Documentation/isdn/README.gigaset - kernel/msm - Gitiles

 GigaSet 307x Device Driver
 ==========================

 1.   Requirements
      ------------
 1.1. Hardware
      --------
      This release supports the connection of the Gigaset 307x/417x family of
      ISDN DECT bases via Gigaset M101 Data, Gigaset M105 Data or direct USB
      connection. The following devices are reported to be compatible:
      307x/417x:
         Gigaset SX255isdn
         Gigaset SX353isdn
         Sinus 45 [AB] isdn (Deutsche Telekom)
         Sinus 721X/XA
         Vox Chicago 390 ISDN (KPN Telecom)
      M101:
         Sinus 45 Data 1 (Telekom)
      M105:
         Gigaset USB Adapter DECT
         Sinus 45 Data 2 (Telekom)
         Sinus 721 data
         Chicago 390 USB (KPN)
      See also http://www.erbze.info/sinus_gigaset.htm and
               http://gigaset307x.sourceforge.net/

      We had also reports from users of Gigaset M105 who could use the drivers
      with SX 100 and CX 100 ISDN bases (only in unimodem mode, see section 2.4.)
      If you have another device that works with our driver, please let us know.
      For example, Gigaset SX205isdn/Sinus 721 X SE and Gigaset SX303isdn bases
      are just versions without answering machine of models known to work, so
      they should work just as well; but so far we are lacking positive reports
      on these.

      Chances of getting an USB device to work are good if the output of
         lsusb
      at the command line contains one of the following:
         ID 0681:0001
         ID 0681:0002
         ID 0681:0009
         ID 0681:0021
         ID 0681:0022

 1.2. Software
      --------
      The driver works with ISDN4linux and so can be used with any software
      which is able to use ISDN4linux for ISDN connections (voice or data).
      CAPI4Linux support is planned but not yet available.

      There are some user space tools available at
      http://sourceforge.net/projects/gigaset307x/
      which provide access to additional device specific functions like SMS,
      phonebook or call journal.


 2.   How to use the driver
      ---------------------
 2.1. Modules
      -------
      To get the device working, you have to load the proper kernel module. You
      can do this using
          modprobe modulename
      where modulename is usb_gigaset (M105) or bas_gigaset (direct USB
      connection to the base).

 2.2. Device nodes for user space programs
      ------------------------------------
      The device can be accessed from user space (eg. by the user space tools
      mentioned in 1.2.) through the device nodes:

      - /dev/ttyGU0 for M105 (USB data boxes)
      - /dev/ttyGB0 for the base driver (direct USB connection)

      You can also select a "default device" which is used by the frontends when
      no device node is given as parameter, by creating a symlink /dev/ttyG to
      one of them, eg.:

         ln -s /dev/ttyGB0 /dev/ttyG

 2.3. ISDN4linux
      ----------
      This is the "normal" mode of operation. After loading the module you can
      set up the ISDN system just as you'd do with any ISDN card.
      Your distribution should provide some configuration utility.
      If not, you can use some HOWTOs like
          http://www.linuxhaven.de/dlhp/HOWTO/DE-ISDN-HOWTO-5.html
      If this doesn't work, because you have some recent device like SX100 where
      debug output (see section 3.2.) shows something like this when dialing
          CMD Received: ERROR
          Available Params: 0
          Connection State: 0, Response: -1
          gigaset_process_response: resp_code -1 in ConState 0 !
          Timeout occurred
      you might need to use unimodem mode:

 2.4. Unimodem mode
      -------------
      This is needed for some devices [e.g. SX100] as they have problems with
      the "normal" commands.

      If you have installed the command line tool gigacontr, you can enter
      unimodem mode using
          gigacontr --mode unimodem
      You can switch back using
          gigacontr --mode isdn

      You can also load the driver using e.g.
          modprobe usb_gigaset startmode=0
      to prevent the driver from starting in "isdn4linux mode".

      In this mode the device works like a modem connected to a serial port
      (the /dev/ttyGU0, ... mentioned above) which understands the commands
          ATZ                 init, reset
              => OK or ERROR
          ATD
          ATDT                dial
              => OK, CONNECT,
                 BUSY,
                 NO DIAL TONE,
                 NO CARRIER,
                 NO ANSWER
          <pause>+++<pause>   change to command mode when connected
          ATH                 hangup

      You can use some configuration tool of your distribution to configure this
      "modem" or configure pppd/wvdial manually. There are some example ppp
      configuration files and chat scripts in the gigaset-VERSION/ppp directory
      in the driver packages from http://sourceforge.net/projects/gigaset307x/.
      Please note that the USB drivers are not able to change the state of the
      control lines (the M105 driver can be configured to use some undocumented
      control requests, if you really need the control lines, though). This means
      you must use "Stupid Mode" if you are using wvdial or you should use the
      nocrtscts option of pppd.
      You must also assure that the ppp_async module is loaded with the parameter
      flag_time=0. You can do this e.g. by adding a line like

         options ppp_async flag_time=0

      to /etc/modprobe.conf. If your distribution has some local module
      configuration file like /etc/modprobe.conf.local,
      using that should be preferred.

 2.5. Call-ID (CID) mode
      ------------------
      Call-IDs are numbers used to tag commands to, and responses from, the
      Gigaset base in order to support the simultaneous handling of multiple
      ISDN calls. Their use can be enabled ("CID mode") or disabled ("Unimodem
      mode"). Without Call-IDs (in Unimodem mode), only a very limited set of
      functions is available. It allows outgoing data connections only, but
      does not signal incoming calls or other base events.

      DECT cordless data devices (M10x) permanently occupy the cordless
      connection to the base while Call-IDs are activated. As the Gigaset
      bases only support one DECT data connection at a time, this prevents
      other DECT cordless data devices from accessing the base.

      During active operation, the driver switches to the necessary mode
      automatically. However, for the reasons above, the mode chosen when
      the device is not in use (idle) can be selected by the user.
      - If you want to receive incoming calls, you can use the default
        settings (CID mode).
      - If you have several DECT data devices (M10x) which you want to use
        in turn, select Unimodem mode by passing the parameter "cidmode=0" to
        the driver ("modprobe usb_gigaset cidmode=0" or modprobe.conf).

      If you want both of these at once, you are out of luck.

      You can also use /sys/class/tty/ttyGxy/cidmode for changing the CID mode
      setting (ttyGxy is ttyGU0 or ttyGB0).


 3.   Troubleshooting
      ---------------
 3.1. Solutions to frequently reported problems
      -----------------------------------------
      Problem:
         You have a slow provider and isdn4linux gives up dialing too early.
      Solution:
         Load the isdn module using the dialtimeout option. You can do this e.g.
         by adding a line like

            options isdn dialtimeout=15

         to /etc/modprobe.conf. If your distribution has some local module
         configuration file like /etc/modprobe.conf.local,
         using that should be preferred.

      Problem:
         Your isdn script aborts with a message about isdnlog.
      Solution:
         Try deactivating (or commenting out) isdnlog. This driver does not
         support it.

      Problem:
         You have two or more DECT data adapters (M101/M105) and only the
         first one you turn on works.
      Solution:
         Select Unimodem mode for all DECT data adapters. (see section 2.4.)

 3.2. Telling the driver to provide more information
      ----------------------------------------------
      Building the driver with the "Gigaset debugging" kernel configuration
      option (CONFIG_GIGASET_DEBUG) gives it the ability to produce additional
      information useful for debugging.

      You can control the amount of debugging information the driver produces by
      writing an appropriate value to /sys/module/gigaset/parameters/debug, e.g.
         echo 0 > /sys/module/gigaset/parameters/debug
      switches off debugging output completely,
         echo 0x10a020 > /sys/module/gigaset/parameters/debug
      enables the standard set of debugging output messages. These values are
      bit patterns where every bit controls a certain type of debugging output.
      See the constants DEBUG_* in the source file gigaset.h for details.

      The initial value can be set using the debug parameter when loading the
      module "gigaset", e.g. by adding a line
         options gigaset debug=0
      to /etc/modprobe.conf, ...

      Generated debugging information can be found
      - as output of the command
          dmesg
      - in system log files written by your syslog daemon, usually
        in /var/log/, e.g. /var/log/messages.

 3.3. Reporting problems and bugs
      ---------------------------
      If you can't solve problems with the driver on your own, feel free to
      use one of the forums, bug trackers, or mailing lists on
          http://sourceforge.net/projects/gigaset307x
      or write an electronic mail to the maintainers.

      Try to provide as much information as possible, such as
      - distribution
      - kernel version (uname -r)
      - gcc version (gcc --version)
      - hardware architecture (uname -m, ...)
      - type and firmware version of your device (base and wireless module,
        if any)
      - output of "lsusb -v" (if using an USB device)
      - error messages
      - relevant system log messages (it would help if you activate debug
        output as described in 3.2.)

      For help with general configuration problems not specific to our driver,
      such as isdn4linux and network configuration issues, please refer to the
      appropriate forums and newsgroups.

 3.4. Reporting problem solutions
      ---------------------------
      If you solved a problem with our drivers, wrote startup scripts for your
      distribution, ... feel free to contact us (using one of the places
      mentioned in 3.3.). We'd like to add scripts, hints, documentation
      to the driver and/or the project web page.


 4.   Links, other software
      ---------------------
      - Sourceforge project developing this driver and associated tools
          http://sourceforge.net/projects/gigaset307x
      - Yahoo! Group on the Siemens Gigaset family of devices
          http://de.groups.yahoo.com/group/Siemens-Gigaset
      - Siemens Gigaset/T-Sinus compatibility table
          http://www.erbze.info/sinus_gigaset.htm


 5.   Credits
      -------
      Thanks to

      Karsten Keil
         for his help with isdn4linux
      Deti Fliegl
         for his base driver code
      Dennis Dietrich
         for his kernel 2.6 patches
      Andreas Rummel
         for his work and logs to get unimodem mode working
      Andreas Degert
         for his logs and patches to get cx 100 working
      Dietrich Feist
         for his generous donation of one M105 and two M101 cordless adapters
      Christoph Schweers
         for his generous donation of a M34 device

      and all the other people who sent logs and other information.
	GigaSet 307x Device Driver
	==========================

	1. Requirements
	------------
	1.1. Hardware
	--------
	This release supports the connection of the Gigaset 307x/417x family of
	ISDN DECT bases via Gigaset M101 Data, Gigaset M105 Data or direct USB
	connection. The following devices are reported to be compatible:
	307x/417x:
	Gigaset SX255isdn
	Gigaset SX353isdn
	Sinus 45 [AB] isdn (Deutsche Telekom)
	Sinus 721X/XA
	Vox Chicago 390 ISDN (KPN Telecom)
	M101:
	Sinus 45 Data 1 (Telekom)
	M105:
	Gigaset USB Adapter DECT
	Sinus 45 Data 2 (Telekom)
	Sinus 721 data
	Chicago 390 USB (KPN)
	See also http://www.erbze.info/sinus_gigaset.htm and
	http://gigaset307x.sourceforge.net/

	We had also reports from users of Gigaset M105 who could use the drivers
	with SX 100 and CX 100 ISDN bases (only in unimodem mode, see section 2.4.)
	If you have another device that works with our driver, please let us know.
	For example, Gigaset SX205isdn/Sinus 721 X SE and Gigaset SX303isdn bases
	are just versions without answering machine of models known to work, so
	they should work just as well; but so far we are lacking positive reports
	on these.

	Chances of getting an USB device to work are good if the output of
	lsusb
	at the command line contains one of the following:
	ID 0681:0001
	ID 0681:0002
	ID 0681:0009
	ID 0681:0021
	ID 0681:0022

	1.2. Software
	--------
	The driver works with ISDN4linux and so can be used with any software
	which is able to use ISDN4linux for ISDN connections (voice or data).
	CAPI4Linux support is planned but not yet available.

	There are some user space tools available at
	http://sourceforge.net/projects/gigaset307x/
	which provide access to additional device specific functions like SMS,
	phonebook or call journal.


	2. How to use the driver
	---------------------
	2.1. Modules
	-------
	To get the device working, you have to load the proper kernel module. You
	can do this using
	modprobe modulename
	where modulename is usb_gigaset (M105) or bas_gigaset (direct USB
	connection to the base).

	2.2. Device nodes for user space programs
	------------------------------------
	The device can be accessed from user space (eg. by the user space tools
	mentioned in 1.2.) through the device nodes:

	- /dev/ttyGU0 for M105 (USB data boxes)
	- /dev/ttyGB0 for the base driver (direct USB connection)

	You can also select a "default device" which is used by the frontends when
	no device node is given as parameter, by creating a symlink /dev/ttyG to
	one of them, eg.:

	ln -s /dev/ttyGB0 /dev/ttyG

	2.3. ISDN4linux
	----------
	This is the "normal" mode of operation. After loading the module you can
	set up the ISDN system just as you'd do with any ISDN card.
	Your distribution should provide some configuration utility.
	If not, you can use some HOWTOs like
	http://www.linuxhaven.de/dlhp/HOWTO/DE-ISDN-HOWTO-5.html
	If this doesn't work, because you have some recent device like SX100 where
	debug output (see section 3.2.) shows something like this when dialing
	CMD Received: ERROR
	Available Params: 0
	Connection State: 0, Response: -1
	gigaset_process_response: resp_code -1 in ConState 0 !
	Timeout occurred
	you might need to use unimodem mode:

	2.4. Unimodem mode
	-------------
	This is needed for some devices [e.g. SX100] as they have problems with
	the "normal" commands.

	If you have installed the command line tool gigacontr, you can enter
	unimodem mode using
	gigacontr --mode unimodem
	You can switch back using
	gigacontr --mode isdn

	You can also load the driver using e.g.
	modprobe usb_gigaset startmode=0
	to prevent the driver from starting in "isdn4linux mode".

	In this mode the device works like a modem connected to a serial port
	(the /dev/ttyGU0, ... mentioned above) which understands the commands
	ATZ init, reset
	=> OK or ERROR
	ATD
	ATDT dial
	=> OK, CONNECT,
	BUSY,
	NO DIAL TONE,
	NO CARRIER,
	NO ANSWER
	<pause>+++<pause> change to command mode when connected
	ATH hangup

	You can use some configuration tool of your distribution to configure this
	"modem" or configure pppd/wvdial manually. There are some example ppp
	configuration files and chat scripts in the gigaset-VERSION/ppp directory
	in the driver packages from http://sourceforge.net/projects/gigaset307x/.
	Please note that the USB drivers are not able to change the state of the
	control lines (the M105 driver can be configured to use some undocumented
	control requests, if you really need the control lines, though). This means
	you must use "Stupid Mode" if you are using wvdial or you should use the
	nocrtscts option of pppd.
	You must also assure that the ppp_async module is loaded with the parameter
	flag_time=0. You can do this e.g. by adding a line like

	options ppp_async flag_time=0

	to /etc/modprobe.conf. If your distribution has some local module
	configuration file like /etc/modprobe.conf.local,
	using that should be preferred.

	2.5. Call-ID (CID) mode
	------------------
	Call-IDs are numbers used to tag commands to, and responses from, the
	Gigaset base in order to support the simultaneous handling of multiple
	ISDN calls. Their use can be enabled ("CID mode") or disabled ("Unimodem
	mode"). Without Call-IDs (in Unimodem mode), only a very limited set of
	functions is available. It allows outgoing data connections only, but
	does not signal incoming calls or other base events.

	DECT cordless data devices (M10x) permanently occupy the cordless
	connection to the base while Call-IDs are activated. As the Gigaset
	bases only support one DECT data connection at a time, this prevents
	other DECT cordless data devices from accessing the base.

	During active operation, the driver switches to the necessary mode
	automatically. However, for the reasons above, the mode chosen when
	the device is not in use (idle) can be selected by the user.
	- If you want to receive incoming calls, you can use the default
	settings (CID mode).
	- If you have several DECT data devices (M10x) which you want to use
	in turn, select Unimodem mode by passing the parameter "cidmode=0" to
	the driver ("modprobe usb_gigaset cidmode=0" or modprobe.conf).

	If you want both of these at once, you are out of luck.

	You can also use /sys/class/tty/ttyGxy/cidmode for changing the CID mode
	setting (ttyGxy is ttyGU0 or ttyGB0).


	3. Troubleshooting
	---------------
	3.1. Solutions to frequently reported problems
	-----------------------------------------
	Problem:
	You have a slow provider and isdn4linux gives up dialing too early.
	Solution:
	Load the isdn module using the dialtimeout option. You can do this e.g.
	by adding a line like

	options isdn dialtimeout=15

	to /etc/modprobe.conf. If your distribution has some local module
	configuration file like /etc/modprobe.conf.local,
	using that should be preferred.

	Problem:
	Your isdn script aborts with a message about isdnlog.
	Solution:
	Try deactivating (or commenting out) isdnlog. This driver does not
	support it.

	Problem:
	You have two or more DECT data adapters (M101/M105) and only the
	first one you turn on works.
	Solution:
	Select Unimodem mode for all DECT data adapters. (see section 2.4.)

	3.2. Telling the driver to provide more information
	----------------------------------------------
	Building the driver with the "Gigaset debugging" kernel configuration
	option (CONFIG_GIGASET_DEBUG) gives it the ability to produce additional
	information useful for debugging.

	You can control the amount of debugging information the driver produces by
	writing an appropriate value to /sys/module/gigaset/parameters/debug, e.g.
	echo 0 > /sys/module/gigaset/parameters/debug
	switches off debugging output completely,
	echo 0x10a020 > /sys/module/gigaset/parameters/debug
	enables the standard set of debugging output messages. These values are
	bit patterns where every bit controls a certain type of debugging output.
	See the constants DEBUG_* in the source file gigaset.h for details.

	The initial value can be set using the debug parameter when loading the
	module "gigaset", e.g. by adding a line
	options gigaset debug=0
	to /etc/modprobe.conf, ...

	Generated debugging information can be found
	- as output of the command
	dmesg
	- in system log files written by your syslog daemon, usually
	in /var/log/, e.g. /var/log/messages.

	3.3. Reporting problems and bugs
	---------------------------
	If you can't solve problems with the driver on your own, feel free to
	use one of the forums, bug trackers, or mailing lists on
	http://sourceforge.net/projects/gigaset307x
	or write an electronic mail to the maintainers.

	Try to provide as much information as possible, such as
	- distribution
	- kernel version (uname -r)
	- gcc version (gcc --version)
	- hardware architecture (uname -m, ...)
	- type and firmware version of your device (base and wireless module,
	if any)
	- output of "lsusb -v" (if using an USB device)
	- error messages
	- relevant system log messages (it would help if you activate debug
	output as described in 3.2.)

	For help with general configuration problems not specific to our driver,
	such as isdn4linux and network configuration issues, please refer to the
	appropriate forums and newsgroups.

	3.4. Reporting problem solutions
	---------------------------
	If you solved a problem with our drivers, wrote startup scripts for your
	distribution, ... feel free to contact us (using one of the places
	mentioned in 3.3.). We'd like to add scripts, hints, documentation
	to the driver and/or the project web page.


	4. Links, other software
	---------------------
	- Sourceforge project developing this driver and associated tools
	http://sourceforge.net/projects/gigaset307x
	- Yahoo! Group on the Siemens Gigaset family of devices
	http://de.groups.yahoo.com/group/Siemens-Gigaset
	- Siemens Gigaset/T-Sinus compatibility table
	http://www.erbze.info/sinus_gigaset.htm


	5. Credits
	-------
	Thanks to

	Karsten Keil
	for his help with isdn4linux
	Deti Fliegl
	for his base driver code
	Dennis Dietrich
	for his kernel 2.6 patches
	Andreas Rummel
	for his work and logs to get unimodem mode working
	Andreas Degert
	for his logs and patches to get cx 100 working
	Dietrich Feist
	for his generous donation of one M105 and two M101 cordless adapters
	Christoph Schweers
	for his generous donation of a M34 device

	and all the other people who sent logs and other information.