arch/ppc/syslib/ppc4xx_dma.c - kernel/msm - Gitiles

 /*
  * IBM PPC4xx DMA engine core library
  *
  * Copyright 2000-2004 MontaVista Software Inc.
  *
  * Cleaned up and converted to new DCR access
  * Matt Porter <mporter@kernel.crashing.org>
  *
  * Original code by Armin Kuster <akuster@mvista.com>
  * and Pete Popov <ppopov@mvista.com>
  *
  * This program is free software; you can redistribute  it and/or modify it
  * under  the terms of  the GNU General  Public License as published by the
  * Free Software Foundation;  either version 2 of the  License, or (at your
  * option) any later version.
  *
  * You should have received a copy of the  GNU General Public License along
  * with this program; if not, write  to the Free Software Foundation, Inc.,
  * 675 Mass Ave, Cambridge, MA 02139, USA.
  */

 #include <linux/kernel.h>
 #include <linux/mm.h>
 #include <linux/miscdevice.h>
 #include <linux/init.h>
 #include <linux/module.h>

 #include <asm/system.h>
 #include <asm/io.h>
 #include <asm/dma.h>
 #include <asm/ppc4xx_dma.h>

 ppc_dma_ch_t dma_channels[MAX_PPC4xx_DMA_CHANNELS];

 int
 ppc4xx_get_dma_status(void)
 {
 	return (mfdcr(DCRN_DMASR));
 }

 void
 ppc4xx_set_src_addr(int dmanr, phys_addr_t src_addr)
 {
 	if (dmanr >= MAX_PPC4xx_DMA_CHANNELS) {
 		printk("set_src_addr: bad channel: %d\n", dmanr);
 		return;
 	}

 #ifdef PPC4xx_DMA_64BIT
 	mtdcr(DCRN_DMASAH0 + dmanr*2, (u32)(src_addr >> 32));
 #else
 	mtdcr(DCRN_DMASA0 + dmanr*2, (u32)src_addr);
 #endif
 }

 void
 ppc4xx_set_dst_addr(int dmanr, phys_addr_t dst_addr)
 {
 	if (dmanr >= MAX_PPC4xx_DMA_CHANNELS) {
 		printk("set_dst_addr: bad channel: %d\n", dmanr);
 		return;
 	}

 #ifdef PPC4xx_DMA_64BIT
 	mtdcr(DCRN_DMADAH0 + dmanr*2, (u32)(dst_addr >> 32));
 #else
 	mtdcr(DCRN_DMADA0 + dmanr*2, (u32)dst_addr);
 #endif
 }

 void
 ppc4xx_enable_dma(unsigned int dmanr)
 {
 	unsigned int control;
 	ppc_dma_ch_t *p_dma_ch = &dma_channels[dmanr];
 	unsigned int status_bits[] = { DMA_CS0 | DMA_TS0 | DMA_CH0_ERR,
 				       DMA_CS1 | DMA_TS1 | DMA_CH1_ERR,
 				       DMA_CS2 | DMA_TS2 | DMA_CH2_ERR,
 				       DMA_CS3 | DMA_TS3 | DMA_CH3_ERR};

 	if (p_dma_ch->in_use) {
 		printk("enable_dma: channel %d in use\n", dmanr);
 		return;
 	}

 	if (dmanr >= MAX_PPC4xx_DMA_CHANNELS) {
 		printk("enable_dma: bad channel: %d\n", dmanr);
 		return;
 	}

 	if (p_dma_ch->mode == DMA_MODE_READ) {
 		/* peripheral to memory */
 		ppc4xx_set_src_addr(dmanr, 0);
 		ppc4xx_set_dst_addr(dmanr, p_dma_ch->addr);
 	} else if (p_dma_ch->mode == DMA_MODE_WRITE) {
 		/* memory to peripheral */
 		ppc4xx_set_src_addr(dmanr, p_dma_ch->addr);
 		ppc4xx_set_dst_addr(dmanr, 0);
 	}

 	/* for other xfer modes, the addresses are already set */
 	control = mfdcr(DCRN_DMACR0 + (dmanr * 0x8));

 	control &= ~(DMA_TM_MASK | DMA_TD);	/* clear all mode bits */
 	if (p_dma_ch->mode == DMA_MODE_MM) {
 		/* software initiated memory to memory */
 		control |= DMA_ETD_OUTPUT | DMA_TCE_ENABLE;
 	}

 	mtdcr(DCRN_DMACR0 + (dmanr * 0x8), control);

 	/*
 	 * Clear the CS, TS, RI bits for the channel from DMASR.  This
 	 * has been observed to happen correctly only after the mode and
 	 * ETD/DCE bits in DMACRx are set above.  Must do this before
 	 * enabling the channel.
 	 */

 	mtdcr(DCRN_DMASR, status_bits[dmanr]);

 	/*
 	 * For device-paced transfers, Terminal Count Enable apparently
 	 * must be on, and this must be turned on after the mode, etc.
 	 * bits are cleared above (at least on Redwood-6).
 	 */

 	if ((p_dma_ch->mode == DMA_MODE_MM_DEVATDST) ||
 	    (p_dma_ch->mode == DMA_MODE_MM_DEVATSRC))
 		control |= DMA_TCE_ENABLE;

 	/*
 	 * Now enable the channel.
 	 */

 	control |= (p_dma_ch->mode | DMA_CE_ENABLE);

 	mtdcr(DCRN_DMACR0 + (dmanr * 0x8), control);

 	p_dma_ch->in_use = 1;
 }

 void
 ppc4xx_disable_dma(unsigned int dmanr)
 {
 	unsigned int control;
 	ppc_dma_ch_t *p_dma_ch = &dma_channels[dmanr];

 	if (!p_dma_ch->in_use) {
 		printk("disable_dma: channel %d not in use\n", dmanr);
 		return;
 	}

 	if (dmanr >= MAX_PPC4xx_DMA_CHANNELS) {
 		printk("disable_dma: bad channel: %d\n", dmanr);
 		return;
 	}

 	control = mfdcr(DCRN_DMACR0 + (dmanr * 0x8));
 	control &= ~DMA_CE_ENABLE;
 	mtdcr(DCRN_DMACR0 + (dmanr * 0x8), control);

 	p_dma_ch->in_use = 0;
 }

 /*
  * Sets the dma mode for single DMA transfers only.
  * For scatter/gather transfers, the mode is passed to the
  * alloc_dma_handle() function as one of the parameters.
  *
  * The mode is simply saved and used later.  This allows
  * the driver to call set_dma_mode() and set_dma_addr() in
  * any order.
  *
  * Valid mode values are:
  *
  * DMA_MODE_READ          peripheral to memory
  * DMA_MODE_WRITE         memory to peripheral
  * DMA_MODE_MM            memory to memory
  * DMA_MODE_MM_DEVATSRC   device-paced memory to memory, device at src
  * DMA_MODE_MM_DEVATDST   device-paced memory to memory, device at dst
  */
 int
 ppc4xx_set_dma_mode(unsigned int dmanr, unsigned int mode)
 {
 	ppc_dma_ch_t *p_dma_ch = &dma_channels[dmanr];

 	if (dmanr >= MAX_PPC4xx_DMA_CHANNELS) {
 		printk("set_dma_mode: bad channel 0x%x\n", dmanr);
 		return DMA_STATUS_BAD_CHANNEL;
 	}

 	p_dma_ch->mode = mode;

 	return DMA_STATUS_GOOD;
 }

 /*
  * Sets the DMA Count register. Note that 'count' is in bytes.
  * However, the DMA Count register counts the number of "transfers",
  * where each transfer is equal to the bus width.  Thus, count
  * MUST be a multiple of the bus width.
  */
 void
 ppc4xx_set_dma_count(unsigned int dmanr, unsigned int count)
 {
 	ppc_dma_ch_t *p_dma_ch = &dma_channels[dmanr];

 #ifdef DEBUG_4xxDMA
 	{
 		int error = 0;
 		switch (p_dma_ch->pwidth) {
 		case PW_8:
 			break;
 		case PW_16:
 			if (count & 0x1)
 				error = 1;
 			break;
 		case PW_32:
 			if (count & 0x3)
 				error = 1;
 			break;
 		case PW_64:
 			if (count & 0x7)
 				error = 1;
 			break;
 		default:
 			printk("set_dma_count: invalid bus width: 0x%x\n",
 			       p_dma_ch->pwidth);
 			return;
 		}
 		if (error)
 			printk
 			    ("Warning: set_dma_count count 0x%x bus width %d\n",
 			     count, p_dma_ch->pwidth);
 	}
 #endif

 	count = count >> p_dma_ch->shift;

 	mtdcr(DCRN_DMACT0 + (dmanr * 0x8), count);
 }

 /*
  *   Returns the number of bytes left to be transferred.
  *   After a DMA transfer, this should return zero.
  *   Reading this while a DMA transfer is still in progress will return
  *   unpredictable results.
  */
 int
 ppc4xx_get_dma_residue(unsigned int dmanr)
 {
 	unsigned int count;
 	ppc_dma_ch_t *p_dma_ch = &dma_channels[dmanr];

 	if (dmanr >= MAX_PPC4xx_DMA_CHANNELS) {
 		printk("ppc4xx_get_dma_residue: bad channel 0x%x\n", dmanr);
 		return DMA_STATUS_BAD_CHANNEL;
 	}

 	count = mfdcr(DCRN_DMACT0 + (dmanr * 0x8));

 	return (count << p_dma_ch->shift);
 }

 /*
  * Sets the DMA address for a memory to peripheral or peripheral
  * to memory transfer.  The address is just saved in the channel
  * structure for now and used later in enable_dma().
  */
 void
 ppc4xx_set_dma_addr(unsigned int dmanr, phys_addr_t addr)
 {
 	ppc_dma_ch_t *p_dma_ch = &dma_channels[dmanr];

 	if (dmanr >= MAX_PPC4xx_DMA_CHANNELS) {
 		printk("ppc4xx_set_dma_addr: bad channel: %d\n", dmanr);
 		return;
 	}

 #ifdef DEBUG_4xxDMA
 	{
 		int error = 0;
 		switch (p_dma_ch->pwidth) {
 		case PW_8:
 			break;
 		case PW_16:
 			if ((unsigned) addr & 0x1)
 				error = 1;
 			break;
 		case PW_32:
 			if ((unsigned) addr & 0x3)
 				error = 1;
 			break;
 		case PW_64:
 			if ((unsigned) addr & 0x7)
 				error = 1;
 			break;
 		default:
 			printk("ppc4xx_set_dma_addr: invalid bus width: 0x%x\n",
 			       p_dma_ch->pwidth);
 			return;
 		}
 		if (error)
 			printk("Warning: ppc4xx_set_dma_addr addr 0x%x bus width %d\n",
 			       addr, p_dma_ch->pwidth);
 	}
 #endif

 	/* save dma address and program it later after we know the xfer mode */
 	p_dma_ch->addr = addr;
 }

 /*
  * Sets both DMA addresses for a memory to memory transfer.
  * For memory to peripheral or peripheral to memory transfers
  * the function set_dma_addr() should be used instead.
  */
 void
 ppc4xx_set_dma_addr2(unsigned int dmanr, phys_addr_t src_dma_addr,
 		     phys_addr_t dst_dma_addr)
 {
 	if (dmanr >= MAX_PPC4xx_DMA_CHANNELS) {
 		printk("ppc4xx_set_dma_addr2: bad channel: %d\n", dmanr);
 		return;
 	}

 #ifdef DEBUG_4xxDMA
 	{
 		ppc_dma_ch_t *p_dma_ch = &dma_channels[dmanr];
 		int error = 0;
 		switch (p_dma_ch->pwidth) {
 			case PW_8:
 				break;
 			case PW_16:
 				if (((unsigned) src_dma_addr & 0x1) ||
 						((unsigned) dst_dma_addr & 0x1)
 				   )
 					error = 1;
 				break;
 			case PW_32:
 				if (((unsigned) src_dma_addr & 0x3) ||
 						((unsigned) dst_dma_addr & 0x3)
 				   )
 					error = 1;
 				break;
 			case PW_64:
 				if (((unsigned) src_dma_addr & 0x7) ||
 						((unsigned) dst_dma_addr & 0x7)
 				   )
 					error = 1;
 				break;
 			default:
 				printk("ppc4xx_set_dma_addr2: invalid bus width: 0x%x\n",
 						p_dma_ch->pwidth);
 				return;
 		}
 		if (error)
 			printk
 				("Warning: ppc4xx_set_dma_addr2 src 0x%x dst 0x%x bus width %d\n",
 				 src_dma_addr, dst_dma_addr, p_dma_ch->pwidth);
 	}
 #endif

 	ppc4xx_set_src_addr(dmanr, src_dma_addr);
 	ppc4xx_set_dst_addr(dmanr, dst_dma_addr);
 }

 /*
  * Enables the channel interrupt.
  *
  * If performing a scatter/gatter transfer, this function
  * MUST be called before calling alloc_dma_handle() and building
  * the sgl list.  Otherwise, interrupts will not be enabled, if
  * they were previously disabled.
  */
 int
 ppc4xx_enable_dma_interrupt(unsigned int dmanr)
 {
 	unsigned int control;
 	ppc_dma_ch_t *p_dma_ch = &dma_channels[dmanr];

 	if (dmanr >= MAX_PPC4xx_DMA_CHANNELS) {
 		printk("ppc4xx_enable_dma_interrupt: bad channel: %d\n", dmanr);
 		return DMA_STATUS_BAD_CHANNEL;
 	}

 	p_dma_ch->int_enable = 1;

 	control = mfdcr(DCRN_DMACR0 + (dmanr * 0x8));
 	control |= DMA_CIE_ENABLE;	/* Channel Interrupt Enable */
 	mtdcr(DCRN_DMACR0 + (dmanr * 0x8), control);

 	return DMA_STATUS_GOOD;
 }

 /*
  * Disables the channel interrupt.
  *
  * If performing a scatter/gatter transfer, this function
  * MUST be called before calling alloc_dma_handle() and building
  * the sgl list.  Otherwise, interrupts will not be disabled, if
  * they were previously enabled.
  */
 int
 ppc4xx_disable_dma_interrupt(unsigned int dmanr)
 {
 	unsigned int control;
 	ppc_dma_ch_t *p_dma_ch = &dma_channels[dmanr];

 	if (dmanr >= MAX_PPC4xx_DMA_CHANNELS) {
 		printk("ppc4xx_disable_dma_interrupt: bad channel: %d\n", dmanr);
 		return DMA_STATUS_BAD_CHANNEL;
 	}

 	p_dma_ch->int_enable = 0;

 	control = mfdcr(DCRN_DMACR0 + (dmanr * 0x8));
 	control &= ~DMA_CIE_ENABLE;	/* Channel Interrupt Enable */
 	mtdcr(DCRN_DMACR0 + (dmanr * 0x8), control);

 	return DMA_STATUS_GOOD;
 }

 /*
  * Configures a DMA channel, including the peripheral bus width, if a
  * peripheral is attached to the channel, the polarity of the DMAReq and
  * DMAAck signals, etc.  This information should really be setup by the boot
  * code, since most likely the configuration won't change dynamically.
  * If the kernel has to call this function, it's recommended that it's
  * called from platform specific init code.  The driver should not need to
  * call this function.
  */
 int
 ppc4xx_init_dma_channel(unsigned int dmanr, ppc_dma_ch_t * p_init)
 {
 	unsigned int polarity;
 	uint32_t control = 0;
 	ppc_dma_ch_t *p_dma_ch = &dma_channels[dmanr];

 	DMA_MODE_READ = (unsigned long) DMA_TD;	/* Peripheral to Memory */
 	DMA_MODE_WRITE = 0;	/* Memory to Peripheral */

 	if (!p_init) {
 		printk("ppc4xx_init_dma_channel: NULL p_init\n");
 		return DMA_STATUS_NULL_POINTER;
 	}

 	if (dmanr >= MAX_PPC4xx_DMA_CHANNELS) {
 		printk("ppc4xx_init_dma_channel: bad channel %d\n", dmanr);
 		return DMA_STATUS_BAD_CHANNEL;
 	}

 #if DCRN_POL > 0
 	polarity = mfdcr(DCRN_POL);
 #else
 	polarity = 0;
 #endif

 	/* Setup the control register based on the values passed to
 	 * us in p_init.  Then, over-write the control register with this
 	 * new value.
 	 */
 	control |= SET_DMA_CONTROL;

 	/* clear all polarity signals and then "or" in new signal levels */
 	polarity &= ~GET_DMA_POLARITY(dmanr);
 	polarity |= p_init->polarity;
 #if DCRN_POL > 0
 	mtdcr(DCRN_POL, polarity);
 #endif
 	mtdcr(DCRN_DMACR0 + (dmanr * 0x8), control);

 	/* save these values in our dma channel structure */
 	memcpy(p_dma_ch, p_init, sizeof (ppc_dma_ch_t));

 	/*
 	 * The peripheral width values written in the control register are:
 	 *   PW_8                 0
 	 *   PW_16                1
 	 *   PW_32                2
 	 *   PW_64                3
 	 *
 	 *   Since the DMA count register takes the number of "transfers",
 	 *   we need to divide the count sent to us in certain
 	 *   functions by the appropriate number.  It so happens that our
 	 *   right shift value is equal to the peripheral width value.
 	 */
 	p_dma_ch->shift = p_init->pwidth;

 	/*
 	 * Save the control word for easy access.
 	 */
 	p_dma_ch->control = control;

 	mtdcr(DCRN_DMASR, 0xffffffff);	/* clear status register */
 	return DMA_STATUS_GOOD;
 }

 /*
  * This function returns the channel configuration.
  */
 int
 ppc4xx_get_channel_config(unsigned int dmanr, ppc_dma_ch_t * p_dma_ch)
 {
 	unsigned int polarity;
 	unsigned int control;

 	if (dmanr >= MAX_PPC4xx_DMA_CHANNELS) {
 		printk("ppc4xx_get_channel_config: bad channel %d\n", dmanr);
 		return DMA_STATUS_BAD_CHANNEL;
 	}

 	memcpy(p_dma_ch, &dma_channels[dmanr], sizeof (ppc_dma_ch_t));

 #if DCRN_POL > 0
 	polarity = mfdcr(DCRN_POL);
 #else
 	polarity = 0;
 #endif

 	p_dma_ch->polarity = polarity & GET_DMA_POLARITY(dmanr);
 	control = mfdcr(DCRN_DMACR0 + (dmanr * 0x8));

 	p_dma_ch->cp = GET_DMA_PRIORITY(control);
 	p_dma_ch->pwidth = GET_DMA_PW(control);
 	p_dma_ch->psc = GET_DMA_PSC(control);
 	p_dma_ch->pwc = GET_DMA_PWC(control);
 	p_dma_ch->phc = GET_DMA_PHC(control);
 	p_dma_ch->ce = GET_DMA_CE_ENABLE(control);
 	p_dma_ch->int_enable = GET_DMA_CIE_ENABLE(control);
 	p_dma_ch->shift = GET_DMA_PW(control);

 #ifdef CONFIG_PPC4xx_EDMA
 	p_dma_ch->pf = GET_DMA_PREFETCH(control);
 #else
 	p_dma_ch->ch_enable = GET_DMA_CH(control);
 	p_dma_ch->ece_enable = GET_DMA_ECE(control);
 	p_dma_ch->tcd_disable = GET_DMA_TCD(control);
 #endif
 	return DMA_STATUS_GOOD;
 }

 /*
  * Sets the priority for the DMA channel dmanr.
  * Since this is setup by the hardware init function, this function
  * can be used to dynamically change the priority of a channel.
  *
  * Acceptable priorities:
  *
  * PRIORITY_LOW
  * PRIORITY_MID_LOW
  * PRIORITY_MID_HIGH
  * PRIORITY_HIGH
  *
  */
 int
 ppc4xx_set_channel_priority(unsigned int dmanr, unsigned int priority)
 {
 	unsigned int control;

 	if (dmanr >= MAX_PPC4xx_DMA_CHANNELS) {
 		printk("ppc4xx_set_channel_priority: bad channel %d\n", dmanr);
 		return DMA_STATUS_BAD_CHANNEL;
 	}

 	if ((priority != PRIORITY_LOW) &&
 	    (priority != PRIORITY_MID_LOW) &&
 	    (priority != PRIORITY_MID_HIGH) && (priority != PRIORITY_HIGH)) {
 		printk("ppc4xx_set_channel_priority: bad priority: 0x%x\n", priority);
 	}

 	control = mfdcr(DCRN_DMACR0 + (dmanr * 0x8));
 	control |= SET_DMA_PRIORITY(priority);
 	mtdcr(DCRN_DMACR0 + (dmanr * 0x8), control);

 	return DMA_STATUS_GOOD;
 }

 /*
  * Returns the width of the peripheral attached to this channel. This assumes
  * that someone who knows the hardware configuration, boot code or some other
  * init code, already set the width.
  *
  * The return value is one of:
  *   PW_8
  *   PW_16
  *   PW_32
  *   PW_64
  *
  *   The function returns 0 on error.
  */
 unsigned int
 ppc4xx_get_peripheral_width(unsigned int dmanr)
 {
 	unsigned int control;

 	if (dmanr >= MAX_PPC4xx_DMA_CHANNELS) {
 		printk("ppc4xx_get_peripheral_width: bad channel %d\n", dmanr);
 		return DMA_STATUS_BAD_CHANNEL;
 	}

 	control = mfdcr(DCRN_DMACR0 + (dmanr * 0x8));

 	return (GET_DMA_PW(control));
 }

 /*
  * Clears the channel status bits
  */
 int
 ppc4xx_clr_dma_status(unsigned int dmanr)
 {
 	if (dmanr >= MAX_PPC4xx_DMA_CHANNELS) {
 		printk(KERN_ERR "ppc4xx_clr_dma_status: bad channel: %d\n", dmanr);
 		return DMA_STATUS_BAD_CHANNEL;
 	}
 	mtdcr(DCRN_DMASR, ((u32)DMA_CH0_ERR | (u32)DMA_CS0 | (u32)DMA_TS0) >> dmanr);
 	return DMA_STATUS_GOOD;
 }

 #ifdef CONFIG_PPC4xx_EDMA
 /*
  * Enables the burst on the channel (BTEN bit in the control/count register)
  * Note:
  * For scatter/gather dma, this function MUST be called before the
  * ppc4xx_alloc_dma_handle() func as the chan count register is copied into the
  * sgl list and used as each sgl element is added.
  */
 int
 ppc4xx_enable_burst(unsigned int dmanr)
 {
 	unsigned int ctc;
 	if (dmanr >= MAX_PPC4xx_DMA_CHANNELS) {
 		printk(KERN_ERR "ppc4xx_enable_burst: bad channel: %d\n", dmanr);
 		return DMA_STATUS_BAD_CHANNEL;
 	}
         ctc = mfdcr(DCRN_DMACT0 + (dmanr * 0x8)) | DMA_CTC_BTEN;
 	mtdcr(DCRN_DMACT0 + (dmanr * 0x8), ctc);
 	return DMA_STATUS_GOOD;
 }
 /*
  * Disables the burst on the channel (BTEN bit in the control/count register)
  * Note:
  * For scatter/gather dma, this function MUST be called before the
  * ppc4xx_alloc_dma_handle() func as the chan count register is copied into the
  * sgl list and used as each sgl element is added.
  */
 int
 ppc4xx_disable_burst(unsigned int dmanr)
 {
 	unsigned int ctc;
 	if (dmanr >= MAX_PPC4xx_DMA_CHANNELS) {
 		printk(KERN_ERR "ppc4xx_disable_burst: bad channel: %d\n", dmanr);
 		return DMA_STATUS_BAD_CHANNEL;
 	}
 	ctc = mfdcr(DCRN_DMACT0 + (dmanr * 0x8)) &~ DMA_CTC_BTEN;
 	mtdcr(DCRN_DMACT0 + (dmanr * 0x8), ctc);
 	return DMA_STATUS_GOOD;
 }
 /*
  * Sets the burst size (number of peripheral widths) for the channel
  * (BSIZ bits in the control/count register))
  * must be one of:
  *    DMA_CTC_BSIZ_2
  *    DMA_CTC_BSIZ_4
  *    DMA_CTC_BSIZ_8
  *    DMA_CTC_BSIZ_16
  * Note:
  * For scatter/gather dma, this function MUST be called before the
  * ppc4xx_alloc_dma_handle() func as the chan count register is copied into the
  * sgl list and used as each sgl element is added.
  */
 int
 ppc4xx_set_burst_size(unsigned int dmanr, unsigned int bsize)
 {
 	unsigned int ctc;
 	if (dmanr >= MAX_PPC4xx_DMA_CHANNELS) {
 		printk(KERN_ERR "ppc4xx_set_burst_size: bad channel: %d\n", dmanr);
 		return DMA_STATUS_BAD_CHANNEL;
 	}
 	ctc = mfdcr(DCRN_DMACT0 + (dmanr * 0x8)) &~ DMA_CTC_BSIZ_MSK;
 	ctc |= (bsize & DMA_CTC_BSIZ_MSK);
 	mtdcr(DCRN_DMACT0 + (dmanr * 0x8), ctc);
 	return DMA_STATUS_GOOD;
 }

 EXPORT_SYMBOL(ppc4xx_enable_burst);
 EXPORT_SYMBOL(ppc4xx_disable_burst);
 EXPORT_SYMBOL(ppc4xx_set_burst_size);
 #endif /* CONFIG_PPC4xx_EDMA */

 EXPORT_SYMBOL(ppc4xx_init_dma_channel);
 EXPORT_SYMBOL(ppc4xx_get_channel_config);
 EXPORT_SYMBOL(ppc4xx_set_channel_priority);
 EXPORT_SYMBOL(ppc4xx_get_peripheral_width);
 EXPORT_SYMBOL(dma_channels);
 EXPORT_SYMBOL(ppc4xx_set_src_addr);
 EXPORT_SYMBOL(ppc4xx_set_dst_addr);
 EXPORT_SYMBOL(ppc4xx_set_dma_addr);
 EXPORT_SYMBOL(ppc4xx_set_dma_addr2);
 EXPORT_SYMBOL(ppc4xx_enable_dma);
 EXPORT_SYMBOL(ppc4xx_disable_dma);
 EXPORT_SYMBOL(ppc4xx_set_dma_mode);
 EXPORT_SYMBOL(ppc4xx_set_dma_count);
 EXPORT_SYMBOL(ppc4xx_get_dma_residue);
 EXPORT_SYMBOL(ppc4xx_enable_dma_interrupt);
 EXPORT_SYMBOL(ppc4xx_disable_dma_interrupt);
 EXPORT_SYMBOL(ppc4xx_get_dma_status);
 EXPORT_SYMBOL(ppc4xx_clr_dma_status);
	/*
	* IBM PPC4xx DMA engine core library
	*
	* Copyright 2000-2004 MontaVista Software Inc.
	*
	* Cleaned up and converted to new DCR access
	* Matt Porter <mporter@kernel.crashing.org>
	*
	* Original code by Armin Kuster <akuster@mvista.com>
	* and Pete Popov <ppopov@mvista.com>
	*
	* This program is free software; you can redistribute it and/or modify it
	* under the terms of the GNU General Public License as published by the
	* Free Software Foundation; either version 2 of the License, or (at your
	* option) any later version.
	*
	* You should have received a copy of the GNU General Public License along
	* with this program; if not, write to the Free Software Foundation, Inc.,
	* 675 Mass Ave, Cambridge, MA 02139, USA.
	*/

	#include <linux/kernel.h>
	#include <linux/mm.h>
	#include <linux/miscdevice.h>
	#include <linux/init.h>
	#include <linux/module.h>

	#include <asm/system.h>
	#include <asm/io.h>
	#include <asm/dma.h>
	#include <asm/ppc4xx_dma.h>

	ppc_dma_ch_t dma_channels[MAX_PPC4xx_DMA_CHANNELS];

	int
	ppc4xx_get_dma_status(void)
	{
	return (mfdcr(DCRN_DMASR));
	}

	void
	ppc4xx_set_src_addr(int dmanr, phys_addr_t src_addr)
	{
	if (dmanr >= MAX_PPC4xx_DMA_CHANNELS) {
	printk("set_src_addr: bad channel: %d\n", dmanr);
	return;
	}

	#ifdef PPC4xx_DMA_64BIT
	mtdcr(DCRN_DMASAH0 + dmanr*2, (u32)(src_addr >> 32));
	#else
	mtdcr(DCRN_DMASA0 + dmanr*2, (u32)src_addr);
	#endif
	}

	void
	ppc4xx_set_dst_addr(int dmanr, phys_addr_t dst_addr)
	{
	if (dmanr >= MAX_PPC4xx_DMA_CHANNELS) {
	printk("set_dst_addr: bad channel: %d\n", dmanr);
	return;
	}

	#ifdef PPC4xx_DMA_64BIT
	mtdcr(DCRN_DMADAH0 + dmanr*2, (u32)(dst_addr >> 32));
	#else
	mtdcr(DCRN_DMADA0 + dmanr*2, (u32)dst_addr);
	#endif
	}

	void
	ppc4xx_enable_dma(unsigned int dmanr)
	{
	unsigned int control;
	ppc_dma_ch_t *p_dma_ch = &dma_channels[dmanr];
	unsigned int status_bits[] = { DMA_CS0 \| DMA_TS0 \| DMA_CH0_ERR,
	DMA_CS1 \| DMA_TS1 \| DMA_CH1_ERR,
	DMA_CS2 \| DMA_TS2 \| DMA_CH2_ERR,
	DMA_CS3 \| DMA_TS3 \| DMA_CH3_ERR};

	if (p_dma_ch->in_use) {
	printk("enable_dma: channel %d in use\n", dmanr);
	return;
	}

	if (dmanr >= MAX_PPC4xx_DMA_CHANNELS) {
	printk("enable_dma: bad channel: %d\n", dmanr);
	return;
	}

	if (p_dma_ch->mode == DMA_MODE_READ) {
	/* peripheral to memory */
	ppc4xx_set_src_addr(dmanr, 0);
	ppc4xx_set_dst_addr(dmanr, p_dma_ch->addr);
	} else if (p_dma_ch->mode == DMA_MODE_WRITE) {
	/* memory to peripheral */
	ppc4xx_set_src_addr(dmanr, p_dma_ch->addr);
	ppc4xx_set_dst_addr(dmanr, 0);
	}

	/* for other xfer modes, the addresses are already set */
	control = mfdcr(DCRN_DMACR0 + (dmanr * 0x8));

	control &= ~(DMA_TM_MASK \| DMA_TD); /* clear all mode bits */
	if (p_dma_ch->mode == DMA_MODE_MM) {
	/* software initiated memory to memory */
	control \|= DMA_ETD_OUTPUT \| DMA_TCE_ENABLE;
	}

	mtdcr(DCRN_DMACR0 + (dmanr * 0x8), control);

	/*
	* Clear the CS, TS, RI bits for the channel from DMASR. This
	* has been observed to happen correctly only after the mode and
	* ETD/DCE bits in DMACRx are set above. Must do this before
	* enabling the channel.
	*/

	mtdcr(DCRN_DMASR, status_bits[dmanr]);

	/*
	* For device-paced transfers, Terminal Count Enable apparently
	* must be on, and this must be turned on after the mode, etc.
	* bits are cleared above (at least on Redwood-6).
	*/

	if ((p_dma_ch->mode == DMA_MODE_MM_DEVATDST) \|\|
	(p_dma_ch->mode == DMA_MODE_MM_DEVATSRC))
	control \|= DMA_TCE_ENABLE;

	/*
	* Now enable the channel.
	*/

	control \|= (p_dma_ch->mode \| DMA_CE_ENABLE);

	mtdcr(DCRN_DMACR0 + (dmanr * 0x8), control);

	p_dma_ch->in_use = 1;
	}

	void
	ppc4xx_disable_dma(unsigned int dmanr)
	{
	unsigned int control;
	ppc_dma_ch_t *p_dma_ch = &dma_channels[dmanr];

	if (!p_dma_ch->in_use) {
	printk("disable_dma: channel %d not in use\n", dmanr);
	return;
	}

	if (dmanr >= MAX_PPC4xx_DMA_CHANNELS) {
	printk("disable_dma: bad channel: %d\n", dmanr);
	return;
	}

	control = mfdcr(DCRN_DMACR0 + (dmanr * 0x8));
	control &= ~DMA_CE_ENABLE;
	mtdcr(DCRN_DMACR0 + (dmanr * 0x8), control);

	p_dma_ch->in_use = 0;
	}

	/*
	* Sets the dma mode for single DMA transfers only.
	* For scatter/gather transfers, the mode is passed to the
	* alloc_dma_handle() function as one of the parameters.
	*
	* The mode is simply saved and used later. This allows
	* the driver to call set_dma_mode() and set_dma_addr() in
	* any order.
	*
	* Valid mode values are:
	*
	* DMA_MODE_READ peripheral to memory
	* DMA_MODE_WRITE memory to peripheral
	* DMA_MODE_MM memory to memory
	* DMA_MODE_MM_DEVATSRC device-paced memory to memory, device at src
	* DMA_MODE_MM_DEVATDST device-paced memory to memory, device at dst
	*/
	int
	ppc4xx_set_dma_mode(unsigned int dmanr, unsigned int mode)
	{
	ppc_dma_ch_t *p_dma_ch = &dma_channels[dmanr];

	if (dmanr >= MAX_PPC4xx_DMA_CHANNELS) {
	printk("set_dma_mode: bad channel 0x%x\n", dmanr);
	return DMA_STATUS_BAD_CHANNEL;
	}

	p_dma_ch->mode = mode;

	return DMA_STATUS_GOOD;
	}

	/*
	* Sets the DMA Count register. Note that 'count' is in bytes.
	* However, the DMA Count register counts the number of "transfers",
	* where each transfer is equal to the bus width. Thus, count
	* MUST be a multiple of the bus width.
	*/
	void
	ppc4xx_set_dma_count(unsigned int dmanr, unsigned int count)
	{
	ppc_dma_ch_t *p_dma_ch = &dma_channels[dmanr];

	#ifdef DEBUG_4xxDMA
	{
	int error = 0;
	switch (p_dma_ch->pwidth) {
	case PW_8:
	break;
	case PW_16:
	if (count & 0x1)
	error = 1;
	break;
	case PW_32:
	if (count & 0x3)
	error = 1;
	break;
	case PW_64:
	if (count & 0x7)
	error = 1;
	break;
	default:
	printk("set_dma_count: invalid bus width: 0x%x\n",
	p_dma_ch->pwidth);
	return;
	}
	if (error)
	printk
	("Warning: set_dma_count count 0x%x bus width %d\n",
	count, p_dma_ch->pwidth);
	}
	#endif

	count = count >> p_dma_ch->shift;

	mtdcr(DCRN_DMACT0 + (dmanr * 0x8), count);
	}

	/*
	* Returns the number of bytes left to be transferred.
	* After a DMA transfer, this should return zero.
	* Reading this while a DMA transfer is still in progress will return
	* unpredictable results.
	*/
	int
	ppc4xx_get_dma_residue(unsigned int dmanr)
	{
	unsigned int count;
	ppc_dma_ch_t *p_dma_ch = &dma_channels[dmanr];

	if (dmanr >= MAX_PPC4xx_DMA_CHANNELS) {
	printk("ppc4xx_get_dma_residue: bad channel 0x%x\n", dmanr);
	return DMA_STATUS_BAD_CHANNEL;
	}

	count = mfdcr(DCRN_DMACT0 + (dmanr * 0x8));

	return (count << p_dma_ch->shift);
	}

	/*
	* Sets the DMA address for a memory to peripheral or peripheral
	* to memory transfer. The address is just saved in the channel
	* structure for now and used later in enable_dma().
	*/
	void
	ppc4xx_set_dma_addr(unsigned int dmanr, phys_addr_t addr)
	{
	ppc_dma_ch_t *p_dma_ch = &dma_channels[dmanr];

	if (dmanr >= MAX_PPC4xx_DMA_CHANNELS) {
	printk("ppc4xx_set_dma_addr: bad channel: %d\n", dmanr);
	return;
	}

	#ifdef DEBUG_4xxDMA
	{
	int error = 0;
	switch (p_dma_ch->pwidth) {
	case PW_8:
	break;
	case PW_16:
	if ((unsigned) addr & 0x1)
	error = 1;
	break;
	case PW_32:
	if ((unsigned) addr & 0x3)
	error = 1;
	break;
	case PW_64:
	if ((unsigned) addr & 0x7)
	error = 1;
	break;
	default:
	printk("ppc4xx_set_dma_addr: invalid bus width: 0x%x\n",
	p_dma_ch->pwidth);
	return;
	}
	if (error)
	printk("Warning: ppc4xx_set_dma_addr addr 0x%x bus width %d\n",
	addr, p_dma_ch->pwidth);
	}
	#endif

	/* save dma address and program it later after we know the xfer mode */
	p_dma_ch->addr = addr;
	}

	/*
	* Sets both DMA addresses for a memory to memory transfer.
	* For memory to peripheral or peripheral to memory transfers
	* the function set_dma_addr() should be used instead.
	*/
	void
	ppc4xx_set_dma_addr2(unsigned int dmanr, phys_addr_t src_dma_addr,
	phys_addr_t dst_dma_addr)
	{
	if (dmanr >= MAX_PPC4xx_DMA_CHANNELS) {
	printk("ppc4xx_set_dma_addr2: bad channel: %d\n", dmanr);
	return;
	}

	#ifdef DEBUG_4xxDMA
	{
	ppc_dma_ch_t *p_dma_ch = &dma_channels[dmanr];
	int error = 0;
	switch (p_dma_ch->pwidth) {
	case PW_8:
	break;
	case PW_16:
	if (((unsigned) src_dma_addr & 0x1) \|\|
	((unsigned) dst_dma_addr & 0x1)
	)
	error = 1;
	break;
	case PW_32:
	if (((unsigned) src_dma_addr & 0x3) \|\|
	((unsigned) dst_dma_addr & 0x3)
	)
	error = 1;
	break;
	case PW_64:
	if (((unsigned) src_dma_addr & 0x7) \|\|
	((unsigned) dst_dma_addr & 0x7)
	)
	error = 1;
	break;
	default:
	printk("ppc4xx_set_dma_addr2: invalid bus width: 0x%x\n",
	p_dma_ch->pwidth);
	return;
	}
	if (error)
	printk
	("Warning: ppc4xx_set_dma_addr2 src 0x%x dst 0x%x bus width %d\n",
	src_dma_addr, dst_dma_addr, p_dma_ch->pwidth);
	}
	#endif

	ppc4xx_set_src_addr(dmanr, src_dma_addr);
	ppc4xx_set_dst_addr(dmanr, dst_dma_addr);
	}

	/*
	* Enables the channel interrupt.
	*
	* If performing a scatter/gatter transfer, this function
	* MUST be called before calling alloc_dma_handle() and building
	* the sgl list. Otherwise, interrupts will not be enabled, if
	* they were previously disabled.
	*/
	int
	ppc4xx_enable_dma_interrupt(unsigned int dmanr)
	{
	unsigned int control;
	ppc_dma_ch_t *p_dma_ch = &dma_channels[dmanr];

	if (dmanr >= MAX_PPC4xx_DMA_CHANNELS) {
	printk("ppc4xx_enable_dma_interrupt: bad channel: %d\n", dmanr);
	return DMA_STATUS_BAD_CHANNEL;
	}

	p_dma_ch->int_enable = 1;

	control = mfdcr(DCRN_DMACR0 + (dmanr * 0x8));
	control \|= DMA_CIE_ENABLE; /* Channel Interrupt Enable */
	mtdcr(DCRN_DMACR0 + (dmanr * 0x8), control);

	return DMA_STATUS_GOOD;
	}

	/*
	* Disables the channel interrupt.
	*
	* If performing a scatter/gatter transfer, this function
	* MUST be called before calling alloc_dma_handle() and building
	* the sgl list. Otherwise, interrupts will not be disabled, if
	* they were previously enabled.
	*/
	int
	ppc4xx_disable_dma_interrupt(unsigned int dmanr)
	{
	unsigned int control;
	ppc_dma_ch_t *p_dma_ch = &dma_channels[dmanr];

	if (dmanr >= MAX_PPC4xx_DMA_CHANNELS) {
	printk("ppc4xx_disable_dma_interrupt: bad channel: %d\n", dmanr);
	return DMA_STATUS_BAD_CHANNEL;
	}

	p_dma_ch->int_enable = 0;

	control = mfdcr(DCRN_DMACR0 + (dmanr * 0x8));
	control &= ~DMA_CIE_ENABLE; /* Channel Interrupt Enable */
	mtdcr(DCRN_DMACR0 + (dmanr * 0x8), control);

	return DMA_STATUS_GOOD;
	}

	/*
	* Configures a DMA channel, including the peripheral bus width, if a
	* peripheral is attached to the channel, the polarity of the DMAReq and
	* DMAAck signals, etc. This information should really be setup by the boot
	* code, since most likely the configuration won't change dynamically.
	* If the kernel has to call this function, it's recommended that it's
	* called from platform specific init code. The driver should not need to
	* call this function.
	*/
	int
	ppc4xx_init_dma_channel(unsigned int dmanr, ppc_dma_ch_t * p_init)
	{
	unsigned int polarity;
	uint32_t control = 0;
	ppc_dma_ch_t *p_dma_ch = &dma_channels[dmanr];

	DMA_MODE_READ = (unsigned long) DMA_TD; /* Peripheral to Memory */
	DMA_MODE_WRITE = 0; /* Memory to Peripheral */

	if (!p_init) {
	printk("ppc4xx_init_dma_channel: NULL p_init\n");
	return DMA_STATUS_NULL_POINTER;
	}

	if (dmanr >= MAX_PPC4xx_DMA_CHANNELS) {
	printk("ppc4xx_init_dma_channel: bad channel %d\n", dmanr);
	return DMA_STATUS_BAD_CHANNEL;
	}

	#if DCRN_POL > 0
	polarity = mfdcr(DCRN_POL);
	#else
	polarity = 0;
	#endif

	/* Setup the control register based on the values passed to
	* us in p_init. Then, over-write the control register with this
	* new value.
	*/
	control \|= SET_DMA_CONTROL;

	/* clear all polarity signals and then "or" in new signal levels */
	polarity &= ~GET_DMA_POLARITY(dmanr);
	polarity \|= p_init->polarity;
	#if DCRN_POL > 0
	mtdcr(DCRN_POL, polarity);
	#endif
	mtdcr(DCRN_DMACR0 + (dmanr * 0x8), control);

	/* save these values in our dma channel structure */
	memcpy(p_dma_ch, p_init, sizeof (ppc_dma_ch_t));

	/*
	* The peripheral width values written in the control register are:
	* PW_8 0
	* PW_16 1
	* PW_32 2
	* PW_64 3
	*
	* Since the DMA count register takes the number of "transfers",
	* we need to divide the count sent to us in certain
	* functions by the appropriate number. It so happens that our
	* right shift value is equal to the peripheral width value.
	*/
	p_dma_ch->shift = p_init->pwidth;

	/*
	* Save the control word for easy access.
	*/
	p_dma_ch->control = control;

	mtdcr(DCRN_DMASR, 0xffffffff); /* clear status register */
	return DMA_STATUS_GOOD;
	}

	/*
	* This function returns the channel configuration.
	*/
	int
	ppc4xx_get_channel_config(unsigned int dmanr, ppc_dma_ch_t * p_dma_ch)
	{
	unsigned int polarity;
	unsigned int control;

	if (dmanr >= MAX_PPC4xx_DMA_CHANNELS) {
	printk("ppc4xx_get_channel_config: bad channel %d\n", dmanr);
	return DMA_STATUS_BAD_CHANNEL;
	}

	memcpy(p_dma_ch, &dma_channels[dmanr], sizeof (ppc_dma_ch_t));

	#if DCRN_POL > 0
	polarity = mfdcr(DCRN_POL);
	#else
	polarity = 0;
	#endif

	p_dma_ch->polarity = polarity & GET_DMA_POLARITY(dmanr);
	control = mfdcr(DCRN_DMACR0 + (dmanr * 0x8));

	p_dma_ch->cp = GET_DMA_PRIORITY(control);
	p_dma_ch->pwidth = GET_DMA_PW(control);
	p_dma_ch->psc = GET_DMA_PSC(control);
	p_dma_ch->pwc = GET_DMA_PWC(control);
	p_dma_ch->phc = GET_DMA_PHC(control);
	p_dma_ch->ce = GET_DMA_CE_ENABLE(control);
	p_dma_ch->int_enable = GET_DMA_CIE_ENABLE(control);
	p_dma_ch->shift = GET_DMA_PW(control);

	#ifdef CONFIG_PPC4xx_EDMA
	p_dma_ch->pf = GET_DMA_PREFETCH(control);
	#else
	p_dma_ch->ch_enable = GET_DMA_CH(control);
	p_dma_ch->ece_enable = GET_DMA_ECE(control);
	p_dma_ch->tcd_disable = GET_DMA_TCD(control);
	#endif
	return DMA_STATUS_GOOD;
	}

	/*
	* Sets the priority for the DMA channel dmanr.
	* Since this is setup by the hardware init function, this function
	* can be used to dynamically change the priority of a channel.
	*
	* Acceptable priorities:
	*
	* PRIORITY_LOW
	* PRIORITY_MID_LOW
	* PRIORITY_MID_HIGH
	* PRIORITY_HIGH
	*
	*/
	int
	ppc4xx_set_channel_priority(unsigned int dmanr, unsigned int priority)
	{
	unsigned int control;

	if (dmanr >= MAX_PPC4xx_DMA_CHANNELS) {
	printk("ppc4xx_set_channel_priority: bad channel %d\n", dmanr);
	return DMA_STATUS_BAD_CHANNEL;
	}

	if ((priority != PRIORITY_LOW) &&
	(priority != PRIORITY_MID_LOW) &&
	(priority != PRIORITY_MID_HIGH) && (priority != PRIORITY_HIGH)) {
	printk("ppc4xx_set_channel_priority: bad priority: 0x%x\n", priority);
	}

	control = mfdcr(DCRN_DMACR0 + (dmanr * 0x8));
	control \|= SET_DMA_PRIORITY(priority);
	mtdcr(DCRN_DMACR0 + (dmanr * 0x8), control);

	return DMA_STATUS_GOOD;
	}

	/*
	* Returns the width of the peripheral attached to this channel. This assumes
	* that someone who knows the hardware configuration, boot code or some other
	* init code, already set the width.
	*
	* The return value is one of:
	* PW_8
	* PW_16
	* PW_32
	* PW_64
	*
	* The function returns 0 on error.
	*/
	unsigned int
	ppc4xx_get_peripheral_width(unsigned int dmanr)
	{
	unsigned int control;

	if (dmanr >= MAX_PPC4xx_DMA_CHANNELS) {
	printk("ppc4xx_get_peripheral_width: bad channel %d\n", dmanr);
	return DMA_STATUS_BAD_CHANNEL;
	}

	control = mfdcr(DCRN_DMACR0 + (dmanr * 0x8));

	return (GET_DMA_PW(control));
	}

	/*
	* Clears the channel status bits
	*/
	int
	ppc4xx_clr_dma_status(unsigned int dmanr)
	{
	if (dmanr >= MAX_PPC4xx_DMA_CHANNELS) {
	printk(KERN_ERR "ppc4xx_clr_dma_status: bad channel: %d\n", dmanr);
	return DMA_STATUS_BAD_CHANNEL;
	}
	mtdcr(DCRN_DMASR, ((u32)DMA_CH0_ERR \| (u32)DMA_CS0 \| (u32)DMA_TS0) >> dmanr);
	return DMA_STATUS_GOOD;
	}

	#ifdef CONFIG_PPC4xx_EDMA
	/*
	* Enables the burst on the channel (BTEN bit in the control/count register)
	* Note:
	* For scatter/gather dma, this function MUST be called before the
	* ppc4xx_alloc_dma_handle() func as the chan count register is copied into the
	* sgl list and used as each sgl element is added.
	*/
	int
	ppc4xx_enable_burst(unsigned int dmanr)
	{
	unsigned int ctc;
	if (dmanr >= MAX_PPC4xx_DMA_CHANNELS) {
	printk(KERN_ERR "ppc4xx_enable_burst: bad channel: %d\n", dmanr);
	return DMA_STATUS_BAD_CHANNEL;
	}
	ctc = mfdcr(DCRN_DMACT0 + (dmanr * 0x8)) \| DMA_CTC_BTEN;
	mtdcr(DCRN_DMACT0 + (dmanr * 0x8), ctc);
	return DMA_STATUS_GOOD;
	}
	/*
	* Disables the burst on the channel (BTEN bit in the control/count register)
	* Note:
	* For scatter/gather dma, this function MUST be called before the
	* ppc4xx_alloc_dma_handle() func as the chan count register is copied into the
	* sgl list and used as each sgl element is added.
	*/
	int
	ppc4xx_disable_burst(unsigned int dmanr)
	{
	unsigned int ctc;
	if (dmanr >= MAX_PPC4xx_DMA_CHANNELS) {
	printk(KERN_ERR "ppc4xx_disable_burst: bad channel: %d\n", dmanr);
	return DMA_STATUS_BAD_CHANNEL;
	}
	ctc = mfdcr(DCRN_DMACT0 + (dmanr * 0x8)) &~ DMA_CTC_BTEN;
	mtdcr(DCRN_DMACT0 + (dmanr * 0x8), ctc);
	return DMA_STATUS_GOOD;
	}
	/*
	* Sets the burst size (number of peripheral widths) for the channel
	* (BSIZ bits in the control/count register))
	* must be one of:
	* DMA_CTC_BSIZ_2
	* DMA_CTC_BSIZ_4
	* DMA_CTC_BSIZ_8
	* DMA_CTC_BSIZ_16
	* Note:
	* For scatter/gather dma, this function MUST be called before the
	* ppc4xx_alloc_dma_handle() func as the chan count register is copied into the
	* sgl list and used as each sgl element is added.
	*/
	int
	ppc4xx_set_burst_size(unsigned int dmanr, unsigned int bsize)
	{
	unsigned int ctc;
	if (dmanr >= MAX_PPC4xx_DMA_CHANNELS) {
	printk(KERN_ERR "ppc4xx_set_burst_size: bad channel: %d\n", dmanr);
	return DMA_STATUS_BAD_CHANNEL;
	}
	ctc = mfdcr(DCRN_DMACT0 + (dmanr * 0x8)) &~ DMA_CTC_BSIZ_MSK;
	ctc \|= (bsize & DMA_CTC_BSIZ_MSK);
	mtdcr(DCRN_DMACT0 + (dmanr * 0x8), ctc);
	return DMA_STATUS_GOOD;
	}

	EXPORT_SYMBOL(ppc4xx_enable_burst);
	EXPORT_SYMBOL(ppc4xx_disable_burst);
	EXPORT_SYMBOL(ppc4xx_set_burst_size);
	#endif /* CONFIG_PPC4xx_EDMA */

	EXPORT_SYMBOL(ppc4xx_init_dma_channel);
	EXPORT_SYMBOL(ppc4xx_get_channel_config);
	EXPORT_SYMBOL(ppc4xx_set_channel_priority);
	EXPORT_SYMBOL(ppc4xx_get_peripheral_width);
	EXPORT_SYMBOL(dma_channels);
	EXPORT_SYMBOL(ppc4xx_set_src_addr);
	EXPORT_SYMBOL(ppc4xx_set_dst_addr);
	EXPORT_SYMBOL(ppc4xx_set_dma_addr);
	EXPORT_SYMBOL(ppc4xx_set_dma_addr2);
	EXPORT_SYMBOL(ppc4xx_enable_dma);
	EXPORT_SYMBOL(ppc4xx_disable_dma);
	EXPORT_SYMBOL(ppc4xx_set_dma_mode);
	EXPORT_SYMBOL(ppc4xx_set_dma_count);
	EXPORT_SYMBOL(ppc4xx_get_dma_residue);
	EXPORT_SYMBOL(ppc4xx_enable_dma_interrupt);
	EXPORT_SYMBOL(ppc4xx_disable_dma_interrupt);
	EXPORT_SYMBOL(ppc4xx_get_dma_status);
	EXPORT_SYMBOL(ppc4xx_clr_dma_status);