drivers/usb/dwc3/dwc3_otg.c

/**
 * dwc3_otg.c - DesignWare USB3 DRD Controller OTG
 *
 * Copyright (c) 2012-2013, The Linux Foundation. All rights reserved.
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License version 2 and
 * only version 2 as published by the Free Software Foundation.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 */

#include <linux/usb.h>
#include <linux/usb/hcd.h>
#include <linux/platform_device.h>
#include <linux/regulator/consumer.h>

#include "core.h"
#include "dwc3_otg.h"
#include "io.h"
#include "xhci.h"

static void dwc3_otg_reset(struct dwc3_otg *dotg);

static void dwc3_otg_notify_host_mode(struct usb_otg *otg, int host_mode);
static void dwc3_otg_reset(struct dwc3_otg *dotg);

/**
 * dwc3_otg_set_host_regs - reset dwc3 otg registers to host operation.
 *
 * This function sets the OTG registers to work in A-Device host mode.
 * This function should be called just before entering to A-Device mode.
 *
 * @w: Pointer to the dwc3 otg struct
 */
static void dwc3_otg_set_host_regs(struct dwc3_otg *dotg)
{
	u32 reg;
	struct dwc3 *dwc = dotg->dwc;
	struct dwc3_ext_xceiv *ext_xceiv = dotg->ext_xceiv;

	if (ext_xceiv && !ext_xceiv->otg_capability) {
		/* Set OCTL[6](PeriMode) to 0 (host) */
		reg = dwc3_readl(dotg->regs, DWC3_OCTL);
		reg &= ~DWC3_OTG_OCTL_PERIMODE;
		dwc3_writel(dotg->regs, DWC3_OCTL, reg);
	} else {
		reg = dwc3_readl(dwc->regs, DWC3_GCTL);
		reg &= ~(DWC3_GCTL_PRTCAPDIR(DWC3_GCTL_PRTCAP_OTG));
		reg |= DWC3_GCTL_PRTCAPDIR(DWC3_GCTL_PRTCAP_HOST);
		dwc3_writel(dwc->regs, DWC3_GCTL, reg);
	}
}

static int dwc3_otg_set_suspend(struct usb_phy *phy, int suspend)
{
	struct usb_otg *otg = phy->otg;
	struct dwc3_otg *dotg = container_of(otg, struct dwc3_otg, otg);

	if (dotg->host_bus_suspend == suspend)
		return 0;

	dotg->host_bus_suspend = suspend;
	if (suspend) {
		pm_runtime_put_sync(phy->dev);
	} else {
		pm_runtime_get_noresume(phy->dev);
		pm_runtime_resume(phy->dev);
	}

	return 0;
}

/**
 * dwc3_otg_set_host_power - Enable port power control for host operation
 *
 * This function enables the OTG Port Power required to operate in Host mode
 * This function should be called only after XHCI driver has set the port
 * power in PORTSC register.
 *
 * @w: Pointer to the dwc3 otg struct
 */
void dwc3_otg_set_host_power(struct dwc3_otg *dotg)
{
	u32 osts;

	osts = dwc3_readl(dotg->regs, DWC3_OSTS);
	if (!(osts & 0x8))
		dev_err(dotg->dwc->dev, "%s: xHCIPrtPower not set\n", __func__);

	dwc3_writel(dotg->regs, DWC3_OCTL, DWC3_OTG_OCTL_PRTPWRCTL);
}

/**
 * dwc3_otg_set_peripheral_regs - reset dwc3 otg registers to peripheral operation.
 *
 * This function sets the OTG registers to work in B-Device peripheral mode.
 * This function should be called just before entering to B-Device mode.
 *
 * @w: Pointer to the dwc3 otg workqueue.
 */
static void dwc3_otg_set_peripheral_regs(struct dwc3_otg *dotg)
{
	u32 reg;
	struct dwc3 *dwc = dotg->dwc;
	struct dwc3_ext_xceiv *ext_xceiv = dotg->ext_xceiv;

	if (ext_xceiv && !ext_xceiv->otg_capability) {
		/* Set OCTL[6](PeriMode) to 1 (peripheral) */
		reg = dwc3_readl(dotg->regs, DWC3_OCTL);
		reg |= DWC3_OTG_OCTL_PERIMODE;
		dwc3_writel(dotg->regs, DWC3_OCTL, reg);
		/*
		 * TODO: add more OTG registers writes for PERIPHERAL mode here,
		 * see figure 12-19 B-device flow in dwc3 Synopsis spec
		 */
	} else {
		reg = dwc3_readl(dwc->regs, DWC3_GCTL);
		reg &= ~(DWC3_GCTL_PRTCAPDIR(DWC3_GCTL_PRTCAP_OTG));
		reg |= DWC3_GCTL_PRTCAPDIR(DWC3_GCTL_PRTCAP_DEVICE);
		dwc3_writel(dwc->regs, DWC3_GCTL, reg);
	}
}

/**
 * dwc3_otg_start_host -  helper function for starting/stoping the host controller driver.
 *
 * @otg: Pointer to the otg_transceiver structure.
 * @on: start / stop the host controller driver.
 *
 * Returns 0 on success otherwise negative errno.
 */
static int dwc3_otg_start_host(struct usb_otg *otg, int on)
{
	struct dwc3_otg *dotg = container_of(otg, struct dwc3_otg, otg);
	struct dwc3_ext_xceiv *ext_xceiv = dotg->ext_xceiv;
	struct dwc3 *dwc = dotg->dwc;
	int ret = 0;

	if (!dwc->xhci)
		return -EINVAL;

	if (!dotg->vbus_otg) {
		dotg->vbus_otg = devm_regulator_get(dwc->dev->parent,
							"vbus_dwc3");
		if (IS_ERR(dotg->vbus_otg)) {
			dev_err(dwc->dev, "Failed to get vbus regulator\n");
			ret = PTR_ERR(dotg->vbus_otg);
			dotg->vbus_otg = 0;
			return ret;
		}
	}

	if (on) {
		dev_dbg(otg->phy->dev, "%s: turn on host\n", __func__);

		/*
		 * This should be revisited for more testing post-silicon.
		 * In worst case we may need to disconnect the root hub
		 * before stopping the controller so that it does not
		 * interfere with runtime pm/system pm.
		 * We can also consider registering and unregistering xhci
		 * platform device. It is almost similar to add_hcd and
		 * remove_hcd, But we may not use standard set_host method
		 * anymore.
		 */
		dwc3_otg_set_host_regs(dotg);
		/*
		 * FIXME If micro A cable is disconnected during system suspend,
		 * xhci platform device will be removed before runtime pm is
		 * enabled for xhci device. Due to this, disable_depth becomes
		 * greater than one and runtimepm is not enabled for next microA
		 * connect. Fix this by calling pm_runtime_init for xhci device.
		 */
		pm_runtime_init(&dwc->xhci->dev);
		ret = platform_device_add(dwc->xhci);
		if (ret) {
			dev_err(otg->phy->dev,
				"%s: failed to add XHCI pdev ret=%d\n",
				__func__, ret);
			return ret;
		}

		dwc3_otg_notify_host_mode(otg, on);
		ret = regulator_enable(dotg->vbus_otg);
		if (ret) {
			dev_err(otg->phy->dev, "unable to enable vbus_otg\n");
			platform_device_del(dwc->xhci);
			return ret;
		}

		/* re-init OTG EVTEN register as XHCI reset clears it */
		if (ext_xceiv && !ext_xceiv->otg_capability)
			dwc3_otg_reset(dotg);
	} else {
		dev_dbg(otg->phy->dev, "%s: turn off host\n", __func__);

		ret = regulator_disable(dotg->vbus_otg);
		if (ret) {
			dev_err(otg->phy->dev, "unable to disable vbus_otg\n");
			return ret;
		}
		dwc3_otg_notify_host_mode(otg, on);

		platform_device_del(dwc->xhci);
		/*
		 * Perform USB hardware RESET (both core reset and DBM reset)
		 * when moving from host to peripheral. This is required for
		 * peripheral mode to work.
		 */
		if (ext_xceiv && ext_xceiv->otg_capability &&
						ext_xceiv->ext_block_reset)
			ext_xceiv->ext_block_reset(true);

		dwc3_otg_set_peripheral_regs(dotg);

		/* re-init core and OTG registers as block reset clears these */
		dwc3_post_host_reset_core_init(dwc);
		if (ext_xceiv && !ext_xceiv->otg_capability)
			dwc3_otg_reset(dotg);
	}

	return 0;
}

/**
 * dwc3_otg_set_host -  bind/unbind the host controller driver.
 *
 * @otg: Pointer to the otg_transceiver structure.
 * @host: Pointer to the usb_bus structure.
 *
 * Returns 0 on success otherwise negative errno.
 */
static int dwc3_otg_set_host(struct usb_otg *otg, struct usb_bus *host)
{
	struct dwc3_otg *dotg = container_of(otg, struct dwc3_otg, otg);

	if (host) {
		dev_dbg(otg->phy->dev, "%s: set host %s, portpower\n",
					__func__, host->bus_name);
		otg->host = host;
		/*
		 * Though XHCI power would be set by now, but some delay is
		 * required for XHCI controller before setting OTG Port Power
		 * TODO: Tune this delay
		 */
		msleep(300);
		dwc3_otg_set_host_power(dotg);
	} else {
		otg->host = NULL;
	}

	return 0;
}

/**
 * dwc3_otg_start_peripheral -  bind/unbind the peripheral controller.
 *
 * @otg: Pointer to the otg_transceiver structure.
 * @gadget: pointer to the usb_gadget structure.
 *
 * Returns 0 on success otherwise negative errno.
 */
static int dwc3_otg_start_peripheral(struct usb_otg *otg, int on)
{
	struct dwc3_otg *dotg = container_of(otg, struct dwc3_otg, otg);
	struct dwc3_ext_xceiv *ext_xceiv = dotg->ext_xceiv;

	if (!otg->gadget)
		return -EINVAL;

	if (on) {
		dev_dbg(otg->phy->dev, "%s: turn on gadget %s\n",
					__func__, otg->gadget->name);

		/* Core reset is not required during start peripheral. Only
		 * DBM reset is required, hence perform only DBM reset here */
		if (ext_xceiv && ext_xceiv->otg_capability &&
						ext_xceiv->ext_block_reset)
			ext_xceiv->ext_block_reset(false);

		dwc3_otg_set_peripheral_regs(dotg);
		usb_gadget_vbus_connect(otg->gadget);
	} else {
		dev_dbg(otg->phy->dev, "%s: turn off gadget %s\n",
					__func__, otg->gadget->name);
		usb_gadget_vbus_disconnect(otg->gadget);
	}

	return 0;
}

/**
 * dwc3_otg_set_peripheral -  bind/unbind the peripheral controller driver.
 *
 * @otg: Pointer to the otg_transceiver structure.
 * @gadget: pointer to the usb_gadget structure.
 *
 * Returns 0 on success otherwise negative errno.
 */
static int dwc3_otg_set_peripheral(struct usb_otg *otg,
				struct usb_gadget *gadget)
{
	struct dwc3_otg *dotg = container_of(otg, struct dwc3_otg, otg);

	if (gadget) {
		dev_dbg(otg->phy->dev, "%s: set gadget %s\n",
					__func__, gadget->name);
		otg->gadget = gadget;
		schedule_work(&dotg->sm_work);
	} else {
		if (otg->phy->state == OTG_STATE_B_PERIPHERAL) {
			dwc3_otg_start_peripheral(otg, 0);
			otg->gadget = NULL;
			otg->phy->state = OTG_STATE_UNDEFINED;
			schedule_work(&dotg->sm_work);
		} else {
			otg->gadget = NULL;
		}
	}

	return 0;
}

/**
 * dwc3_ext_chg_det_done - callback to handle charger detection completion
 * @otg: Pointer to the otg transceiver structure
 * @charger: Pointer to the external charger structure
 *
 * Returns 0 on success
 */
static void dwc3_ext_chg_det_done(struct usb_otg *otg, struct dwc3_charger *chg)
{
	struct dwc3_otg *dotg = container_of(otg, struct dwc3_otg, otg);

	/*
	 * Ignore chg_detection notification if BSV has gone off by this time.
	 * STOP chg_det as part of !BSV handling would reset the chg_det flags
	 */
	if (test_bit(B_SESS_VLD, &dotg->inputs))
		schedule_work(&dotg->sm_work);
}

/**
 * dwc3_set_charger - bind/unbind external charger driver
 * @otg: Pointer to the otg transceiver structure
 * @charger: Pointer to the external charger structure
 *
 * Returns 0 on success
 */
int dwc3_set_charger(struct usb_otg *otg, struct dwc3_charger *charger)
{
	struct dwc3_otg *dotg = container_of(otg, struct dwc3_otg, otg);

	dotg->charger = charger;
	if (charger)
		charger->notify_detection_complete = dwc3_ext_chg_det_done;

	return 0;
}

/**
 * dwc3_ext_event_notify - callback to handle events from external transceiver
 * @otg: Pointer to the otg transceiver structure
 * @event: Event reported by transceiver
 *
 * Returns 0 on success
 */
static void dwc3_ext_event_notify(struct usb_otg *otg,
					enum dwc3_ext_events event)
{
	static bool init;
	struct dwc3_otg *dotg = container_of(otg, struct dwc3_otg, otg);
	struct dwc3_ext_xceiv *ext_xceiv = dotg->ext_xceiv;
	struct usb_phy *phy = dotg->otg.phy;
	int ret = 0;

	/* Flush processing any pending events before handling new ones */
	if (init)
		flush_work(&dotg->sm_work);

	if (event == DWC3_EVENT_PHY_RESUME) {
		if (!pm_runtime_status_suspended(phy->dev)) {
			dev_warn(phy->dev, "PHY_RESUME event out of LPM!!!!\n");
		} else {
			dev_dbg(phy->dev, "ext PHY_RESUME event received\n");
			/* ext_xceiver would have taken h/w out of LPM by now */
			ret = pm_runtime_get(phy->dev);
			if ((phy->state == OTG_STATE_A_HOST) &&
							dotg->host_bus_suspend)
				dotg->host_bus_suspend = 0;
			if (ret == -EACCES) {
				/* pm_runtime_get may fail during system
				   resume with -EACCES error */
				pm_runtime_disable(phy->dev);
				pm_runtime_set_active(phy->dev);
				pm_runtime_enable(phy->dev);
			} else if (ret < 0) {
				dev_warn(phy->dev, "pm_runtime_get failed!\n");
			}
		}
	} else if (event == DWC3_EVENT_XCEIV_STATE) {
		if (pm_runtime_status_suspended(phy->dev)) {
			dev_warn(phy->dev, "PHY_STATE event in LPM!!!!\n");
			ret = pm_runtime_get(phy->dev);
			if (ret < 0)
				dev_warn(phy->dev, "pm_runtime_get failed!!\n");
		}
		if (ext_xceiv->id == DWC3_ID_FLOAT) {
			dev_dbg(phy->dev, "XCVR: ID set\n");
			set_bit(ID, &dotg->inputs);
		} else {
			dev_dbg(phy->dev, "XCVR: ID clear\n");
			clear_bit(ID, &dotg->inputs);
		}

		if (ext_xceiv->bsv) {
			dev_dbg(phy->dev, "XCVR: BSV set\n");
			set_bit(B_SESS_VLD, &dotg->inputs);
		} else {
			dev_dbg(phy->dev, "XCVR: BSV clear\n");
			clear_bit(B_SESS_VLD, &dotg->inputs);
		}

		if (!init) {
			init = true;
			if (!work_busy(&dotg->sm_work))
				schedule_work(&dotg->sm_work);

			complete(&dotg->dwc3_xcvr_vbus_init);
			dev_dbg(phy->dev, "XCVR: BSV init complete\n");
			return;
		}

		schedule_work(&dotg->sm_work);
	}
}

/**
 * dwc3_set_ext_xceiv - bind/unbind external transceiver driver
 * @otg: Pointer to the otg transceiver structure
 * @ext_xceiv: Pointer to the external transceiver struccture
 *
 * Returns 0 on success
 */
int dwc3_set_ext_xceiv(struct usb_otg *otg, struct dwc3_ext_xceiv *ext_xceiv)
{
	struct dwc3_otg *dotg = container_of(otg, struct dwc3_otg, otg);

	dotg->ext_xceiv = ext_xceiv;
	if (ext_xceiv)
		ext_xceiv->notify_ext_events = dwc3_ext_event_notify;

	return 0;
}

static void dwc3_otg_notify_host_mode(struct usb_otg *otg, int host_mode)
{
	struct dwc3_otg *dotg = container_of(otg, struct dwc3_otg, otg);

	if (!dotg->psy) {
		dev_err(otg->phy->dev, "no usb power supply registered\n");
		return;
	}

	if (host_mode)
		power_supply_set_scope(dotg->psy, POWER_SUPPLY_SCOPE_SYSTEM);
	else
		power_supply_set_scope(dotg->psy, POWER_SUPPLY_SCOPE_DEVICE);
}

static int dwc3_otg_set_power(struct usb_phy *phy, unsigned mA)
{
	static int power_supply_type;
	struct dwc3_otg *dotg = container_of(phy->otg, struct dwc3_otg, otg);


	if (!dotg->psy || !dotg->charger) {
		dev_err(phy->dev, "no usb power supply/charger registered\n");
		return 0;
	}

	if (dotg->charger->charging_disabled)
		return 0;

	if (dotg->charger->chg_type == DWC3_SDP_CHARGER)
		power_supply_type = POWER_SUPPLY_TYPE_USB;
	else if (dotg->charger->chg_type == DWC3_CDP_CHARGER)
		power_supply_type = POWER_SUPPLY_TYPE_USB_CDP;
	else if (dotg->charger->chg_type == DWC3_DCP_CHARGER ||
			dotg->charger->chg_type == DWC3_PROPRIETARY_CHARGER)
		power_supply_type = POWER_SUPPLY_TYPE_USB_DCP;
	else
		power_supply_type = POWER_SUPPLY_TYPE_BATTERY;

	power_supply_set_supply_type(dotg->psy, power_supply_type);

	if ((dotg->charger->chg_type == DWC3_CDP_CHARGER) && mA > 2)
		mA = DWC3_IDEV_CHG_MAX;

	if (dotg->charger->max_power == mA)
		return 0;

	dev_info(phy->dev, "Avail curr from USB = %u\n", mA);

	if (dotg->charger->max_power <= 2 && mA > 2) {
		/* Enable charging */
		if (power_supply_set_online(dotg->psy, true))
			goto psy_error;
		if (power_supply_set_current_limit(dotg->psy, 1000*mA))
			goto psy_error;
	} else if (dotg->charger->max_power > 0 && (mA == 0 || mA == 2)) {
		/* Disable charging */
		if (power_supply_set_online(dotg->psy, false))
			goto psy_error;
		/* Set max current limit */
		if (power_supply_set_current_limit(dotg->psy, 0))
			goto psy_error;
	}

	power_supply_changed(dotg->psy);
	dotg->charger->max_power = mA;
	return 0;

psy_error:
	dev_dbg(phy->dev, "power supply error when setting property\n");
	return -ENXIO;
}

/* IRQs which OTG driver is interested in handling */
#define DWC3_OEVT_MASK		(DWC3_OEVTEN_OTGCONIDSTSCHNGEVNT | \
				 DWC3_OEVTEN_OTGBDEVVBUSCHNGEVNT)

/**
 * dwc3_otg_interrupt - interrupt handler for dwc3 otg events.
 * @_dotg: Pointer to out controller context structure
 *
 * Returns IRQ_HANDLED on success otherwise IRQ_NONE.
 */
static irqreturn_t dwc3_otg_interrupt(int irq, void *_dotg)
{
	struct dwc3_otg *dotg = (struct dwc3_otg *)_dotg;
	u32 osts, oevt_reg;
	int ret = IRQ_NONE;
	int handled_irqs = 0;
	struct usb_phy *phy = dotg->otg.phy;

	oevt_reg = dwc3_readl(dotg->regs, DWC3_OEVT);

	if (!(oevt_reg & DWC3_OEVT_MASK))
		return IRQ_NONE;

	osts = dwc3_readl(dotg->regs, DWC3_OSTS);

	if ((oevt_reg & DWC3_OEVTEN_OTGCONIDSTSCHNGEVNT) ||
	    (oevt_reg & DWC3_OEVTEN_OTGBDEVVBUSCHNGEVNT)) {
		/*
		 * ID sts has changed, set inputs later, in the workqueue
		 * function, switch from A to B or from B to A.
		 */

		if (oevt_reg & DWC3_OEVTEN_OTGCONIDSTSCHNGEVNT) {
			if (osts & DWC3_OTG_OSTS_CONIDSTS) {
				dev_dbg(phy->dev, "ID set\n");
				set_bit(ID, &dotg->inputs);
			} else {
				dev_dbg(phy->dev, "ID clear\n");
				clear_bit(ID, &dotg->inputs);
			}
			handled_irqs |= DWC3_OEVTEN_OTGCONIDSTSCHNGEVNT;
		}

		if (oevt_reg & DWC3_OEVTEN_OTGBDEVVBUSCHNGEVNT) {
			if (osts & DWC3_OTG_OSTS_BSESVALID) {
				dev_dbg(phy->dev, "BSV set\n");
				set_bit(B_SESS_VLD, &dotg->inputs);
			} else {
				dev_dbg(phy->dev, "BSV clear\n");
				clear_bit(B_SESS_VLD, &dotg->inputs);
			}
			handled_irqs |= DWC3_OEVTEN_OTGBDEVVBUSCHNGEVNT;
		}

		schedule_work(&dotg->sm_work);

		ret = IRQ_HANDLED;

		/* Clear the interrupts we handled */
		dwc3_writel(dotg->regs, DWC3_OEVT, handled_irqs);
	}

	return ret;
}

/**
 * dwc3_otg_init_sm - initialize OTG statemachine input
 * @dotg: Pointer to the dwc3_otg structure
 *
 */
void dwc3_otg_init_sm(struct dwc3_otg *dotg)
{
	u32 osts = dwc3_readl(dotg->regs, DWC3_OSTS);
	struct usb_phy *phy = dotg->otg.phy;
	struct dwc3_ext_xceiv *ext_xceiv;
	int ret;

	dev_dbg(phy->dev, "Initialize OTG inputs, osts: 0x%x\n", osts);

	/*
	 * VBUS initial state is reported after PMIC
	 * driver initialization. Wait for it.
	 */
	ret = wait_for_completion_timeout(&dotg->dwc3_xcvr_vbus_init, HZ * 5);
	if (!ret) {
		dev_err(phy->dev, "%s: completion timeout\n", __func__);
		/* We can safely assume no cable connected */
		set_bit(ID, &dotg->inputs);
	}

	ext_xceiv = dotg->ext_xceiv;
	dwc3_otg_reset(dotg);
	if (ext_xceiv && !ext_xceiv->otg_capability) {
		if (osts & DWC3_OTG_OSTS_CONIDSTS)
			set_bit(ID, &dotg->inputs);
		else
			clear_bit(ID, &dotg->inputs);

		if (osts & DWC3_OTG_OSTS_BSESVALID)
			set_bit(B_SESS_VLD, &dotg->inputs);
		else
			clear_bit(B_SESS_VLD, &dotg->inputs);
	}
}

/**
 * dwc3_otg_sm_work - workqueue function.
 *
 * @w: Pointer to the dwc3 otg workqueue
 *
 * NOTE: After any change in phy->state,
 * we must reschdule the state machine.
 */
static void dwc3_otg_sm_work(struct work_struct *w)
{
	struct dwc3_otg *dotg = container_of(w, struct dwc3_otg, sm_work);
	struct usb_phy *phy = dotg->otg.phy;
	struct dwc3_charger *charger = dotg->charger;
	bool work = 0;

	pm_runtime_resume(phy->dev);
	dev_dbg(phy->dev, "%s state\n", otg_state_string(phy->state));

	/* Check OTG state */
	switch (phy->state) {
	case OTG_STATE_UNDEFINED:
		dwc3_otg_init_sm(dotg);
		if (!dotg->psy) {
			dotg->psy = power_supply_get_by_name("usb");

			if (!dotg->psy)
				dev_err(phy->dev,
					 "couldn't get usb power supply\n");
		}

		/* Switch to A or B-Device according to ID / BSV */
		if (!test_bit(ID, &dotg->inputs)) {
			dev_dbg(phy->dev, "!id\n");
			phy->state = OTG_STATE_A_IDLE;
			work = 1;
		} else if (test_bit(B_SESS_VLD, &dotg->inputs)) {
			dev_dbg(phy->dev, "b_sess_vld\n");
			phy->state = OTG_STATE_B_IDLE;
			work = 1;
		} else {
			phy->state = OTG_STATE_B_IDLE;
			dev_dbg(phy->dev, "No device, trying to suspend\n");
			pm_runtime_put_sync(phy->dev);
		}
		break;

	case OTG_STATE_B_IDLE:
		if (!test_bit(ID, &dotg->inputs)) {
			dev_dbg(phy->dev, "!id\n");
			phy->state = OTG_STATE_A_IDLE;
			work = 1;
			if (charger) {
				if (charger->chg_type == DWC3_INVALID_CHARGER)
					charger->start_detection(dotg->charger,
									false);
				else
					charger->chg_type =
							DWC3_INVALID_CHARGER;
			}
		} else if (test_bit(B_SESS_VLD, &dotg->inputs)) {
			dev_dbg(phy->dev, "b_sess_vld\n");
			if (charger) {
				/* Has charger been detected? If no detect it */
				switch (charger->chg_type) {
				case DWC3_DCP_CHARGER:
				case DWC3_PROPRIETARY_CHARGER:
					dev_dbg(phy->dev, "lpm, DCP charger\n");
					dwc3_otg_set_power(phy,
							DWC3_IDEV_CHG_MAX);
					pm_runtime_put_sync(phy->dev);
					break;
				case DWC3_CDP_CHARGER:
					dwc3_otg_set_power(phy,
							DWC3_IDEV_CHG_MAX);
					dwc3_otg_start_peripheral(&dotg->otg,
									1);
					phy->state = OTG_STATE_B_PERIPHERAL;
					work = 1;
					break;
				case DWC3_SDP_CHARGER:
					dwc3_otg_start_peripheral(&dotg->otg,
									1);
					phy->state = OTG_STATE_B_PERIPHERAL;
					work = 1;
					break;
				default:
					dev_dbg(phy->dev, "chg_det started\n");
					charger->start_detection(charger, true);
					break;
				}
			} else {
				/* no charger registered, start peripheral */
				if (dwc3_otg_start_peripheral(&dotg->otg, 1)) {
					/*
					 * Probably set_peripheral not called
					 * yet. We will re-try as soon as it
					 * will be called
					 */
					dev_err(phy->dev, "enter lpm as\n"
						"unable to start B-device\n");
					phy->state = OTG_STATE_UNDEFINED;
					pm_runtime_put_sync(phy->dev);
					return;
				}
			}
		} else {
			if (charger)
				charger->start_detection(dotg->charger, false);

			dwc3_otg_set_power(phy, 0);
			dev_dbg(phy->dev, "No device, trying to suspend\n");
			pm_runtime_put_sync(phy->dev);
		}
		break;

	case OTG_STATE_B_PERIPHERAL:
		if (!test_bit(B_SESS_VLD, &dotg->inputs) ||
				!test_bit(ID, &dotg->inputs)) {
			dev_dbg(phy->dev, "!id || !bsv\n");
			dwc3_otg_start_peripheral(&dotg->otg, 0);
			phy->state = OTG_STATE_B_IDLE;
			if (charger)
				charger->chg_type = DWC3_INVALID_CHARGER;
			work = 1;
		}
		break;

	case OTG_STATE_A_IDLE:
		/* Switch to A-Device*/
		if (test_bit(ID, &dotg->inputs)) {
			dev_dbg(phy->dev, "id\n");
			phy->state = OTG_STATE_B_IDLE;
			work = 1;
		} else {
			phy->state = OTG_STATE_A_HOST;
			if (dwc3_otg_start_host(&dotg->otg, 1)) {
				/*
				 * Probably set_host was not called yet.
				 * We will re-try as soon as it will be called
				 */
				dev_dbg(phy->dev, "enter lpm as\n"
					"unable to start A-device\n");
				phy->state = OTG_STATE_UNDEFINED;
				pm_runtime_put_sync(phy->dev);
				return;
			}
		}
		break;

	case OTG_STATE_A_HOST:
		if (test_bit(ID, &dotg->inputs)) {
			dev_dbg(phy->dev, "id\n");
			dwc3_otg_start_host(&dotg->otg, 0);
			phy->state = OTG_STATE_B_IDLE;
			work = 1;
		}
		break;

	default:
		dev_err(phy->dev, "%s: invalid otg-state\n", __func__);

	}

	if (work)
		schedule_work(&dotg->sm_work);
}


/**
 * dwc3_otg_reset - reset dwc3 otg registers.
 *
 * @w: Pointer to the dwc3 otg workqueue
 */
static void dwc3_otg_reset(struct dwc3_otg *dotg)
{
	static int once;
	struct dwc3_ext_xceiv *ext_xceiv = dotg->ext_xceiv;

	/*
	 * OCFG[2] - OTG-Version = 1
	 * OCFG[1] - HNPCap = 0
	 * OCFG[0] - SRPCap = 0
	 */
	dwc3_writel(dotg->regs, DWC3_OCFG, 0x4);

	/*
	 * OCTL[6] - PeriMode = 1
	 * OCTL[5] - PrtPwrCtl = 0
	 * OCTL[4] - HNPReq = 0
	 * OCTL[3] - SesReq = 0
	 * OCTL[2] - TermSelDLPulse = 0
	 * OCTL[1] - DevSetHNPEn = 0
	 * OCTL[0] - HstSetHNPEn = 0
	 */
	if (!once) {
		dwc3_writel(dotg->regs, DWC3_OCTL, 0x40);
		once++;
	}

	/* Clear all otg events (interrupts) indications  */
	dwc3_writel(dotg->regs, DWC3_OEVT, 0xFFFF);

	/* Enable ID/BSV StsChngEn event*/
	if (ext_xceiv && !ext_xceiv->otg_capability)
		dwc3_writel(dotg->regs, DWC3_OEVTEN,
				DWC3_OEVTEN_OTGCONIDSTSCHNGEVNT |
				DWC3_OEVTEN_OTGBDEVVBUSCHNGEVNT);
}

/**
 * dwc3_otg_init - Initializes otg related registers
 * @dwc: Pointer to out controller context structure
 *
 * Returns 0 on success otherwise negative errno.
 */
int dwc3_otg_init(struct dwc3 *dwc)
{
	u32	reg;
	int ret = 0;
	struct dwc3_otg *dotg;

	dev_dbg(dwc->dev, "dwc3_otg_init\n");

	/*
	 * GHWPARAMS6[10] bit is SRPSupport.
	 * This bit also reflects DWC_USB3_EN_OTG
	 */
	reg = dwc3_readl(dwc->regs, DWC3_GHWPARAMS6);
	if (!(reg & DWC3_GHWPARAMS6_SRP_SUPPORT)) {
		/*
		 * No OTG support in the HW core.
		 * We return 0 to indicate no error, since this is acceptable
		 * situation, just continue probe the dwc3 driver without otg.
		 */
		dev_dbg(dwc->dev, "dwc3_otg address space is not supported\n");
		return 0;
	}

	/* Allocate and init otg instance */
	dotg = kzalloc(sizeof(struct dwc3_otg), GFP_KERNEL);
	if (!dotg) {
		dev_err(dwc->dev, "unable to allocate dwc3_otg\n");
		return -ENOMEM;
	}

	/* DWC3 has separate IRQ line for OTG events (ID/BSV etc.) */
	dotg->irq = platform_get_irq_byname(to_platform_device(dwc->dev),
								"otg_irq");
	if (dotg->irq < 0) {
		dev_err(dwc->dev, "%s: missing OTG IRQ\n", __func__);
		ret = -ENODEV;
		goto err1;
	}

	dotg->regs = dwc->regs;

	dotg->otg.set_peripheral = dwc3_otg_set_peripheral;
	dotg->otg.set_host = dwc3_otg_set_host;

	/* This reference is used by dwc3 modules for checking otg existance */
	dwc->dotg = dotg;

	dotg->otg.phy = kzalloc(sizeof(struct usb_phy), GFP_KERNEL);
	if (!dotg->otg.phy) {
		dev_err(dwc->dev, "unable to allocate dwc3_otg.phy\n");
		ret = -ENOMEM;
		goto err1;
	}

	dotg->dwc = dwc;
	dotg->otg.phy->otg = &dotg->otg;
	dotg->otg.phy->dev = dwc->dev;
	dotg->otg.phy->set_power = dwc3_otg_set_power;
	dotg->otg.phy->set_suspend = dwc3_otg_set_suspend;

	ret = usb_set_transceiver(dotg->otg.phy);
	if (ret) {
		dev_err(dotg->otg.phy->dev,
			"%s: failed to set transceiver, already exists\n",
			__func__);
		goto err2;
	}

	dotg->otg.phy->state = OTG_STATE_UNDEFINED;

	init_completion(&dotg->dwc3_xcvr_vbus_init);
	INIT_WORK(&dotg->sm_work, dwc3_otg_sm_work);

	ret = request_irq(dotg->irq, dwc3_otg_interrupt, IRQF_SHARED,
				"dwc3_otg", dotg);
	if (ret) {
		dev_err(dotg->otg.phy->dev, "failed to request irq #%d --> %d\n",
				dotg->irq, ret);
		goto err3;
	}

	pm_runtime_get(dwc->dev);

	return 0;

err3:
	cancel_work_sync(&dotg->sm_work);
	usb_set_transceiver(NULL);
err2:
	kfree(dotg->otg.phy);
err1:
	dwc->dotg = NULL;
	kfree(dotg);

	return ret;
}

/**
 * dwc3_otg_exit
 * @dwc: Pointer to out controller context structure
 *
 * Returns 0 on success otherwise negative errno.
 */
void dwc3_otg_exit(struct dwc3 *dwc)
{
	struct dwc3_otg *dotg = dwc->dotg;

	/* dotg is null when GHWPARAMS6[10]=SRPSupport=0, see dwc3_otg_init */
	if (dotg) {
		if (dotg->charger)
			dotg->charger->start_detection(dotg->charger, false);
		cancel_work_sync(&dotg->sm_work);
		usb_set_transceiver(NULL);
		pm_runtime_put(dwc->dev);
		free_irq(dotg->irq, dotg);
		kfree(dotg->otg.phy);
		kfree(dotg);
		dwc->dotg = NULL;
	}
}