| /* |
| * phyCORE-MPC5200B-tiny (pcm030) board Device Tree Source |
| * |
| * Copyright 2006 Pengutronix |
| * Sascha Hauer <s.hauer@pengutronix.de> |
| * Copyright 2007 Pengutronix |
| * Juergen Beisert <j.beisert@pengutronix.de> |
| * |
| * This program is free software; you can redistribute it and/or modify it |
| * under the terms of the GNU General Public License as published by the |
| * Free Software Foundation; either version 2 of the License, or (at your |
| * option) any later version. |
| */ |
| |
| /dts-v1/; |
| |
| / { |
| model = "phytec,pcm030"; |
| compatible = "phytec,pcm030"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| |
| cpus { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| PowerPC,5200@0 { |
| device_type = "cpu"; |
| reg = <0>; |
| d-cache-line-size = <32>; |
| i-cache-line-size = <32>; |
| d-cache-size = <0x4000>; /* L1, 16K */ |
| i-cache-size = <0x4000>; /* L1, 16K */ |
| timebase-frequency = <0>; /* From Bootloader */ |
| bus-frequency = <0>; /* From Bootloader */ |
| clock-frequency = <0>; /* From Bootloader */ |
| }; |
| }; |
| |
| memory { |
| device_type = "memory"; |
| reg = <0x00000000 0x04000000>; /* 64MB */ |
| }; |
| |
| soc5200@f0000000 { |
| #address-cells = <1>; |
| #size-cells = <1>; |
| compatible = "fsl,mpc5200b-immr"; |
| ranges = <0x0 0xf0000000 0x0000c000>; |
| bus-frequency = <0>; /* From bootloader */ |
| system-frequency = <0>; /* From bootloader */ |
| |
| cdm@200 { |
| compatible = "fsl,mpc5200b-cdm","fsl,mpc5200-cdm"; |
| reg = <0x200 0x38>; |
| }; |
| |
| mpc5200_pic: interrupt-controller@500 { |
| /* 5200 interrupts are encoded into two levels; */ |
| interrupt-controller; |
| #interrupt-cells = <3>; |
| device_type = "interrupt-controller"; |
| compatible = "fsl,mpc5200b-pic","fsl,mpc5200-pic"; |
| reg = <0x500 0x80>; |
| }; |
| |
| timer@600 { /* General Purpose Timer */ |
| compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt"; |
| cell-index = <0>; |
| reg = <0x600 0x10>; |
| interrupts = <0x1 0x9 0x0>; |
| interrupt-parent = <&mpc5200_pic>; |
| fsl,has-wdt; |
| }; |
| |
| timer@610 { /* General Purpose Timer */ |
| compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt"; |
| cell-index = <1>; |
| reg = <0x610 0x10>; |
| interrupts = <0x1 0xa 0x0>; |
| interrupt-parent = <&mpc5200_pic>; |
| }; |
| |
| gpt2: timer@620 { /* General Purpose Timer in GPIO mode */ |
| compatible = "fsl,mpc5200b-gpt-gpio","fsl,mpc5200-gpt-gpio"; |
| cell-index = <2>; |
| reg = <0x620 0x10>; |
| interrupts = <0x1 0xb 0x0>; |
| interrupt-parent = <&mpc5200_pic>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| }; |
| |
| gpt3: timer@630 { /* General Purpose Timer in GPIO mode */ |
| compatible = "fsl,mpc5200b-gpt-gpio","fsl,mpc5200-gpt-gpio"; |
| cell-index = <3>; |
| reg = <0x630 0x10>; |
| interrupts = <0x1 0xc 0x0>; |
| interrupt-parent = <&mpc5200_pic>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| }; |
| |
| gpt4: timer@640 { /* General Purpose Timer in GPIO mode */ |
| compatible = "fsl,mpc5200b-gpt-gpio","fsl,mpc5200-gpt-gpio"; |
| cell-index = <4>; |
| reg = <0x640 0x10>; |
| interrupts = <0x1 0xd 0x0>; |
| interrupt-parent = <&mpc5200_pic>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| }; |
| |
| gpt5: timer@650 { /* General Purpose Timer in GPIO mode */ |
| compatible = "fsl,mpc5200b-gpt-gpio","fsl,mpc5200-gpt-gpio"; |
| cell-index = <5>; |
| reg = <0x650 0x10>; |
| interrupts = <0x1 0xe 0x0>; |
| interrupt-parent = <&mpc5200_pic>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| }; |
| |
| gpt6: timer@660 { /* General Purpose Timer in GPIO mode */ |
| compatible = "fsl,mpc5200b-gpt-gpio","fsl,mpc5200-gpt-gpio"; |
| cell-index = <6>; |
| reg = <0x660 0x10>; |
| interrupts = <0x1 0xf 0x0>; |
| interrupt-parent = <&mpc5200_pic>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| }; |
| |
| gpt7: timer@670 { /* General Purpose Timer in GPIO mode */ |
| compatible = "fsl,mpc5200b-gpt-gpio","fsl,mpc5200-gpt-gpio"; |
| cell-index = <7>; |
| reg = <0x670 0x10>; |
| interrupts = <0x1 0x10 0x0>; |
| interrupt-parent = <&mpc5200_pic>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| }; |
| |
| rtc@800 { // Real time clock |
| compatible = "fsl,mpc5200b-rtc","fsl,mpc5200-rtc"; |
| reg = <0x800 0x100>; |
| interrupts = <0x1 0x5 0x0 0x1 0x6 0x0>; |
| interrupt-parent = <&mpc5200_pic>; |
| }; |
| |
| can@900 { |
| compatible = "fsl,mpc5200b-mscan","fsl,mpc5200-mscan"; |
| cell-index = <0>; |
| interrupts = <0x2 0x11 0x0>; |
| interrupt-parent = <&mpc5200_pic>; |
| reg = <0x900 0x80>; |
| }; |
| |
| can@980 { |
| compatible = "fsl,mpc5200b-mscan","fsl,mpc5200-mscan"; |
| cell-index = <1>; |
| interrupts = <0x2 0x12 0x0>; |
| interrupt-parent = <&mpc5200_pic>; |
| reg = <0x980 0x80>; |
| }; |
| |
| gpio_simple: gpio@b00 { |
| compatible = "fsl,mpc5200b-gpio","fsl,mpc5200-gpio"; |
| reg = <0xb00 0x40>; |
| interrupts = <0x1 0x7 0x0>; |
| interrupt-parent = <&mpc5200_pic>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| }; |
| |
| gpio_wkup: gpio-wkup@c00 { |
| compatible = "fsl,mpc5200b-gpio-wkup","fsl,mpc5200-gpio-wkup"; |
| reg = <0xc00 0x40>; |
| interrupts = <0x1 0x8 0x0 0x0 0x3 0x0>; |
| interrupt-parent = <&mpc5200_pic>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| }; |
| |
| spi@f00 { |
| compatible = "fsl,mpc5200b-spi","fsl,mpc5200-spi"; |
| reg = <0xf00 0x20>; |
| interrupts = <0x2 0xd 0x0 0x2 0xe 0x0>; |
| interrupt-parent = <&mpc5200_pic>; |
| }; |
| |
| usb@1000 { |
| compatible = "fsl,mpc5200b-ohci","fsl,mpc5200-ohci","ohci-be"; |
| reg = <0x1000 0xff>; |
| interrupts = <0x2 0x6 0x0>; |
| interrupt-parent = <&mpc5200_pic>; |
| }; |
| |
| dma-controller@1200 { |
| device_type = "dma-controller"; |
| compatible = "fsl,mpc5200b-bestcomm","fsl,mpc5200-bestcomm"; |
| reg = <0x1200 0x80>; |
| interrupts = <0x3 0x0 0x0 0x3 0x1 0x0 0x3 0x2 0x0 0x3 0x3 0x0 |
| 0x3 0x4 0x0 0x3 0x5 0x0 0x3 0x6 0x0 0x3 0x7 0x0 |
| 0x3 0x8 0x0 0x3 0x9 0x0 0x3 0xa 0x0 0x3 0xb 0x0 |
| 0x3 0xc 0x0 0x3 0xd 0x0 0x3 0xe 0x0 0x3 0xf 0x0>; |
| interrupt-parent = <&mpc5200_pic>; |
| }; |
| |
| xlb@1f00 { |
| compatible = "fsl,mpc5200b-xlb","fsl,mpc5200-xlb"; |
| reg = <0x1f00 0x100>; |
| }; |
| |
| ac97@2000 { /* PSC1 in ac97 mode */ |
| device_type = "sound"; |
| compatible = "mpc5200b-psc-ac97","fsl,mpc5200b-psc-ac97"; |
| cell-index = <0>; |
| reg = <0x2000 0x100>; |
| interrupts = <0x2 0x2 0x0>; |
| interrupt-parent = <&mpc5200_pic>; |
| }; |
| |
| /* PSC2 port is used by CAN1/2 */ |
| |
| serial@2400 { /* PSC3 in UART mode */ |
| device_type = "serial"; |
| compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart"; |
| port-number = <0>; |
| cell-index = <2>; |
| reg = <0x2400 0x100>; |
| interrupts = <0x2 0x3 0x0>; |
| interrupt-parent = <&mpc5200_pic>; |
| }; |
| |
| /* PSC4 is ??? */ |
| |
| /* PSC5 is ??? */ |
| |
| serial@2c00 { /* PSC6 in UART mode */ |
| device_type = "serial"; |
| compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart"; |
| port-number = <1>; |
| cell-index = <5>; |
| reg = <0x2c00 0x100>; |
| interrupts = <0x2 0x4 0x0>; |
| interrupt-parent = <&mpc5200_pic>; |
| }; |
| |
| ethernet@3000 { |
| device_type = "network"; |
| compatible = "fsl,mpc5200b-fec","fsl,mpc5200-fec"; |
| reg = <0x3000 0x400>; |
| local-mac-address = [00 00 00 00 00 00]; |
| interrupts = <0x2 0x5 0x0>; |
| interrupt-parent = <&mpc5200_pic>; |
| phy-handle = <&phy0>; |
| }; |
| |
| mdio@3000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "fsl,mpc5200b-mdio", "fsl,mpc5200-mdio"; |
| reg = <0x3000 0x400>; /* fec range, since we need to setup fec interrupts */ |
| interrupts = <0x2 0x5 0x0>; /* these are for "mii command finished", not link changes & co. */ |
| interrupt-parent = <&mpc5200_pic>; |
| |
| phy0:ethernet-phy@0 { |
| device_type = "ethernet-phy"; |
| reg = <0x0>; |
| }; |
| }; |
| |
| ata@3a00 { |
| device_type = "ata"; |
| compatible = "fsl,mpc5200b-ata","fsl,mpc5200-ata"; |
| reg = <0x3a00 0x100>; |
| interrupts = <0x2 0x7 0x0>; |
| interrupt-parent = <&mpc5200_pic>; |
| }; |
| |
| i2c@3d00 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "fsl,mpc5200b-i2c","fsl,mpc5200-i2c","fsl-i2c"; |
| cell-index = <0>; |
| reg = <0x3d00 0x40>; |
| interrupts = <0x2 0xf 0x0>; |
| interrupt-parent = <&mpc5200_pic>; |
| fsl5200-clocking; |
| }; |
| |
| i2c@3d40 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "fsl,mpc5200b-i2c","fsl,mpc5200-i2c","fsl-i2c"; |
| cell-index = <1>; |
| reg = <0x3d40 0x40>; |
| interrupts = <0x2 0x10 0x0>; |
| interrupt-parent = <&mpc5200_pic>; |
| fsl5200-clocking; |
| rtc@51 { |
| compatible = "nxp,pcf8563"; |
| reg = <0x51>; |
| }; |
| /* FIXME: EEPROM */ |
| }; |
| |
| sram@8000 { |
| compatible = "fsl,mpc5200b-sram","fsl,mpc5200-sram","sram"; |
| reg = <0x8000 0x4000>; |
| }; |
| |
| /* This is only an example device to show the usage of gpios. It maps all available |
| * gpios to the "gpio-provider" device. |
| */ |
| gpio { |
| compatible = "gpio-provider"; |
| |
| /* mpc52xx exp.con patchfield */ |
| gpios = <&gpio_wkup 0 0 /* GPIO_WKUP_7 11d jp13-3 */ |
| &gpio_wkup 1 0 /* GPIO_WKUP_6 14c */ |
| &gpio_wkup 6 0 /* PSC2_4 43c x5-11 */ |
| &gpio_simple 2 0 /* IRDA_1 24c x7-6 set GPS_PORT_CONFIG[IRDA] = 0 */ |
| &gpio_simple 3 0 /* IRDA_0 x8-5 set GPS_PORT_CONFIG[IRDA] = 0 */ |
| &gpt2 0 0 /* timer2 12d x4-4 */ |
| &gpt3 0 0 /* timer3 13d x6-4 */ |
| &gpt4 0 0 /* timer4 61c x2-16 */ |
| &gpt5 0 0 /* timer5 44c x7-11 */ |
| &gpt6 0 0 /* timer6 60c x8-15 */ |
| &gpt7 0 0 /* timer7 36a x17-9 */ |
| >; |
| }; |
| }; |
| |
| pci@f0000d00 { |
| #interrupt-cells = <1>; |
| #size-cells = <2>; |
| #address-cells = <3>; |
| device_type = "pci"; |
| compatible = "fsl,mpc5200b-pci","fsl,mpc5200-pci"; |
| reg = <0xf0000d00 0x100>; |
| interrupt-map-mask = <0xf800 0x0 0x0 0x7>; |
| interrupt-map = <0xc000 0x0 0x0 0x1 &mpc5200_pic 0x0 0x0 0x3 /* 1st slot */ |
| 0xc000 0x0 0x0 0x2 &mpc5200_pic 0x1 0x1 0x3 |
| 0xc000 0x0 0x0 0x3 &mpc5200_pic 0x1 0x2 0x3 |
| 0xc000 0x0 0x0 0x4 &mpc5200_pic 0x1 0x3 0x3 |
| |
| 0xc800 0x0 0x0 0x1 &mpc5200_pic 0x1 0x1 0x3 /* 2nd slot */ |
| 0xc800 0x0 0x0 0x2 &mpc5200_pic 0x1 0x2 0x3 |
| 0xc800 0x0 0x0 0x3 &mpc5200_pic 0x1 0x3 0x3 |
| 0xc800 0x0 0x0 0x4 &mpc5200_pic 0x0 0x0 0x3>; |
| clock-frequency = <0>; // From boot loader |
| interrupts = <0x2 0x8 0x0 0x2 0x9 0x0 0x2 0xa 0x0>; |
| interrupt-parent = <&mpc5200_pic>; |
| bus-range = <0 0>; |
| ranges = <0x42000000 0x0 0x80000000 0x80000000 0x0 0x20000000 |
| 0x02000000 0x0 0xa0000000 0xa0000000 0x0 0x10000000 |
| 0x01000000 0x0 0x00000000 0xb0000000 0x0 0x01000000>; |
| }; |
| }; |