| /* |
| * Copyright 2001-2003 SuSE Labs. |
| * Distributed under the GNU public license, v2. |
| * |
| * This is a GART driver for the AMD Opteron/Athlon64 on-CPU northbridge. |
| * It also includes support for the AMD 8151 AGP bridge, |
| * although it doesn't actually do much, as all the real |
| * work is done in the northbridge(s). |
| */ |
| |
| #include <linux/module.h> |
| #include <linux/pci.h> |
| #include <linux/init.h> |
| #include <linux/agp_backend.h> |
| #include <linux/mmzone.h> |
| #include <asm/page.h> /* PAGE_SIZE */ |
| #include <asm/e820.h> |
| #include <asm/k8.h> |
| #include "agp.h" |
| |
| /* PTE bits. */ |
| #define GPTE_VALID 1 |
| #define GPTE_COHERENT 2 |
| |
| /* Aperture control register bits. */ |
| #define GARTEN (1<<0) |
| #define DISGARTCPU (1<<4) |
| #define DISGARTIO (1<<5) |
| |
| /* GART cache control register bits. */ |
| #define INVGART (1<<0) |
| #define GARTPTEERR (1<<1) |
| |
| /* K8 On-cpu GART registers */ |
| #define AMD64_GARTAPERTURECTL 0x90 |
| #define AMD64_GARTAPERTUREBASE 0x94 |
| #define AMD64_GARTTABLEBASE 0x98 |
| #define AMD64_GARTCACHECTL 0x9c |
| #define AMD64_GARTEN (1<<0) |
| |
| /* NVIDIA K8 registers */ |
| #define NVIDIA_X86_64_0_APBASE 0x10 |
| #define NVIDIA_X86_64_1_APBASE1 0x50 |
| #define NVIDIA_X86_64_1_APLIMIT1 0x54 |
| #define NVIDIA_X86_64_1_APSIZE 0xa8 |
| #define NVIDIA_X86_64_1_APBASE2 0xd8 |
| #define NVIDIA_X86_64_1_APLIMIT2 0xdc |
| |
| /* ULi K8 registers */ |
| #define ULI_X86_64_BASE_ADDR 0x10 |
| #define ULI_X86_64_HTT_FEA_REG 0x50 |
| #define ULI_X86_64_ENU_SCR_REG 0x54 |
| |
| static struct resource *aperture_resource; |
| static int __initdata agp_try_unsupported = 1; |
| |
| static void amd64_tlbflush(struct agp_memory *temp) |
| { |
| k8_flush_garts(); |
| } |
| |
| static int amd64_insert_memory(struct agp_memory *mem, off_t pg_start, int type) |
| { |
| int i, j, num_entries; |
| long long tmp; |
| int mask_type; |
| struct agp_bridge_data *bridge = mem->bridge; |
| u32 pte; |
| |
| num_entries = agp_num_entries(); |
| |
| if (type != mem->type) |
| return -EINVAL; |
| mask_type = bridge->driver->agp_type_to_mask_type(bridge, type); |
| if (mask_type != 0) |
| return -EINVAL; |
| |
| |
| /* Make sure we can fit the range in the gatt table. */ |
| /* FIXME: could wrap */ |
| if (((unsigned long)pg_start + mem->page_count) > num_entries) |
| return -EINVAL; |
| |
| j = pg_start; |
| |
| /* gatt table should be empty. */ |
| while (j < (pg_start + mem->page_count)) { |
| if (!PGE_EMPTY(agp_bridge, readl(agp_bridge->gatt_table+j))) |
| return -EBUSY; |
| j++; |
| } |
| |
| if (mem->is_flushed == FALSE) { |
| global_cache_flush(); |
| mem->is_flushed = TRUE; |
| } |
| |
| for (i = 0, j = pg_start; i < mem->page_count; i++, j++) { |
| tmp = agp_bridge->driver->mask_memory(agp_bridge, |
| mem->memory[i], mask_type); |
| |
| BUG_ON(tmp & 0xffffff0000000ffcULL); |
| pte = (tmp & 0x000000ff00000000ULL) >> 28; |
| pte |=(tmp & 0x00000000fffff000ULL); |
| pte |= GPTE_VALID | GPTE_COHERENT; |
| |
| writel(pte, agp_bridge->gatt_table+j); |
| readl(agp_bridge->gatt_table+j); /* PCI Posting. */ |
| } |
| amd64_tlbflush(mem); |
| return 0; |
| } |
| |
| /* |
| * This hack alters the order element according |
| * to the size of a long. It sucks. I totally disown this, even |
| * though it does appear to work for the most part. |
| */ |
| static struct aper_size_info_32 amd64_aperture_sizes[7] = |
| { |
| {32, 8192, 3+(sizeof(long)/8), 0 }, |
| {64, 16384, 4+(sizeof(long)/8), 1<<1 }, |
| {128, 32768, 5+(sizeof(long)/8), 1<<2 }, |
| {256, 65536, 6+(sizeof(long)/8), 1<<1 | 1<<2 }, |
| {512, 131072, 7+(sizeof(long)/8), 1<<3 }, |
| {1024, 262144, 8+(sizeof(long)/8), 1<<1 | 1<<3}, |
| {2048, 524288, 9+(sizeof(long)/8), 1<<2 | 1<<3} |
| }; |
| |
| |
| /* |
| * Get the current Aperture size from the x86-64. |
| * Note, that there may be multiple x86-64's, but we just return |
| * the value from the first one we find. The set_size functions |
| * keep the rest coherent anyway. Or at least should do. |
| */ |
| static int amd64_fetch_size(void) |
| { |
| struct pci_dev *dev; |
| int i; |
| u32 temp; |
| struct aper_size_info_32 *values; |
| |
| dev = k8_northbridges[0]; |
| if (dev==NULL) |
| return 0; |
| |
| pci_read_config_dword(dev, AMD64_GARTAPERTURECTL, &temp); |
| temp = (temp & 0xe); |
| values = A_SIZE_32(amd64_aperture_sizes); |
| |
| for (i = 0; i < agp_bridge->driver->num_aperture_sizes; i++) { |
| if (temp == values[i].size_value) { |
| agp_bridge->previous_size = |
| agp_bridge->current_size = (void *) (values + i); |
| |
| agp_bridge->aperture_size_idx = i; |
| return values[i].size; |
| } |
| } |
| return 0; |
| } |
| |
| /* |
| * In a multiprocessor x86-64 system, this function gets |
| * called once for each CPU. |
| */ |
| static u64 amd64_configure (struct pci_dev *hammer, u64 gatt_table) |
| { |
| u64 aperturebase; |
| u32 tmp; |
| u64 addr, aper_base; |
| |
| /* Address to map to */ |
| pci_read_config_dword (hammer, AMD64_GARTAPERTUREBASE, &tmp); |
| aperturebase = tmp << 25; |
| aper_base = (aperturebase & PCI_BASE_ADDRESS_MEM_MASK); |
| |
| /* address of the mappings table */ |
| addr = (u64) gatt_table; |
| addr >>= 12; |
| tmp = (u32) addr<<4; |
| tmp &= ~0xf; |
| pci_write_config_dword (hammer, AMD64_GARTTABLEBASE, tmp); |
| |
| /* Enable GART translation for this hammer. */ |
| pci_read_config_dword(hammer, AMD64_GARTAPERTURECTL, &tmp); |
| tmp |= GARTEN; |
| tmp &= ~(DISGARTCPU | DISGARTIO); |
| pci_write_config_dword(hammer, AMD64_GARTAPERTURECTL, tmp); |
| |
| return aper_base; |
| } |
| |
| |
| static const struct aper_size_info_32 amd_8151_sizes[7] = |
| { |
| {2048, 524288, 9, 0x00000000 }, /* 0 0 0 0 0 0 */ |
| {1024, 262144, 8, 0x00000400 }, /* 1 0 0 0 0 0 */ |
| {512, 131072, 7, 0x00000600 }, /* 1 1 0 0 0 0 */ |
| {256, 65536, 6, 0x00000700 }, /* 1 1 1 0 0 0 */ |
| {128, 32768, 5, 0x00000720 }, /* 1 1 1 1 0 0 */ |
| {64, 16384, 4, 0x00000730 }, /* 1 1 1 1 1 0 */ |
| {32, 8192, 3, 0x00000738 } /* 1 1 1 1 1 1 */ |
| }; |
| |
| static int amd_8151_configure(void) |
| { |
| unsigned long gatt_bus = virt_to_gart(agp_bridge->gatt_table_real); |
| int i; |
| |
| /* Configure AGP regs in each x86-64 host bridge. */ |
| for (i = 0; i < num_k8_northbridges; i++) { |
| agp_bridge->gart_bus_addr = |
| amd64_configure(k8_northbridges[i], gatt_bus); |
| } |
| k8_flush_garts(); |
| return 0; |
| } |
| |
| |
| static void amd64_cleanup(void) |
| { |
| u32 tmp; |
| int i; |
| for (i = 0; i < num_k8_northbridges; i++) { |
| struct pci_dev *dev = k8_northbridges[i]; |
| /* disable gart translation */ |
| pci_read_config_dword (dev, AMD64_GARTAPERTURECTL, &tmp); |
| tmp &= ~AMD64_GARTEN; |
| pci_write_config_dword (dev, AMD64_GARTAPERTURECTL, tmp); |
| } |
| } |
| |
| |
| static const struct agp_bridge_driver amd_8151_driver = { |
| .owner = THIS_MODULE, |
| .aperture_sizes = amd_8151_sizes, |
| .size_type = U32_APER_SIZE, |
| .num_aperture_sizes = 7, |
| .configure = amd_8151_configure, |
| .fetch_size = amd64_fetch_size, |
| .cleanup = amd64_cleanup, |
| .tlb_flush = amd64_tlbflush, |
| .mask_memory = agp_generic_mask_memory, |
| .masks = NULL, |
| .agp_enable = agp_generic_enable, |
| .cache_flush = global_cache_flush, |
| .create_gatt_table = agp_generic_create_gatt_table, |
| .free_gatt_table = agp_generic_free_gatt_table, |
| .insert_memory = amd64_insert_memory, |
| .remove_memory = agp_generic_remove_memory, |
| .alloc_by_type = agp_generic_alloc_by_type, |
| .free_by_type = agp_generic_free_by_type, |
| .agp_alloc_page = agp_generic_alloc_page, |
| .agp_destroy_page = agp_generic_destroy_page, |
| .agp_type_to_mask_type = agp_generic_type_to_mask_type, |
| }; |
| |
| /* Some basic sanity checks for the aperture. */ |
| static int __devinit aperture_valid(u64 aper, u32 size) |
| { |
| if (aper == 0) { |
| printk(KERN_ERR PFX "No aperture\n"); |
| return 0; |
| } |
| if (size < 32*1024*1024) { |
| printk(KERN_ERR PFX "Aperture too small (%d MB)\n", size>>20); |
| return 0; |
| } |
| if ((u64)aper + size > 0x100000000ULL) { |
| printk(KERN_ERR PFX "Aperture out of bounds\n"); |
| return 0; |
| } |
| if (e820_any_mapped(aper, aper + size, E820_RAM)) { |
| printk(KERN_ERR PFX "Aperture pointing to RAM\n"); |
| return 0; |
| } |
| |
| /* Request the Aperture. This catches cases when someone else |
| already put a mapping in there - happens with some very broken BIOS |
| |
| Maybe better to use pci_assign_resource/pci_enable_device instead |
| trusting the bridges? */ |
| if (!aperture_resource && |
| !(aperture_resource = request_mem_region(aper, size, "aperture"))) { |
| printk(KERN_ERR PFX "Aperture conflicts with PCI mapping.\n"); |
| return 0; |
| } |
| return 1; |
| } |
| |
| /* |
| * W*s centric BIOS sometimes only set up the aperture in the AGP |
| * bridge, not the northbridge. On AMD64 this is handled early |
| * in aperture.c, but when IOMMU is not enabled or we run |
| * on a 32bit kernel this needs to be redone. |
| * Unfortunately it is impossible to fix the aperture here because it's too late |
| * to allocate that much memory. But at least error out cleanly instead of |
| * crashing. |
| */ |
| static __devinit int fix_northbridge(struct pci_dev *nb, struct pci_dev *agp, |
| u16 cap) |
| { |
| u32 aper_low, aper_hi; |
| u64 aper, nb_aper; |
| int order = 0; |
| u32 nb_order, nb_base; |
| u16 apsize; |
| |
| pci_read_config_dword(nb, 0x90, &nb_order); |
| nb_order = (nb_order >> 1) & 7; |
| pci_read_config_dword(nb, 0x94, &nb_base); |
| nb_aper = nb_base << 25; |
| if (aperture_valid(nb_aper, (32*1024*1024)<<nb_order)) { |
| return 0; |
| } |
| |
| /* Northbridge seems to contain crap. Try the AGP bridge. */ |
| |
| pci_read_config_word(agp, cap+0x14, &apsize); |
| if (apsize == 0xffff) |
| return -1; |
| |
| apsize &= 0xfff; |
| /* Some BIOS use weird encodings not in the AGPv3 table. */ |
| if (apsize & 0xff) |
| apsize |= 0xf00; |
| order = 7 - hweight16(apsize); |
| |
| pci_read_config_dword(agp, 0x10, &aper_low); |
| pci_read_config_dword(agp, 0x14, &aper_hi); |
| aper = (aper_low & ~((1<<22)-1)) | ((u64)aper_hi << 32); |
| printk(KERN_INFO PFX "Aperture from AGP @ %Lx size %u MB\n", aper, 32 << order); |
| if (order < 0 || !aperture_valid(aper, (32*1024*1024)<<order)) |
| return -1; |
| |
| pci_write_config_dword(nb, 0x90, order << 1); |
| pci_write_config_dword(nb, 0x94, aper >> 25); |
| |
| return 0; |
| } |
| |
| static __devinit int cache_nbs (struct pci_dev *pdev, u32 cap_ptr) |
| { |
| int i; |
| |
| if (cache_k8_northbridges() < 0) |
| return -ENODEV; |
| |
| i = 0; |
| for (i = 0; i < num_k8_northbridges; i++) { |
| struct pci_dev *dev = k8_northbridges[i]; |
| if (fix_northbridge(dev, pdev, cap_ptr) < 0) { |
| printk(KERN_ERR PFX "No usable aperture found.\n"); |
| #ifdef __x86_64__ |
| /* should port this to i386 */ |
| printk(KERN_ERR PFX "Consider rebooting with iommu=memaper=2 to get a good aperture.\n"); |
| #endif |
| return -1; |
| } |
| } |
| return 0; |
| } |
| |
| /* Handle AMD 8151 quirks */ |
| static void __devinit amd8151_init(struct pci_dev *pdev, struct agp_bridge_data *bridge) |
| { |
| char *revstring; |
| |
| switch (pdev->revision) { |
| case 0x01: revstring="A0"; break; |
| case 0x02: revstring="A1"; break; |
| case 0x11: revstring="B0"; break; |
| case 0x12: revstring="B1"; break; |
| case 0x13: revstring="B2"; break; |
| case 0x14: revstring="B3"; break; |
| default: revstring="??"; break; |
| } |
| |
| printk (KERN_INFO PFX "Detected AMD 8151 AGP Bridge rev %s\n", revstring); |
| |
| /* |
| * Work around errata. |
| * Chips before B2 stepping incorrectly reporting v3.5 |
| */ |
| if (pdev->revision < 0x13) { |
| printk (KERN_INFO PFX "Correcting AGP revision (reports 3.5, is really 3.0)\n"); |
| bridge->major_version = 3; |
| bridge->minor_version = 0; |
| } |
| } |
| |
| |
| static const struct aper_size_info_32 uli_sizes[7] = |
| { |
| {256, 65536, 6, 10}, |
| {128, 32768, 5, 9}, |
| {64, 16384, 4, 8}, |
| {32, 8192, 3, 7}, |
| {16, 4096, 2, 6}, |
| {8, 2048, 1, 4}, |
| {4, 1024, 0, 3} |
| }; |
| static int __devinit uli_agp_init(struct pci_dev *pdev) |
| { |
| u32 httfea,baseaddr,enuscr; |
| struct pci_dev *dev1; |
| int i; |
| unsigned size = amd64_fetch_size(); |
| printk(KERN_INFO "Setting up ULi AGP.\n"); |
| dev1 = pci_get_slot (pdev->bus,PCI_DEVFN(0,0)); |
| if (dev1 == NULL) { |
| printk(KERN_INFO PFX "Detected a ULi chipset, " |
| "but could not fine the secondary device.\n"); |
| return -ENODEV; |
| } |
| |
| for (i = 0; i < ARRAY_SIZE(uli_sizes); i++) |
| if (uli_sizes[i].size == size) |
| break; |
| |
| if (i == ARRAY_SIZE(uli_sizes)) { |
| printk(KERN_INFO PFX "No ULi size found for %d\n", size); |
| return -ENODEV; |
| } |
| |
| /* shadow x86-64 registers into ULi registers */ |
| pci_read_config_dword (k8_northbridges[0], AMD64_GARTAPERTUREBASE, &httfea); |
| |
| /* if x86-64 aperture base is beyond 4G, exit here */ |
| if ((httfea & 0x7fff) >> (32 - 25)) |
| return -ENODEV; |
| |
| httfea = (httfea& 0x7fff) << 25; |
| |
| pci_read_config_dword(pdev, ULI_X86_64_BASE_ADDR, &baseaddr); |
| baseaddr&= ~PCI_BASE_ADDRESS_MEM_MASK; |
| baseaddr|= httfea; |
| pci_write_config_dword(pdev, ULI_X86_64_BASE_ADDR, baseaddr); |
| |
| enuscr= httfea+ (size * 1024 * 1024) - 1; |
| pci_write_config_dword(dev1, ULI_X86_64_HTT_FEA_REG, httfea); |
| pci_write_config_dword(dev1, ULI_X86_64_ENU_SCR_REG, enuscr); |
| |
| pci_dev_put(dev1); |
| return 0; |
| } |
| |
| |
| static const struct aper_size_info_32 nforce3_sizes[5] = |
| { |
| {512, 131072, 7, 0x00000000 }, |
| {256, 65536, 6, 0x00000008 }, |
| {128, 32768, 5, 0x0000000C }, |
| {64, 16384, 4, 0x0000000E }, |
| {32, 8192, 3, 0x0000000F } |
| }; |
| |
| /* Handle shadow device of the Nvidia NForce3 */ |
| /* CHECK-ME original 2.4 version set up some IORRs. Check if that is needed. */ |
| static int nforce3_agp_init(struct pci_dev *pdev) |
| { |
| u32 tmp, apbase, apbar, aplimit; |
| struct pci_dev *dev1; |
| int i; |
| unsigned size = amd64_fetch_size(); |
| |
| printk(KERN_INFO PFX "Setting up Nforce3 AGP.\n"); |
| |
| dev1 = pci_get_slot(pdev->bus, PCI_DEVFN(11, 0)); |
| if (dev1 == NULL) { |
| printk(KERN_INFO PFX "agpgart: Detected an NVIDIA " |
| "nForce3 chipset, but could not find " |
| "the secondary device.\n"); |
| return -ENODEV; |
| } |
| |
| for (i = 0; i < ARRAY_SIZE(nforce3_sizes); i++) |
| if (nforce3_sizes[i].size == size) |
| break; |
| |
| if (i == ARRAY_SIZE(nforce3_sizes)) { |
| printk(KERN_INFO PFX "No NForce3 size found for %d\n", size); |
| return -ENODEV; |
| } |
| |
| pci_read_config_dword(dev1, NVIDIA_X86_64_1_APSIZE, &tmp); |
| tmp &= ~(0xf); |
| tmp |= nforce3_sizes[i].size_value; |
| pci_write_config_dword(dev1, NVIDIA_X86_64_1_APSIZE, tmp); |
| |
| /* shadow x86-64 registers into NVIDIA registers */ |
| pci_read_config_dword (k8_northbridges[0], AMD64_GARTAPERTUREBASE, &apbase); |
| |
| /* if x86-64 aperture base is beyond 4G, exit here */ |
| if ( (apbase & 0x7fff) >> (32 - 25) ) { |
| printk(KERN_INFO PFX "aperture base > 4G\n"); |
| return -ENODEV; |
| } |
| |
| apbase = (apbase & 0x7fff) << 25; |
| |
| pci_read_config_dword(pdev, NVIDIA_X86_64_0_APBASE, &apbar); |
| apbar &= ~PCI_BASE_ADDRESS_MEM_MASK; |
| apbar |= apbase; |
| pci_write_config_dword(pdev, NVIDIA_X86_64_0_APBASE, apbar); |
| |
| aplimit = apbase + (size * 1024 * 1024) - 1; |
| pci_write_config_dword(dev1, NVIDIA_X86_64_1_APBASE1, apbase); |
| pci_write_config_dword(dev1, NVIDIA_X86_64_1_APLIMIT1, aplimit); |
| pci_write_config_dword(dev1, NVIDIA_X86_64_1_APBASE2, apbase); |
| pci_write_config_dword(dev1, NVIDIA_X86_64_1_APLIMIT2, aplimit); |
| |
| pci_dev_put(dev1); |
| |
| return 0; |
| } |
| |
| static int __devinit agp_amd64_probe(struct pci_dev *pdev, |
| const struct pci_device_id *ent) |
| { |
| struct agp_bridge_data *bridge; |
| u8 cap_ptr; |
| |
| cap_ptr = pci_find_capability(pdev, PCI_CAP_ID_AGP); |
| if (!cap_ptr) |
| return -ENODEV; |
| |
| /* Could check for AGPv3 here */ |
| |
| bridge = agp_alloc_bridge(); |
| if (!bridge) |
| return -ENOMEM; |
| |
| if (pdev->vendor == PCI_VENDOR_ID_AMD && |
| pdev->device == PCI_DEVICE_ID_AMD_8151_0) { |
| amd8151_init(pdev, bridge); |
| } else { |
| printk(KERN_INFO PFX "Detected AGP bridge %x\n", pdev->devfn); |
| } |
| |
| bridge->driver = &amd_8151_driver; |
| bridge->dev = pdev; |
| bridge->capndx = cap_ptr; |
| |
| /* Fill in the mode register */ |
| pci_read_config_dword(pdev, bridge->capndx+PCI_AGP_STATUS, &bridge->mode); |
| |
| if (cache_nbs(pdev, cap_ptr) == -1) { |
| agp_put_bridge(bridge); |
| return -ENODEV; |
| } |
| |
| if (pdev->vendor == PCI_VENDOR_ID_NVIDIA) { |
| int ret = nforce3_agp_init(pdev); |
| if (ret) { |
| agp_put_bridge(bridge); |
| return ret; |
| } |
| } |
| |
| if (pdev->vendor == PCI_VENDOR_ID_AL) { |
| int ret = uli_agp_init(pdev); |
| if (ret) { |
| agp_put_bridge(bridge); |
| return ret; |
| } |
| } |
| |
| pci_set_drvdata(pdev, bridge); |
| return agp_add_bridge(bridge); |
| } |
| |
| static void __devexit agp_amd64_remove(struct pci_dev *pdev) |
| { |
| struct agp_bridge_data *bridge = pci_get_drvdata(pdev); |
| |
| release_mem_region(virt_to_gart(bridge->gatt_table_real), |
| amd64_aperture_sizes[bridge->aperture_size_idx].size); |
| agp_remove_bridge(bridge); |
| agp_put_bridge(bridge); |
| } |
| |
| #ifdef CONFIG_PM |
| |
| static int agp_amd64_suspend(struct pci_dev *pdev, pm_message_t state) |
| { |
| pci_save_state(pdev); |
| pci_set_power_state(pdev, pci_choose_state(pdev, state)); |
| |
| return 0; |
| } |
| |
| static int agp_amd64_resume(struct pci_dev *pdev) |
| { |
| pci_set_power_state(pdev, PCI_D0); |
| pci_restore_state(pdev); |
| |
| if (pdev->vendor == PCI_VENDOR_ID_NVIDIA) |
| nforce3_agp_init(pdev); |
| |
| return amd_8151_configure(); |
| } |
| |
| #endif /* CONFIG_PM */ |
| |
| static struct pci_device_id agp_amd64_pci_table[] = { |
| { |
| .class = (PCI_CLASS_BRIDGE_HOST << 8), |
| .class_mask = ~0, |
| .vendor = PCI_VENDOR_ID_AMD, |
| .device = PCI_DEVICE_ID_AMD_8151_0, |
| .subvendor = PCI_ANY_ID, |
| .subdevice = PCI_ANY_ID, |
| }, |
| /* ULi M1689 */ |
| { |
| .class = (PCI_CLASS_BRIDGE_HOST << 8), |
| .class_mask = ~0, |
| .vendor = PCI_VENDOR_ID_AL, |
| .device = PCI_DEVICE_ID_AL_M1689, |
| .subvendor = PCI_ANY_ID, |
| .subdevice = PCI_ANY_ID, |
| }, |
| /* VIA K8T800Pro */ |
| { |
| .class = (PCI_CLASS_BRIDGE_HOST << 8), |
| .class_mask = ~0, |
| .vendor = PCI_VENDOR_ID_VIA, |
| .device = PCI_DEVICE_ID_VIA_K8T800PRO_0, |
| .subvendor = PCI_ANY_ID, |
| .subdevice = PCI_ANY_ID, |
| }, |
| /* VIA K8T800 */ |
| { |
| .class = (PCI_CLASS_BRIDGE_HOST << 8), |
| .class_mask = ~0, |
| .vendor = PCI_VENDOR_ID_VIA, |
| .device = PCI_DEVICE_ID_VIA_8385_0, |
| .subvendor = PCI_ANY_ID, |
| .subdevice = PCI_ANY_ID, |
| }, |
| /* VIA K8M800 / K8N800 */ |
| { |
| .class = (PCI_CLASS_BRIDGE_HOST << 8), |
| .class_mask = ~0, |
| .vendor = PCI_VENDOR_ID_VIA, |
| .device = PCI_DEVICE_ID_VIA_8380_0, |
| .subvendor = PCI_ANY_ID, |
| .subdevice = PCI_ANY_ID, |
| }, |
| /* VIA K8M890 / K8N890 */ |
| { |
| .class = (PCI_CLASS_BRIDGE_HOST << 8), |
| .class_mask = ~0, |
| .vendor = PCI_VENDOR_ID_VIA, |
| .device = PCI_DEVICE_ID_VIA_VT3336, |
| .subvendor = PCI_ANY_ID, |
| .subdevice = PCI_ANY_ID, |
| }, |
| /* VIA K8T890 */ |
| { |
| .class = (PCI_CLASS_BRIDGE_HOST << 8), |
| .class_mask = ~0, |
| .vendor = PCI_VENDOR_ID_VIA, |
| .device = PCI_DEVICE_ID_VIA_3238_0, |
| .subvendor = PCI_ANY_ID, |
| .subdevice = PCI_ANY_ID, |
| }, |
| /* VIA K8T800/K8M800/K8N800 */ |
| { |
| .class = (PCI_CLASS_BRIDGE_HOST << 8), |
| .class_mask = ~0, |
| .vendor = PCI_VENDOR_ID_VIA, |
| .device = PCI_DEVICE_ID_VIA_838X_1, |
| .subvendor = PCI_ANY_ID, |
| .subdevice = PCI_ANY_ID, |
| }, |
| /* NForce3 */ |
| { |
| .class = (PCI_CLASS_BRIDGE_HOST << 8), |
| .class_mask = ~0, |
| .vendor = PCI_VENDOR_ID_NVIDIA, |
| .device = PCI_DEVICE_ID_NVIDIA_NFORCE3, |
| .subvendor = PCI_ANY_ID, |
| .subdevice = PCI_ANY_ID, |
| }, |
| { |
| .class = (PCI_CLASS_BRIDGE_HOST << 8), |
| .class_mask = ~0, |
| .vendor = PCI_VENDOR_ID_NVIDIA, |
| .device = PCI_DEVICE_ID_NVIDIA_NFORCE3S, |
| .subvendor = PCI_ANY_ID, |
| .subdevice = PCI_ANY_ID, |
| }, |
| /* SIS 755 */ |
| { |
| .class = (PCI_CLASS_BRIDGE_HOST << 8), |
| .class_mask = ~0, |
| .vendor = PCI_VENDOR_ID_SI, |
| .device = PCI_DEVICE_ID_SI_755, |
| .subvendor = PCI_ANY_ID, |
| .subdevice = PCI_ANY_ID, |
| }, |
| /* SIS 760 */ |
| { |
| .class = (PCI_CLASS_BRIDGE_HOST << 8), |
| .class_mask = ~0, |
| .vendor = PCI_VENDOR_ID_SI, |
| .device = PCI_DEVICE_ID_SI_760, |
| .subvendor = PCI_ANY_ID, |
| .subdevice = PCI_ANY_ID, |
| }, |
| /* ALI/ULI M1695 */ |
| { |
| .class = (PCI_CLASS_BRIDGE_HOST << 8), |
| .class_mask = ~0, |
| .vendor = PCI_VENDOR_ID_AL, |
| .device = 0x1695, |
| .subvendor = PCI_ANY_ID, |
| .subdevice = PCI_ANY_ID, |
| }, |
| |
| { } |
| }; |
| |
| MODULE_DEVICE_TABLE(pci, agp_amd64_pci_table); |
| |
| static struct pci_driver agp_amd64_pci_driver = { |
| .name = "agpgart-amd64", |
| .id_table = agp_amd64_pci_table, |
| .probe = agp_amd64_probe, |
| .remove = agp_amd64_remove, |
| #ifdef CONFIG_PM |
| .suspend = agp_amd64_suspend, |
| .resume = agp_amd64_resume, |
| #endif |
| }; |
| |
| |
| /* Not static due to IOMMU code calling it early. */ |
| int __init agp_amd64_init(void) |
| { |
| int err = 0; |
| |
| if (agp_off) |
| return -EINVAL; |
| if (pci_register_driver(&agp_amd64_pci_driver) < 0) { |
| struct pci_dev *dev; |
| if (!agp_try_unsupported && !agp_try_unsupported_boot) { |
| printk(KERN_INFO PFX "No supported AGP bridge found.\n"); |
| #ifdef MODULE |
| printk(KERN_INFO PFX "You can try agp_try_unsupported=1\n"); |
| #else |
| printk(KERN_INFO PFX "You can boot with agp=try_unsupported\n"); |
| #endif |
| return -ENODEV; |
| } |
| |
| /* First check that we have at least one AMD64 NB */ |
| if (!pci_dev_present(k8_nb_ids)) |
| return -ENODEV; |
| |
| /* Look for any AGP bridge */ |
| dev = NULL; |
| err = -ENODEV; |
| for_each_pci_dev(dev) { |
| if (!pci_find_capability(dev, PCI_CAP_ID_AGP)) |
| continue; |
| /* Only one bridge supported right now */ |
| if (agp_amd64_probe(dev, NULL) == 0) { |
| err = 0; |
| break; |
| } |
| } |
| } |
| return err; |
| } |
| |
| static void __exit agp_amd64_cleanup(void) |
| { |
| if (aperture_resource) |
| release_resource(aperture_resource); |
| pci_unregister_driver(&agp_amd64_pci_driver); |
| } |
| |
| /* On AMD64 the PCI driver needs to initialize this driver early |
| for the IOMMU, so it has to be called via a backdoor. */ |
| #ifndef CONFIG_GART_IOMMU |
| module_init(agp_amd64_init); |
| module_exit(agp_amd64_cleanup); |
| #endif |
| |
| MODULE_AUTHOR("Dave Jones <davej@codemonkey.org.uk>, Andi Kleen"); |
| module_param(agp_try_unsupported, bool, 0); |
| MODULE_LICENSE("GPL"); |