| /* |
| * zs.h: Definitions for the DECstation Z85C30 serial driver. |
| * |
| * Adapted from drivers/sbus/char/sunserial.h by Paul Mackerras. |
| * Adapted from drivers/macintosh/macserial.h by Harald Koerfgen. |
| * |
| * Copyright (C) 1996 Paul Mackerras (Paul.Mackerras@cs.anu.edu.au) |
| * Copyright (C) 1995 David S. Miller (davem@caip.rutgers.edu) |
| * Copyright (C) 2004, 2005, 2007 Maciej W. Rozycki |
| */ |
| #ifndef _SERIAL_ZS_H |
| #define _SERIAL_ZS_H |
| |
| #ifdef __KERNEL__ |
| |
| #define ZS_NUM_REGS 16 |
| |
| /* |
| * This is our internal structure for each serial port's state. |
| */ |
| struct zs_port { |
| struct zs_scc *scc; /* Containing SCC. */ |
| struct uart_port port; /* Underlying UART. */ |
| |
| int clk_mode; /* May be 1, 16, 32, or 64. */ |
| |
| unsigned int tty_break; /* Set on BREAK condition. */ |
| int tx_stopped; /* Output is suspended. */ |
| |
| unsigned int mctrl; /* State of modem lines. */ |
| u8 brk; /* BREAK state from RR0. */ |
| |
| u8 regs[ZS_NUM_REGS]; /* Channel write registers. */ |
| }; |
| |
| /* |
| * Per-SCC state for locking and the interrupt handler. |
| */ |
| struct zs_scc { |
| struct zs_port zport[2]; |
| spinlock_t zlock; |
| atomic_t irq_guard; |
| int initialised; |
| }; |
| |
| #endif /* __KERNEL__ */ |
| |
| /* |
| * Conversion routines to/from brg time constants from/to bits per second. |
| */ |
| #define ZS_BRG_TO_BPS(brg, freq) ((freq) / 2 / ((brg) + 2)) |
| #define ZS_BPS_TO_BRG(bps, freq) ((((freq) + (bps)) / (2 * (bps))) - 2) |
| |
| /* |
| * The Zilog register set. |
| */ |
| |
| /* Write Register 0 (Command) */ |
| #define R0 0 /* Register selects */ |
| #define R1 1 |
| #define R2 2 |
| #define R3 3 |
| #define R4 4 |
| #define R5 5 |
| #define R6 6 |
| #define R7 7 |
| #define R8 8 |
| #define R9 9 |
| #define R10 10 |
| #define R11 11 |
| #define R12 12 |
| #define R13 13 |
| #define R14 14 |
| #define R15 15 |
| |
| #define NULLCODE 0 /* Null Code */ |
| #define POINT_HIGH 0x8 /* Select upper half of registers */ |
| #define RES_EXT_INT 0x10 /* Reset Ext. Status Interrupts */ |
| #define SEND_ABORT 0x18 /* HDLC Abort */ |
| #define RES_RxINT_FC 0x20 /* Reset RxINT on First Character */ |
| #define RES_Tx_P 0x28 /* Reset TxINT Pending */ |
| #define ERR_RES 0x30 /* Error Reset */ |
| #define RES_H_IUS 0x38 /* Reset highest IUS */ |
| |
| #define RES_Rx_CRC 0x40 /* Reset Rx CRC Checker */ |
| #define RES_Tx_CRC 0x80 /* Reset Tx CRC Checker */ |
| #define RES_EOM_L 0xC0 /* Reset EOM latch */ |
| |
| /* Write Register 1 (Tx/Rx/Ext Int Enable and WAIT/DMA Commands) */ |
| #define EXT_INT_ENAB 0x1 /* Ext Int Enable */ |
| #define TxINT_ENAB 0x2 /* Tx Int Enable */ |
| #define PAR_SPEC 0x4 /* Parity is special condition */ |
| |
| #define RxINT_DISAB 0 /* Rx Int Disable */ |
| #define RxINT_FCERR 0x8 /* Rx Int on First Character Only or Error */ |
| #define RxINT_ALL 0x10 /* Int on all Rx Characters or error */ |
| #define RxINT_ERR 0x18 /* Int on error only */ |
| #define RxINT_MASK 0x18 |
| |
| #define WT_RDY_RT 0x20 /* Wait/Ready on R/T */ |
| #define WT_FN_RDYFN 0x40 /* Wait/FN/Ready FN */ |
| #define WT_RDY_ENAB 0x80 /* Wait/Ready Enable */ |
| |
| /* Write Register 2 (Interrupt Vector) */ |
| |
| /* Write Register 3 (Receive Parameters and Control) */ |
| #define RxENABLE 0x1 /* Rx Enable */ |
| #define SYNC_L_INH 0x2 /* Sync Character Load Inhibit */ |
| #define ADD_SM 0x4 /* Address Search Mode (SDLC) */ |
| #define RxCRC_ENAB 0x8 /* Rx CRC Enable */ |
| #define ENT_HM 0x10 /* Enter Hunt Mode */ |
| #define AUTO_ENAB 0x20 /* Auto Enables */ |
| #define Rx5 0x0 /* Rx 5 Bits/Character */ |
| #define Rx7 0x40 /* Rx 7 Bits/Character */ |
| #define Rx6 0x80 /* Rx 6 Bits/Character */ |
| #define Rx8 0xc0 /* Rx 8 Bits/Character */ |
| #define RxNBITS_MASK 0xc0 |
| |
| /* Write Register 4 (Transmit/Receive Miscellaneous Parameters and Modes) */ |
| #define PAR_ENA 0x1 /* Parity Enable */ |
| #define PAR_EVEN 0x2 /* Parity Even/Odd* */ |
| |
| #define SYNC_ENAB 0 /* Sync Modes Enable */ |
| #define SB1 0x4 /* 1 stop bit/char */ |
| #define SB15 0x8 /* 1.5 stop bits/char */ |
| #define SB2 0xc /* 2 stop bits/char */ |
| #define SB_MASK 0xc |
| |
| #define MONSYNC 0 /* 8 Bit Sync character */ |
| #define BISYNC 0x10 /* 16 bit sync character */ |
| #define SDLC 0x20 /* SDLC Mode (01111110 Sync Flag) */ |
| #define EXTSYNC 0x30 /* External Sync Mode */ |
| |
| #define X1CLK 0x0 /* x1 clock mode */ |
| #define X16CLK 0x40 /* x16 clock mode */ |
| #define X32CLK 0x80 /* x32 clock mode */ |
| #define X64CLK 0xc0 /* x64 clock mode */ |
| #define XCLK_MASK 0xc0 |
| |
| /* Write Register 5 (Transmit Parameters and Controls) */ |
| #define TxCRC_ENAB 0x1 /* Tx CRC Enable */ |
| #define RTS 0x2 /* RTS */ |
| #define SDLC_CRC 0x4 /* SDLC/CRC-16 */ |
| #define TxENAB 0x8 /* Tx Enable */ |
| #define SND_BRK 0x10 /* Send Break */ |
| #define Tx5 0x0 /* Tx 5 bits (or less)/character */ |
| #define Tx7 0x20 /* Tx 7 bits/character */ |
| #define Tx6 0x40 /* Tx 6 bits/character */ |
| #define Tx8 0x60 /* Tx 8 bits/character */ |
| #define TxNBITS_MASK 0x60 |
| #define DTR 0x80 /* DTR */ |
| |
| /* Write Register 6 (Sync bits 0-7/SDLC Address Field) */ |
| |
| /* Write Register 7 (Sync bits 8-15/SDLC 01111110) */ |
| |
| /* Write Register 8 (Transmit Buffer) */ |
| |
| /* Write Register 9 (Master Interrupt Control) */ |
| #define VIS 1 /* Vector Includes Status */ |
| #define NV 2 /* No Vector */ |
| #define DLC 4 /* Disable Lower Chain */ |
| #define MIE 8 /* Master Interrupt Enable */ |
| #define STATHI 0x10 /* Status high */ |
| #define SOFTACK 0x20 /* Software Interrupt Acknowledge */ |
| #define NORESET 0 /* No reset on write to R9 */ |
| #define CHRB 0x40 /* Reset channel B */ |
| #define CHRA 0x80 /* Reset channel A */ |
| #define FHWRES 0xc0 /* Force hardware reset */ |
| |
| /* Write Register 10 (Miscellaneous Transmitter/Receiver Control Bits) */ |
| #define BIT6 1 /* 6 bit/8bit sync */ |
| #define LOOPMODE 2 /* SDLC Loop mode */ |
| #define ABUNDER 4 /* Abort/flag on SDLC xmit underrun */ |
| #define MARKIDLE 8 /* Mark/flag on idle */ |
| #define GAOP 0x10 /* Go active on poll */ |
| #define NRZ 0 /* NRZ mode */ |
| #define NRZI 0x20 /* NRZI mode */ |
| #define FM1 0x40 /* FM1 (transition = 1) */ |
| #define FM0 0x60 /* FM0 (transition = 0) */ |
| #define CRCPS 0x80 /* CRC Preset I/O */ |
| |
| /* Write Register 11 (Clock Mode Control) */ |
| #define TRxCXT 0 /* TRxC = Xtal output */ |
| #define TRxCTC 1 /* TRxC = Transmit clock */ |
| #define TRxCBR 2 /* TRxC = BR Generator Output */ |
| #define TRxCDP 3 /* TRxC = DPLL output */ |
| #define TRxCOI 4 /* TRxC O/I */ |
| #define TCRTxCP 0 /* Transmit clock = RTxC pin */ |
| #define TCTRxCP 8 /* Transmit clock = TRxC pin */ |
| #define TCBR 0x10 /* Transmit clock = BR Generator output */ |
| #define TCDPLL 0x18 /* Transmit clock = DPLL output */ |
| #define RCRTxCP 0 /* Receive clock = RTxC pin */ |
| #define RCTRxCP 0x20 /* Receive clock = TRxC pin */ |
| #define RCBR 0x40 /* Receive clock = BR Generator output */ |
| #define RCDPLL 0x60 /* Receive clock = DPLL output */ |
| #define RTxCX 0x80 /* RTxC Xtal/No Xtal */ |
| |
| /* Write Register 12 (Lower Byte of Baud Rate Generator Time Constant) */ |
| |
| /* Write Register 13 (Upper Byte of Baud Rate Generator Time Constant) */ |
| |
| /* Write Register 14 (Miscellaneous Control Bits) */ |
| #define BRENABL 1 /* Baud rate generator enable */ |
| #define BRSRC 2 /* Baud rate generator source */ |
| #define DTRREQ 4 /* DTR/Request function */ |
| #define AUTOECHO 8 /* Auto Echo */ |
| #define LOOPBAK 0x10 /* Local loopback */ |
| #define SEARCH 0x20 /* Enter search mode */ |
| #define RMC 0x40 /* Reset missing clock */ |
| #define DISDPLL 0x60 /* Disable DPLL */ |
| #define SSBR 0x80 /* Set DPLL source = BR generator */ |
| #define SSRTxC 0xa0 /* Set DPLL source = RTxC */ |
| #define SFMM 0xc0 /* Set FM mode */ |
| #define SNRZI 0xe0 /* Set NRZI mode */ |
| |
| /* Write Register 15 (External/Status Interrupt Control) */ |
| #define WR7P_EN 1 /* WR7 Prime SDLC Feature Enable */ |
| #define ZCIE 2 /* Zero count IE */ |
| #define DCDIE 8 /* DCD IE */ |
| #define SYNCIE 0x10 /* Sync/hunt IE */ |
| #define CTSIE 0x20 /* CTS IE */ |
| #define TxUIE 0x40 /* Tx Underrun/EOM IE */ |
| #define BRKIE 0x80 /* Break/Abort IE */ |
| |
| |
| /* Read Register 0 (Transmit/Receive Buffer Status and External Status) */ |
| #define Rx_CH_AV 0x1 /* Rx Character Available */ |
| #define ZCOUNT 0x2 /* Zero count */ |
| #define Tx_BUF_EMP 0x4 /* Tx Buffer empty */ |
| #define DCD 0x8 /* DCD */ |
| #define SYNC_HUNT 0x10 /* Sync/hunt */ |
| #define CTS 0x20 /* CTS */ |
| #define TxEOM 0x40 /* Tx underrun */ |
| #define BRK_ABRT 0x80 /* Break/Abort */ |
| |
| /* Read Register 1 (Special Receive Condition Status) */ |
| #define ALL_SNT 0x1 /* All sent */ |
| /* Residue Data for 8 Rx bits/char programmed */ |
| #define RES3 0x8 /* 0/3 */ |
| #define RES4 0x4 /* 0/4 */ |
| #define RES5 0xc /* 0/5 */ |
| #define RES6 0x2 /* 0/6 */ |
| #define RES7 0xa /* 0/7 */ |
| #define RES8 0x6 /* 0/8 */ |
| #define RES18 0xe /* 1/8 */ |
| #define RES28 0x0 /* 2/8 */ |
| /* Special Rx Condition Interrupts */ |
| #define PAR_ERR 0x10 /* Parity Error */ |
| #define Rx_OVR 0x20 /* Rx Overrun Error */ |
| #define FRM_ERR 0x40 /* CRC/Framing Error */ |
| #define END_FR 0x80 /* End of Frame (SDLC) */ |
| |
| /* Read Register 2 (Interrupt Vector (WR2) -- channel A). */ |
| |
| /* Read Register 2 (Modified Interrupt Vector -- channel B). */ |
| |
| /* Read Register 3 (Interrupt Pending Bits -- channel A only). */ |
| #define CHBEXT 0x1 /* Channel B Ext/Stat IP */ |
| #define CHBTxIP 0x2 /* Channel B Tx IP */ |
| #define CHBRxIP 0x4 /* Channel B Rx IP */ |
| #define CHAEXT 0x8 /* Channel A Ext/Stat IP */ |
| #define CHATxIP 0x10 /* Channel A Tx IP */ |
| #define CHARxIP 0x20 /* Channel A Rx IP */ |
| |
| /* Read Register 6 (SDLC FIFO Status and Byte Count LSB) */ |
| |
| /* Read Register 7 (SDLC FIFO Status and Byte Count MSB) */ |
| |
| /* Read Register 8 (Receive Data) */ |
| |
| /* Read Register 10 (Miscellaneous Status Bits) */ |
| #define ONLOOP 2 /* On loop */ |
| #define LOOPSEND 0x10 /* Loop sending */ |
| #define CLK2MIS 0x40 /* Two clocks missing */ |
| #define CLK1MIS 0x80 /* One clock missing */ |
| |
| /* Read Register 12 (Lower Byte of Baud Rate Generator Constant (WR12)) */ |
| |
| /* Read Register 13 (Upper Byte of Baud Rate Generator Constant (WR13) */ |
| |
| /* Read Register 15 (External/Status Interrupt Control (WR15)) */ |
| |
| #endif /* _SERIAL_ZS_H */ |