| |
| /* |
| * Copyright (c) 2012, The Linux Foundation. All rights reserved. |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License version 2 and |
| * only version 2 as published by the Free Software Foundation. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| */ |
| |
| &cci { |
| |
| qcom,camera@6e { |
| compatible = "qcom,s5k3l1yx"; |
| reg = <0x6e 0x0>; |
| qcom,csi-if = <1>; |
| qcom,csid-core = <0>; |
| qcom,flash-type = <0>; |
| qcom,mount-angle = <0>; |
| qcom,sensor-name = "s5k3l1yx"; |
| cam_vdig-supply = <&pm8941_l3>; |
| cam_vana-supply = <&pm8941_l17>; |
| cam_vio-supply = <&pm8941_lvs3>; |
| cam_vaf-supply = <&pm8941_l23>; |
| qcom,cam-vreg-name = "cam_vdig", "cam_vana", "cam_vio", |
| "cam_vaf"; |
| qcom,cam-vreg-type = <0 0 1 0>; |
| qcom,cam-vreg-min-voltage = <1225000 2850000 0 3000000>; |
| qcom,cam-vreg-max-voltage = <1225000 2850000 0 3000000>; |
| qcom,cam-vreg-op-mode = <105000 80000 0 100000>; |
| qcom,gpio-no-mux = <0>; |
| gpios = <&msmgpio 15 0>, |
| <&msmgpio 19 0>, |
| <&msmgpio 20 0>, |
| <&msmgpio 90 0>; |
| qcom,gpio-common-tbl-num = <0 1 2>; |
| qcom,gpio-common-tbl-flags = <1 1 1>; |
| qcom,gpio-common-tbl-label = "CAMIF_MCLK", |
| "CAMIF_I2C_DATA", |
| "CAMIF_I2C_CLK"; |
| qcom,gpio-req-tbl-num = <3>; |
| qcom,gpio-req-tbl-flags = <0>; |
| qcom,gpio-req-tbl-label = "CAM_RESET1"; |
| qcom,gpio-set-tbl-num = <3 3>; |
| qcom,gpio-set-tbl-flags = <0 2>; |
| qcom,gpio-set-tbl-delay = <1000 30000>; |
| qcom,csi-lane-assign = <0x4320>; |
| qcom,csi-lane-mask = <0x1F>; |
| qcom,csi-phy-sel = <0>; |
| qcom,camera-type = <0>; |
| qcom,sensor-type = <0>; |
| status = "ok"; |
| }; |
| |
| qcom,camera@6c { |
| compatible = "qcom,ov2720"; |
| reg = <0x6c 0x0>; |
| qcom,csi-if = <1>; |
| qcom,csid-core = <0>; |
| qcom,flash-type = <0>; |
| qcom,mount-angle = <180>; |
| qcom,sensor-name = "ov2720"; |
| cam_vdig-supply = <&pm8941_l3>; |
| cam_vana-supply = <&pm8941_l17>; |
| cam_vio-supply = <&pm8941_lvs2>; |
| qcom,cam-vreg-name = "cam_vdig", "cam_vana", "cam_vio"; |
| qcom,cam-vreg-type = <0 0 1>; |
| qcom,cam-vreg-min-voltage = <1225000 2850000 0>; |
| qcom,cam-vreg-max-voltage = <1225000 2850000 0>; |
| qcom,cam-vreg-op-mode = <105000 80000 0>; |
| qcom,gpio-no-mux = <0>; |
| gpios = <&msmgpio 17 0>, |
| <&msmgpio 19 0>, |
| <&msmgpio 20 0>, |
| <&msmgpio 18 0>; |
| qcom,gpio-common-tbl-num = <0 1 2>; |
| qcom,gpio-common-tbl-flags = <1 1 1>; |
| qcom,gpio-common-tbl-label = "CAMIF_MCLK", |
| "CAMIF_I2C_DATA", |
| "CAMIF_I2C_CLK"; |
| qcom,gpio-req-tbl-num = <3>; |
| qcom,gpio-req-tbl-flags = <0>; |
| qcom,gpio-req-tbl-label = "CAM_RESET1"; |
| qcom,gpio-set-tbl-num = <3 3>; |
| qcom,gpio-set-tbl-flags = <0 2>; |
| qcom,gpio-set-tbl-delay = <1000 4000>; |
| qcom,csi-lane-assign = <0x4320>; |
| qcom,csi-lane-mask = <0x7>; |
| qcom,csi-phy-sel = <2>; |
| qcom,camera-type = <1>; |
| qcom,sensor-type = <0>; |
| status = "ok"; |
| }; |
| }; |