| # |
| # USB Dual Role (OTG-ready) Controller Drivers |
| # for silicon based on Mentor Graphics INVENTRA designs |
| # |
| |
| comment "Enable Host or Gadget support to see Inventra options" |
| depends on !USB && USB_GADGET=n |
| |
| # (M)HDRC = (Multipoint) Highspeed Dual-Role Controller |
| config USB_MUSB_HDRC |
| depends on (USB || USB_GADGET) |
| depends on (ARM || (BF54x && !BF544) || (BF52x && !BF522 && !BF523)) |
| select NOP_USB_XCEIV if (ARCH_DAVINCI || MACH_OMAP3EVM || BLACKFIN) |
| select TWL4030_USB if MACH_OMAP_3430SDP |
| select TWL6030_USB if MACH_OMAP_4430SDP || MACH_OMAP4_PANDA |
| select USB_OTG_UTILS |
| tristate 'Inventra Highspeed Dual Role Controller (TI, ADI, ...)' |
| help |
| Say Y here if your system has a dual role high speed USB |
| controller based on the Mentor Graphics silicon IP. Then |
| configure options to match your silicon and the board |
| it's being used with, including the USB peripheral role, |
| or the USB host role, or both. |
| |
| Texas Instruments familiies using this IP include DaVinci |
| (35x, 644x ...), OMAP 243x, OMAP 3, and TUSB 6010. |
| |
| Analog Devices parts using this IP include Blackfin BF54x, |
| BF525 and BF527. |
| |
| If you do not know what this is, please say N. |
| |
| To compile this driver as a module, choose M here; the |
| module will be called "musb-hdrc". |
| |
| choice |
| prompt "Platform Glue Layer" |
| depends on USB_MUSB_HDRC |
| |
| config USB_MUSB_DAVINCI |
| tristate "DaVinci" |
| depends on ARCH_DAVINCI_DMx |
| |
| config USB_MUSB_DA8XX |
| tristate "DA8xx/OMAP-L1x" |
| depends on ARCH_DAVINCI_DA8XX |
| |
| config USB_MUSB_TUSB6010 |
| tristate "TUSB6010" |
| depends on ARCH_OMAP |
| |
| config USB_MUSB_OMAP2PLUS |
| tristate "OMAP2430 and onwards" |
| depends on ARCH_OMAP2PLUS |
| |
| config USB_MUSB_AM35X |
| tristate "AM35x" |
| depends on ARCH_OMAP |
| |
| config USB_MUSB_BLACKFIN |
| tristate "Blackfin" |
| depends on (BF54x && !BF544) || (BF52x && ! BF522 && !BF523) |
| |
| config USB_MUSB_UX500 |
| tristate "U8500 and U5500" |
| depends on (ARCH_U8500 && AB8500_USB) || (ARCH_U5500) |
| |
| endchoice |
| |
| choice |
| prompt "Driver Mode" |
| depends on USB_MUSB_HDRC |
| help |
| Dual-Role devices can support both host and peripheral roles, |
| as well as a the special "OTG Device" role which can switch |
| between both roles as needed. |
| |
| # use USB_MUSB_HDRC_HCD not USB_MUSB_HOST to #ifdef host side support; |
| # OTG needs both roles, not just USB_MUSB_HOST. |
| config USB_MUSB_HOST |
| depends on USB |
| bool "USB Host" |
| help |
| Say Y here if your system supports the USB host role. |
| If it has a USB "A" (rectangular), "Mini-A" (uncommon), |
| or "Mini-AB" connector, it supports the host role. |
| (With a "Mini-AB" connector, you should enable USB OTG.) |
| |
| # use USB_GADGET_MUSB_HDRC not USB_MUSB_PERIPHERAL to #ifdef peripheral |
| # side support ... OTG needs both roles |
| config USB_MUSB_PERIPHERAL |
| depends on USB_GADGET |
| bool "USB Peripheral (gadget stack)" |
| select USB_GADGET_MUSB_HDRC |
| help |
| Say Y here if your system supports the USB peripheral role. |
| If it has a USB "B" (squarish), "Mini-B", or "Mini-AB" |
| connector, it supports the peripheral role. |
| (With a "Mini-AB" connector, you should enable USB OTG.) |
| |
| config USB_MUSB_OTG |
| depends on USB && USB_GADGET && PM && EXPERIMENTAL |
| bool "Both host and peripheral: USB OTG (On The Go) Device" |
| select USB_GADGET_MUSB_HDRC |
| select USB_OTG |
| help |
| The most notable feature of USB OTG is support for a |
| "Dual-Role" device, which can act as either a device |
| or a host. The initial role choice can be changed |
| later, when two dual-role devices talk to each other. |
| |
| At this writing, the OTG support in this driver is incomplete, |
| omitting the mandatory HNP or SRP protocols. However, some |
| of the cable based role switching works. (That is, grounding |
| the ID pin switches the controller to host mode, while leaving |
| it floating leaves it in peripheral mode.) |
| |
| Select this if your system has a Mini-AB connector, or |
| to simplify certain kinds of configuration. |
| |
| To implement your OTG Targeted Peripherals List (TPL), enable |
| USB_OTG_WHITELIST and update "drivers/usb/core/otg_whitelist.h" |
| to match your requirements. |
| |
| endchoice |
| |
| # enable peripheral support (including with OTG) |
| config USB_GADGET_MUSB_HDRC |
| bool |
| depends on USB_MUSB_HDRC && (USB_MUSB_PERIPHERAL || USB_MUSB_OTG) |
| # default y |
| # select USB_GADGET_DUALSPEED |
| # select USB_GADGET_SELECTED |
| |
| # enables host support (including with OTG) |
| config USB_MUSB_HDRC_HCD |
| bool |
| depends on USB_MUSB_HDRC && (USB_MUSB_HOST || USB_MUSB_OTG) |
| select USB_OTG if USB_GADGET_MUSB_HDRC |
| default y |
| |
| |
| config MUSB_PIO_ONLY |
| bool 'Disable DMA (always use PIO)' |
| depends on USB_MUSB_HDRC |
| default USB_MUSB_TUSB6010 || USB_MUSB_DA8XX || USB_MUSB_AM35X |
| help |
| All data is copied between memory and FIFO by the CPU. |
| DMA controllers are ignored. |
| |
| Do not select 'n' here unless DMA support for your SOC or board |
| is unavailable (or unstable). When DMA is enabled at compile time, |
| you can still disable it at run time using the "use_dma=n" module |
| parameter. |
| |
| config USB_UX500_DMA |
| bool |
| depends on USB_MUSB_HDRC && !MUSB_PIO_ONLY |
| default USB_MUSB_UX500 |
| help |
| Enable DMA transfers on UX500 platforms. |
| |
| config USB_INVENTRA_DMA |
| bool |
| depends on USB_MUSB_HDRC && !MUSB_PIO_ONLY |
| default USB_MUSB_OMAP2PLUS || USB_MUSB_BLACKFIN |
| help |
| Enable DMA transfers using Mentor's engine. |
| |
| config USB_TI_CPPI_DMA |
| bool |
| depends on USB_MUSB_HDRC && !MUSB_PIO_ONLY |
| default USB_MUSB_DAVINCI |
| help |
| Enable DMA transfers when TI CPPI DMA is available. |
| |
| config USB_TUSB_OMAP_DMA |
| bool |
| depends on USB_MUSB_HDRC && !MUSB_PIO_ONLY |
| depends on USB_MUSB_TUSB6010 |
| depends on ARCH_OMAP |
| default y |
| help |
| Enable DMA transfers on TUSB 6010 when OMAP DMA is available. |
| |