| |
| menu "Passive cards" |
| depends on ISDN_I4L |
| |
| config ISDN_DRV_HISAX |
| tristate "HiSax SiemensChipSet driver support" |
| select CRC_CCITT |
| ---help--- |
| This is a driver supporting the Siemens chipset on various |
| ISDN-cards (like AVM A1, Elsa ISDN cards, Teles S0-16.0, Teles |
| S0-16.3, Teles S0-8, Teles/Creatix PnP, ITK micro ix1 and many |
| compatibles). |
| |
| HiSax is just the name of this driver, not the name of any hardware. |
| |
| If you have a card with such a chipset, you should say Y here and |
| also to the configuration option of the driver for your particular |
| card, below. |
| |
| if ISDN_DRV_HISAX!=n |
| |
| comment "D-channel protocol features" |
| |
| config HISAX_EURO |
| bool "HiSax Support for EURO/DSS1" |
| help |
| Say Y or N according to the D-channel protocol which your local |
| telephone service company provides. |
| |
| The call control protocol E-DSS1 is used in most European countries. |
| If unsure, say Y. |
| |
| config DE_AOC |
| bool "Support for german chargeinfo" |
| depends on HISAX_EURO |
| help |
| If you want that the HiSax hardware driver sends messages to the |
| upper level of the isdn code on each AOCD (Advice Of Charge, During |
| the call -- transmission of the fee information during a call) and |
| on each AOCE (Advice Of Charge, at the End of the call -- |
| transmission of fee information at the end of the call), say Y here. |
| This works only in Germany. |
| |
| config HISAX_NO_SENDCOMPLETE |
| bool "Disable sending complete" |
| depends on HISAX_EURO |
| help |
| If you have trouble with some ugly exchanges or you live in |
| Australia select this option. |
| |
| config HISAX_NO_LLC |
| bool "Disable sending low layer compatibility" |
| depends on HISAX_EURO |
| help |
| If you have trouble with some ugly exchanges try to select this |
| option. |
| |
| config HISAX_NO_KEYPAD |
| bool "Disable keypad protocol option" |
| depends on HISAX_EURO |
| help |
| If you like to send special dial strings including * or # without |
| using the keypad protocol, select this option. |
| |
| config HISAX_1TR6 |
| bool "HiSax Support for german 1TR6" |
| help |
| Say Y or N according to the D-channel protocol which your local |
| telephone service company provides. |
| |
| 1TR6 is an old call control protocol which was used in Germany |
| before E-DSS1 was established. Nowadays, all new lines in Germany |
| use E-DSS1. |
| |
| config HISAX_NI1 |
| bool "HiSax Support for US NI1" |
| help |
| Enable this if you like to use ISDN in US on a NI1 basic rate |
| interface. |
| |
| config HISAX_MAX_CARDS |
| int "Maximum number of cards supported by HiSax" |
| default "8" |
| help |
| This option allows you to specify the maximum number of cards which |
| the HiSax driver will be able to handle. |
| |
| comment "HiSax supported cards" |
| |
| config HISAX_16_0 |
| bool "Teles 16.0/8.0" |
| depends on ISA |
| help |
| This enables HiSax support for the Teles ISDN-cards S0-16.0, S0-8 |
| and many compatibles. |
| |
| See <file:Documentation/isdn/README.HiSax> on how to configure it |
| using the different cards, a different D-channel protocol, or |
| non-standard IRQ/port/shmem settings. |
| |
| config HISAX_16_3 |
| bool "Teles 16.3 or PNP or PCMCIA" |
| help |
| This enables HiSax support for the Teles ISDN-cards S0-16.3 the |
| Teles/Creatix PnP and the Teles PCMCIA. |
| |
| See <file:Documentation/isdn/README.HiSax> on how to configure it |
| using the different cards, a different D-channel protocol, or |
| non-standard IRQ/port settings. |
| |
| config HISAX_TELESPCI |
| bool "Teles PCI" |
| depends on PCI && (BROKEN || !(SPARC || PPC || PARISC || M68K || (MIPS && !CPU_LITTLE_ENDIAN) || FRV)) |
| help |
| This enables HiSax support for the Teles PCI. |
| See <file:Documentation/isdn/README.HiSax> on how to configure it. |
| |
| config HISAX_S0BOX |
| bool "Teles S0Box" |
| help |
| This enables HiSax support for the Teles/Creatix parallel port |
| S0BOX. See <file:Documentation/isdn/README.HiSax> on how to |
| configure it. |
| |
| config HISAX_AVM_A1 |
| bool "AVM A1 (Fritz)" |
| depends on ISA |
| help |
| This enables HiSax support for the AVM A1 (aka "Fritz"). |
| |
| See <file:Documentation/isdn/README.HiSax> on how to configure it |
| using the different cards, a different D-channel protocol, or |
| non-standard IRQ/port settings. |
| |
| config HISAX_FRITZPCI |
| bool "AVM PnP/PCI (Fritz!PnP/PCI)" |
| depends on BROKEN || !PPC64 |
| help |
| This enables HiSax support for the AVM "Fritz!PnP" and "Fritz!PCI". |
| See <file:Documentation/isdn/README.HiSax> on how to configure it. |
| |
| config HISAX_AVM_A1_PCMCIA |
| bool "AVM A1 PCMCIA (Fritz)" |
| help |
| This enables HiSax support for the AVM A1 "Fritz!PCMCIA"). |
| See <file:Documentation/isdn/README.HiSax> on how to configure it. |
| |
| config HISAX_ELSA |
| bool "Elsa cards" |
| help |
| This enables HiSax support for the Elsa Mircolink ISA cards, for the |
| Elsa Quickstep series cards and Elsa PCMCIA. |
| |
| See <file:Documentation/isdn/README.HiSax> on how to configure it |
| using the different cards, a different D-channel protocol, or |
| non-standard IRQ/port settings. |
| |
| config HISAX_IX1MICROR2 |
| bool "ITK ix1-micro Revision 2" |
| depends on ISA |
| help |
| This enables HiSax support for the ITK ix1-micro Revision 2 card. |
| |
| See <file:Documentation/isdn/README.HiSax> on how to configure it |
| using the different cards, a different D-channel protocol, or |
| non-standard IRQ/port settings. |
| |
| config HISAX_DIEHLDIVA |
| bool "Eicon.Diehl Diva cards" |
| help |
| This enables HiSax support for the Eicon.Diehl Diva none PRO |
| versions passive ISDN cards. |
| |
| See <file:Documentation/isdn/README.HiSax> on how to configure it |
| using the different cards, a different D-channel protocol, or |
| non-standard IRQ/port settings. |
| |
| config HISAX_ASUSCOM |
| bool "ASUSCOM ISA cards" |
| depends on ISA |
| help |
| This enables HiSax support for the AsusCom and their OEM versions |
| passive ISDN ISA cards. |
| |
| See <file:Documentation/isdn/README.HiSax> on how to configure it |
| using the different cards, a different D-channel protocol, or |
| non-standard IRQ/port settings. |
| |
| config HISAX_TELEINT |
| bool "TELEINT cards" |
| depends on ISA |
| help |
| This enables HiSax support for the TELEINT SA1 semiactiv ISDN card. |
| |
| See <file:Documentation/isdn/README.HiSax> on how to configure it |
| using the different cards, a different D-channel protocol, or |
| non-standard IRQ/port settings. |
| |
| config HISAX_HFCS |
| bool "HFC-S based cards" |
| depends on ISA |
| help |
| This enables HiSax support for the HFC-S 2BDS0 based cards, like |
| teles 16.3c. |
| |
| See <file:Documentation/isdn/README.HiSax> on how to configure it |
| using the different cards, a different D-channel protocol, or |
| non-standard IRQ/port settings. |
| |
| config HISAX_SEDLBAUER |
| bool "Sedlbauer cards" |
| help |
| This enables HiSax support for the Sedlbauer passive ISDN cards. |
| |
| See <file:Documentation/isdn/README.HiSax> on how to configure it |
| using the different cards, a different D-channel protocol, or |
| non-standard IRQ/port settings. |
| |
| config HISAX_SPORTSTER |
| bool "USR Sportster internal TA" |
| depends on ISA |
| help |
| This enables HiSax support for the USR Sportster internal TA card. |
| |
| See <file:Documentation/isdn/README.HiSax> on how to configure it |
| using a different D-channel protocol, or non-standard IRQ/port |
| settings. |
| |
| config HISAX_MIC |
| bool "MIC card" |
| depends on ISA |
| help |
| This enables HiSax support for the ITH MIC card. |
| |
| See <file:Documentation/isdn/README.HiSax> on how to configure it |
| using a different D-channel protocol, or non-standard IRQ/port |
| settings. |
| |
| config HISAX_NETJET |
| bool "NETjet card" |
| depends on PCI && (BROKEN || !(SPARC || PPC || PARISC || M68K || (MIPS && !CPU_LITTLE_ENDIAN) || FRV)) |
| help |
| This enables HiSax support for the NetJet from Traverse |
| Technologies. |
| |
| See <file:Documentation/isdn/README.HiSax> on how to configure it |
| using a different D-channel protocol, or non-standard IRQ/port |
| settings. |
| |
| config HISAX_NETJET_U |
| bool "NETspider U card" |
| depends on PCI && (BROKEN || !(SPARC || PPC || PARISC || M68K || (MIPS && !CPU_LITTLE_ENDIAN) || FRV)) |
| help |
| This enables HiSax support for the Netspider U interface ISDN card |
| from Traverse Technologies. |
| See <file:Documentation/isdn/README.HiSax> on how to configure it |
| using a different D-channel protocol, or non-standard IRQ/port |
| settings. |
| |
| config HISAX_NICCY |
| bool "Niccy PnP/PCI card" |
| help |
| This enables HiSax support for the Dr. Neuhaus Niccy PnP or PCI. |
| |
| See <file:Documentation/isdn/README.HiSax> on how to configure it |
| using a different D-channel protocol, or non-standard IRQ/port |
| settings. |
| |
| config HISAX_ISURF |
| bool "Siemens I-Surf card" |
| depends on ISA |
| help |
| This enables HiSax support for the Siemens I-Talk/I-Surf card with |
| ISAR chip. |
| See <file:Documentation/isdn/README.HiSax> on how to configure it |
| using a different D-channel protocol, or non-standard IRQ/port |
| settings. |
| |
| config HISAX_HSTSAPHIR |
| bool "HST Saphir card" |
| depends on ISA |
| help |
| This enables HiSax support for the HST Saphir card. |
| |
| See <file:Documentation/isdn/README.HiSax> on how to configure it |
| using a different D-channel protocol, or non-standard IRQ/port |
| settings. |
| |
| config HISAX_BKM_A4T |
| bool "Telekom A4T card" |
| depends on PCI |
| help |
| This enables HiSax support for the Telekom A4T card. |
| |
| See <file:Documentation/isdn/README.HiSax> on how to configure it |
| using a different D-channel protocol, or non-standard IRQ/port |
| settings. |
| |
| config HISAX_SCT_QUADRO |
| bool "Scitel Quadro card" |
| depends on PCI |
| help |
| This enables HiSax support for the Scitel Quadro card. |
| |
| See <file:Documentation/isdn/README.HiSax> on how to configure it |
| using a different D-channel protocol, or non-standard IRQ/port |
| settings. |
| |
| config HISAX_GAZEL |
| bool "Gazel cards" |
| help |
| This enables HiSax support for the Gazel cards. |
| |
| See <file:Documentation/isdn/README.HiSax> on how to configure it |
| using a different D-channel protocol, or non-standard IRQ/port |
| settings. |
| |
| config HISAX_HFC_PCI |
| bool "HFC PCI-Bus cards" |
| depends on PCI && (BROKEN || !(SPARC || PPC || PARISC || M68K || (MIPS && !CPU_LITTLE_ENDIAN) || FRV)) |
| help |
| This enables HiSax support for the HFC-S PCI 2BDS0 based cards. |
| |
| For more information see under |
| <file:Documentation/isdn/README.hfc-pci>. |
| |
| config HISAX_W6692 |
| bool "Winbond W6692 based cards" |
| depends on PCI |
| help |
| This enables HiSax support for Winbond W6692 based PCI ISDN cards. |
| |
| See <file:Documentation/isdn/README.HiSax> on how to configure it |
| using a different D-channel protocol, or non-standard IRQ/port |
| settings. |
| |
| config HISAX_HFC_SX |
| bool "HFC-S+, HFC-SP, HFC-PCMCIA cards" |
| help |
| This enables HiSax support for the HFC-S+, HFC-SP and HFC-PCMCIA |
| cards. This code is not finished yet. |
| |
| config HISAX_ENTERNOW_PCI |
| bool "Formula-n enter:now PCI card" |
| depends on HISAX_NETJET && PCI && (BROKEN || !(SPARC || PPC || PARISC || M68K || (MIPS && !CPU_LITTLE_ENDIAN) || FRV)) |
| help |
| This enables HiSax support for the Formula-n enter:now PCI |
| ISDN card. |
| |
| endif |
| |
| if ISDN_DRV_HISAX |
| |
| config HISAX_DEBUG |
| bool "HiSax debugging" |
| help |
| This enables debugging code in the new-style HiSax drivers, i.e. |
| the ST5481 USB driver currently. |
| If in doubt, say yes. |
| |
| comment "HiSax PCMCIA card service modules" |
| |
| config HISAX_SEDLBAUER_CS |
| tristate "Sedlbauer PCMCIA cards" |
| depends on PCMCIA && HISAX_SEDLBAUER |
| help |
| This enables the PCMCIA client driver for the Sedlbauer Speed Star |
| and Speed Star II cards. |
| |
| config HISAX_ELSA_CS |
| tristate "ELSA PCMCIA MicroLink cards" |
| depends on PCMCIA && HISAX_ELSA |
| help |
| This enables the PCMCIA client driver for the Elsa PCMCIA MicroLink |
| card. |
| |
| config HISAX_AVM_A1_CS |
| tristate "AVM A1 PCMCIA cards" |
| depends on PCMCIA && ISDN_DRV_HISAX |
| help |
| This enables the PCMCIA client driver for the AVM A1 / Fritz!Card |
| PCMCIA cards. |
| |
| config HISAX_TELES_CS |
| tristate "TELES PCMCIA cards" |
| depends on PCMCIA && HISAX_16_3 |
| help |
| This enables the PCMCIA client driver for the Teles PCMCIA cards. |
| |
| comment "HiSax sub driver modules" |
| |
| config HISAX_ST5481 |
| tristate "ST5481 USB ISDN modem (EXPERIMENTAL)" |
| depends on USB && EXPERIMENTAL |
| select CRC_CCITT |
| select BITREVERSE |
| help |
| This enables the driver for ST5481 based USB ISDN adapters, |
| e.g. the BeWan Gazel 128 USB |
| |
| config HISAX_HFCUSB |
| tristate "HFC USB based ISDN modems (EXPERIMENTAL)" |
| depends on USB && EXPERIMENTAL |
| help |
| This enables the driver for HFC USB based ISDN modems. |
| |
| config HISAX_HFC4S8S |
| tristate "HFC-4S/8S based ISDN cards (EXPERIMENTAL)" |
| depends on EXPERIMENTAL |
| help |
| This enables the driver for HFC-4S/8S based ISDN cards. |
| |
| config HISAX_FRITZ_PCIPNP |
| tristate "AVM Fritz!Card PCI/PCIv2/PnP support (EXPERIMENTAL)" |
| depends on PCI && EXPERIMENTAL |
| help |
| This enables the driver for the AVM Fritz!Card PCI, |
| Fritz!Card PCI v2 and Fritz!Card PnP. |
| (the latter also needs you to select "ISA Plug and Play support" |
| from the menu "Plug and Play configuration") |
| |
| config HISAX_HDLC |
| bool |
| depends on HISAX_ST5481 |
| default y |
| |
| config HISAX_AVM_A1_PCMCIA |
| bool |
| depends on HISAX_AVM_A1_CS |
| default y |
| |
| endif |
| |
| endmenu |
| |