| #include <dt-bindings/gpio/gpio.h> |
| &soc { |
| timer { |
| clock-frequency = <500000>; |
| }; |
| |
| timer@f420000 { |
| clock-frequency = <500000>; |
| }; |
| |
| wdog { |
| status = "disabled"; |
| }; |
| |
| usb_emu_phy_0: usb_emu_phy@0x04f20000 { |
| compatible = "qcom,usb-emu-phy"; |
| reg = <0x04f20000 0x9500>; |
| |
| qcom,emu-init-seq = <0xffff 0x4 |
| 0xfff0 0x4 |
| 0x100000 0x20 |
| 0x0 0x20 |
| 0x101f0 0x20 |
| 0x100000 0x3c |
| 0x0 0x3c |
| 0x10060 0x3c |
| 0x0 0x4>; |
| }; |
| }; |
| |
| &tsens0 { |
| status = "disabled"; |
| }; |
| |
| &tsens1 { |
| status = "disabled"; |
| }; |
| |
| &usb0 { |
| dpdm-supply = <&usb_nop_phy>; |
| dwc3@4e00000 { |
| usb-phy = <&usb_emu_phy_0>, <&usb_nop_phy>; |
| maximum-speed = "high-speed"; |
| dr_mode = "peripheral"; |
| }; |
| }; |
| |
| &sdhc_1 { |
| status = "disabled"; |
| |
| pinctrl-names = "default", "sleep"; |
| pinctrl-0 = <&sdc1_on>; |
| pinctrl-1 = <&sdc1_off>; |
| |
| cap-mmc-highspeed; |
| |
| vdd-supply = <&L7E>; |
| qcom,vdd-voltage-level = <2960000 2960000>; |
| qcom,vdd-current-level = <0 570000>; |
| |
| vdd-io-supply = <&L12A>; |
| qcom,vdd-io-always-on; |
| qcom,vdd-io-lpm-sup; |
| qcom,vdd-io-voltage-level = <1800000 1800000>; |
| qcom,vdd-io-current-level = <0 325000>; |
| }; |
| |
| &sdhc_2 { |
| status = "ok"; |
| |
| pinctrl-names = "default", "sleep"; |
| pinctrl-0 = <&sdc2_on>; |
| pinctrl-1 = <&sdc2_off>; |
| |
| cap-sd-highspeed; |
| |
| vdd-supply = <&L9E>; |
| qcom,vdd-voltage-level = <2960000 2960000>; |
| qcom,vdd-current-level = <0 800000>; |
| |
| vdd-io-supply = <&L6E>; |
| qcom,vdd-io-voltage-level = <2960000 2960000>; |
| qcom,vdd-io-current-level = <0 22000>; |
| |
| cd-gpios = <&tlmm 94 GPIO_ACTIVE_LOW>; |
| }; |
| |
| &ufsphy_mem { |
| compatible = "qcom,ufs-phy-qrbtc-sdm845"; |
| |
| vdda-phy-supply = <&L18A>; |
| vdda-pll-supply = <&L22A>; |
| vdda-phy-max-microamp = <62900>; |
| vdda-pll-max-microamp = <18300>; |
| |
| status = "ok"; |
| }; |
| |
| &ufshc_mem { |
| |
| limit-tx-hs-gear = <1>; |
| limit-rx-hs-gear = <1>; |
| limit-rate = <1>; /* HS Rate-B */ |
| |
| vdd-hba-supply = <&gcc_ufs_phy_gdsc>; |
| vdd-hba-fixed-regulator; |
| |
| vcc-supply = <&L7E>; |
| vcc-max-microamp = <800000>; |
| |
| vccq2-supply = <&L12A>; |
| vccq2-max-microamp = <800000>; |
| |
| qcom,vddp-ref-clk-supply = <&L22A>; |
| qcom,vddp-ref-clk-max-microamp = <100>; |
| |
| qcom,disable-lpm; |
| rpm-level = <0>; |
| spm-level = <0>; |
| |
| status = "ok"; |
| }; |
| |
| /* Debug UART Console */ |
| &qupv3_se9_2uart { |
| qcom,rumi_platform; |
| }; |
| |
| &qupv3_se10_i2c { |
| status = "disabled"; |
| }; |