehrtensfa3364b2012-03-13 01:04:47 +0100477config USB_OHCI_HCD_PLATFORM
Manjunath Goudar928fb682013-06-03 20:46:08 +0530478 tristate "Generic OHCI driver for a platform device"
Hauke Mehrtensfa3364b2012-03-13 01:04:47 +0100479 default n
480 ---help---
481 Adds an OHCI host driver for a generic platform device, which
Peter Meerwald898d8282012-08-18 15:53:12 +0200482 provides a memory space and an irq.
Hauke Mehrtensfa3364b2012-03-13 01:04:47 +0100483
484 If unsure, say N.
485
Florian Fainelli3ad3ca02013-04-09 14:29:28 +0200486config USB_OCTEON_OHCI
487 bool "Octeon on-chip OHCI support"
David Daney9ddebc42013-05-22 15:10:46 +0000488 depends on CAVIUM_OCTEON_SOC
Florian Fainelli3ad3ca02013-04-09 14:29:28 +0200489 default USB_OCTEON_EHCI
490 select USB_OHCI_BIG_ENDIAN_MMIO
491 select USB_OHCI_LITTLE_ENDIAN
492 help
493 Enable support for the Octeon II SOC's on-chip OHCI
494 controller. It is needed for low-speed USB 1.0 device
495 support. All CN6XXX based chips with USB are supported.
496
Hauke Mehrtens7a7a4a592012-03-13 01:04:48 +0100497
Benjamin Herrenschmidt11d1a4a2006-12-15 06:54:03 +1100498config USB_OHCI_BIG_ENDIAN_DESC
499 bool
Benjamin Herrenschmidt11d1a4a2006-12-15 06:54:03 +1100500 default n
501
502config USB_OHCI_BIG_ENDIAN_MMIO
Linus Torvalds1da177e2005-04-16 15:20:36 -0700503 bool
Linus Torvalds1da177e2005-04-16 15:20:36 -0700504 default n
505
506config USB_OHCI_LITTLE_ENDIAN
507 bool
Linus Torvalds1da177e2005-04-16 15:20:36 -0700508 default n if STB03xxx || PPC_MPC52xx
509 default y
510
Florian Fainelli3ad3ca02013-04-09 14:29:28 +0200511endif # USB_OHCI_HCD
512
Linus Torvalds1da177e2005-04-16 15:20:36 -0700513config USB_UHCI_HCD
514 tristate "UHCI HCD (most Intel and VIA) support"
Alan Sternccd95092013-05-14 13:54:12 -0400515 depends on PCI || USB_UHCI_SUPPORT_NON_PCI_HC
Linus Torvalds1da177e2005-04-16 15:20:36 -0700516 ---help---
517 The Universal Host Controller Interface is a standard by Intel for
518 accessing the USB hardware in the PC (which is also called the USB
519 host controller). If your USB host controller conforms to this
520 standard, you may want to say Y, but see below. All recent boards
521 with Intel PCI chipsets (like intel 430TX, 440FX, 440LX, 440BX,
522 i810, i820) conform to this standard. Also all VIA PCI chipsets
523 (like VIA VP2, VP3, MVP3, Apollo Pro, Apollo Pro II or Apollo Pro
Jan Andersson3db77392011-05-06 12:00:18 +0200524 133) and LEON/GRLIB SoCs with the GRUSBHC controller.
525 If unsure, say Y.
Linus Torvalds1da177e2005-04-16 15:20:36 -0700526
527 To compile this driver as a module, choose M here: the
528 module will be called uhci-hcd.
529
Jan Anderssond3219d12011-05-06 12:00:17 +0200530config USB_UHCI_SUPPORT_NON_PCI_HC
531 bool
Alan Sternccd95092013-05-14 13:54:12 -0400532 default y if (SPARC_LEON || USB_UHCI_PLATFORM)
Tony Prisk100d4592012-07-21 22:58:53 +1200533
534config USB_UHCI_PLATFORM
Alan Sternccd95092013-05-14 13:54:12 -0400535 bool
Tony Prisk100d4592012-07-21 22:58:53 +1200536 default y if ARCH_VT8500
Jan Anderssond3219d12011-05-06 12:00:17 +0200537
Jan Andersson8452c672011-05-18 10:44:49 +0200538config USB_UHCI_BIG_ENDIAN_MMIO
539 bool
Alan Sternccd95092013-05-14 13:54:12 -0400540 default y if SPARC_LEON
Jan Andersson8452c672011-05-18 10:44:49 +0200541
Jan Andersson51e2f622011-05-18 10:44:51 +0200542config USB_UHCI_BIG_ENDIAN_DESC
543 bool
Alan Sternccd95092013-05-14 13:54:12 -0400544 default y if SPARC_LEON
Jan Andersson51e2f622011-05-18 10:44:51 +0200545
Anton Vorontsov236dd4d2009-01-10 05:03:21 +0300546config USB_FHCI_HCD
547 tristate "Freescale QE USB Host Controller support"
Florian Fainelli25e11ec2013-04-09 14:29:25 +0200548 depends on OF_GPIO && QE_GPIO && QUICC_ENGINE
Anton Vorontsov236dd4d2009-01-10 05:03:21 +0300549 select FSL_GTM
550 select QE_USB
551 help
552 This driver enables support for Freescale QE USB Host Controller
553 (as found on MPC8360 and MPC8323 processors), the driver supports
554 Full and Low Speed USB.
555
556config FHCI_DEBUG
557 bool "Freescale QE USB Host Controller debug support"
558 depends on USB_FHCI_HCD && DEBUG_FS
559 help
560 Say "y" to see some FHCI debug information and statistics
Lucas De Marchi25985ed2011-03-30 22:57:33 -0300561 through debugfs.
Anton Vorontsov236dd4d2009-01-10 05:03:21 +0300562
Tony Olechd774efe2006-09-13 11:27:35 +0100563config USB_U132_HCD
564 tristate "Elan U132 Adapter Host Controller"
Florian Fainelli25e11ec2013-04-09 14:29:25 +0200565 depends on USB_FTDI_ELAN
Tony Olechd774efe2006-09-13 11:27:35 +0100566 default M
567 help
568 The U132 adapter is a USB to CardBus adapter specifically designed
569 for PC cards that contain an OHCI host controller. Typical PC cards
570 are the Orange Mobile 3G Option GlobeTrotter Fusion card. The U132
571 adapter will *NOT* work with PC cards that do not contain an OHCI
572 controller.
573
Matt LaPlante3cb2fcc2006-11-30 05:22:59 +0100574 For those PC cards that contain multiple OHCI controllers only the
Tony Olechd774efe2006-09-13 11:27:35 +0100575 first one is used.
576
577 The driver consists of two modules, the "ftdi-elan" module is a
578 USB client driver that interfaces to the FTDI chip within ELAN's
579 USB-to-PCMCIA adapter, and this "u132-hcd" module is a USB host
580 controller driver that talks to the OHCI controller within the
581 CardBus cards that are inserted in the U132 adapter.
582
583 This driver has been tested with a CardBus OHCI USB adapter, and
584 worked with a USB PEN Drive inserted into the first USB port of
585 the PCCARD. A rather pointless thing to do, but useful for testing.
586
587 It is safe to say M here.
588
589 See also <http://www.elandigitalsystems.com/support/ufaq/u132linux.php>
590
Linus Torvalds1da177e2005-04-16 15:20:36 -0700591config USB_SL811_HCD
592 tristate "SL811HS HCD support"
Linus Torvalds1da177e2005-04-16 15:20:36 -0700593 help
594 The SL811HS is a single-port USB controller that supports either
595 host side or peripheral side roles. Enable this option if your
596 board has this chip, and you want to use it as a host controller.
597 If unsure, say N.
598
599 To compile this driver as a module, choose M here: the
600 module will be called sl811-hcd.
601
Mike Frysingerad7c56f2011-03-22 15:35:39 -0400602config USB_SL811_HCD_ISO
603 bool "partial ISO support"
604 depends on USB_SL811_HCD
605 help
606 The driver doesn't support iso_frame_desc (yet), but for some simple
607 devices that just queue one ISO frame per URB, then ISO transfers
608 "should" work using the normal urb status fields.
609
610 If unsure, say N.
611
David Brownellc6de2b62005-05-26 05:55:55 -0700612config USB_SL811_CS
613 tristate "CF/PCMCIA support for SL811HS HCD"
614 depends on USB_SL811_HCD && PCMCIA
David Brownellc6de2b62005-05-26 05:55:55 -0700615 help
616 Wraps a PCMCIA driver around the SL811HS HCD, supporting the RATOC
617 REX-CFU1U CF card (often used with PDAs). If unsure, say N.
618
619 To compile this driver as a module, choose M here: the
620 module will be called "sl811_cs".
621
Yoshihiro Shimoda5d304352007-05-10 13:18:19 +0900622config USB_R8A66597_HCD
M4rkusXXLfa0de2b2007-08-10 14:53:32 -0700623 tristate "R8A66597 HCD support"
Yoshihiro Shimoda5d304352007-05-10 13:18:19 +0900624 help
625 The R8A66597 is a USB 2.0 host and peripheral controller.
626
627 Enable this option if your board has this chip, and you want
628 to use it as a host controller. If unsure, say N.
629
630 To compile this driver as a module, choose M here: the
631 module will be called r8a66597-hcd.
632
Kuninori Morimoto034d7c12011-10-10 22:07:40 -0700633config USB_RENESAS_USBHS_HCD
634 tristate "Renesas USBHS HCD support"
Kuninori Morimoto034d7c12011-10-10 22:07:40 -0700635 depends on USB_RENESAS_USBHS
636 help
637 The Renesas USBHS is a USB 2.0 host and peripheral controller.
638
639 Enable this option if your board has this chip, and you want
640 to use it as a host controller. If unsure, say N.
641
642 To compile this driver as a module, choose M here: the
643 module will be called renesas-usbhs.
644
David Vrabel7e6133a2008-09-17 16:34:28 +0100645config USB_WHCI_HCD
Greg Kroah-Hartmaneb83be92012-09-14 21:15:50 -0700646 tristate "Wireless USB Host Controller Interface (WHCI) driver"
Randy Dunlap36f8ecb2012-01-27 15:47:03 -0800647 depends on PCI && USB && UWB
David Vrabel7e6133a2008-09-17 16:34:28 +0100648 select USB_WUSB
649 select UWB_WHCI
650 help
651 A driver for PCI-based Wireless USB Host Controllers that are
652 compliant with the WHCI specification.
653
654 To compile this driver a module, choose M here: the module
655 will be called "whci-hcd".
Inaky Perez-Gonzalezd09318b2008-09-17 16:34:30 +0100656
657config USB_HWA_HCD
Greg Kroah-Hartmaneb83be92012-09-14 21:15:50 -0700658 tristate "Host Wire Adapter (HWA) driver"
Florian Fainelli25e11ec2013-04-09 14:29:25 +0200659 depends on UWB
Inaky Perez-Gonzalezd09318b2008-09-17 16:34:30 +0100660 select USB_WUSB
661 select UWB_HWA
662 help
663 This driver enables you to connect Wireless USB devices to
664 your system using a Host Wire Adaptor USB dongle. This is an
665 UWB Radio Controller and WUSB Host Controller connected to
666 your machine via USB (specified in WUSB1.0).
667
668 To compile this driver a module, choose M here: the module
669 will be called "hwa-hc".
Martin Fuzzey23d3e7a2009-11-21 12:14:48 +0100670
671config USB_IMX21_HCD
Sascha Hauer5de9ec42011-08-24 08:41:10 +0200672 tristate "i.MX21 HCD support"
Florian Fainelli25e11ec2013-04-09 14:29:25 +0200673 depends on ARM && ARCH_MXC
Martin Fuzzey23d3e7a2009-11-21 12:14:48 +0100674 help
675 This driver enables support for the on-chip USB host in the
Sascha Hauer5de9ec42011-08-24 08:41:10 +0200676 i.MX21 processor.
Martin Fuzzey23d3e7a2009-11-21 12:14:48 +0100677
678 To compile this driver as a module, choose M here: the
679 module will be called "imx21-hcd".
680
David Daney1643acc2010-10-08 14:47:52 -0700681
David Daney1643acc2010-10-08 14:47:52 -0700682
683config USB_OCTEON2_COMMON
684 bool
685 default y if USB_OCTEON_EHCI || USB_OCTEON_OHCI
Hauke Mehrtens62e11d12012-03-15 23:49:57 +0100686
687config USB_HCD_BCMA
688 tristate "BCMA usb host driver"
Greg Kroah-Hartmaneb83be92012-09-14 21:15:50 -0700689 depends on BCMA
Hauke Mehrtens62e11d12012-03-15 23:49:57 +0100690 select USB_OHCI_HCD_PLATFORM if USB_OHCI_HCD
691 select USB_EHCI_HCD_PLATFORM if USB_EHCI_HCD
692 help
Jesper Dangaard Brouer71c421d2012-06-15 12:01:33 +0200693 Enable support for the EHCI and OCHI host controller on an bcma bus.
Hauke Mehrtens62e11d12012-03-15 23:49:57 +0100694 It converts the bcma driver into two platform device drivers
695 for ehci and ohci.
696
697 If unsure, say N.
Hauke Mehrtens7043c2c2012-03-15 23:49:58 +0100698
699config USB_HCD_SSB
700 tristate "SSB usb host driver"
Greg Kroah-Hartmaneb83be92012-09-14 21:15:50 -0700701 depends on SSB
Hauke Mehrtens7043c2c2012-03-15 23:49:58 +0100702 select USB_OHCI_HCD_PLATFORM if USB_OHCI_HCD
703 select USB_EHCI_HCD_PLATFORM if USB_EHCI_HCD
704 help
Jesper Dangaard Brouer71c421d2012-06-15 12:01:33 +0200705 Enable support for the EHCI and OCHI host controller on an bcma bus.
Hauke Mehrtens7043c2c2012-03-15 23:49:58 +0100706 It converts the bcma driver into two platform device drivers
707 for ehci and ohci.
708
709 If unsure, say N.