| /************************************************************************** |
| * Initio 9100 device driver for Linux. |
| * |
| * Copyright (c) 1994-1998 Initio Corporation |
| * All rights reserved. |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License as published by |
| * the Free Software Foundation; either version 2, or (at your option) |
| * any later version. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| * |
| * You should have received a copy of the GNU General Public License |
| * along with this program; see the file COPYING. If not, write to |
| * the Free Software Foundation, 675 Mass Ave, Cambridge, MA 02139, USA. |
| * |
| * -------------------------------------------------------------------------- |
| * |
| * Redistribution and use in source and binary forms, with or without |
| * modification, are permitted provided that the following conditions |
| * are met: |
| * 1. Redistributions of source code must retain the above copyright |
| * notice, this list of conditions, and the following disclaimer, |
| * without modification, immediately at the beginning of the file. |
| * 2. Redistributions in binary form must reproduce the above copyright |
| * notice, this list of conditions and the following disclaimer in the |
| * documentation and/or other materials provided with the distribution. |
| * 3. The name of the author may not be used to endorse or promote products |
| * derived from this software without specific prior written permission. |
| * |
| * Where this Software is combined with software released under the terms of |
| * the GNU General Public License ("GPL") and the terms of the GPL would require the |
| * combined work to also be released under the terms of the GPL, the terms |
| * and conditions of this License will apply in addition to those of the |
| * GPL with the exception of any terms or conditions of this License that |
| * conflict with, or are expressly prohibited by, the GPL. |
| * |
| * THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND |
| * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE |
| * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE |
| * ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR |
| * ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL |
| * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS |
| * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) |
| * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT |
| * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY |
| * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF |
| * SUCH DAMAGE. |
| * |
| **************************************************************************/ |
| |
| |
| #include <linux/config.h> |
| #include <linux/types.h> |
| |
| #define ULONG unsigned long |
| #define USHORT unsigned short |
| #define UCHAR unsigned char |
| #define BYTE unsigned char |
| #define WORD unsigned short |
| #define DWORD unsigned long |
| #define UBYTE unsigned char |
| #define UWORD unsigned short |
| #define UDWORD unsigned long |
| #define U32 u32 |
| |
| #define TOTAL_SG_ENTRY 32 |
| #define MAX_SUPPORTED_ADAPTERS 8 |
| #define MAX_OFFSET 15 |
| #define MAX_TARGETS 16 |
| |
| typedef struct { |
| unsigned short base; |
| unsigned short vec; |
| } i91u_config; |
| |
| /***************************************/ |
| /* Tulip Configuration Register Set */ |
| /***************************************/ |
| #define TUL_PVID 0x00 /* Vendor ID */ |
| #define TUL_PDID 0x02 /* Device ID */ |
| #define TUL_PCMD 0x04 /* Command */ |
| #define TUL_PSTUS 0x06 /* Status */ |
| #define TUL_PRID 0x08 /* Revision number */ |
| #define TUL_PPI 0x09 /* Programming interface */ |
| #define TUL_PSC 0x0A /* Sub Class */ |
| #define TUL_PBC 0x0B /* Base Class */ |
| #define TUL_PCLS 0x0C /* Cache line size */ |
| #define TUL_PLTR 0x0D /* Latency timer */ |
| #define TUL_PHDT 0x0E /* Header type */ |
| #define TUL_PBIST 0x0F /* BIST */ |
| #define TUL_PBAD 0x10 /* Base address */ |
| #define TUL_PBAD1 0x14 /* Base address */ |
| #define TUL_PBAD2 0x18 /* Base address */ |
| #define TUL_PBAD3 0x1C /* Base address */ |
| #define TUL_PBAD4 0x20 /* Base address */ |
| #define TUL_PBAD5 0x24 /* Base address */ |
| #define TUL_PRSVD 0x28 /* Reserved */ |
| #define TUL_PRSVD1 0x2C /* Reserved */ |
| #define TUL_PRAD 0x30 /* Expansion ROM base address */ |
| #define TUL_PRSVD2 0x34 /* Reserved */ |
| #define TUL_PRSVD3 0x38 /* Reserved */ |
| #define TUL_PINTL 0x3C /* Interrupt line */ |
| #define TUL_PINTP 0x3D /* Interrupt pin */ |
| #define TUL_PIGNT 0x3E /* MIN_GNT */ |
| #define TUL_PMGNT 0x3F /* MAX_GNT */ |
| |
| /************************/ |
| /* Jasmin Register Set */ |
| /************************/ |
| #define TUL_HACFG0 0x40 /* H/A Configuration Register 0 */ |
| #define TUL_HACFG1 0x41 /* H/A Configuration Register 1 */ |
| #define TUL_HACFG2 0x42 /* H/A Configuration Register 2 */ |
| |
| #define TUL_SDCFG0 0x44 /* SCSI Device Configuration 0 */ |
| #define TUL_SDCFG1 0x45 /* SCSI Device Configuration 1 */ |
| #define TUL_SDCFG2 0x46 /* SCSI Device Configuration 2 */ |
| #define TUL_SDCFG3 0x47 /* SCSI Device Configuration 3 */ |
| |
| #define TUL_GINTS 0x50 /* Global Interrupt Status Register */ |
| #define TUL_GIMSK 0x52 /* Global Interrupt MASK Register */ |
| #define TUL_GCTRL 0x54 /* Global Control Register */ |
| #define TUL_GCTRL_EEPROM_BIT 0x04 |
| #define TUL_GCTRL1 0x55 /* Global Control Register */ |
| #define TUL_DMACFG 0x5B /* DMA configuration */ |
| #define TUL_NVRAM 0x5D /* Non-volatile RAM port */ |
| |
| #define TUL_SCnt0 0x80 /* 00 R/W Transfer Counter Low */ |
| #define TUL_SCnt1 0x81 /* 01 R/W Transfer Counter Mid */ |
| #define TUL_SCnt2 0x82 /* 02 R/W Transfer Count High */ |
| #define TUL_SFifoCnt 0x83 /* 03 R FIFO counter */ |
| #define TUL_SIntEnable 0x84 /* 03 W Interrupt enble */ |
| #define TUL_SInt 0x84 /* 04 R Interrupt Register */ |
| #define TUL_SCtrl0 0x85 /* 05 W Control 0 */ |
| #define TUL_SStatus0 0x85 /* 05 R Status 0 */ |
| #define TUL_SCtrl1 0x86 /* 06 W Control 1 */ |
| #define TUL_SStatus1 0x86 /* 06 R Status 1 */ |
| #define TUL_SConfig 0x87 /* 07 W Configuration */ |
| #define TUL_SStatus2 0x87 /* 07 R Status 2 */ |
| #define TUL_SPeriod 0x88 /* 08 W Sync. Transfer Period & Offset */ |
| #define TUL_SOffset 0x88 /* 08 R Offset */ |
| #define TUL_SScsiId 0x89 /* 09 W SCSI ID */ |
| #define TUL_SBusId 0x89 /* 09 R SCSI BUS ID */ |
| #define TUL_STimeOut 0x8A /* 0A W Sel/Resel Time Out Register */ |
| #define TUL_SIdent 0x8A /* 0A R Identify Message Register */ |
| #define TUL_SAvail 0x8A /* 0A R Availiable Counter Register */ |
| #define TUL_SData 0x8B /* 0B R/W SCSI data in/out */ |
| #define TUL_SFifo 0x8C /* 0C R/W FIFO */ |
| #define TUL_SSignal 0x90 /* 10 R/W SCSI signal in/out */ |
| #define TUL_SCmd 0x91 /* 11 R/W Command */ |
| #define TUL_STest0 0x92 /* 12 R/W Test0 */ |
| #define TUL_STest1 0x93 /* 13 R/W Test1 */ |
| #define TUL_SCFG1 0x94 /* 14 R/W Configuration */ |
| |
| #define TUL_XAddH 0xC0 /*DMA Transfer Physical Address */ |
| #define TUL_XAddW 0xC8 /*DMA Current Transfer Physical Address */ |
| #define TUL_XCntH 0xD0 /*DMA Transfer Counter */ |
| #define TUL_XCntW 0xD4 /*DMA Current Transfer Counter */ |
| #define TUL_XCmd 0xD8 /*DMA Command Register */ |
| #define TUL_Int 0xDC /*Interrupt Register */ |
| #define TUL_XStatus 0xDD /*DMA status Register */ |
| #define TUL_Mask 0xE0 /*Interrupt Mask Register */ |
| #define TUL_XCtrl 0xE4 /*DMA Control Register */ |
| #define TUL_XCtrl1 0xE5 /*DMA Control Register 1 */ |
| #define TUL_XFifo 0xE8 /*DMA FIFO */ |
| |
| #define TUL_WCtrl 0xF7 /*Bus master wait state control */ |
| #define TUL_DCtrl 0xFB /*DMA delay control */ |
| |
| /*----------------------------------------------------------------------*/ |
| /* bit definition for Command register of Configuration Space Header */ |
| /*----------------------------------------------------------------------*/ |
| #define BUSMS 0x04 /* BUS MASTER Enable */ |
| #define IOSPA 0x01 /* IO Space Enable */ |
| |
| /*----------------------------------------------------------------------*/ |
| /* Command Codes of Tulip SCSI Command register */ |
| /*----------------------------------------------------------------------*/ |
| #define TSC_EN_RESEL 0x80 /* Enable Reselection */ |
| #define TSC_CMD_COMP 0x84 /* Command Complete Sequence */ |
| #define TSC_SEL 0x01 /* Select Without ATN Sequence */ |
| #define TSC_SEL_ATN 0x11 /* Select With ATN Sequence */ |
| #define TSC_SEL_ATN_DMA 0x51 /* Select With ATN Sequence with DMA */ |
| #define TSC_SEL_ATN3 0x31 /* Select With ATN3 Sequence */ |
| #define TSC_SEL_ATNSTOP 0x12 /* Select With ATN and Stop Sequence */ |
| #define TSC_SELATNSTOP 0x1E /* Select With ATN and Stop Sequence */ |
| |
| #define TSC_SEL_ATN_DIRECT_IN 0x95 /* Select With ATN Sequence */ |
| #define TSC_SEL_ATN_DIRECT_OUT 0x15 /* Select With ATN Sequence */ |
| #define TSC_SEL_ATN3_DIRECT_IN 0xB5 /* Select With ATN3 Sequence */ |
| #define TSC_SEL_ATN3_DIRECT_OUT 0x35 /* Select With ATN3 Sequence */ |
| #define TSC_XF_DMA_OUT_DIRECT 0x06 /* DMA Xfer Information out */ |
| #define TSC_XF_DMA_IN_DIRECT 0x86 /* DMA Xfer Information in */ |
| |
| #define TSC_XF_DMA_OUT 0x43 /* DMA Xfer Information out */ |
| #define TSC_XF_DMA_IN 0xC3 /* DMA Xfer Information in */ |
| #define TSC_XF_FIFO_OUT 0x03 /* FIFO Xfer Information out */ |
| #define TSC_XF_FIFO_IN 0x83 /* FIFO Xfer Information in */ |
| |
| #define TSC_MSG_ACCEPT 0x0F /* Message Accept */ |
| |
| /*----------------------------------------------------------------------*/ |
| /* bit definition for Tulip SCSI Control 0 Register */ |
| /*----------------------------------------------------------------------*/ |
| #define TSC_RST_SEQ 0x20 /* Reset sequence counter */ |
| #define TSC_FLUSH_FIFO 0x10 /* Flush FIFO */ |
| #define TSC_ABT_CMD 0x04 /* Abort command (sequence) */ |
| #define TSC_RST_CHIP 0x02 /* Reset SCSI Chip */ |
| #define TSC_RST_BUS 0x01 /* Reset SCSI Bus */ |
| |
| /*----------------------------------------------------------------------*/ |
| /* bit definition for Tulip SCSI Control 1 Register */ |
| /*----------------------------------------------------------------------*/ |
| #define TSC_EN_SCAM 0x80 /* Enable SCAM */ |
| #define TSC_TIMER 0x40 /* Select timeout unit */ |
| #define TSC_EN_SCSI2 0x20 /* SCSI-2 mode */ |
| #define TSC_PWDN 0x10 /* Power down mode */ |
| #define TSC_WIDE_CPU 0x08 /* Wide CPU */ |
| #define TSC_HW_RESELECT 0x04 /* Enable HW reselect */ |
| #define TSC_EN_BUS_OUT 0x02 /* Enable SCSI data bus out latch */ |
| #define TSC_EN_BUS_IN 0x01 /* Enable SCSI data bus in latch */ |
| |
| /*----------------------------------------------------------------------*/ |
| /* bit definition for Tulip SCSI Configuration Register */ |
| /*----------------------------------------------------------------------*/ |
| #define TSC_EN_LATCH 0x80 /* Enable phase latch */ |
| #define TSC_INITIATOR 0x40 /* Initiator mode */ |
| #define TSC_EN_SCSI_PAR 0x20 /* Enable SCSI parity */ |
| #define TSC_DMA_8BIT 0x10 /* Alternate dma 8-bits mode */ |
| #define TSC_DMA_16BIT 0x08 /* Alternate dma 16-bits mode */ |
| #define TSC_EN_WDACK 0x04 /* Enable DACK while wide SCSI xfer */ |
| #define TSC_ALT_PERIOD 0x02 /* Alternate sync period mode */ |
| #define TSC_DIS_SCSIRST 0x01 /* Disable SCSI bus reset us */ |
| |
| #define TSC_INITDEFAULT (TSC_INITIATOR | TSC_EN_LATCH | TSC_ALT_PERIOD | TSC_DIS_SCSIRST) |
| |
| #define TSC_WIDE_SCSI 0x80 /* Enable Wide SCSI */ |
| |
| /*----------------------------------------------------------------------*/ |
| /* bit definition for Tulip SCSI signal Register */ |
| /*----------------------------------------------------------------------*/ |
| #define TSC_RST_ACK 0x00 /* Release ACK signal */ |
| #define TSC_RST_ATN 0x00 /* Release ATN signal */ |
| #define TSC_RST_BSY 0x00 /* Release BSY signal */ |
| |
| #define TSC_SET_ACK 0x40 /* ACK signal */ |
| #define TSC_SET_ATN 0x08 /* ATN signal */ |
| |
| #define TSC_REQI 0x80 /* REQ signal */ |
| #define TSC_ACKI 0x40 /* ACK signal */ |
| #define TSC_BSYI 0x20 /* BSY signal */ |
| #define TSC_SELI 0x10 /* SEL signal */ |
| #define TSC_ATNI 0x08 /* ATN signal */ |
| #define TSC_MSGI 0x04 /* MSG signal */ |
| #define TSC_CDI 0x02 /* C/D signal */ |
| #define TSC_IOI 0x01 /* I/O signal */ |
| |
| |
| /*----------------------------------------------------------------------*/ |
| /* bit definition for Tulip SCSI Status 0 Register */ |
| /*----------------------------------------------------------------------*/ |
| #define TSS_INT_PENDING 0x80 /* Interrupt pending */ |
| #define TSS_SEQ_ACTIVE 0x40 /* Sequencer active */ |
| #define TSS_XFER_CNT 0x20 /* Transfer counter zero */ |
| #define TSS_FIFO_EMPTY 0x10 /* FIFO empty */ |
| #define TSS_PAR_ERROR 0x08 /* SCSI parity error */ |
| #define TSS_PH_MASK 0x07 /* SCSI phase mask */ |
| |
| /*----------------------------------------------------------------------*/ |
| /* bit definition for Tulip SCSI Status 1 Register */ |
| /*----------------------------------------------------------------------*/ |
| #define TSS_STATUS_RCV 0x08 /* Status received */ |
| #define TSS_MSG_SEND 0x40 /* Message sent */ |
| #define TSS_CMD_PH_CMP 0x20 /* command phase done */ |
| #define TSS_DATA_PH_CMP 0x10 /* Data phase done */ |
| #define TSS_STATUS_SEND 0x08 /* Status sent */ |
| #define TSS_XFER_CMP 0x04 /* Transfer completed */ |
| #define TSS_SEL_CMP 0x02 /* Selection completed */ |
| #define TSS_ARB_CMP 0x01 /* Arbitration completed */ |
| |
| /*----------------------------------------------------------------------*/ |
| /* bit definition for Tulip SCSI Status 2 Register */ |
| /*----------------------------------------------------------------------*/ |
| #define TSS_CMD_ABTED 0x80 /* Command aborted */ |
| #define TSS_OFFSET_0 0x40 /* Offset counter zero */ |
| #define TSS_FIFO_FULL 0x20 /* FIFO full */ |
| #define TSS_TIMEOUT_0 0x10 /* Timeout counter zero */ |
| #define TSS_BUSY_RLS 0x08 /* Busy release */ |
| #define TSS_PH_MISMATCH 0x04 /* Phase mismatch */ |
| #define TSS_SCSI_BUS_EN 0x02 /* SCSI data bus enable */ |
| #define TSS_SCSIRST 0x01 /* SCSI bus reset in progress */ |
| |
| /*----------------------------------------------------------------------*/ |
| /* bit definition for Tulip SCSI Interrupt Register */ |
| /*----------------------------------------------------------------------*/ |
| #define TSS_RESEL_INT 0x80 /* Reselected interrupt */ |
| #define TSS_SEL_TIMEOUT 0x40 /* Selected/reselected timeout */ |
| #define TSS_BUS_SERV 0x20 |
| #define TSS_SCSIRST_INT 0x10 /* SCSI bus reset detected */ |
| #define TSS_DISC_INT 0x08 /* Disconnected interrupt */ |
| #define TSS_SEL_INT 0x04 /* Select interrupt */ |
| #define TSS_SCAM_SEL 0x02 /* SCAM selected */ |
| #define TSS_FUNC_COMP 0x01 |
| |
| /*----------------------------------------------------------------------*/ |
| /* SCSI Phase Codes. */ |
| /*----------------------------------------------------------------------*/ |
| #define DATA_OUT 0 |
| #define DATA_IN 1 /* 4 */ |
| #define CMD_OUT 2 |
| #define STATUS_IN 3 /* 6 */ |
| #define MSG_OUT 6 /* 3 */ |
| #define MSG_IN 7 |
| |
| |
| |
| /*----------------------------------------------------------------------*/ |
| /* Command Codes of Tulip xfer Command register */ |
| /*----------------------------------------------------------------------*/ |
| #define TAX_X_FORC 0x02 |
| #define TAX_X_ABT 0x04 |
| #define TAX_X_CLR_FIFO 0x08 |
| |
| #define TAX_X_IN 0x21 |
| #define TAX_X_OUT 0x01 |
| #define TAX_SG_IN 0xA1 |
| #define TAX_SG_OUT 0x81 |
| |
| /*----------------------------------------------------------------------*/ |
| /* Tulip Interrupt Register */ |
| /*----------------------------------------------------------------------*/ |
| #define XCMP 0x01 |
| #define FCMP 0x02 |
| #define XABT 0x04 |
| #define XERR 0x08 |
| #define SCMP 0x10 |
| #define IPEND 0x80 |
| |
| /*----------------------------------------------------------------------*/ |
| /* Tulip DMA Status Register */ |
| /*----------------------------------------------------------------------*/ |
| #define XPEND 0x01 /* Transfer pending */ |
| #define FEMPTY 0x02 /* FIFO empty */ |
| |
| |
| |
| /*----------------------------------------------------------------------*/ |
| /* bit definition for TUL_GCTRL */ |
| /*----------------------------------------------------------------------*/ |
| #define EXTSG 0x80 |
| #define EXTAD 0x60 |
| #define SEG4K 0x08 |
| #define EEPRG 0x04 |
| #define MRMUL 0x02 |
| |
| /*----------------------------------------------------------------------*/ |
| /* bit definition for TUL_NVRAM */ |
| /*----------------------------------------------------------------------*/ |
| #define SE2CS 0x08 |
| #define SE2CLK 0x04 |
| #define SE2DO 0x02 |
| #define SE2DI 0x01 |
| |
| |
| /************************************************************************/ |
| /* Scatter-Gather Element Structure */ |
| /************************************************************************/ |
| typedef struct SG_Struc { |
| U32 SG_Ptr; /* Data Pointer */ |
| U32 SG_Len; /* Data Length */ |
| } SG; |
| |
| /*********************************************************************** |
| SCSI Control Block |
| ************************************************************************/ |
| typedef struct Scsi_Ctrl_Blk { |
| struct Scsi_Ctrl_Blk *SCB_NxtScb; |
| UBYTE SCB_Status; /*4 */ |
| UBYTE SCB_NxtStat; /*5 */ |
| UBYTE SCB_Mode; /*6 */ |
| UBYTE SCB_Msgin; /*7 SCB_Res0 */ |
| UWORD SCB_SGIdx; /*8 */ |
| UWORD SCB_SGMax; /*A */ |
| #ifdef ALPHA |
| U32 SCB_Reserved[2]; /*C */ |
| #else |
| U32 SCB_Reserved[3]; /*C */ |
| #endif |
| |
| U32 SCB_XferLen; /*18 Current xfer len */ |
| U32 SCB_TotXLen; /*1C Total xfer len */ |
| U32 SCB_PAddr; /*20 SCB phy. Addr. */ |
| |
| UBYTE SCB_Opcode; /*24 SCB command code */ |
| UBYTE SCB_Flags; /*25 SCB Flags */ |
| UBYTE SCB_Target; /*26 Target Id */ |
| UBYTE SCB_Lun; /*27 Lun */ |
| U32 SCB_BufPtr; /*28 Data Buffer Pointer */ |
| U32 SCB_BufLen; /*2C Data Allocation Length */ |
| UBYTE SCB_SGLen; /*30 SG list # */ |
| UBYTE SCB_SenseLen; /*31 Sense Allocation Length */ |
| UBYTE SCB_HaStat; /*32 */ |
| UBYTE SCB_TaStat; /*33 */ |
| UBYTE SCB_CDBLen; /*34 CDB Length */ |
| UBYTE SCB_Ident; /*35 Identify */ |
| UBYTE SCB_TagMsg; /*36 Tag Message */ |
| UBYTE SCB_TagId; /*37 Queue Tag */ |
| UBYTE SCB_CDB[12]; /*38 */ |
| U32 SCB_SGPAddr; /*44 SG List/Sense Buf phy. Addr. */ |
| U32 SCB_SensePtr; /*48 Sense data pointer */ |
| void (*SCB_Post) (BYTE *, BYTE *); /*4C POST routine */ |
| struct scsi_cmnd *SCB_Srb; /*50 SRB Pointer */ |
| SG SCB_SGList[TOTAL_SG_ENTRY]; /*54 Start of SG list */ |
| } SCB; |
| |
| /* Bit Definition for SCB_Status */ |
| #define SCB_RENT 0x01 |
| #define SCB_PEND 0x02 |
| #define SCB_CONTIG 0x04 /* Contigent Allegiance */ |
| #define SCB_SELECT 0x08 |
| #define SCB_BUSY 0x10 |
| #define SCB_DONE 0x20 |
| |
| |
| /* Opcodes of SCB_Opcode */ |
| #define ExecSCSI 0x1 |
| #define BusDevRst 0x2 |
| #define AbortCmd 0x3 |
| |
| |
| /* Bit Definition for SCB_Mode */ |
| #define SCM_RSENS 0x01 /* request sense mode */ |
| |
| |
| /* Bit Definition for SCB_Flags */ |
| #define SCF_DONE 0x01 |
| #define SCF_POST 0x02 |
| #define SCF_SENSE 0x04 |
| #define SCF_DIR 0x18 |
| #define SCF_NO_DCHK 0x00 |
| #define SCF_DIN 0x08 |
| #define SCF_DOUT 0x10 |
| #define SCF_NO_XF 0x18 |
| #define SCF_WR_VF 0x20 /* Write verify turn on */ |
| #define SCF_POLL 0x40 |
| #define SCF_SG 0x80 |
| |
| /* Error Codes for SCB_HaStat */ |
| #define HOST_SEL_TOUT 0x11 |
| #define HOST_DO_DU 0x12 |
| #define HOST_BUS_FREE 0x13 |
| #define HOST_BAD_PHAS 0x14 |
| #define HOST_INV_CMD 0x16 |
| #define HOST_ABORTED 0x1A /* 07/21/98 */ |
| #define HOST_SCSI_RST 0x1B |
| #define HOST_DEV_RST 0x1C |
| |
| /* Error Codes for SCB_TaStat */ |
| #define TARGET_CHKCOND 0x02 |
| #define TARGET_BUSY 0x08 |
| #define INI_QUEUE_FULL 0x28 |
| |
| /* SCSI MESSAGE */ |
| #define MSG_COMP 0x00 |
| #define MSG_EXTEND 0x01 |
| #define MSG_SDP 0x02 |
| #define MSG_RESTORE 0x03 |
| #define MSG_DISC 0x04 |
| #define MSG_IDE 0x05 |
| #define MSG_ABORT 0x06 |
| #define MSG_REJ 0x07 |
| #define MSG_NOP 0x08 |
| #define MSG_PARITY 0x09 |
| #define MSG_LINK_COMP 0x0A |
| #define MSG_LINK_FLAG 0x0B |
| #define MSG_DEVRST 0x0C |
| #define MSG_ABORT_TAG 0x0D |
| |
| /* Queue tag msg: Simple_quque_tag, Head_of_queue_tag, Ordered_queue_tag */ |
| #define MSG_STAG 0x20 |
| #define MSG_HTAG 0x21 |
| #define MSG_OTAG 0x22 |
| |
| #define MSG_IGNOREWIDE 0x23 |
| |
| #define MSG_IDENT 0x80 |
| |
| /*********************************************************************** |
| Target Device Control Structure |
| **********************************************************************/ |
| |
| typedef struct Tar_Ctrl_Struc { |
| UWORD TCS_Flags; /* 0 */ |
| UBYTE TCS_JS_Period; /* 2 */ |
| UBYTE TCS_SConfig0; /* 3 */ |
| |
| UWORD TCS_DrvFlags; /* 4 */ |
| UBYTE TCS_DrvHead; /* 6 */ |
| UBYTE TCS_DrvSector; /* 7 */ |
| } TCS; |
| |
| /*********************************************************************** |
| Target Device Control Structure |
| **********************************************************************/ |
| |
| /* Bit Definition for TCF_Flags */ |
| #define TCF_SCSI_RATE 0x0007 |
| #define TCF_EN_DISC 0x0008 |
| #define TCF_NO_SYNC_NEGO 0x0010 |
| #define TCF_NO_WDTR 0x0020 |
| #define TCF_EN_255 0x0040 |
| #define TCF_EN_START 0x0080 |
| #define TCF_WDTR_DONE 0x0100 |
| #define TCF_SYNC_DONE 0x0200 |
| #define TCF_BUSY 0x0400 |
| |
| |
| /* Bit Definition for TCF_DrvFlags */ |
| #define TCF_DRV_BUSY 0x01 /* Indicate target busy(driver) */ |
| #define TCF_DRV_EN_TAG 0x0800 |
| #define TCF_DRV_255_63 0x0400 |
| |
| typedef struct I91u_Adpt_Struc { |
| UWORD ADPT_BIOS; /* 0 */ |
| UWORD ADPT_BASE; /* 1 */ |
| UBYTE ADPT_Bus; /* 2 */ |
| UBYTE ADPT_Device; /* 3 */ |
| UBYTE ADPT_INTR; /* 4 */ |
| } INI_ADPT_STRUCT; |
| |
| |
| /*********************************************************************** |
| Host Adapter Control Structure |
| ************************************************************************/ |
| typedef struct Ha_Ctrl_Struc { |
| UWORD HCS_Base; /* 00 */ |
| UWORD HCS_BIOS; /* 02 */ |
| UBYTE HCS_Intr; /* 04 */ |
| UBYTE HCS_SCSI_ID; /* 05 */ |
| UBYTE HCS_MaxTar; /* 06 */ |
| UBYTE HCS_NumScbs; /* 07 */ |
| |
| UBYTE HCS_Flags; /* 08 */ |
| UBYTE HCS_Index; /* 09 */ |
| UBYTE HCS_HaId; /* 0A */ |
| UBYTE HCS_Config; /* 0B */ |
| UWORD HCS_IdMask; /* 0C */ |
| UBYTE HCS_Semaph; /* 0E */ |
| UBYTE HCS_Phase; /* 0F */ |
| UBYTE HCS_JSStatus0; /* 10 */ |
| UBYTE HCS_JSInt; /* 11 */ |
| UBYTE HCS_JSStatus1; /* 12 */ |
| UBYTE HCS_SConf1; /* 13 */ |
| |
| UBYTE HCS_Msg[8]; /* 14 */ |
| SCB *HCS_NxtAvail; /* 1C */ |
| SCB *HCS_Scb; /* 20 */ |
| SCB *HCS_ScbEnd; /* 24 */ |
| SCB *HCS_NxtPend; /* 28 */ |
| SCB *HCS_NxtContig; /* 2C */ |
| SCB *HCS_ActScb; /* 30 */ |
| TCS *HCS_ActTcs; /* 34 */ |
| |
| SCB *HCS_FirstAvail; /* 38 */ |
| SCB *HCS_LastAvail; /* 3C */ |
| SCB *HCS_FirstPend; /* 40 */ |
| SCB *HCS_LastPend; /* 44 */ |
| SCB *HCS_FirstBusy; /* 48 */ |
| SCB *HCS_LastBusy; /* 4C */ |
| SCB *HCS_FirstDone; /* 50 */ |
| SCB *HCS_LastDone; /* 54 */ |
| UBYTE HCS_MaxTags[16]; /* 58 */ |
| UBYTE HCS_ActTags[16]; /* 68 */ |
| TCS HCS_Tcs[MAX_TARGETS]; /* 78 */ |
| spinlock_t HCS_AvailLock; |
| spinlock_t HCS_SemaphLock; |
| struct pci_dev *pci_dev; |
| } HCS; |
| |
| /* Bit Definition for HCB_Config */ |
| #define HCC_SCSI_RESET 0x01 |
| #define HCC_EN_PAR 0x02 |
| #define HCC_ACT_TERM1 0x04 |
| #define HCC_ACT_TERM2 0x08 |
| #define HCC_AUTO_TERM 0x10 |
| #define HCC_EN_PWR 0x80 |
| |
| /* Bit Definition for HCB_Flags */ |
| #define HCF_EXPECT_DISC 0x01 |
| #define HCF_EXPECT_SELECT 0x02 |
| #define HCF_EXPECT_RESET 0x10 |
| #define HCF_EXPECT_DONE_DISC 0x20 |
| |
| /****************************************************************** |
| Serial EEProm |
| *******************************************************************/ |
| |
| typedef struct _NVRAM_SCSI { /* SCSI channel configuration */ |
| UCHAR NVM_ChSCSIID; /* 0Ch -> Channel SCSI ID */ |
| UCHAR NVM_ChConfig1; /* 0Dh -> Channel config 1 */ |
| UCHAR NVM_ChConfig2; /* 0Eh -> Channel config 2 */ |
| UCHAR NVM_NumOfTarg; /* 0Fh -> Number of SCSI target */ |
| /* SCSI target configuration */ |
| UCHAR NVM_Targ0Config; /* 10h -> Target 0 configuration */ |
| UCHAR NVM_Targ1Config; /* 11h -> Target 1 configuration */ |
| UCHAR NVM_Targ2Config; /* 12h -> Target 2 configuration */ |
| UCHAR NVM_Targ3Config; /* 13h -> Target 3 configuration */ |
| UCHAR NVM_Targ4Config; /* 14h -> Target 4 configuration */ |
| UCHAR NVM_Targ5Config; /* 15h -> Target 5 configuration */ |
| UCHAR NVM_Targ6Config; /* 16h -> Target 6 configuration */ |
| UCHAR NVM_Targ7Config; /* 17h -> Target 7 configuration */ |
| UCHAR NVM_Targ8Config; /* 18h -> Target 8 configuration */ |
| UCHAR NVM_Targ9Config; /* 19h -> Target 9 configuration */ |
| UCHAR NVM_TargAConfig; /* 1Ah -> Target A configuration */ |
| UCHAR NVM_TargBConfig; /* 1Bh -> Target B configuration */ |
| UCHAR NVM_TargCConfig; /* 1Ch -> Target C configuration */ |
| UCHAR NVM_TargDConfig; /* 1Dh -> Target D configuration */ |
| UCHAR NVM_TargEConfig; /* 1Eh -> Target E configuration */ |
| UCHAR NVM_TargFConfig; /* 1Fh -> Target F configuration */ |
| } NVRAM_SCSI; |
| |
| typedef struct _NVRAM { |
| /*----------header ---------------*/ |
| USHORT NVM_Signature; /* 0,1: Signature */ |
| UCHAR NVM_Size; /* 2: Size of data structure */ |
| UCHAR NVM_Revision; /* 3: Revision of data structure */ |
| /* ----Host Adapter Structure ---- */ |
| UCHAR NVM_ModelByte0; /* 4: Model number (byte 0) */ |
| UCHAR NVM_ModelByte1; /* 5: Model number (byte 1) */ |
| UCHAR NVM_ModelInfo; /* 6: Model information */ |
| UCHAR NVM_NumOfCh; /* 7: Number of SCSI channel */ |
| UCHAR NVM_BIOSConfig1; /* 8: BIOS configuration 1 */ |
| UCHAR NVM_BIOSConfig2; /* 9: BIOS configuration 2 */ |
| UCHAR NVM_HAConfig1; /* A: Hoat adapter configuration 1 */ |
| UCHAR NVM_HAConfig2; /* B: Hoat adapter configuration 2 */ |
| NVRAM_SCSI NVM_SCSIInfo[2]; |
| UCHAR NVM_reserved[10]; |
| /* ---------- CheckSum ---------- */ |
| USHORT NVM_CheckSum; /* 0x3E, 0x3F: Checksum of NVRam */ |
| } NVRAM, *PNVRAM; |
| |
| /* Bios Configuration for nvram->BIOSConfig1 */ |
| #define NBC1_ENABLE 0x01 /* BIOS enable */ |
| #define NBC1_8DRIVE 0x02 /* Support more than 2 drives */ |
| #define NBC1_REMOVABLE 0x04 /* Support removable drive */ |
| #define NBC1_INT19 0x08 /* Intercept int 19h */ |
| #define NBC1_BIOSSCAN 0x10 /* Dynamic BIOS scan */ |
| #define NBC1_LUNSUPPORT 0x40 /* Support LUN */ |
| |
| /* HA Configuration Byte 1 */ |
| #define NHC1_BOOTIDMASK 0x0F /* Boot ID number */ |
| #define NHC1_LUNMASK 0x70 /* Boot LUN number */ |
| #define NHC1_CHANMASK 0x80 /* Boot Channel number */ |
| |
| /* Bit definition for nvram->SCSIconfig1 */ |
| #define NCC1_BUSRESET 0x01 /* Reset SCSI bus at power up */ |
| #define NCC1_PARITYCHK 0x02 /* SCSI parity enable */ |
| #define NCC1_ACTTERM1 0x04 /* Enable active terminator 1 */ |
| #define NCC1_ACTTERM2 0x08 /* Enable active terminator 2 */ |
| #define NCC1_AUTOTERM 0x10 /* Enable auto terminator */ |
| #define NCC1_PWRMGR 0x80 /* Enable power management */ |
| |
| /* Bit definition for SCSI Target configuration byte */ |
| #define NTC_DISCONNECT 0x08 /* Enable SCSI disconnect */ |
| #define NTC_SYNC 0x10 /* SYNC_NEGO */ |
| #define NTC_NO_WDTR 0x20 /* SYNC_NEGO */ |
| #define NTC_1GIGA 0x40 /* 255 head / 63 sectors (64/32) */ |
| #define NTC_SPINUP 0x80 /* Start disk drive */ |
| |
| /* Default NVRam values */ |
| #define INI_SIGNATURE 0xC925 |
| #define NBC1_DEFAULT (NBC1_ENABLE) |
| #define NCC1_DEFAULT (NCC1_BUSRESET | NCC1_AUTOTERM | NCC1_PARITYCHK) |
| #define NTC_DEFAULT (NTC_NO_WDTR | NTC_1GIGA | NTC_DISCONNECT) |
| |
| /* SCSI related definition */ |
| #define DISC_NOT_ALLOW 0x80 /* Disconnect is not allowed */ |
| #define DISC_ALLOW 0xC0 /* Disconnect is allowed */ |
| #define SCSICMD_RequestSense 0x03 |
| |
| typedef struct _HCSinfo { |
| ULONG base; |
| UCHAR vec; |
| UCHAR bios; /* High byte of BIOS address */ |
| USHORT BaseAndBios; /* high byte: pHcsInfo->bios,low byte:pHcsInfo->base */ |
| } HCSINFO; |
| |
| #define TUL_RD(x,y) (UCHAR)(inb( (int)((ULONG)(x+y)) )) |
| #define TUL_RDLONG(x,y) (ULONG)(inl((int)((ULONG)(x+y)) )) |
| #define TUL_WR( adr,data) outb( (UCHAR)(data), (int)(adr)) |
| #define TUL_WRSHORT(adr,data) outw( (UWORD)(data), (int)(adr)) |
| #define TUL_WRLONG( adr,data) outl( (ULONG)(data), (int)(adr)) |
| |
| #define SCSI_ABORT_SNOOZE 0 |
| #define SCSI_ABORT_SUCCESS 1 |
| #define SCSI_ABORT_PENDING 2 |
| #define SCSI_ABORT_BUSY 3 |
| #define SCSI_ABORT_NOT_RUNNING 4 |
| #define SCSI_ABORT_ERROR 5 |
| |
| #define SCSI_RESET_SNOOZE 0 |
| #define SCSI_RESET_PUNT 1 |
| #define SCSI_RESET_SUCCESS 2 |
| #define SCSI_RESET_PENDING 3 |
| #define SCSI_RESET_WAKEUP 4 |
| #define SCSI_RESET_NOT_RUNNING 5 |
| #define SCSI_RESET_ERROR 6 |
| |
| #define SCSI_RESET_SYNCHRONOUS 0x01 |
| #define SCSI_RESET_ASYNCHRONOUS 0x02 |
| #define SCSI_RESET_SUGGEST_BUS_RESET 0x04 |
| #define SCSI_RESET_SUGGEST_HOST_RESET 0x08 |
| |
| #define SCSI_RESET_BUS_RESET 0x100 |
| #define SCSI_RESET_HOST_RESET 0x200 |
| #define SCSI_RESET_ACTION 0xff |
| |