| menuconfig REGULATOR |
| bool "Voltage and Current Regulator Support" |
| help |
| Generic Voltage and Current Regulator support. |
| |
| This framework is designed to provide a generic interface to voltage |
| and current regulators within the Linux kernel. It's intended to |
| provide voltage and current control to client or consumer drivers and |
| also provide status information to user space applications through a |
| sysfs interface. |
| |
| The intention is to allow systems to dynamically control regulator |
| output in order to save power and prolong battery life. This applies |
| to both voltage regulators (where voltage output is controllable) and |
| current sinks (where current output is controllable). |
| |
| This framework safely compiles out if not selected so that client |
| drivers can still be used in systems with no software controllable |
| regulators. |
| |
| If unsure, say no. |
| |
| if REGULATOR |
| |
| config REGULATOR_DEBUG |
| bool "Regulator debug support" |
| help |
| Say yes here to enable debugging support. |
| |
| config REGULATOR_DUMMY |
| bool "Provide a dummy regulator if regulator lookups fail" |
| help |
| If this option is enabled then when a regulator lookup fails |
| and the board has not specified that it has provided full |
| constraints then the regulator core will provide an always |
| enabled dummy regulator will be provided, allowing consumer |
| drivers to continue. |
| |
| A warning will be generated when this substitution is done. |
| |
| config REGULATOR_FIXED_VOLTAGE |
| tristate "Fixed voltage regulator support" |
| help |
| This driver provides support for fixed voltage regulators, |
| useful for systems which use a combination of software |
| managed regulators and simple non-configurable regulators. |
| |
| config REGULATOR_VIRTUAL_CONSUMER |
| tristate "Virtual regulator consumer support" |
| help |
| This driver provides a virtual consumer for the voltage and |
| current regulator API which provides sysfs controls for |
| configuring the supplies requested. This is mainly useful |
| for test purposes. |
| |
| If unsure, say no. |
| |
| config REGULATOR_USERSPACE_CONSUMER |
| tristate "Userspace regulator consumer support" |
| help |
| There are some classes of devices that are controlled entirely |
| from user space. Userspace consumer driver provides ability to |
| control power supplies for such devices. |
| |
| If unsure, say no. |
| |
| config REGULATOR_GPIO |
| tristate "GPIO regulator support" |
| depends on GENERIC_GPIO |
| help |
| This driver provides support for regulators that can be |
| controlled via gpios. |
| It is capable of supporting current and voltage regulators |
| and the platform has to provide a mapping of GPIO-states |
| to target volts/amps. |
| |
| config REGULATOR_AD5398 |
| tristate "Analog Devices AD5398/AD5821 regulators" |
| depends on I2C |
| help |
| This driver supports AD5398 and AD5821 current regulator chips. |
| If building into module, its name is ad5398.ko. |
| |
| config REGULATOR_AAT2870 |
| tristate "AnalogicTech AAT2870 Regulators" |
| depends on MFD_AAT2870_CORE |
| help |
| If you have a AnalogicTech AAT2870 say Y to enable the |
| regulator driver. |
| |
| config REGULATOR_DA903X |
| tristate "Dialog Semiconductor DA9030/DA9034 regulators" |
| depends on PMIC_DA903X |
| help |
| Say y here to support the BUCKs and LDOs regulators found on |
| Dialog Semiconductor DA9030/DA9034 PMIC. |
| |
| config REGULATOR_DA9052 |
| tristate "Dialog Semiconductor DA9052/DA9053 regulators" |
| depends on PMIC_DA9052 |
| help |
| This driver supports the voltage regulators of DA9052-BC and |
| DA9053-AA/Bx PMIC. |
| |
| config REGULATOR_FAN53555 |
| tristate "Fairchild FAN53555 Regulator" |
| depends on I2C |
| select REGMAP_I2C |
| help |
| This driver supports Fairchild FAN53555 Digitally Programmable |
| TinyBuck Regulator. The FAN53555 is a step-down switching voltage |
| regulator that delivers a digitally programmable output from an |
| input voltage supply of 2.5V to 5.5V. The output voltage is |
| programmed through an I2C interface. |
| |
| config REGULATOR_ANATOP |
| tristate "Freescale i.MX on-chip ANATOP LDO regulators" |
| depends on MFD_ANATOP |
| help |
| Say y here to support Freescale i.MX on-chip ANATOP LDOs |
| regulators. It is recommended that this option be |
| enabled on i.MX6 platform. |
| |
| config REGULATOR_MC13XXX_CORE |
| tristate |
| |
| config REGULATOR_MC13783 |
| tristate "Freescale MC13783 regulator driver" |
| depends on MFD_MC13783 |
| select REGULATOR_MC13XXX_CORE |
| help |
| Say y here to support the regulators found on the Freescale MC13783 |
| PMIC. |
| |
| config REGULATOR_MC13892 |
| tristate "Freescale MC13892 regulator driver" |
| depends on MFD_MC13XXX |
| select REGULATOR_MC13XXX_CORE |
| help |
| Say y here to support the regulators found on the Freescale MC13892 |
| PMIC. |
| |
| config REGULATOR_ISL6271A |
| tristate "Intersil ISL6271A Power regulator" |
| depends on I2C |
| help |
| This driver supports ISL6271A voltage regulator chip. |
| |
| config REGULATOR_88PM8607 |
| bool "Marvell 88PM8607 Power regulators" |
| depends on MFD_88PM860X=y |
| help |
| This driver supports 88PM8607 voltage regulator chips. |
| |
| config REGULATOR_MAX1586 |
| tristate "Maxim 1586/1587 voltage regulator" |
| depends on I2C |
| help |
| This driver controls a Maxim 1586 or 1587 voltage output |
| regulator via I2C bus. The provided regulator is suitable |
| for PXA27x chips to control VCC_CORE and VCC_USIM voltages. |
| |
| config REGULATOR_MAX8649 |
| tristate "Maxim 8649 voltage regulator" |
| depends on I2C |
| select REGMAP_I2C |
| help |
| This driver controls a Maxim 8649 voltage output regulator via |
| I2C bus. |
| |
| config REGULATOR_MAX8660 |
| tristate "Maxim 8660/8661 voltage regulator" |
| depends on I2C |
| help |
| This driver controls a Maxim 8660/8661 voltage output |
| regulator via I2C bus. |
| |
| config REGULATOR_MAX8925 |
| tristate "Maxim MAX8925 Power Management IC" |
| depends on MFD_MAX8925 |
| help |
| Say y here to support the voltage regulaltor of Maxim MAX8925 PMIC. |
| |
| config REGULATOR_MAX8952 |
| tristate "Maxim MAX8952 Power Management IC" |
| depends on I2C |
| help |
| This driver controls a Maxim 8952 voltage output regulator |
| via I2C bus. Maxim 8952 has one voltage output and supports 4 DVS |
| modes ranging from 0.77V to 1.40V by 0.01V steps. |
| |
| config REGULATOR_MAX8997 |
| tristate "Maxim 8997/8966 regulator" |
| depends on MFD_MAX8997 |
| help |
| This driver controls a Maxim 8997/8966 regulator |
| via I2C bus. The provided regulator is suitable for S5PC110, |
| S5PV210, and Exynos-4 chips to control VCC_CORE and |
| VCC_USIM voltages. |
| |
| config REGULATOR_MAX8998 |
| tristate "Maxim 8998 voltage regulator" |
| depends on MFD_MAX8998 |
| help |
| This driver controls a Maxim 8998 voltage output regulator |
| via I2C bus. The provided regulator is suitable for S3C6410 |
| and S5PC1XX chips to control VCC_CORE and VCC_USIM voltages. |
| |
| config REGULATOR_ONSEMI_NCP6335D |
| tristate "OnSemi NCP6335D regulator support" |
| depends on I2C |
| help |
| This driver supports the OnSemi NCP6335D switching voltage regulator |
| (buck convertor). The regulator is controlled using an I2C interface |
| and supports a programmable voltage range from 0.6V to 1.4V in steps |
| of 6.25mV. |
| |
| config REGULATOR_PCAP |
| tristate "Motorola PCAP2 regulator driver" |
| depends on EZX_PCAP |
| help |
| This driver provides support for the voltage regulators of the |
| PCAP2 PMIC. |
| |
| config REGULATOR_LP3971 |
| tristate "National Semiconductors LP3971 PMIC regulator driver" |
| depends on I2C |
| help |
| Say Y here to support the voltage regulators and convertors |
| on National Semiconductors LP3971 PMIC |
| |
| config REGULATOR_LP3972 |
| tristate "National Semiconductors LP3972 PMIC regulator driver" |
| depends on I2C |
| help |
| Say Y here to support the voltage regulators and convertors |
| on National Semiconductors LP3972 PMIC |
| |
| config REGULATOR_PCF50633 |
| tristate "NXP PCF50633 regulator driver" |
| depends on MFD_PCF50633 |
| help |
| Say Y here to support the voltage regulators and convertors |
| on PCF50633 |
| |
| config REGULATOR_S5M8767 |
| tristate "Samsung S5M8767A voltage regulator" |
| depends on MFD_S5M_CORE |
| help |
| This driver supports a Samsung S5M8767A voltage output regulator |
| via I2C bus. S5M8767A have 9 Bucks and 28 LDOs output and |
| supports DVS mode with 8bits of output voltage control. |
| |
| config REGULATOR_AB3100 |
| tristate "ST-Ericsson AB3100 Regulator functions" |
| depends on AB3100_CORE |
| default y if AB3100_CORE |
| help |
| These regulators correspond to functionality in the |
| AB3100 analog baseband dealing with power regulators |
| for the system. |
| |
| config REGULATOR_AB8500 |
| bool "ST-Ericsson AB8500 Power Regulators" |
| depends on AB8500_CORE |
| help |
| This driver supports the regulators found on the ST-Ericsson mixed |
| signal AB8500 PMIC |
| |
| config REGULATOR_DBX500_PRCMU |
| bool |
| |
| config REGULATOR_DB8500_PRCMU |
| bool "ST-Ericsson DB8500 Voltage Domain Regulators" |
| depends on MFD_DB8500_PRCMU |
| select REGULATOR_DBX500_PRCMU |
| help |
| This driver supports the voltage domain regulators controlled by the |
| DB8500 PRCMU |
| |
| config REGULATOR_TPS6105X |
| tristate "TI TPS6105X Power regulators" |
| depends on TPS6105X |
| default y if TPS6105X |
| help |
| This driver supports TPS61050/TPS61052 voltage regulator chips. |
| It is a single boost converter primarily for white LEDs and |
| audio amplifiers. |
| |
| config REGULATOR_TPS62360 |
| tristate "TI TPS62360 Power Regulator" |
| depends on I2C |
| select REGMAP_I2C |
| help |
| This driver supports TPS62360 voltage regulator chip. This |
| regulator is meant for processor core supply. This chip is |
| high-frequency synchronous step down dc-dc converter optimized |
| for battery-powered portable applications. |
| |
| config REGULATOR_TPS65023 |
| tristate "TI TPS65023 Power regulators" |
| depends on I2C |
| select REGMAP_I2C |
| help |
| This driver supports TPS65023 voltage regulator chips. TPS65023 provides |
| three step-down converters and two general-purpose LDO voltage regulators. |
| It supports TI's software based Class-2 SmartReflex implementation. |
| |
| config REGULATOR_TPS6507X |
| tristate "TI TPS6507X Power regulators" |
| depends on I2C |
| help |
| This driver supports TPS6507X voltage regulator chips. TPS6507X provides |
| three step-down converters and two general-purpose LDO voltage regulators. |
| It supports TI's software based Class-2 SmartReflex implementation. |
| |
| config REGULATOR_TPS65217 |
| tristate "TI TPS65217 Power regulators" |
| depends on MFD_TPS65217 |
| help |
| This driver supports TPS65217 voltage regulator chips. TPS65217 |
| provides three step-down converters and four general-purpose LDO |
| voltage regulators. It supports software based voltage control |
| for different voltage domains |
| |
| config REGULATOR_TPS6524X |
| tristate "TI TPS6524X Power regulators" |
| depends on SPI |
| help |
| This driver supports TPS6524X voltage regulator chips. TPS6524X |
| provides three step-down converters and two general-purpose LDO |
| voltage regulators. This device is interfaced using a customized |
| serial interface currently supported on the sequencer serial |
| port controller. |
| |
| config REGULATOR_TPS6586X |
| tristate "TI TPS6586X Power regulators" |
| depends on MFD_TPS6586X |
| help |
| This driver supports TPS6586X voltage regulator chips. |
| |
| config REGULATOR_TPS65910 |
| tristate "TI TPS65910/TPS65911 Power Regulators" |
| depends on MFD_TPS65910 |
| help |
| This driver supports TPS65910/TPS65911 voltage regulator chips. |
| |
| config REGULATOR_TPS65912 |
| tristate "TI TPS65912 Power regulator" |
| depends on (MFD_TPS65912_I2C || MFD_TPS65912_SPI) |
| help |
| This driver supports TPS65912 voltage regulator chip. |
| |
| config REGULATOR_TWL4030 |
| bool "TI TWL4030/TWL5030/TWL6030/TPS659x0 PMIC" |
| depends on TWL4030_CORE |
| help |
| This driver supports the voltage regulators provided by |
| this family of companion chips. |
| |
| config REGULATOR_WM831X |
| tristate "Wolfson Microelectronics WM831x PMIC regulators" |
| depends on MFD_WM831X |
| help |
| Support the voltage and current regulators of the WM831x series |
| of PMIC devices. |
| |
| config REGULATOR_WM8350 |
| tristate "Wolfson Microelectronics WM8350 AudioPlus PMIC" |
| depends on MFD_WM8350 |
| help |
| This driver provides support for the voltage and current regulators |
| of the WM8350 AudioPlus PMIC. |
| |
| config REGULATOR_WM8400 |
| tristate "Wolfson Microelectronics WM8400 AudioPlus PMIC" |
| depends on MFD_WM8400 |
| help |
| This driver provides support for the voltage regulators of the |
| WM8400 AudioPlus PMIC. |
| |
| config REGULATOR_WM8994 |
| tristate "Wolfson Microelectronics WM8994 CODEC" |
| depends on MFD_WM8994 |
| help |
| This driver provides support for the voltage regulators on the |
| WM8994 CODEC. |
| |
| config REGULATOR_PMIC8058 |
| tristate "PMIC8058 regulator driver" |
| depends on PMIC8058 && (ARCH_MSM8X60 || ARCH_FSM9XXX) |
| default y if PMIC8058 && (ARCH_MSM8X60 || ARCH_FSM9XXX) |
| help |
| Say Y here to support the voltage regulators on PMIC8058 |
| |
| config REGULATOR_PMIC8901 |
| tristate "PMIC8901 regulator driver" |
| depends on PMIC8901 && ARCH_MSM8X60 |
| default y if PMIC8901 && ARCH_MSM8X60 |
| help |
| Say Y here to support the voltage regulators on PMIC8901 |
| |
| config REGULATOR_PM8XXX |
| tristate "Qualcomm PM8XXX PMIC Voltage regulators" |
| depends on MFD_PM8XXX |
| help |
| This driver supports voltage regulators in Qualcomm PM8XXX PMIC chips. |
| PM8XXX chips provide several different varieties of LDO and switching |
| regulators. They also provide negative charge pumps and voltage |
| switches. |
| |
| config REGULATOR_MSM_GPIO |
| tristate "MSM GPIO regulator" |
| depends on GPIOLIB |
| help |
| This driver provides a regulator wrapper around a GPIO pin that is set |
| to output. It is intended to be used for GPIO pins that provide the |
| enable signal to a physical regulator. The GPIO enable signal can |
| be configured to be active high (default) or active low. |
| |
| config REGULATOR_PM8058_XO |
| tristate "PM8058 XO Buffer driver" |
| depends on PMIC8058 |
| default n |
| help |
| This driver supports xo buffer control in the Qualcomm PM8058 PMIC |
| chip. It is only supposed to be used when Linux on application |
| processor is the master in control of XO buffers. |
| |
| config REGULATOR_STUB |
| tristate "Stub Regulator" |
| help |
| This driver adds stub regulator support. The driver is absent of any |
| real hardware based implementation. It allows for clients to register |
| their regulator device constraints and use all of the standard |
| regulator interfaces. This is useful for bringing up new platforms |
| when the real hardware based implementation may not be yet available. |
| Clients can use the real regulator device names with proper |
| constraint checking while the real driver is being developed. |
| |
| config REGULATOR_QPNP |
| depends on SPMI |
| depends on OF_SPMI |
| tristate "Qualcomm QPNP regulator support" |
| help |
| This driver supports voltage regulators in Qualcomm PMIC chips which |
| comply with QPNP. QPNP is a SPMI based PMIC implementation. These |
| chips provide several different varieties of LDO and switching |
| regulators. They also provide voltage switches and boost regulators. |
| |
| endif |
| |