| /* Copyright (c) 2012, Code Aurora Forum. All rights reserved. |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License version 2 and |
| * only version 2 as published by the Free Software Foundation. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| */ |
| |
| #define pr_fmt(fmt) "%s: " fmt, __func__ |
| |
| #include <linux/kernel.h> |
| #include <linux/of.h> |
| #include <linux/err.h> |
| #include <linux/init.h> |
| #include <linux/slab.h> |
| #include <linux/delay.h> |
| #include <linux/mutex.h> |
| #include <linux/types.h> |
| #include <linux/hwmon.h> |
| #include <linux/module.h> |
| #include <linux/debugfs.h> |
| #include <linux/spmi.h> |
| #include <linux/of_irq.h> |
| #include <linux/wakelock.h> |
| #include <linux/interrupt.h> |
| #include <linux/completion.h> |
| #include <linux/hwmon-sysfs.h> |
| #include <linux/qpnp/qpnp-adc.h> |
| #include <linux/platform_device.h> |
| |
| /* QPNP IADC register definition */ |
| #define QPNP_IADC_REVISION1 0x0 |
| #define QPNP_IADC_REVISION2 0x1 |
| #define QPNP_IADC_REVISION3 0x2 |
| #define QPNP_IADC_REVISION4 0x3 |
| #define QPNP_IADC_PERPH_TYPE 0x4 |
| #define QPNP_IADC_PERH_SUBTYPE 0x5 |
| |
| #define QPNP_IADC_SUPPORTED_REVISION2 1 |
| |
| #define QPNP_STATUS1 0x8 |
| #define QPNP_STATUS1_OP_MODE 4 |
| #define QPNP_STATUS1_MULTI_MEAS_EN BIT(3) |
| #define QPNP_STATUS1_MEAS_INTERVAL_EN_STS BIT(2) |
| #define QPNP_STATUS1_REQ_STS BIT(1) |
| #define QPNP_STATUS1_EOC BIT(0) |
| #define QPNP_STATUS2 0x9 |
| #define QPNP_STATUS2_CONV_SEQ_STATE_SHIFT 4 |
| #define QPNP_STATUS2_FIFO_NOT_EMPTY_FLAG BIT(1) |
| #define QPNP_STATUS2_CONV_SEQ_TIMEOUT_STS BIT(0) |
| #define QPNP_CONV_TIMEOUT_ERR 2 |
| |
| #define QPNP_INT_RT_ST 0x10 |
| #define QPNP_INT_SET_TYPE 0x11 |
| #define QPNP_INT_SET_TYPE_LOW_THR_INT_SET BIT(4) |
| #define QPNP_INT_SET_TYPE_HIGH_THR_INT_SET BIT(3) |
| #define QPNP_INT_SET_TYPE_CONV_SEQ_TIMEOUT_INT_SET BIT(2) |
| #define QPNP_INT_SET_TYPE_FIFO_NOT_EMPTY_INT_SET BIT(1) |
| #define QPNP_INT_SET_TYPE_EOC_SET_INT_TYPE BIT(0) |
| #define QPNP_INT_POLARITY_HIGH 0x12 |
| #define QPNP_INT_POLARITY_LOW 0x13 |
| #define QPNP_INT_EN_SET 0x15 |
| #define QPNP_INT_EN_SET_LOW_THR_INT_EN_SET BIT(4) |
| #define QPNP_INT_EN_SET_HIGH_THR_INT_EN_SET BIT(3) |
| #define QPNP_INT_EN_SET_CONV_SEQ_TIMEOUT_INT_EN BIT(2) |
| #define QPNP_INT_EN_SET_FIFO_NOT_EMPTY_INT_EN BIT(1) |
| #define QPNP_INT_EN_SET_EOC_INT_EN_SET BIT(0) |
| #define QPNP_INT_CLR 0x16 |
| #define QPNP_INT_CLR_LOW_THR_INT_EN_CLR BIT(4) |
| #define QPNP_INT_CLR_HIGH_THR_INT_EN_CLKR BIT(3) |
| #define QPNP_INT_CLR_CONV_SEQ_TIMEOUT_INT_EN BIT(2) |
| #define QPNP_INT_CLR_FIFO_NOT_EMPTY_INT_EN BIT(1) |
| #define QPNP_INT_CLR_EOC_INT_EN_CLR BIT(0) |
| #define QPNP_INT_CLR_MASK 0x1f |
| #define QPNP_IADC_MODE_CTL 0x40 |
| #define QPNP_OP_MODE_SHIFT 4 |
| #define QPNP_USE_BMS_DATA BIT(4) |
| #define QPNP_VADC_SYNCH_EN BIT(2) |
| #define QPNP_OFFSET_RMV_EN BIT(1) |
| #define QPNP_ADC_TRIM_EN BIT(0) |
| #define QPNP_IADC_EN_CTL1 0x46 |
| #define QPNP_IADC_ADC_EN BIT(7) |
| #define QPNP_ADC_CH_SEL_CTL 0x48 |
| #define QPNP_ADC_DIG_PARAM 0x50 |
| #define QPNP_ADC_CLK_SEL_MASK 0x3 |
| #define QPNP_ADC_DEC_RATIO_SEL_MASK 0xc |
| #define QPNP_ADC_DIG_DEC_RATIO_SEL_SHIFT 2 |
| |
| #define QPNP_HW_SETTLE_DELAY 0x51 |
| #define QPNP_CONV_REQ 0x52 |
| #define QPNP_CONV_REQ_SET BIT(7) |
| #define QPNP_CONV_SEQ_CTL 0x54 |
| #define QPNP_CONV_SEQ_HOLDOFF_SHIFT 4 |
| #define QPNP_CONV_SEQ_TRIG_CTL 0x55 |
| #define QPNP_FAST_AVG_CTL 0x5a |
| |
| #define QPNP_M0_LOW_THR_LSB 0x5c |
| #define QPNP_M0_LOW_THR_MSB 0x5d |
| #define QPNP_M0_HIGH_THR_LSB 0x5e |
| #define QPNP_M0_HIGH_THR_MSB 0x5f |
| #define QPNP_M1_LOW_THR_LSB 0x69 |
| #define QPNP_M1_LOW_THR_MSB 0x6a |
| #define QPNP_M1_HIGH_THR_LSB 0x6b |
| #define QPNP_M1_HIGH_THR_MSB 0x6c |
| |
| #define QPNP_DATA0 0x60 |
| #define QPNP_DATA1 0x61 |
| #define QPNP_CONV_TIMEOUT_ERR 2 |
| |
| #define QPNP_IADC_SEC_ACCESS 0xD0 |
| #define QPNP_IADC_SEC_ACCESS_DATA 0xA5 |
| #define QPNP_IADC_MSB_OFFSET 0xF2 |
| #define QPNP_IADC_LSB_OFFSET 0xF3 |
| #define QPNP_IADC_NOMINAL_RSENSE 0xF4 |
| #define QPNP_IADC_ATE_GAIN_CALIB_OFFSET 0xF5 |
| |
| #define QPNP_IADC_ADC_CH_SEL_CTL 0x48 |
| #define QPNP_IADC_ADC_CHX_SEL_SHIFT 3 |
| |
| #define QPNP_IADC_ADC_DIG_PARAM 0x50 |
| #define QPNP_IADC_CLK_SEL_SHIFT 1 |
| #define QPNP_IADC_DEC_RATIO_SEL 3 |
| |
| #define QPNP_IADC_CONV_REQUEST 0x52 |
| #define QPNP_IADC_CONV_REQ BIT(7) |
| |
| #define QPNP_IADC_DATA0 0x60 |
| #define QPNP_IADC_DATA1 0x61 |
| |
| #define QPNP_ADC_CONV_TIME_MIN 8000 |
| #define QPNP_ADC_CONV_TIME_MAX 8200 |
| |
| #define QPNP_ADC_GAIN_NV 17857 |
| #define QPNP_OFFSET_CALIBRATION_SHORT_CADC_LEADS_IDEAL 0 |
| #define QPNP_IADC_INTERNAL_RSENSE_N_OHMS_FACTOR 10000000 |
| #define QPNP_IADC_NANO_VOLTS_FACTOR 1000000000 |
| #define QPNP_IADC_CALIB_SECONDS 300000 |
| #define QPNP_IADC_RSENSE_LSB_N_OHMS_PER_BIT 15625 |
| #define QPNP_IADC_DIE_TEMP_CALIB_OFFSET 5000 |
| |
| #define QPNP_RAW_CODE_16_BIT_MSB_MASK 0xff00 |
| #define QPNP_RAW_CODE_16_BIT_LSB_MASK 0xff |
| #define QPNP_BIT_SHIFT_8 8 |
| #define QPNP_RSENSE_MSB_SIGN_CHECK 0x80 |
| |
| struct qpnp_iadc_drv { |
| struct qpnp_adc_drv *adc; |
| int32_t rsense; |
| struct device *iadc_hwmon; |
| bool iadc_init_calib; |
| bool iadc_initialized; |
| int64_t die_temp_calib_offset; |
| struct delayed_work iadc_work; |
| struct sensor_device_attribute sens_attr[0]; |
| }; |
| |
| struct qpnp_iadc_drv *qpnp_iadc; |
| |
| static int32_t qpnp_iadc_read_reg(uint32_t reg, u8 *data) |
| { |
| struct qpnp_iadc_drv *iadc = qpnp_iadc; |
| int rc; |
| |
| rc = spmi_ext_register_readl(iadc->adc->spmi->ctrl, iadc->adc->slave, |
| (iadc->adc->offset + reg), data, 1); |
| if (rc < 0) { |
| pr_err("qpnp iadc read reg %d failed with %d\n", reg, rc); |
| return rc; |
| } |
| |
| return 0; |
| } |
| |
| static int32_t qpnp_iadc_write_reg(uint32_t reg, u8 data) |
| { |
| struct qpnp_iadc_drv *iadc = qpnp_iadc; |
| int rc; |
| u8 *buf; |
| |
| buf = &data; |
| rc = spmi_ext_register_writel(iadc->adc->spmi->ctrl, iadc->adc->slave, |
| (iadc->adc->offset + reg), buf, 1); |
| if (rc < 0) { |
| pr_err("qpnp iadc write reg %d failed with %d\n", reg, rc); |
| return rc; |
| } |
| |
| return 0; |
| } |
| |
| static int32_t qpnp_iadc_configure_interrupt(void) |
| { |
| int rc = 0; |
| u8 data = 0; |
| |
| /* Configure interrupt as an Edge trigger */ |
| rc = qpnp_iadc_write_reg(QPNP_INT_SET_TYPE, |
| QPNP_INT_CLR_MASK); |
| if (rc < 0) { |
| pr_err("%s Interrupt configure failed\n", __func__); |
| return rc; |
| } |
| |
| /* Configure interrupt for rising edge trigger */ |
| rc = qpnp_iadc_write_reg(QPNP_INT_POLARITY_HIGH, |
| QPNP_INT_CLR_MASK); |
| if (rc < 0) { |
| pr_err("%s Rising edge trigger configure failed\n", __func__); |
| return rc; |
| } |
| |
| /* Disable low level interrupt triggering */ |
| data = QPNP_INT_CLR_MASK; |
| rc = qpnp_iadc_write_reg(QPNP_INT_POLARITY_LOW, |
| (~data & QPNP_INT_CLR_MASK)); |
| if (rc < 0) { |
| pr_err("%s Setting level low to disable failed\n", __func__); |
| return rc; |
| } |
| |
| return 0; |
| } |
| |
| static void trigger_iadc_completion(struct work_struct *work) |
| { |
| struct qpnp_iadc_drv *iadc = qpnp_iadc; |
| int rc; |
| |
| rc = qpnp_iadc_write_reg(QPNP_INT_CLR, QPNP_INT_CLR_MASK); |
| if (rc < 0) |
| pr_err("qpnp iadc interrupt mask failed with %d\n", rc); |
| |
| complete(&iadc->adc->adc_rslt_completion); |
| |
| return; |
| } |
| DECLARE_WORK(trigger_iadc_completion_work, trigger_iadc_completion); |
| |
| static irqreturn_t qpnp_iadc_isr(int irq, void *dev_id) |
| { |
| schedule_work(&trigger_iadc_completion_work); |
| |
| return IRQ_HANDLED; |
| } |
| |
| static int32_t qpnp_iadc_enable(bool state) |
| { |
| int rc = 0; |
| u8 data = 0; |
| |
| data = QPNP_IADC_ADC_EN; |
| if (state) { |
| rc = qpnp_iadc_write_reg(QPNP_IADC_EN_CTL1, |
| data); |
| if (rc < 0) { |
| pr_err("IADC enable failed\n"); |
| return rc; |
| } |
| } else { |
| rc = qpnp_iadc_write_reg(QPNP_IADC_EN_CTL1, |
| (~data & QPNP_IADC_ADC_EN)); |
| if (rc < 0) { |
| pr_err("IADC disable failed\n"); |
| return rc; |
| } |
| } |
| |
| return 0; |
| } |
| |
| static int32_t qpnp_iadc_read_conversion_result(uint16_t *data) |
| { |
| uint8_t rslt_lsb, rslt_msb; |
| uint16_t rslt; |
| int32_t rc; |
| |
| rc = qpnp_iadc_read_reg(QPNP_IADC_DATA0, &rslt_lsb); |
| if (rc < 0) { |
| pr_err("qpnp adc result read failed with %d\n", rc); |
| return rc; |
| } |
| |
| rc = qpnp_iadc_read_reg(QPNP_IADC_DATA1, &rslt_msb); |
| if (rc < 0) { |
| pr_err("qpnp adc result read failed with %d\n", rc); |
| return rc; |
| } |
| |
| rslt = (rslt_msb << 8) | rslt_lsb; |
| *data = rslt; |
| |
| rc = qpnp_iadc_enable(false); |
| if (rc) |
| return rc; |
| |
| return 0; |
| } |
| |
| static int32_t qpnp_iadc_configure(enum qpnp_iadc_channels channel, |
| uint16_t *raw_code) |
| { |
| struct qpnp_iadc_drv *iadc = qpnp_iadc; |
| u8 qpnp_iadc_mode_reg = 0, qpnp_iadc_ch_sel_reg = 0; |
| u8 qpnp_iadc_conv_req = 0, qpnp_iadc_dig_param_reg = 0; |
| int32_t rc = 0; |
| |
| qpnp_iadc_ch_sel_reg = channel; |
| |
| qpnp_iadc_dig_param_reg |= iadc->adc->amux_prop->decimation << |
| QPNP_IADC_DEC_RATIO_SEL; |
| |
| qpnp_iadc_conv_req = QPNP_IADC_CONV_REQ; |
| |
| rc = qpnp_iadc_write_reg(QPNP_INT_EN_SET, |
| QPNP_INT_EN_SET_EOC_INT_EN_SET); |
| if (rc < 0) { |
| pr_err("qpnp adc configure error for interrupt setup\n"); |
| return rc; |
| } |
| |
| rc = qpnp_iadc_write_reg(QPNP_IADC_MODE_CTL, qpnp_iadc_mode_reg); |
| if (rc) { |
| pr_err("qpnp adc read adc failed with %d\n", rc); |
| return rc; |
| } |
| |
| rc = qpnp_iadc_write_reg(QPNP_IADC_ADC_CH_SEL_CTL, |
| qpnp_iadc_ch_sel_reg); |
| if (rc) { |
| pr_err("qpnp adc read adc failed with %d\n", rc); |
| return rc; |
| } |
| |
| rc = qpnp_iadc_write_reg(QPNP_ADC_DIG_PARAM, |
| qpnp_iadc_dig_param_reg); |
| if (rc) { |
| pr_err("qpnp adc read adc failed with %d\n", rc); |
| return rc; |
| } |
| |
| rc = qpnp_iadc_write_reg(QPNP_HW_SETTLE_DELAY, |
| iadc->adc->amux_prop->hw_settle_time); |
| if (rc < 0) { |
| pr_err("qpnp adc configure error for hw settling time setup\n"); |
| return rc; |
| } |
| |
| rc = qpnp_iadc_write_reg(QPNP_FAST_AVG_CTL, |
| iadc->adc->amux_prop->fast_avg_setup); |
| if (rc < 0) { |
| pr_err("qpnp adc fast averaging configure error\n"); |
| return rc; |
| } |
| |
| rc = qpnp_iadc_enable(true); |
| if (rc) |
| return rc; |
| |
| rc = qpnp_iadc_write_reg(QPNP_CONV_REQ, qpnp_iadc_conv_req); |
| if (rc) { |
| pr_err("qpnp adc read adc failed with %d\n", rc); |
| return rc; |
| } |
| |
| wait_for_completion(&iadc->adc->adc_rslt_completion); |
| |
| rc = qpnp_iadc_read_conversion_result(raw_code); |
| if (rc) { |
| pr_err("qpnp adc read adc failed with %d\n", rc); |
| return rc; |
| } |
| |
| return 0; |
| } |
| |
| static int32_t qpnp_convert_raw_offset_voltage(void) |
| { |
| struct qpnp_iadc_drv *iadc = qpnp_iadc; |
| uint32_t num = 0; |
| |
| num = iadc->adc->calib.offset_raw - iadc->adc->calib.offset_raw; |
| |
| iadc->adc->calib.offset_uv = (num * QPNP_ADC_GAIN_NV)/ |
| (iadc->adc->calib.gain_raw - iadc->adc->calib.offset_raw); |
| |
| num = iadc->adc->calib.gain_raw - iadc->adc->calib.offset_raw; |
| |
| iadc->adc->calib.gain_uv = (num * QPNP_ADC_GAIN_NV)/ |
| (iadc->adc->calib.gain_raw - iadc->adc->calib.offset_raw); |
| |
| return 0; |
| } |
| |
| static int32_t qpnp_iadc_calibrate_for_trim(void) |
| { |
| struct qpnp_iadc_drv *iadc = qpnp_iadc; |
| uint8_t rslt_lsb, rslt_msb; |
| int32_t rc = 0; |
| uint16_t raw_data; |
| |
| rc = qpnp_iadc_configure(GAIN_CALIBRATION_17P857MV, &raw_data); |
| if (rc < 0) { |
| pr_err("qpnp adc result read failed with %d\n", rc); |
| goto fail; |
| } |
| |
| iadc->adc->calib.gain_raw = raw_data; |
| |
| rc = qpnp_iadc_configure(OFFSET_CALIBRATION_SHORT_CADC_LEADS, |
| &raw_data); |
| if (rc < 0) { |
| pr_err("qpnp adc result read failed with %d\n", rc); |
| goto fail; |
| } |
| |
| iadc->adc->calib.offset_raw = raw_data; |
| if (rc < 0) { |
| pr_err("qpnp adc offset/gain calculation failed\n"); |
| goto fail; |
| } |
| |
| rc = qpnp_convert_raw_offset_voltage(); |
| |
| rslt_msb = (raw_data & QPNP_RAW_CODE_16_BIT_MSB_MASK) >> |
| QPNP_BIT_SHIFT_8; |
| rslt_lsb = raw_data & QPNP_RAW_CODE_16_BIT_LSB_MASK; |
| |
| rc = qpnp_iadc_write_reg(QPNP_IADC_SEC_ACCESS, |
| QPNP_IADC_SEC_ACCESS_DATA); |
| if (rc < 0) { |
| pr_err("qpnp iadc configure error for sec access\n"); |
| goto fail; |
| } |
| |
| rc = qpnp_iadc_write_reg(QPNP_IADC_MSB_OFFSET, |
| rslt_msb); |
| if (rc < 0) { |
| pr_err("qpnp iadc configure error for MSB write\n"); |
| goto fail; |
| } |
| |
| rc = qpnp_iadc_write_reg(QPNP_IADC_SEC_ACCESS, |
| QPNP_IADC_SEC_ACCESS_DATA); |
| if (rc < 0) { |
| pr_err("qpnp iadc configure error for sec access\n"); |
| goto fail; |
| } |
| |
| rc = qpnp_iadc_write_reg(QPNP_IADC_LSB_OFFSET, |
| rslt_lsb); |
| if (rc < 0) { |
| pr_err("qpnp iadc configure error for LSB write\n"); |
| goto fail; |
| } |
| fail: |
| return rc; |
| } |
| |
| static void qpnp_iadc_work(struct work_struct *work) |
| { |
| struct qpnp_iadc_drv *iadc = qpnp_iadc; |
| int rc = 0; |
| |
| mutex_lock(&iadc->adc->adc_lock); |
| |
| rc = qpnp_iadc_calibrate_for_trim(); |
| if (rc) |
| pr_err("periodic IADC calibration failed\n"); |
| |
| mutex_unlock(&iadc->adc->adc_lock); |
| |
| schedule_delayed_work(&iadc->iadc_work, |
| round_jiffies_relative(msecs_to_jiffies |
| (QPNP_IADC_CALIB_SECONDS))); |
| |
| return; |
| } |
| |
| static int32_t qpnp_iadc_version_check(void) |
| { |
| uint8_t revision; |
| int rc; |
| |
| rc = qpnp_iadc_read_reg(QPNP_IADC_REVISION2, &revision); |
| if (rc < 0) { |
| pr_err("qpnp adc result read failed with %d\n", rc); |
| return rc; |
| } |
| |
| if (revision < QPNP_IADC_SUPPORTED_REVISION2) { |
| pr_err("IADC Version not supported\n"); |
| return -EINVAL; |
| } |
| |
| return 0; |
| } |
| |
| int32_t qpnp_iadc_is_ready(void) |
| { |
| struct qpnp_iadc_drv *iadc = qpnp_iadc; |
| |
| if (!iadc || !iadc->iadc_initialized) |
| return -EPROBE_DEFER; |
| else |
| return 0; |
| } |
| EXPORT_SYMBOL(qpnp_iadc_is_ready); |
| |
| int32_t qpnp_iadc_get_rsense(int32_t *rsense) |
| { |
| uint8_t rslt_rsense; |
| int32_t rc, sign_bit = 0; |
| |
| rc = qpnp_iadc_read_reg(QPNP_IADC_NOMINAL_RSENSE, &rslt_rsense); |
| if (rc < 0) { |
| pr_err("qpnp adc rsense read failed with %d\n", rc); |
| return rc; |
| } |
| |
| if (rslt_rsense & QPNP_RSENSE_MSB_SIGN_CHECK) |
| sign_bit = 1; |
| |
| rslt_rsense &= ~QPNP_RSENSE_MSB_SIGN_CHECK; |
| |
| if (sign_bit) |
| *rsense = QPNP_IADC_INTERNAL_RSENSE_N_OHMS_FACTOR - |
| (rslt_rsense * QPNP_IADC_RSENSE_LSB_N_OHMS_PER_BIT); |
| else |
| *rsense = QPNP_IADC_INTERNAL_RSENSE_N_OHMS_FACTOR + |
| (rslt_rsense * QPNP_IADC_RSENSE_LSB_N_OHMS_PER_BIT); |
| |
| return rc; |
| } |
| |
| int32_t qpnp_check_pmic_temp(void) |
| { |
| struct qpnp_iadc_drv *iadc = qpnp_iadc; |
| struct qpnp_vadc_result result_pmic_therm; |
| int rc; |
| |
| rc = qpnp_vadc_read(DIE_TEMP, &result_pmic_therm); |
| if (rc < 0) |
| return rc; |
| |
| if (((uint64_t) (result_pmic_therm.physical - |
| iadc->die_temp_calib_offset)) |
| > QPNP_IADC_DIE_TEMP_CALIB_OFFSET) { |
| mutex_lock(&iadc->adc->adc_lock); |
| |
| rc = qpnp_iadc_calibrate_for_trim(); |
| if (rc) |
| pr_err("periodic IADC calibration failed\n"); |
| |
| mutex_unlock(&iadc->adc->adc_lock); |
| } |
| |
| return 0; |
| } |
| |
| int32_t qpnp_iadc_read(enum qpnp_iadc_channels channel, |
| struct qpnp_iadc_result *result) |
| { |
| struct qpnp_iadc_drv *iadc = qpnp_iadc; |
| int32_t rc, rsense_n_ohms, sign = 0, num; |
| int64_t result_current; |
| uint16_t raw_data; |
| |
| if (!iadc || !iadc->iadc_initialized) |
| return -EPROBE_DEFER; |
| |
| rc = qpnp_check_pmic_temp(); |
| if (rc) { |
| pr_err("Error checking pmic therm temp\n"); |
| return rc; |
| } |
| |
| mutex_lock(&iadc->adc->adc_lock); |
| |
| rc = qpnp_iadc_configure(channel, &raw_data); |
| if (rc < 0) { |
| pr_err("qpnp adc result read failed with %d\n", rc); |
| goto fail; |
| } |
| |
| rc = qpnp_iadc_get_rsense(&rsense_n_ohms); |
| |
| num = raw_data - iadc->adc->calib.offset_raw; |
| if (num < 0) { |
| sign = 1; |
| num = -num; |
| } |
| |
| result->result_uv = (num * QPNP_ADC_GAIN_NV)/ |
| (iadc->adc->calib.gain_raw - iadc->adc->calib.offset_raw); |
| result_current = result->result_uv; |
| result_current *= QPNP_IADC_NANO_VOLTS_FACTOR; |
| do_div(result_current, rsense_n_ohms); |
| |
| if (sign) { |
| result->result_uv = -result->result_uv; |
| result_current = -result_current; |
| } |
| |
| result->result_ua = (int32_t) result_current; |
| fail: |
| mutex_unlock(&iadc->adc->adc_lock); |
| |
| return rc; |
| } |
| EXPORT_SYMBOL(qpnp_iadc_read); |
| |
| int32_t qpnp_iadc_get_gain_and_offset(struct qpnp_iadc_calib *result) |
| { |
| struct qpnp_iadc_drv *iadc = qpnp_iadc; |
| int rc; |
| |
| if (!iadc || !iadc->iadc_initialized) |
| return -EPROBE_DEFER; |
| |
| rc = qpnp_check_pmic_temp(); |
| if (rc) { |
| pr_err("Error checking pmic therm temp\n"); |
| return rc; |
| } |
| |
| mutex_lock(&iadc->adc->adc_lock); |
| result->gain_raw = iadc->adc->calib.gain_raw; |
| result->ideal_gain_nv = QPNP_ADC_GAIN_NV; |
| result->gain_uv = iadc->adc->calib.gain_uv; |
| result->offset_raw = iadc->adc->calib.offset_raw; |
| result->ideal_offset_uv = |
| QPNP_OFFSET_CALIBRATION_SHORT_CADC_LEADS_IDEAL; |
| result->offset_uv = iadc->adc->calib.offset_uv; |
| mutex_unlock(&iadc->adc->adc_lock); |
| |
| return 0; |
| } |
| EXPORT_SYMBOL(qpnp_iadc_get_gain_and_offset); |
| |
| static ssize_t qpnp_iadc_show(struct device *dev, |
| struct device_attribute *devattr, char *buf) |
| { |
| struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr); |
| struct qpnp_iadc_result result; |
| int rc = -1; |
| |
| rc = qpnp_iadc_read(attr->index, &result); |
| |
| if (rc) |
| return 0; |
| |
| return snprintf(buf, QPNP_ADC_HWMON_NAME_LENGTH, |
| "Result:%d\n", result.result_ua); |
| } |
| |
| static struct sensor_device_attribute qpnp_adc_attr = |
| SENSOR_ATTR(NULL, S_IRUGO, qpnp_iadc_show, NULL, 0); |
| |
| static int32_t qpnp_iadc_init_hwmon(struct spmi_device *spmi) |
| { |
| struct qpnp_iadc_drv *iadc = qpnp_iadc; |
| struct device_node *child; |
| struct device_node *node = spmi->dev.of_node; |
| int rc = 0, i = 0, channel; |
| |
| for_each_child_of_node(node, child) { |
| channel = iadc->adc->adc_channels[i].channel_num; |
| qpnp_adc_attr.index = iadc->adc->adc_channels[i].channel_num; |
| qpnp_adc_attr.dev_attr.attr.name = |
| iadc->adc->adc_channels[i].name; |
| sysfs_attr_init(&iadc->sens_attr[i].dev_attr.attr); |
| memcpy(&iadc->sens_attr[i], &qpnp_adc_attr, |
| sizeof(qpnp_adc_attr)); |
| rc = device_create_file(&spmi->dev, |
| &iadc->sens_attr[i].dev_attr); |
| if (rc) { |
| dev_err(&spmi->dev, |
| "device_create_file failed for dev %s\n", |
| iadc->adc->adc_channels[i].name); |
| goto hwmon_err_sens; |
| } |
| i++; |
| } |
| |
| return 0; |
| hwmon_err_sens: |
| pr_err("Init HWMON failed for qpnp_iadc with %d\n", rc); |
| return rc; |
| } |
| |
| static int __devinit qpnp_iadc_probe(struct spmi_device *spmi) |
| { |
| struct qpnp_iadc_drv *iadc; |
| struct qpnp_adc_drv *adc_qpnp; |
| struct device_node *node = spmi->dev.of_node; |
| struct device_node *child; |
| int rc, count_adc_channel_list = 0; |
| |
| if (!node) |
| return -EINVAL; |
| |
| if (qpnp_iadc) { |
| pr_err("IADC already in use\n"); |
| return -EBUSY; |
| } |
| |
| for_each_child_of_node(node, child) |
| count_adc_channel_list++; |
| |
| if (!count_adc_channel_list) { |
| pr_err("No channel listing\n"); |
| return -EINVAL; |
| } |
| |
| iadc = devm_kzalloc(&spmi->dev, sizeof(struct qpnp_iadc_drv) + |
| (sizeof(struct sensor_device_attribute) * |
| count_adc_channel_list), GFP_KERNEL); |
| if (!iadc) { |
| dev_err(&spmi->dev, "Unable to allocate memory\n"); |
| return -ENOMEM; |
| } |
| |
| adc_qpnp = devm_kzalloc(&spmi->dev, sizeof(struct qpnp_adc_drv), |
| GFP_KERNEL); |
| if (!adc_qpnp) { |
| dev_err(&spmi->dev, "Unable to allocate memory\n"); |
| return -ENOMEM; |
| } |
| |
| iadc->adc = adc_qpnp; |
| |
| rc = qpnp_adc_get_devicetree_data(spmi, iadc->adc); |
| if (rc) { |
| dev_err(&spmi->dev, "failed to read device tree\n"); |
| return rc; |
| } |
| |
| rc = of_property_read_u32(node, "qcom,rsense", |
| &iadc->rsense); |
| if (rc) { |
| pr_err("Invalid rsens reference property\n"); |
| return -EINVAL; |
| } |
| |
| rc = devm_request_irq(&spmi->dev, iadc->adc->adc_irq, |
| qpnp_iadc_isr, |
| IRQF_TRIGGER_RISING, "qpnp_iadc_interrupt", iadc); |
| if (rc) { |
| dev_err(&spmi->dev, "failed to request adc irq\n"); |
| return rc; |
| } else |
| enable_irq_wake(iadc->adc->adc_irq); |
| |
| iadc->iadc_init_calib = false; |
| dev_set_drvdata(&spmi->dev, iadc); |
| qpnp_iadc = iadc; |
| |
| rc = qpnp_iadc_init_hwmon(spmi); |
| if (rc) { |
| dev_err(&spmi->dev, "failed to initialize qpnp hwmon adc\n"); |
| return rc; |
| } |
| iadc->iadc_hwmon = hwmon_device_register(&iadc->adc->spmi->dev); |
| |
| rc = qpnp_iadc_configure_interrupt(); |
| if (rc) { |
| dev_err(&spmi->dev, "failed to configure interrupt\n"); |
| return rc; |
| } |
| |
| rc = qpnp_iadc_version_check(); |
| if (rc) { |
| dev_err(&spmi->dev, "IADC version not supported\n"); |
| return rc; |
| } |
| |
| rc = qpnp_iadc_calibrate_for_trim(); |
| if (rc) { |
| dev_err(&spmi->dev, "failed to calibrate for USR trim\n"); |
| return rc; |
| } |
| iadc->iadc_init_calib = true; |
| INIT_DELAYED_WORK(&iadc->iadc_work, qpnp_iadc_work); |
| schedule_delayed_work(&iadc->iadc_work, |
| round_jiffies_relative(msecs_to_jiffies |
| (QPNP_IADC_CALIB_SECONDS))); |
| iadc->iadc_initialized = true; |
| |
| return 0; |
| } |
| |
| static int __devexit qpnp_iadc_remove(struct spmi_device *spmi) |
| { |
| struct qpnp_iadc_drv *iadc = dev_get_drvdata(&spmi->dev); |
| struct device_node *node = spmi->dev.of_node; |
| struct device_node *child; |
| int i = 0; |
| |
| for_each_child_of_node(node, child) { |
| device_remove_file(&spmi->dev, |
| &iadc->sens_attr[i].dev_attr); |
| i++; |
| } |
| dev_set_drvdata(&spmi->dev, NULL); |
| |
| return 0; |
| } |
| |
| static const struct of_device_id qpnp_iadc_match_table[] = { |
| { .compatible = "qcom,qpnp-iadc", |
| }, |
| {} |
| }; |
| |
| static struct spmi_driver qpnp_iadc_driver = { |
| .driver = { |
| .name = "qcom,qpnp-iadc", |
| .of_match_table = qpnp_iadc_match_table, |
| }, |
| .probe = qpnp_iadc_probe, |
| .remove = qpnp_iadc_remove, |
| }; |
| |
| static int __init qpnp_iadc_init(void) |
| { |
| return spmi_driver_register(&qpnp_iadc_driver); |
| } |
| module_init(qpnp_iadc_init); |
| |
| static void __exit qpnp_iadc_exit(void) |
| { |
| spmi_driver_unregister(&qpnp_iadc_driver); |
| } |
| module_exit(qpnp_iadc_exit); |
| |
| MODULE_DESCRIPTION("QPNP PMIC current ADC driver"); |
| MODULE_LICENSE("GPL v2"); |