| /* |
| * Created 20 Oct 2004 by Mark Lord |
| * |
| * Basic support for Delkin/ASKA/Workbit Cardbus CompactFlash adapter |
| * |
| * Modeled after the 16-bit PCMCIA driver: ide-cs.c |
| * |
| * This is slightly peculiar, in that it is a PCI driver, |
| * but is NOT an IDE PCI driver -- the IDE layer does not directly |
| * support hot insertion/removal of PCI interfaces, so this driver |
| * is unable to use the IDE PCI interfaces. Instead, it uses the |
| * same interfaces as the ide-cs (PCMCIA) driver uses. |
| * On the plus side, the driver is also smaller/simpler this way. |
| * |
| * This file is subject to the terms and conditions of the GNU General Public |
| * License. See the file COPYING in the main directory of this archive for |
| * more details. |
| */ |
| |
| #include <linux/types.h> |
| #include <linux/module.h> |
| #include <linux/ide.h> |
| #include <linux/init.h> |
| #include <linux/pci.h> |
| |
| #include <asm/io.h> |
| |
| /* |
| * No chip documentation has yet been found, |
| * so these configuration values were pulled from |
| * a running Win98 system using "debug". |
| * This gives around 3MByte/second read performance, |
| * which is about 2/3 of what the chip is capable of. |
| * |
| * There is also a 4KByte mmio region on the card, |
| * but its purpose has yet to be reverse-engineered. |
| */ |
| static const u8 setup[] = { |
| 0x00, 0x05, 0xbe, 0x01, 0x20, 0x8f, 0x00, 0x00, |
| 0xa4, 0x1f, 0xb3, 0x1b, 0x00, 0x00, 0x00, 0x80, |
| 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, |
| 0x00, 0x00, 0x00, 0x00, 0xa4, 0x83, 0x02, 0x13, |
| }; |
| |
| static const struct ide_port_ops delkin_cb_port_ops = { |
| .quirkproc = ide_undecoded_slave, |
| }; |
| |
| static int delkin_cb_init_chipset(struct pci_dev *dev) |
| { |
| unsigned long base = pci_resource_start(dev, 0); |
| int i; |
| |
| outb(0x02, base + 0x1e); /* set nIEN to block interrupts */ |
| inb(base + 0x17); /* read status to clear interrupts */ |
| |
| for (i = 0; i < sizeof(setup); ++i) { |
| if (setup[i]) |
| outb(setup[i], base + i); |
| } |
| |
| return 0; |
| } |
| |
| static const struct ide_port_info delkin_cb_port_info = { |
| .port_ops = &delkin_cb_port_ops, |
| .host_flags = IDE_HFLAG_IO_32BIT | IDE_HFLAG_UNMASK_IRQS | |
| IDE_HFLAG_NO_DMA, |
| .init_chipset = delkin_cb_init_chipset, |
| }; |
| |
| static int __devinit |
| delkin_cb_probe (struct pci_dev *dev, const struct pci_device_id *id) |
| { |
| struct ide_host *host; |
| unsigned long base; |
| int rc; |
| hw_regs_t hw, *hws[] = { &hw, NULL, NULL, NULL }; |
| |
| rc = pci_enable_device(dev); |
| if (rc) { |
| printk(KERN_ERR "delkin_cb: pci_enable_device failed (%d)\n", rc); |
| return rc; |
| } |
| rc = pci_request_regions(dev, "delkin_cb"); |
| if (rc) { |
| printk(KERN_ERR "delkin_cb: pci_request_regions failed (%d)\n", rc); |
| pci_disable_device(dev); |
| return rc; |
| } |
| base = pci_resource_start(dev, 0); |
| |
| delkin_cb_init_chipset(dev); |
| |
| memset(&hw, 0, sizeof(hw)); |
| ide_std_init_ports(&hw, base + 0x10, base + 0x1e); |
| hw.irq = dev->irq; |
| hw.dev = &dev->dev; |
| hw.chipset = ide_pci; /* this enables IRQ sharing */ |
| |
| rc = ide_host_add(&delkin_cb_port_info, hws, &host); |
| if (rc) |
| goto out_disable; |
| |
| pci_set_drvdata(dev, host); |
| |
| return 0; |
| |
| out_disable: |
| pci_release_regions(dev); |
| pci_disable_device(dev); |
| return rc; |
| } |
| |
| static void |
| delkin_cb_remove (struct pci_dev *dev) |
| { |
| struct ide_host *host = pci_get_drvdata(dev); |
| |
| ide_host_remove(host); |
| |
| pci_release_regions(dev); |
| pci_disable_device(dev); |
| } |
| |
| #ifdef CONFIG_PM |
| static int delkin_cb_suspend(struct pci_dev *dev, pm_message_t state) |
| { |
| pci_save_state(dev); |
| pci_disable_device(dev); |
| pci_set_power_state(dev, pci_choose_state(dev, state)); |
| |
| return 0; |
| } |
| |
| static int delkin_cb_resume(struct pci_dev *dev) |
| { |
| struct ide_host *host = pci_get_drvdata(dev); |
| int rc; |
| |
| pci_set_power_state(dev, PCI_D0); |
| |
| rc = pci_enable_device(dev); |
| if (rc) |
| return rc; |
| |
| pci_restore_state(dev); |
| pci_set_master(dev); |
| |
| if (host->init_chipset) |
| host->init_chipset(dev); |
| |
| return 0; |
| } |
| #else |
| #define delkin_cb_suspend NULL |
| #define delkin_cb_resume NULL |
| #endif |
| |
| static struct pci_device_id delkin_cb_pci_tbl[] __devinitdata = { |
| { 0x1145, 0xf021, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0}, |
| { 0x1145, 0xf024, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0}, |
| { 0, }, |
| }; |
| MODULE_DEVICE_TABLE(pci, delkin_cb_pci_tbl); |
| |
| static struct pci_driver delkin_cb_pci_driver = { |
| .name = "Delkin-ASKA-Workbit Cardbus IDE", |
| .id_table = delkin_cb_pci_tbl, |
| .probe = delkin_cb_probe, |
| .remove = delkin_cb_remove, |
| .suspend = delkin_cb_suspend, |
| .resume = delkin_cb_resume, |
| }; |
| |
| static int __init delkin_cb_init(void) |
| { |
| return pci_register_driver(&delkin_cb_pci_driver); |
| } |
| |
| static void __exit delkin_cb_exit(void) |
| { |
| pci_unregister_driver(&delkin_cb_pci_driver); |
| } |
| |
| module_init(delkin_cb_init); |
| module_exit(delkin_cb_exit); |
| |
| MODULE_AUTHOR("Mark Lord"); |
| MODULE_DESCRIPTION("Basic support for Delkin/ASKA/Workbit Cardbus IDE"); |
| MODULE_LICENSE("GPL"); |
| |