| /* |
| * Freescale eSDHC i.MX controller driver for the platform bus. |
| * |
| * derived from the OF-version. |
| * |
| * Copyright (c) 2010 Pengutronix e.K. |
| * Author: Wolfram Sang <w.sang@pengutronix.de> |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License as published by |
| * the Free Software Foundation; either version 2 of the License. |
| */ |
| |
| #include <linux/io.h> |
| #include <linux/delay.h> |
| #include <linux/err.h> |
| #include <linux/clk.h> |
| #include <linux/gpio.h> |
| #include <linux/slab.h> |
| #include <linux/mmc/host.h> |
| #include <linux/mmc/mmc.h> |
| #include <linux/mmc/sdio.h> |
| #include <mach/hardware.h> |
| #include <mach/esdhc.h> |
| #include "sdhci-pltfm.h" |
| #include "sdhci-esdhc.h" |
| |
| /* VENDOR SPEC register */ |
| #define SDHCI_VENDOR_SPEC 0xC0 |
| #define SDHCI_VENDOR_SPEC_SDIO_QUIRK 0x00000002 |
| |
| #define ESDHC_FLAG_GPIO_FOR_CD (1 << 0) |
| /* |
| * The CMDTYPE of the CMD register (offset 0xE) should be set to |
| * "11" when the STOP CMD12 is issued on imx53 to abort one |
| * open ended multi-blk IO. Otherwise the TC INT wouldn't |
| * be generated. |
| * In exact block transfer, the controller doesn't complete the |
| * operations automatically as required at the end of the |
| * transfer and remains on hold if the abort command is not sent. |
| * As a result, the TC flag is not asserted and SW received timeout |
| * exeception. Bit1 of Vendor Spec registor is used to fix it. |
| */ |
| #define ESDHC_FLAG_MULTIBLK_NO_INT (1 << 1) |
| |
| struct pltfm_imx_data { |
| int flags; |
| u32 scratchpad; |
| }; |
| |
| static inline void esdhc_clrset_le(struct sdhci_host *host, u32 mask, u32 val, int reg) |
| { |
| void __iomem *base = host->ioaddr + (reg & ~0x3); |
| u32 shift = (reg & 0x3) * 8; |
| |
| writel(((readl(base) & ~(mask << shift)) | (val << shift)), base); |
| } |
| |
| static u32 esdhc_readl_le(struct sdhci_host *host, int reg) |
| { |
| struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); |
| struct pltfm_imx_data *imx_data = pltfm_host->priv; |
| |
| /* fake CARD_PRESENT flag on mx25/35 */ |
| u32 val = readl(host->ioaddr + reg); |
| |
| if (unlikely((reg == SDHCI_PRESENT_STATE) |
| && (imx_data->flags & ESDHC_FLAG_GPIO_FOR_CD))) { |
| struct esdhc_platform_data *boarddata = |
| host->mmc->parent->platform_data; |
| |
| if (boarddata && gpio_is_valid(boarddata->cd_gpio) |
| && gpio_get_value(boarddata->cd_gpio)) |
| /* no card, if a valid gpio says so... */ |
| val &= ~SDHCI_CARD_PRESENT; |
| else |
| /* ... in all other cases assume card is present */ |
| val |= SDHCI_CARD_PRESENT; |
| } |
| |
| return val; |
| } |
| |
| static void esdhc_writel_le(struct sdhci_host *host, u32 val, int reg) |
| { |
| struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); |
| struct pltfm_imx_data *imx_data = pltfm_host->priv; |
| |
| if (unlikely((reg == SDHCI_INT_ENABLE || reg == SDHCI_SIGNAL_ENABLE) |
| && (imx_data->flags & ESDHC_FLAG_GPIO_FOR_CD))) |
| /* |
| * these interrupts won't work with a custom card_detect gpio |
| * (only applied to mx25/35) |
| */ |
| val &= ~(SDHCI_INT_CARD_REMOVE | SDHCI_INT_CARD_INSERT); |
| |
| if (unlikely((imx_data->flags & ESDHC_FLAG_MULTIBLK_NO_INT) |
| && (reg == SDHCI_INT_STATUS) |
| && (val & SDHCI_INT_DATA_END))) { |
| u32 v; |
| v = readl(host->ioaddr + SDHCI_VENDOR_SPEC); |
| v &= ~SDHCI_VENDOR_SPEC_SDIO_QUIRK; |
| writel(v, host->ioaddr + SDHCI_VENDOR_SPEC); |
| } |
| |
| writel(val, host->ioaddr + reg); |
| } |
| |
| static u16 esdhc_readw_le(struct sdhci_host *host, int reg) |
| { |
| if (unlikely(reg == SDHCI_HOST_VERSION)) |
| reg ^= 2; |
| |
| return readw(host->ioaddr + reg); |
| } |
| |
| static void esdhc_writew_le(struct sdhci_host *host, u16 val, int reg) |
| { |
| struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); |
| struct pltfm_imx_data *imx_data = pltfm_host->priv; |
| |
| switch (reg) { |
| case SDHCI_TRANSFER_MODE: |
| /* |
| * Postpone this write, we must do it together with a |
| * command write that is down below. |
| */ |
| if ((imx_data->flags & ESDHC_FLAG_MULTIBLK_NO_INT) |
| && (host->cmd->opcode == SD_IO_RW_EXTENDED) |
| && (host->cmd->data->blocks > 1) |
| && (host->cmd->data->flags & MMC_DATA_READ)) { |
| u32 v; |
| v = readl(host->ioaddr + SDHCI_VENDOR_SPEC); |
| v |= SDHCI_VENDOR_SPEC_SDIO_QUIRK; |
| writel(v, host->ioaddr + SDHCI_VENDOR_SPEC); |
| } |
| imx_data->scratchpad = val; |
| return; |
| case SDHCI_COMMAND: |
| if ((host->cmd->opcode == MMC_STOP_TRANSMISSION) |
| && (imx_data->flags & ESDHC_FLAG_MULTIBLK_NO_INT)) |
| val |= SDHCI_CMD_ABORTCMD; |
| writel(val << 16 | imx_data->scratchpad, |
| host->ioaddr + SDHCI_TRANSFER_MODE); |
| return; |
| case SDHCI_BLOCK_SIZE: |
| val &= ~SDHCI_MAKE_BLKSZ(0x7, 0); |
| break; |
| } |
| esdhc_clrset_le(host, 0xffff, val, reg); |
| } |
| |
| static void esdhc_writeb_le(struct sdhci_host *host, u8 val, int reg) |
| { |
| u32 new_val; |
| |
| switch (reg) { |
| case SDHCI_POWER_CONTROL: |
| /* |
| * FSL put some DMA bits here |
| * If your board has a regulator, code should be here |
| */ |
| return; |
| case SDHCI_HOST_CONTROL: |
| /* FSL messed up here, so we can just keep those two */ |
| new_val = val & (SDHCI_CTRL_LED | SDHCI_CTRL_4BITBUS); |
| /* ensure the endianess */ |
| new_val |= ESDHC_HOST_CONTROL_LE; |
| /* DMA mode bits are shifted */ |
| new_val |= (val & SDHCI_CTRL_DMA_MASK) << 5; |
| |
| esdhc_clrset_le(host, 0xffff, new_val, reg); |
| return; |
| } |
| esdhc_clrset_le(host, 0xff, val, reg); |
| } |
| |
| static unsigned int esdhc_pltfm_get_max_clock(struct sdhci_host *host) |
| { |
| struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); |
| |
| return clk_get_rate(pltfm_host->clk); |
| } |
| |
| static unsigned int esdhc_pltfm_get_min_clock(struct sdhci_host *host) |
| { |
| struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); |
| |
| return clk_get_rate(pltfm_host->clk) / 256 / 16; |
| } |
| |
| static struct sdhci_ops sdhci_esdhc_ops = { |
| .read_l = esdhc_readl_le, |
| .read_w = esdhc_readw_le, |
| .write_l = esdhc_writel_le, |
| .write_w = esdhc_writew_le, |
| .write_b = esdhc_writeb_le, |
| .set_clock = esdhc_set_clock, |
| .get_max_clock = esdhc_pltfm_get_max_clock, |
| .get_min_clock = esdhc_pltfm_get_min_clock, |
| }; |
| |
| static struct sdhci_pltfm_data sdhci_esdhc_imx_pdata = { |
| .quirks = ESDHC_DEFAULT_QUIRKS | SDHCI_QUIRK_BROKEN_ADMA |
| | SDHCI_QUIRK_BROKEN_CARD_DETECTION, |
| /* ADMA has issues. Might be fixable */ |
| .ops = &sdhci_esdhc_ops, |
| }; |
| |
| static unsigned int esdhc_pltfm_get_ro(struct sdhci_host *host) |
| { |
| struct esdhc_platform_data *boarddata = |
| host->mmc->parent->platform_data; |
| |
| if (boarddata && gpio_is_valid(boarddata->wp_gpio)) |
| return gpio_get_value(boarddata->wp_gpio); |
| else |
| return -ENOSYS; |
| } |
| |
| static irqreturn_t cd_irq(int irq, void *data) |
| { |
| struct sdhci_host *sdhost = (struct sdhci_host *)data; |
| |
| tasklet_schedule(&sdhost->card_tasklet); |
| return IRQ_HANDLED; |
| }; |
| |
| static int __devinit sdhci_esdhc_imx_probe(struct platform_device *pdev) |
| { |
| struct sdhci_pltfm_host *pltfm_host; |
| struct sdhci_host *host; |
| struct esdhc_platform_data *boarddata; |
| struct clk *clk; |
| int err; |
| struct pltfm_imx_data *imx_data; |
| |
| host = sdhci_pltfm_init(pdev, &sdhci_esdhc_imx_pdata); |
| if (IS_ERR(host)) |
| return PTR_ERR(host); |
| |
| pltfm_host = sdhci_priv(host); |
| |
| imx_data = kzalloc(sizeof(struct pltfm_imx_data), GFP_KERNEL); |
| if (!imx_data) |
| return -ENOMEM; |
| pltfm_host->priv = imx_data; |
| |
| clk = clk_get(mmc_dev(host->mmc), NULL); |
| if (IS_ERR(clk)) { |
| dev_err(mmc_dev(host->mmc), "clk err\n"); |
| err = PTR_ERR(clk); |
| goto err_clk_get; |
| } |
| clk_enable(clk); |
| pltfm_host->clk = clk; |
| |
| if (!cpu_is_mx25()) |
| host->quirks |= SDHCI_QUIRK_BROKEN_TIMEOUT_VAL; |
| |
| if (cpu_is_mx25() || cpu_is_mx35()) { |
| /* Fix errata ENGcm07207 present on i.MX25 and i.MX35 */ |
| host->quirks |= SDHCI_QUIRK_NO_MULTIBLOCK; |
| /* write_protect can't be routed to controller, use gpio */ |
| sdhci_esdhc_ops.get_ro = esdhc_pltfm_get_ro; |
| } |
| |
| if (!(cpu_is_mx25() || cpu_is_mx35() || cpu_is_mx51())) |
| imx_data->flags |= ESDHC_FLAG_MULTIBLK_NO_INT; |
| |
| boarddata = host->mmc->parent->platform_data; |
| if (boarddata) { |
| err = gpio_request_one(boarddata->wp_gpio, GPIOF_IN, "ESDHC_WP"); |
| if (err) { |
| dev_warn(mmc_dev(host->mmc), |
| "no write-protect pin available!\n"); |
| boarddata->wp_gpio = err; |
| } |
| |
| err = gpio_request_one(boarddata->cd_gpio, GPIOF_IN, "ESDHC_CD"); |
| if (err) { |
| dev_warn(mmc_dev(host->mmc), |
| "no card-detect pin available!\n"); |
| goto no_card_detect_pin; |
| } |
| |
| /* i.MX5x has issues to be researched */ |
| if (!cpu_is_mx25() && !cpu_is_mx35()) |
| goto not_supported; |
| |
| err = request_irq(gpio_to_irq(boarddata->cd_gpio), cd_irq, |
| IRQF_TRIGGER_FALLING | IRQF_TRIGGER_RISING, |
| mmc_hostname(host->mmc), host); |
| if (err) { |
| dev_warn(mmc_dev(host->mmc), "request irq error\n"); |
| goto no_card_detect_irq; |
| } |
| |
| imx_data->flags |= ESDHC_FLAG_GPIO_FOR_CD; |
| /* Now we have a working card_detect again */ |
| host->quirks &= ~SDHCI_QUIRK_BROKEN_CARD_DETECTION; |
| } |
| |
| err = sdhci_add_host(host); |
| if (err) |
| goto err_add_host; |
| |
| return 0; |
| |
| no_card_detect_irq: |
| gpio_free(boarddata->cd_gpio); |
| no_card_detect_pin: |
| boarddata->cd_gpio = err; |
| not_supported: |
| kfree(imx_data); |
| err_add_host: |
| clk_disable(pltfm_host->clk); |
| clk_put(pltfm_host->clk); |
| err_clk_get: |
| sdhci_pltfm_free(pdev); |
| return err; |
| } |
| |
| static int __devexit sdhci_esdhc_imx_remove(struct platform_device *pdev) |
| { |
| struct sdhci_host *host = platform_get_drvdata(pdev); |
| struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); |
| struct esdhc_platform_data *boarddata = host->mmc->parent->platform_data; |
| struct pltfm_imx_data *imx_data = pltfm_host->priv; |
| int dead = (readl(host->ioaddr + SDHCI_INT_STATUS) == 0xffffffff); |
| |
| sdhci_remove_host(host, dead); |
| |
| if (boarddata && gpio_is_valid(boarddata->wp_gpio)) |
| gpio_free(boarddata->wp_gpio); |
| |
| if (boarddata && gpio_is_valid(boarddata->cd_gpio)) { |
| gpio_free(boarddata->cd_gpio); |
| |
| if (!(host->quirks & SDHCI_QUIRK_BROKEN_CARD_DETECTION)) |
| free_irq(gpio_to_irq(boarddata->cd_gpio), host); |
| } |
| |
| clk_disable(pltfm_host->clk); |
| clk_put(pltfm_host->clk); |
| kfree(imx_data); |
| |
| sdhci_pltfm_free(pdev); |
| |
| return 0; |
| } |
| |
| static struct platform_driver sdhci_esdhc_imx_driver = { |
| .driver = { |
| .name = "sdhci-esdhc-imx", |
| .owner = THIS_MODULE, |
| }, |
| .probe = sdhci_esdhc_imx_probe, |
| .remove = __devexit_p(sdhci_esdhc_imx_remove), |
| #ifdef CONFIG_PM |
| .suspend = sdhci_pltfm_suspend, |
| .resume = sdhci_pltfm_resume, |
| #endif |
| }; |
| |
| static int __init sdhci_esdhc_imx_init(void) |
| { |
| return platform_driver_register(&sdhci_esdhc_imx_driver); |
| } |
| module_init(sdhci_esdhc_imx_init); |
| |
| static void __exit sdhci_esdhc_imx_exit(void) |
| { |
| platform_driver_unregister(&sdhci_esdhc_imx_driver); |
| } |
| module_exit(sdhci_esdhc_imx_exit); |
| |
| MODULE_DESCRIPTION("SDHCI driver for Freescale i.MX eSDHC"); |
| MODULE_AUTHOR("Wolfram Sang <w.sang@pengutronix.de>"); |
| MODULE_LICENSE("GPL v2"); |