blob: a66e2c3a221b117059e892286e609c5e3a825db9 [file] [log] [blame]
/*
* pata_hpt3x3 - HPT3x3 driver
* (c) Copyright 2005-2006 Red Hat
*
* Was pata_hpt34x but the naming was confusing as it supported the
* 343 and 363 so it has been renamed.
*
* Based on:
* linux/drivers/ide/pci/hpt34x.c Version 0.40 Sept 10, 2002
* Copyright (C) 1998-2000 Andre Hedrick <andre@linux-ide.org>
*
* May be copied or modified under the terms of the GNU General Public
* License
*/
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/pci.h>
#include <linux/init.h>
#include <linux/blkdev.h>
#include <linux/delay.h>
#include <scsi/scsi_host.h>
#include <linux/libata.h>
#define DRV_NAME "pata_hpt3x3"
#define DRV_VERSION "0.5.3"
/**
* hpt3x3_set_piomode - PIO setup
* @ap: ATA interface
* @adev: device on the interface
*
* Set our PIO requirements. This is fairly simple on the HPT3x3 as
* all we have to do is clear the MWDMA and UDMA bits then load the
* mode number.
*/
static void hpt3x3_set_piomode(struct ata_port *ap, struct ata_device *adev)
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
u32 r1, r2;
int dn = 2 * ap->port_no + adev->devno;
pci_read_config_dword(pdev, 0x44, &r1);
pci_read_config_dword(pdev, 0x48, &r2);
/* Load the PIO timing number */
r1 &= ~(7 << (3 * dn));
r1 |= (adev->pio_mode - XFER_PIO_0) << (3 * dn);
r2 &= ~(0x11 << dn); /* Clear MWDMA and UDMA bits */
pci_write_config_dword(pdev, 0x44, r1);
pci_write_config_dword(pdev, 0x48, r2);
}
/**
* hpt3x3_set_dmamode - DMA timing setup
* @ap: ATA interface
* @adev: Device being configured
*
* Set up the channel for MWDMA or UDMA modes. Much the same as with
* PIO, load the mode number and then set MWDMA or UDMA flag.
*
* 0x44 : bit 0-2 master mode, 3-5 slave mode, etc
* 0x48 : bit 4/0 DMA/UDMA bit 5/1 for slave etc
*/
static void hpt3x3_set_dmamode(struct ata_port *ap, struct ata_device *adev)
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
u32 r1, r2;
int dn = 2 * ap->port_no + adev->devno;
int mode_num = adev->dma_mode & 0x0F;
pci_read_config_dword(pdev, 0x44, &r1);
pci_read_config_dword(pdev, 0x48, &r2);
/* Load the timing number */
r1 &= ~(7 << (3 * dn));
r1 |= (mode_num << (3 * dn));
r2 &= ~(0x11 << dn); /* Clear MWDMA and UDMA bits */
if (adev->dma_mode >= XFER_UDMA_0)
r2 |= (0x10 << dn); /* Ultra mode */
else
r2 |= (0x01 << dn); /* MWDMA */
pci_write_config_dword(pdev, 0x44, r1);
pci_write_config_dword(pdev, 0x48, r2);
}
/**
* hpt3x3_atapi_dma - ATAPI DMA check
* @qc: Queued command
*
* Just say no - we don't do ATAPI DMA
*/
static int hpt3x3_atapi_dma(struct ata_queued_cmd *qc)
{
return 1;
}
static struct scsi_host_template hpt3x3_sht = {
.module = THIS_MODULE,
.name = DRV_NAME,
.ioctl = ata_scsi_ioctl,
.queuecommand = ata_scsi_queuecmd,
.can_queue = ATA_DEF_QUEUE,
.this_id = ATA_SHT_THIS_ID,
.sg_tablesize = LIBATA_MAX_PRD,
.cmd_per_lun = ATA_SHT_CMD_PER_LUN,
.emulated = ATA_SHT_EMULATED,
.use_clustering = ATA_SHT_USE_CLUSTERING,
.proc_name = DRV_NAME,
.dma_boundary = ATA_DMA_BOUNDARY,
.slave_configure = ata_scsi_slave_config,
.slave_destroy = ata_scsi_slave_destroy,
.bios_param = ata_std_bios_param,
};
static struct ata_port_operations hpt3x3_port_ops = {
.port_disable = ata_port_disable,
.set_piomode = hpt3x3_set_piomode,
.mode_filter = ata_pci_default_filter,
.tf_load = ata_tf_load,
.tf_read = ata_tf_read,
.check_status = ata_check_status,
.exec_command = ata_exec_command,
.dev_select = ata_std_dev_select,
.freeze = ata_bmdma_freeze,
.thaw = ata_bmdma_thaw,
.error_handler = ata_bmdma_error_handler,
.post_internal_cmd = ata_bmdma_post_internal_cmd,
.cable_detect = ata_cable_40wire,
.bmdma_setup = ata_bmdma_setup,
.bmdma_start = ata_bmdma_start,
.bmdma_stop = ata_bmdma_stop,
.bmdma_status = ata_bmdma_status,
.check_atapi_dma= hpt3x3_atapi_dma,
.qc_prep = ata_qc_prep,
.qc_issue = ata_qc_issue_prot,
.data_xfer = ata_data_xfer,
.irq_handler = ata_interrupt,
.irq_clear = ata_bmdma_irq_clear,
.irq_on = ata_irq_on,
.irq_ack = ata_irq_ack,
.port_start = ata_port_start,
};
/**
* hpt3x3_init_chipset - chip setup
* @dev: PCI device
*
* Perform the setup required at boot and on resume.
*/
static void hpt3x3_init_chipset(struct pci_dev *dev)
{
u16 cmd;
/* Initialize the board */
pci_write_config_word(dev, 0x80, 0x00);
/* Check if it is a 343 or a 363. 363 has COMMAND_MEMORY set */
pci_read_config_word(dev, PCI_COMMAND, &cmd);
if (cmd & PCI_COMMAND_MEMORY)
pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0xF0);
else
pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0x20);
}
/**
* hpt3x3_init_one - Initialise an HPT343/363
* @pdev: PCI device
* @id: Entry in match table
*
* Perform basic initialisation. We set the device up so we access all
* ports via BAR4. This is neccessary to work around errata.
*/
static int hpt3x3_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
{
static int printed_version;
static const struct ata_port_info info = {
.sht = &hpt3x3_sht,
.flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f,
#if defined(CONFIG_PATA_HPT3X3_DMA)
/* Further debug needed */
.mwdma_mask = 0x07,
.udma_mask = 0x07,
#endif
.port_ops = &hpt3x3_port_ops
};
/* Register offsets of taskfiles in BAR4 area */
static const u8 offset_cmd[2] = { 0x20, 0x28 };
static const u8 offset_ctl[2] = { 0x36, 0x3E };
const struct ata_port_info *ppi[] = { &info, NULL };
struct ata_host *host;
int i, rc;
void __iomem *base;
hpt3x3_init_chipset(pdev);
if (!printed_version++)
dev_printk(KERN_DEBUG, &pdev->dev, "version " DRV_VERSION "\n");
host = ata_host_alloc_pinfo(&pdev->dev, ppi, 2);
if (!host)
return -ENOMEM;
/* acquire resources and fill host */
rc = pcim_enable_device(pdev);
if (rc)
return rc;
/* Everything is relative to BAR4 if we set up this way */
rc = pcim_iomap_regions(pdev, 1 << 4, DRV_NAME);
if (rc == -EBUSY)
pcim_pin_device(pdev);
if (rc)
return rc;
host->iomap = pcim_iomap_table(pdev);
rc = pci_set_dma_mask(pdev, ATA_DMA_MASK);
if (rc)
return rc;
rc = pci_set_consistent_dma_mask(pdev, ATA_DMA_MASK);
if (rc)
return rc;
base = host->iomap[4]; /* Bus mastering base */
for (i = 0; i < host->n_ports; i++) {
struct ata_ioports *ioaddr = &host->ports[i]->ioaddr;
ioaddr->cmd_addr = base + offset_cmd[i];
ioaddr->altstatus_addr =
ioaddr->ctl_addr = base + offset_ctl[i];
ioaddr->scr_addr = NULL;
ata_std_ports(ioaddr);
ioaddr->bmdma_addr = base + 8 * i;
}
pci_set_master(pdev);
return ata_host_activate(host, pdev->irq, ata_interrupt, IRQF_SHARED,
&hpt3x3_sht);
}
#ifdef CONFIG_PM
static int hpt3x3_reinit_one(struct pci_dev *dev)
{
hpt3x3_init_chipset(dev);
return ata_pci_device_resume(dev);
}
#endif
static const struct pci_device_id hpt3x3[] = {
{ PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT343), },
{ },
};
static struct pci_driver hpt3x3_pci_driver = {
.name = DRV_NAME,
.id_table = hpt3x3,
.probe = hpt3x3_init_one,
.remove = ata_pci_remove_one,
#ifdef CONFIG_PM
.suspend = ata_pci_device_suspend,
.resume = hpt3x3_reinit_one,
#endif
};
static int __init hpt3x3_init(void)
{
return pci_register_driver(&hpt3x3_pci_driver);
}
static void __exit hpt3x3_exit(void)
{
pci_unregister_driver(&hpt3x3_pci_driver);
}
MODULE_AUTHOR("Alan Cox");
MODULE_DESCRIPTION("low-level driver for the Highpoint HPT343/363");
MODULE_LICENSE("GPL");
MODULE_DEVICE_TABLE(pci, hpt3x3);
MODULE_VERSION(DRV_VERSION);
module_init(hpt3x3_init);
module_exit(hpt3x3_exit);