arch/arm/mach-omap2/board-zoom3.c

/*
 * Copyright (C) 2009 Texas Instruments Inc.
 *
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License version 2 as
 * published by the Free Software Foundation.
 */

#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/input.h>
#include <linux/gpio.h>

#include <asm/mach-types.h>
#include <asm/mach/arch.h>

#include <mach/board-zoom.h>

#include <plat/common.h>
#include <plat/board.h>
#include <plat/usb.h>

#include "mux.h"
#include "sdram-hynix-h8mbx00u0mer-0em.h"

static void __init omap_zoom_map_io(void)
{
	omap2_set_globals_36xx();
	omap34xx_map_common_io();
}

static struct omap_board_config_kernel zoom_config[] __initdata = {
};

static void __init omap_zoom_init_irq(void)
{
	omap_board_config = zoom_config;
	omap_board_config_size = ARRAY_SIZE(zoom_config);
	omap2_init_common_hw(h8mbx00u0mer0em_sdrc_params,
			h8mbx00u0mer0em_sdrc_params);
	omap_init_irq();
	omap_gpio_init();
}

#ifdef CONFIG_OMAP_MUX
static struct omap_board_mux board_mux[] __initdata = {
	/* WLAN IRQ - GPIO 162 */
	OMAP3_MUX(MCBSP1_CLKX, OMAP_MUX_MODE4 | OMAP_PIN_INPUT_PULLUP),
	/* WLAN POWER ENABLE - GPIO 101 */
	OMAP3_MUX(CAM_D2, OMAP_MUX_MODE4 | OMAP_PIN_OUTPUT),
	/* WLAN SDIO: MMC3 CMD */
	OMAP3_MUX(MCSPI1_CS1, OMAP_MUX_MODE3 | OMAP_PIN_INPUT_PULLUP),
	/* WLAN SDIO: MMC3 CLK */
	OMAP3_MUX(ETK_CLK, OMAP_MUX_MODE2 | OMAP_PIN_INPUT_PULLUP),
	/* WLAN SDIO: MMC3 DAT[0-3] */
	OMAP3_MUX(ETK_D3, OMAP_MUX_MODE2 | OMAP_PIN_INPUT_PULLUP),
	OMAP3_MUX(ETK_D4, OMAP_MUX_MODE2 | OMAP_PIN_INPUT_PULLUP),
	OMAP3_MUX(ETK_D5, OMAP_MUX_MODE2 | OMAP_PIN_INPUT_PULLUP),
	OMAP3_MUX(ETK_D6, OMAP_MUX_MODE2 | OMAP_PIN_INPUT_PULLUP),
	{ .reg_offset = OMAP_MUX_TERMINATOR },
};
#else
#define board_mux	NULL
#endif

static const struct ehci_hcd_omap_platform_data ehci_pdata __initconst = {
	.port_mode[0]		= EHCI_HCD_OMAP_MODE_UNKNOWN,
	.port_mode[1]		= EHCI_HCD_OMAP_MODE_PHY,
	.port_mode[2]		= EHCI_HCD_OMAP_MODE_UNKNOWN,
	.phy_reset		= true,
	.reset_gpio_port[0]	= -EINVAL,
	.reset_gpio_port[1]	= 64,
	.reset_gpio_port[2]	= -EINVAL,
};

static void __init omap_zoom_init(void)
{
	omap3_mux_init(board_mux, OMAP_PACKAGE_CBP);
	zoom_peripherals_init();
	zoom_debugboard_init();

	omap_mux_init_gpio(64, OMAP_PIN_OUTPUT);
	usb_ehci_init(&ehci_pdata);
}

MACHINE_START(OMAP_ZOOM3, "OMAP Zoom3 board")
	.phys_io	= ZOOM_UART_BASE,
	.io_pg_offst	= (ZOOM_UART_VIRT >> 18) & 0xfffc,
	.boot_params	= 0x80000100,
	.map_io		= omap_zoom_map_io,
	.init_irq	= omap_zoom_init_irq,
	.init_machine	= omap_zoom_init,
	.timer		= &omap_timer,
MACHINE_END