| /* |
| * H2W device detection driver. |
| * |
| * Copyright (C) 2008 Google, Inc. |
| * Copyright (C) 2008 HTC, Inc. |
| * |
| * Authors: |
| * Laurence Chen <Laurence_Chen@htc.com> |
| * Nick Pelly <npelly@google.com> |
| * Thomas Tsai <thomas_tsai@htc.com> |
| * Farmer Tseng <farmer_tseng@htc.com> |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License as published by |
| * the Free Software Foundation; version 2 of the License. |
| */ |
| |
| /* For detecting HTC 2 Wire devices, such as wired headset. |
| |
| Logically, the H2W driver is always present, and H2W state (hi->state) |
| indicates what is currently plugged into the H2W interface. |
| |
| When the headset is plugged in, CABLE_IN1 is pulled low. When the headset |
| button is pressed, CABLE_IN2 is pulled low. These two lines are shared with |
| the TX and RX (respectively) of UART3 - used for serial debugging. |
| |
| This headset driver keeps the CPLD configured as UART3 for as long as |
| possible, so that we can do serial FIQ debugging even when the kernel is |
| locked and this driver no longer runs. So it only configures the CPLD to |
| GPIO while the headset is plugged in, and for 10ms during detection work. |
| |
| Unfortunately we can't leave the CPLD as UART3 while a headset is plugged |
| in, UART3 is pullup on TX but the headset is pull-down, causing a 55 mA |
| drain on trout. |
| |
| The headset detection work involves setting CPLD to GPIO, and then pulling |
| CABLE_IN1 high with a stronger pullup than usual. A H2W headset will still |
| pull this line low, whereas other attachments such as a serial console |
| would get pulled up by this stronger pullup. |
| |
| Headset insertion/removal causes UEvent's to be sent, and |
| /sys/class/switch/h2w/state to be updated. |
| |
| Button presses are interpreted as input event (KEY_MEDIA). Button presses |
| are ignored if the headset is plugged in, so the buttons on 11 pin -> 3.5mm |
| jack adapters do not work until a headset is plugged into the adapter. This |
| is to avoid serial RX traffic causing spurious button press events. |
| |
| We tend to check the status of CABLE_IN1 a few more times than strictly |
| necessary during headset detection, to avoid spurious headset insertion |
| events caused by serial debugger TX traffic. |
| */ |
| |
| #include <linux/module.h> |
| #include <linux/sysdev.h> |
| #include <linux/fs.h> |
| #include <linux/interrupt.h> |
| #include <linux/workqueue.h> |
| #include <linux/irq.h> |
| #include <linux/delay.h> |
| #include <linux/types.h> |
| #include <linux/input.h> |
| #include <linux/platform_device.h> |
| #include <linux/mutex.h> |
| #include <linux/errno.h> |
| #include <linux/err.h> |
| #include <linux/hrtimer.h> |
| #include <linux/switch.h> |
| #include <linux/input.h> |
| #include <linux/debugfs.h> |
| #include <asm/gpio.h> |
| #include <asm/atomic.h> |
| #include <mach/board.h> |
| #include <mach/vreg.h> |
| #include <asm/mach-types.h> |
| |
| #include <mach/htc_headset.h> |
| |
| #define H2WI(fmt, arg...) \ |
| printk(KERN_INFO "[H2W] %s " fmt "\r\n", __func__, ## arg) |
| #define H2WE(fmt, arg...) \ |
| printk(KERN_ERR "[H2W] %s " fmt "\r\n", __func__, ## arg) |
| |
| #ifdef CONFIG_DEBUG_H2W |
| #define H2W_DBG(fmt, arg...) printk(KERN_INFO "[H2W] %s " fmt "\r\n", __func__, ## arg) |
| #else |
| #define H2W_DBG(fmt, arg...) do {} while (0) |
| #endif |
| |
| static struct workqueue_struct *g_detection_work_queue; |
| static void detection_work(struct work_struct *work); |
| static DECLARE_WORK(g_detection_work, detection_work); |
| |
| struct h2w_info { |
| struct switch_dev sdev; |
| struct input_dev *input; |
| struct mutex mutex_lock; |
| |
| atomic_t btn_state; |
| int ignore_btn; |
| |
| unsigned int irq; |
| unsigned int irq_btn; |
| |
| int cable_in1; |
| int cable_in2; |
| int h2w_clk; |
| int h2w_data; |
| int debug_uart; |
| |
| void (*config_cpld) (int); |
| void (*init_cpld) (void); |
| /* for h2w */ |
| void (*set_dat)(int); |
| void (*set_clk)(int); |
| void (*set_dat_dir)(int); |
| void (*set_clk_dir)(int); |
| int (*get_dat)(void); |
| int (*get_clk)(void); |
| |
| int htc_headset_flag; |
| |
| struct hrtimer timer; |
| ktime_t debounce_time; |
| |
| struct hrtimer btn_timer; |
| ktime_t btn_debounce_time; |
| |
| H2W_INFO h2w_info; |
| H2W_SPEED speed; |
| struct vreg *vreg_h2w; |
| }; |
| static struct h2w_info *hi; |
| |
| static ssize_t h2w_print_name(struct switch_dev *sdev, char *buf) |
| { |
| switch (switch_get_state(&hi->sdev)) { |
| case H2W_NO_DEVICE: |
| return sprintf(buf, "No Device\n"); |
| case H2W_HTC_HEADSET: |
| return sprintf(buf, "Headset\n"); |
| } |
| return -EINVAL; |
| } |
| |
| static void button_pressed(void) |
| { |
| H2W_DBG("button_pressed \n"); |
| atomic_set(&hi->btn_state, 1); |
| input_report_key(hi->input, KEY_MEDIA, 1); |
| input_sync(hi->input); |
| } |
| |
| static void button_released(void) |
| { |
| H2W_DBG("button_released \n"); |
| atomic_set(&hi->btn_state, 0); |
| input_report_key(hi->input, KEY_MEDIA, 0); |
| input_sync(hi->input); |
| } |
| |
| /***************** |
| * H2W proctocol * |
| *****************/ |
| static inline void h2w_begin_command(void) |
| { |
| /* Disable H2W interrupt */ |
| set_irq_type(hi->irq_btn, IRQF_TRIGGER_HIGH); |
| disable_irq(hi->irq); |
| disable_irq(hi->irq_btn); |
| |
| /* Set H2W_CLK as output low */ |
| hi->set_clk(0); |
| hi->set_clk_dir(1); |
| } |
| |
| static inline void h2w_end_command(void) |
| { |
| /* Set H2W_CLK as input */ |
| hi->set_clk_dir(0); |
| |
| /* Enable H2W interrupt */ |
| enable_irq(hi->irq); |
| enable_irq(hi->irq_btn); |
| set_irq_type(hi->irq_btn, IRQF_TRIGGER_RISING); |
| } |
| |
| /* |
| * One bit write data |
| * ________ |
| * SCLK O ______| |______O(L) |
| * |
| * |
| * SDAT I <XXXXXXXXXXXXXXXXXXXX> |
| */ |
| static inline void one_clock_write(unsigned short flag) |
| { |
| if (flag) |
| hi->set_dat(1); |
| else |
| hi->set_dat(0); |
| |
| udelay(hi->speed); |
| hi->set_clk(1); |
| udelay(hi->speed); |
| hi->set_clk(0); |
| } |
| |
| /* |
| * One bit write data R/W bit |
| * ________ |
| * SCLK ______| |______O(L) |
| * 1----> 1-----> |
| * 2-------> ______ |
| * SDAT <XXXXXXXXXXXXXX> I |
| * O(H/L) |
| */ |
| static inline void one_clock_write_RWbit(unsigned short flag) |
| { |
| if (flag) |
| hi->set_dat(1); |
| else |
| hi->set_dat(0); |
| |
| udelay(hi->speed); |
| hi->set_clk(1); |
| udelay(hi->speed); |
| hi->set_clk(0); |
| hi->set_dat_dir(0); |
| udelay(hi->speed); |
| } |
| |
| /* |
| * H2W Reset |
| * ___________ |
| * SCLK O(L)______| |___O(L) |
| * 1----> |
| * 4-->1-->1-->1us--> |
| * ____ |
| * SDAT O(L)________ | |_______O(L) |
| * |
| * H2w reset command needs to be issued before every access |
| */ |
| static inline void h2w_reset(void) |
| { |
| /* Set H2W_DAT as output low */ |
| hi->set_dat(0); |
| hi->set_dat_dir(1); |
| |
| udelay(hi->speed); |
| hi->set_clk(1); |
| udelay(4 * hi->speed); |
| hi->set_dat(1); |
| udelay(hi->speed); |
| hi->set_dat(0); |
| udelay(hi->speed); |
| hi->set_clk(0); |
| udelay(hi->speed); |
| } |
| |
| /* |
| * H2W Start |
| * ___________ |
| * SCLK O(L)______| |___O(L) |
| * 1----> |
| * 2----------->1--> |
| * |
| * SDAT O(L)______________________O(L) |
| */ |
| static inline void h2w_start(void) |
| { |
| udelay(hi->speed); |
| hi->set_clk(1); |
| udelay(2 * hi->speed); |
| hi->set_clk(0); |
| udelay(hi->speed); |
| } |
| |
| /* |
| * H2W Ack |
| * __________ |
| * SCLK _____| |_______O(L) |
| * 1----> 1------> |
| * 2---------> |
| * ________________________ |
| * SDAT become Input mode here I |
| */ |
| static inline int h2w_ack(void) |
| { |
| int retry_times = 0; |
| |
| ack_resend: |
| if (retry_times == MAX_ACK_RESEND_TIMES) |
| return -1; |
| |
| udelay(hi->speed); |
| hi->set_clk(1); |
| udelay(2 * hi->speed); |
| |
| if (!hi->get_dat()) { |
| retry_times++; |
| hi->set_clk(0); |
| udelay(hi->speed); |
| goto ack_resend; |
| } |
| |
| hi->set_clk(0); |
| udelay(hi->speed); |
| return 0; |
| } |
| |
| /* |
| * One bit read data |
| * ________ |
| * SCLK ______| |______O(L) |
| * 2----> 2-----> |
| * 2-------> |
| * SDAT <XXXXXXXXXXXXXXXXXXXX>I |
| */ |
| static unsigned char h2w_readc(void) |
| { |
| unsigned char h2w_read_data = 0x0; |
| int index; |
| |
| for (index = 0; index < 8; index++) { |
| hi->set_clk(0); |
| udelay(hi->speed); |
| hi->set_clk(1); |
| udelay(hi->speed); |
| if (hi->get_dat()) |
| h2w_read_data |= (1 << (7 - index)); |
| } |
| hi->set_clk(0); |
| udelay(hi->speed); |
| |
| return h2w_read_data; |
| } |
| |
| static int h2w_readc_cmd(H2W_ADDR address) |
| { |
| int ret = -1, retry_times = 0; |
| unsigned char read_data; |
| |
| read_resend: |
| if (retry_times == MAX_HOST_RESEND_TIMES) |
| goto err_read; |
| |
| h2w_reset(); |
| h2w_start(); |
| /* Write address */ |
| one_clock_write(address & 0x1000); |
| one_clock_write(address & 0x0800); |
| one_clock_write(address & 0x0400); |
| one_clock_write(address & 0x0200); |
| one_clock_write(address & 0x0100); |
| one_clock_write(address & 0x0080); |
| one_clock_write(address & 0x0040); |
| one_clock_write(address & 0x0020); |
| one_clock_write(address & 0x0010); |
| one_clock_write(address & 0x0008); |
| one_clock_write(address & 0x0004); |
| one_clock_write(address & 0x0002); |
| one_clock_write(address & 0x0001); |
| one_clock_write_RWbit(1); |
| if (h2w_ack() < 0) { |
| H2W_DBG("Addr NO ACK(%d).\n", retry_times); |
| retry_times++; |
| hi->set_clk(0); |
| mdelay(RESEND_DELAY); |
| goto read_resend; |
| } |
| |
| read_data = h2w_readc(); |
| |
| if (h2w_ack() < 0) { |
| H2W_DBG("Data NO ACK(%d).\n", retry_times); |
| retry_times++; |
| hi->set_clk(0); |
| mdelay(RESEND_DELAY); |
| goto read_resend; |
| } |
| ret = (int)read_data; |
| |
| err_read: |
| if (ret < 0) |
| H2WE("NO ACK.\n"); |
| |
| return ret; |
| } |
| |
| static int h2w_writec_cmd(H2W_ADDR address, unsigned char data) |
| { |
| int ret = -1; |
| int retry_times = 0; |
| |
| write_resend: |
| if (retry_times == MAX_HOST_RESEND_TIMES) |
| goto err_write; |
| |
| h2w_reset(); |
| h2w_start(); |
| |
| /* Write address */ |
| one_clock_write(address & 0x1000); |
| one_clock_write(address & 0x0800); |
| one_clock_write(address & 0x0400); |
| one_clock_write(address & 0x0200); |
| one_clock_write(address & 0x0100); |
| one_clock_write(address & 0x0080); |
| one_clock_write(address & 0x0040); |
| one_clock_write(address & 0x0020); |
| one_clock_write(address & 0x0010); |
| one_clock_write(address & 0x0008); |
| one_clock_write(address & 0x0004); |
| one_clock_write(address & 0x0002); |
| one_clock_write(address & 0x0001); |
| one_clock_write_RWbit(0); |
| if (h2w_ack() < 0) { |
| H2W_DBG("Addr NO ACK(%d).\n", retry_times); |
| retry_times++; |
| hi->set_clk(0); |
| mdelay(RESEND_DELAY); |
| goto write_resend; |
| } |
| |
| /* Write data */ |
| hi->set_dat_dir(1); |
| one_clock_write(data & 0x0080); |
| one_clock_write(data & 0x0040); |
| one_clock_write(data & 0x0020); |
| one_clock_write(data & 0x0010); |
| one_clock_write(data & 0x0008); |
| one_clock_write(data & 0x0004); |
| one_clock_write(data & 0x0002); |
| one_clock_write_RWbit(data & 0x0001); |
| if (h2w_ack() < 0) { |
| H2W_DBG("Data NO ACK(%d).\n", retry_times); |
| retry_times++; |
| hi->set_clk(0); |
| mdelay(RESEND_DELAY); |
| goto write_resend; |
| } |
| ret = 0; |
| |
| err_write: |
| if (ret < 0) |
| H2WE("NO ACK.\n"); |
| |
| return ret; |
| } |
| |
| static int h2w_get_fnkey(void) |
| { |
| int ret; |
| h2w_begin_command(); |
| ret = h2w_readc_cmd(H2W_FNKEY_UPDOWN); |
| h2w_end_command(); |
| return ret; |
| } |
| |
| static int h2w_dev_init(H2W_INFO *ph2w_info) |
| { |
| int ret = -1; |
| unsigned char ascr0 = 0; |
| int h2w_sys = 0, maxgpadd = 0, maxadd = 0, key = 0; |
| |
| hi->speed = H2W_50KHz; |
| h2w_begin_command(); |
| |
| /* read H2W_SYSTEM */ |
| h2w_sys = h2w_readc_cmd(H2W_SYSTEM); |
| if (h2w_sys == -1) { |
| H2WE("read H2W_SYSTEM(0x0000) failed.\n"); |
| goto err_plugin; |
| } |
| ph2w_info->ACC_CLASS = (h2w_sys & 0x03); |
| ph2w_info->AUDIO_DEVICE = (h2w_sys & 0x04) > 0 ? 1 : 0; |
| ph2w_info->HW_REV = (h2w_sys & 0x18) >> 3; |
| ph2w_info->SLEEP_PR = (h2w_sys & 0x20) >> 5; |
| ph2w_info->CLK_SP = (h2w_sys & 0xC0) >> 6; |
| |
| /* enter init mode */ |
| if (h2w_writec_cmd(H2W_ASCR0, H2W_ASCR_DEVICE_INI) < 0) { |
| H2WE("write H2W_ASCR0(0x0002) failed.\n"); |
| goto err_plugin; |
| } |
| udelay(10); |
| |
| /* read H2W_MAX_GP_ADD */ |
| maxgpadd = h2w_readc_cmd(H2W_MAX_GP_ADD); |
| if (maxgpadd == -1) { |
| H2WE("write H2W_MAX_GP_ADD(0x0001) failed.\n"); |
| goto err_plugin; |
| } |
| ph2w_info->CLK_SP += (maxgpadd & 0x60) >> 3; |
| ph2w_info->MAX_GP_ADD = (maxgpadd & 0x1F); |
| |
| /* read key group */ |
| if (ph2w_info->MAX_GP_ADD >= 1) { |
| ph2w_info->KEY_MAXADD = h2w_readc_cmd(H2W_KEY_MAXADD); |
| if (ph2w_info->KEY_MAXADD == -1) |
| goto err_plugin; |
| if (ph2w_info->KEY_MAXADD >= 1) { |
| key = h2w_readc_cmd(H2W_ASCII_DOWN); |
| if (key < 0) |
| goto err_plugin; |
| ph2w_info->ASCII_DOWN = (key == 0xFF) ? 1 : 0; |
| } |
| if (ph2w_info->KEY_MAXADD >= 2) { |
| key = h2w_readc_cmd(H2W_ASCII_UP); |
| if (key == -1) |
| goto err_plugin; |
| ph2w_info->ASCII_UP = (key == 0xFF) ? 1 : 0; |
| } |
| if (ph2w_info->KEY_MAXADD >= 3) { |
| key = h2w_readc_cmd(H2W_FNKEY_UPDOWN); |
| if (key == -1) |
| goto err_plugin; |
| ph2w_info->FNKEY_UPDOWN = (key == 0xFF) ? 1 : 0; |
| } |
| if (ph2w_info->KEY_MAXADD >= 4) { |
| key = h2w_readc_cmd(H2W_KD_STATUS); |
| if (key == -1) |
| goto err_plugin; |
| ph2w_info->KD_STATUS = (key == 0x01) ? 1 : 0; |
| } |
| } |
| |
| /* read led group */ |
| if (ph2w_info->MAX_GP_ADD >= 2) { |
| ph2w_info->LED_MAXADD = h2w_readc_cmd(H2W_LED_MAXADD); |
| if (ph2w_info->LED_MAXADD == -1) |
| goto err_plugin; |
| if (ph2w_info->LED_MAXADD >= 1) { |
| key = h2w_readc_cmd(H2W_LEDCT0); |
| if (key == -1) |
| goto err_plugin; |
| ph2w_info->LEDCT0 = (key == 0x02) ? 1 : 0; |
| } |
| } |
| |
| /* read group 3, 4, 5 */ |
| if (ph2w_info->MAX_GP_ADD >= 3) { |
| maxadd = h2w_readc_cmd(H2W_CRDL_MAXADD); |
| if (maxadd == -1) |
| goto err_plugin; |
| } |
| if (ph2w_info->MAX_GP_ADD >= 4) { |
| maxadd = h2w_readc_cmd(H2W_CARKIT_MAXADD); |
| if (maxadd == -1) |
| goto err_plugin; |
| } |
| if (ph2w_info->MAX_GP_ADD >= 5) { |
| maxadd = h2w_readc_cmd(H2W_USBHOST_MAXADD); |
| if (maxadd == -1) |
| goto err_plugin; |
| } |
| |
| /* read medical group */ |
| if (ph2w_info->MAX_GP_ADD >= 6) { |
| ph2w_info->MED_MAXADD = h2w_readc_cmd(H2W_MED_MAXADD); |
| if (ph2w_info->MED_MAXADD == -1) |
| goto err_plugin; |
| if (ph2w_info->MED_MAXADD >= 1) { |
| key = h2w_readc_cmd(H2W_MED_CONTROL); |
| if (key == -1) |
| goto err_plugin; |
| ph2w_info->DATA_EN = (key & 0x01); |
| ph2w_info->AP_EN = (key & 0x02) >> 1; |
| ph2w_info->AP_ID = (key & 0x1c) >> 2; |
| } |
| if (ph2w_info->MED_MAXADD >= 2) { |
| key = h2w_readc_cmd(H2W_MED_IN_DATA); |
| if (key == -1) |
| goto err_plugin; |
| } |
| } |
| |
| if (ph2w_info->AUDIO_DEVICE) |
| ascr0 = H2W_ASCR_AUDIO_IN | H2W_ASCR_ACT_EN; |
| else |
| ascr0 = H2W_ASCR_ACT_EN; |
| |
| if (h2w_writec_cmd(H2W_ASCR0, ascr0) < 0) |
| goto err_plugin; |
| udelay(10); |
| |
| ret = 0; |
| |
| /* adjust speed */ |
| if (ph2w_info->MAX_GP_ADD == 2) { |
| /* Remote control */ |
| hi->speed = H2W_250KHz; |
| } else if (ph2w_info->MAX_GP_ADD == 6) { |
| if (ph2w_info->MED_MAXADD >= 1) { |
| key = h2w_readc_cmd(H2W_MED_CONTROL); |
| if (key == -1) |
| goto err_plugin; |
| ph2w_info->DATA_EN = (key & 0x01); |
| ph2w_info->AP_EN = (key & 0x02) >> 1; |
| ph2w_info->AP_ID = (key & 0x1c) >> 2; |
| } |
| } |
| |
| err_plugin: |
| h2w_end_command(); |
| |
| return ret; |
| } |
| |
| static inline void h2w_dev_power_on(int on) |
| { |
| if (!hi->vreg_h2w) |
| return; |
| |
| if (on) |
| vreg_enable(hi->vreg_h2w); |
| else |
| vreg_disable(hi->vreg_h2w); |
| } |
| |
| static int h2w_dev_detect(void) |
| { |
| int ret = -1; |
| int retry_times; |
| |
| for (retry_times = 5; retry_times; retry_times--) { |
| /* Enable H2W Power */ |
| h2w_dev_power_on(1); |
| msleep(100); |
| memset(&hi->h2w_info, 0, sizeof(H2W_INFO)); |
| if (h2w_dev_init(&hi->h2w_info) < 0) { |
| h2w_dev_power_on(0); |
| msleep(100); |
| } else if (hi->h2w_info.MAX_GP_ADD == 2) { |
| ret = 0; |
| break; |
| } else { |
| printk(KERN_INFO "h2w_detect: detect error(%d)\n" |
| , hi->h2w_info.MAX_GP_ADD); |
| h2w_dev_power_on(0); |
| msleep(100); |
| } |
| printk(KERN_INFO "h2w_detect(%d)\n" |
| , hi->h2w_info.MAX_GP_ADD); |
| } |
| H2W_DBG("h2w_detect:(%d)\n", retry_times); |
| return ret; |
| } |
| |
| static void remove_headset(void) |
| { |
| unsigned long irq_flags; |
| |
| H2W_DBG(""); |
| |
| mutex_lock(&hi->mutex_lock); |
| switch_set_state(&hi->sdev, switch_get_state(&hi->sdev) & |
| ~(BIT_HEADSET | BIT_HEADSET_NO_MIC)); |
| mutex_unlock(&hi->mutex_lock); |
| hi->init_cpld(); |
| |
| /* Disable button */ |
| switch (hi->htc_headset_flag) { |
| case H2W_HTC_HEADSET: |
| local_irq_save(irq_flags); |
| disable_irq(hi->irq_btn); |
| local_irq_restore(irq_flags); |
| |
| if (atomic_read(&hi->btn_state)) |
| button_released(); |
| break; |
| case H2W_DEVICE: |
| h2w_dev_power_on(0); |
| set_irq_type(hi->irq_btn, IRQF_TRIGGER_LOW); |
| disable_irq(hi->irq_btn); |
| /* 10ms (5-15 with 10ms tick) */ |
| hi->btn_debounce_time = ktime_set(0, 10000000); |
| hi->set_clk_dir(0); |
| hi->set_dat_dir(0); |
| break; |
| } |
| |
| hi->htc_headset_flag = 0; |
| hi->debounce_time = ktime_set(0, 100000000); /* 100 ms */ |
| |
| } |
| |
| #ifdef CONFIG_MSM_SERIAL_DEBUGGER |
| extern void msm_serial_debug_enable(int); |
| #endif |
| |
| static void insert_headset(int type) |
| { |
| unsigned long irq_flags; |
| int state; |
| |
| H2W_DBG(""); |
| |
| hi->htc_headset_flag = type; |
| state = BIT_HEADSET | BIT_HEADSET_NO_MIC; |
| |
| state = switch_get_state(&hi->sdev); |
| state &= ~(BIT_HEADSET_NO_MIC | BIT_HEADSET); |
| switch (type) { |
| case H2W_HTC_HEADSET: |
| printk(KERN_INFO "insert_headset H2W_HTC_HEADSET\n"); |
| state |= BIT_HEADSET; |
| hi->ignore_btn = !gpio_get_value(hi->cable_in2); |
| /* Enable button irq */ |
| local_irq_save(irq_flags); |
| enable_irq(hi->irq_btn); |
| local_irq_restore(irq_flags); |
| hi->debounce_time = ktime_set(0, 200000000); /* 20 ms */ |
| break; |
| case H2W_DEVICE: |
| if (h2w_dev_detect() < 0) { |
| printk(KERN_INFO "H2W_DEVICE -- Non detect\n"); |
| remove_headset(); |
| } else { |
| printk(KERN_INFO "H2W_DEVICE -- detect\n"); |
| hi->btn_debounce_time = ktime_set(0, 0); |
| local_irq_save(irq_flags); |
| enable_irq(hi->irq_btn); |
| set_irq_type(hi->irq_btn, IRQF_TRIGGER_RISING); |
| local_irq_restore(irq_flags); |
| state |= BIT_HEADSET; |
| } |
| break; |
| case H2W_USB_CRADLE: |
| state |= BIT_HEADSET_NO_MIC; |
| break; |
| case H2W_UART_DEBUG: |
| hi->config_cpld(hi->debug_uart); |
| printk(KERN_INFO "switch to H2W_UART_DEBUG\n"); |
| default: |
| return; |
| } |
| mutex_lock(&hi->mutex_lock); |
| switch_set_state(&hi->sdev, state); |
| mutex_unlock(&hi->mutex_lock); |
| |
| #ifdef CONFIG_MSM_SERIAL_DEBUGGER |
| msm_serial_debug_enable(false); |
| #endif |
| |
| } |
| #if 0 |
| static void remove_headset(void) |
| { |
| unsigned long irq_flags; |
| |
| H2W_DBG(""); |
| |
| switch_set_state(&hi->sdev, H2W_NO_DEVICE); |
| |
| hi->init_cpld(); |
| |
| /* Disable button */ |
| local_irq_save(irq_flags); |
| disable_irq(hi->irq_btn); |
| local_irq_restore(irq_flags); |
| |
| if (atomic_read(&hi->btn_state)) |
| button_released(); |
| |
| hi->debounce_time = ktime_set(0, 100000000); /* 100 ms */ |
| } |
| #endif |
| static int is_accessary_pluged_in(void) |
| { |
| int type = 0; |
| int clk1 = 0, dat1 = 0, clk2 = 0, dat2 = 0, clk3 = 0, dat3 = 0; |
| |
| /* Step1: save H2W_CLK and H2W_DAT */ |
| /* Delay 10ms for pin stable. */ |
| msleep(10); |
| clk1 = gpio_get_value(hi->h2w_clk); |
| dat1 = gpio_get_value(hi->h2w_data); |
| |
| /* |
| * Step2: set GPIO_CABLE_IN1 as output high and GPIO_CABLE_IN2 as |
| * input |
| */ |
| gpio_direction_output(hi->cable_in1, 1); |
| gpio_direction_input(hi->cable_in2); |
| /* Delay 10ms for pin stable. */ |
| msleep(10); |
| /* Step 3: save H2W_CLK and H2W_DAT */ |
| clk2 = gpio_get_value(hi->h2w_clk); |
| dat2 = gpio_get_value(hi->h2w_data); |
| |
| /* |
| * Step 4: set GPIO_CABLE_IN1 as input and GPIO_CABLE_IN2 as output |
| * high |
| */ |
| gpio_direction_input(hi->cable_in1); |
| gpio_direction_output(hi->cable_in2, 1); |
| /* Delay 10ms for pin stable. */ |
| msleep(10); |
| /* Step 5: save H2W_CLK and H2W_DAT */ |
| clk3 = gpio_get_value(hi->h2w_clk); |
| dat3 = gpio_get_value(hi->h2w_data); |
| |
| /* Step 6: set both GPIO_CABLE_IN1 and GPIO_CABLE_IN2 as input */ |
| gpio_direction_input(hi->cable_in1); |
| gpio_direction_input(hi->cable_in2); |
| |
| H2W_DBG("(%d,%d) (%d,%d) (%d,%d)\n", |
| clk1, dat1, clk2, dat2, clk3, dat3); |
| |
| if ((clk1 == 0) && (dat1 == 1) && |
| (clk2 == 0) && (dat2 == 1) && |
| (clk3 == 0) && (dat3 == 1)) |
| type = H2W_HTC_HEADSET; |
| else if ((clk1 == 0) && (dat1 == 0) && |
| (clk2 == 0) && (dat2 == 0) && |
| (clk3 == 0) && (dat3 == 0)) |
| type = NORMAL_HEARPHONE; |
| else if ((clk1 == 0) && (dat1 == 0) && |
| (clk2 == 1) && (dat2 == 0) && |
| (clk3 == 0) && (dat3 == 1)) |
| type = H2W_DEVICE; |
| else if ((clk1 == 0) && (dat1 == 0) && |
| (clk2 == 1) && (dat2 == 1) && |
| (clk3 == 1) && (dat3 == 1)) |
| type = H2W_USB_CRADLE; |
| else if ((clk1 == 0) && (dat1 == 1) && |
| (clk2 == 1) && (dat2 == 1) && |
| (clk3 == 0) && (dat3 == 1)) |
| type = H2W_UART_DEBUG; |
| else |
| type = H2W_NO_DEVICE; |
| |
| return type; |
| } |
| |
| |
| static void detection_work(struct work_struct *work) |
| { |
| unsigned long irq_flags; |
| int type; |
| |
| H2W_DBG(""); |
| |
| if (gpio_get_value(hi->cable_in1) != 0) { |
| /* Headset not plugged in */ |
| if (switch_get_state(&hi->sdev) != H2W_NO_DEVICE) |
| remove_headset(); |
| return; |
| } |
| |
| /* Something plugged in, lets make sure its a headset */ |
| |
| /* Switch CPLD to GPIO to do detection */ |
| hi->config_cpld(H2W_GPIO); |
| |
| /* Disable headset interrupt while detecting.*/ |
| local_irq_save(irq_flags); |
| disable_irq(hi->irq); |
| local_irq_restore(irq_flags); |
| |
| /* Something plugged in, lets make sure its a headset */ |
| type = is_accessary_pluged_in(); |
| |
| /* Restore IRQs */ |
| local_irq_save(irq_flags); |
| enable_irq(hi->irq); |
| local_irq_restore(irq_flags); |
| |
| insert_headset(type); |
| } |
| |
| static enum hrtimer_restart button_event_timer_func(struct hrtimer *data) |
| { |
| int key, press, keyname, h2w_key = 1; |
| |
| H2W_DBG(""); |
| |
| if (switch_get_state(&hi->sdev) == H2W_HTC_HEADSET) { |
| switch (hi->htc_headset_flag) { |
| case H2W_HTC_HEADSET: |
| if (gpio_get_value(hi->cable_in2)) { |
| if (hi->ignore_btn) |
| hi->ignore_btn = 0; |
| else if (atomic_read(&hi->btn_state)) |
| button_released(); |
| } else { |
| if (!hi->ignore_btn && |
| !atomic_read(&hi->btn_state)) |
| button_pressed(); |
| } |
| break; |
| case H2W_DEVICE: |
| if ((hi->get_dat() == 1) && (hi->get_clk() == 1)) { |
| /* Don't do anything because H2W pull out. */ |
| H2WE("Remote Control pull out.\n"); |
| } else { |
| key = h2w_get_fnkey(); |
| press = (key > 0x7F) ? 0 : 1; |
| keyname = key & 0x7F; |
| /* H2WI("key = %d, press = %d, |
| keyname = %d \n", |
| key, press, keyname); */ |
| switch (keyname) { |
| case H2W_KEY_PLAY: |
| H2WI("H2W_KEY_PLAY"); |
| key = KEY_PLAYPAUSE; |
| break; |
| case H2W_KEY_FORWARD: |
| H2WI("H2W_KEY_FORWARD"); |
| key = KEY_NEXTSONG; |
| break; |
| case H2W_KEY_BACKWARD: |
| H2WI("H2W_KEY_BACKWARD"); |
| key = KEY_PREVIOUSSONG; |
| break; |
| case H2W_KEY_VOLUP: |
| H2WI("H2W_KEY_VOLUP"); |
| key = KEY_VOLUMEUP; |
| break; |
| case H2W_KEY_VOLDOWN: |
| H2WI("H2W_KEY_VOLDOWN"); |
| key = KEY_VOLUMEDOWN; |
| break; |
| case H2W_KEY_PICKUP: |
| H2WI("H2W_KEY_PICKUP"); |
| key = KEY_SEND; |
| break; |
| case H2W_KEY_HANGUP: |
| H2WI("H2W_KEY_HANGUP"); |
| key = KEY_END; |
| break; |
| case H2W_KEY_MUTE: |
| H2WI("H2W_KEY_MUTE"); |
| key = KEY_MUTE; |
| break; |
| case H2W_KEY_HOLD: |
| H2WI("H2W_KEY_HOLD"); |
| break; |
| default: |
| H2WI("default"); |
| h2w_key = 0; |
| } |
| if (h2w_key) { |
| if (press) |
| H2WI("Press\n"); |
| else |
| H2WI("Release\n"); |
| input_report_key(hi->input, key, press); |
| } |
| } |
| break; |
| } /* end switch */ |
| } |
| |
| return HRTIMER_NORESTART; |
| } |
| |
| static enum hrtimer_restart detect_event_timer_func(struct hrtimer *data) |
| { |
| H2W_DBG(""); |
| |
| queue_work(g_detection_work_queue, &g_detection_work); |
| return HRTIMER_NORESTART; |
| } |
| |
| static irqreturn_t detect_irq_handler(int irq, void *dev_id) |
| { |
| int value1, value2; |
| int retry_limit = 10; |
| |
| H2W_DBG(""); |
| set_irq_type(hi->irq_btn, IRQF_TRIGGER_LOW); |
| do { |
| value1 = gpio_get_value(hi->cable_in1); |
| set_irq_type(hi->irq, value1 ? |
| IRQF_TRIGGER_LOW : IRQF_TRIGGER_HIGH); |
| value2 = gpio_get_value(hi->cable_in1); |
| } while (value1 != value2 && retry_limit-- > 0); |
| |
| H2W_DBG("value2 = %d (%d retries), device=%d", |
| value2, (10-retry_limit), switch_get_state(&hi->sdev)); |
| |
| if ((switch_get_state(&hi->sdev) == H2W_NO_DEVICE) ^ value2) { |
| if (switch_get_state(&hi->sdev) == H2W_HTC_HEADSET) |
| hi->ignore_btn = 1; |
| /* Do the rest of the work in timer context */ |
| hrtimer_start(&hi->timer, hi->debounce_time, HRTIMER_MODE_REL); |
| } |
| |
| return IRQ_HANDLED; |
| } |
| |
| static irqreturn_t button_irq_handler(int irq, void *dev_id) |
| { |
| int value1, value2; |
| int retry_limit = 10; |
| |
| H2W_DBG(""); |
| do { |
| value1 = gpio_get_value(hi->cable_in2); |
| if (hi->htc_headset_flag != H2W_DEVICE) |
| set_irq_type(hi->irq_btn, value1 ? |
| IRQF_TRIGGER_LOW : IRQF_TRIGGER_HIGH); |
| value2 = gpio_get_value(hi->cable_in2); |
| } while (value1 != value2 && retry_limit-- > 0); |
| |
| H2W_DBG("value2 = %d (%d retries)", value2, (10-retry_limit)); |
| |
| hrtimer_start(&hi->btn_timer, hi->btn_debounce_time, HRTIMER_MODE_REL); |
| |
| return IRQ_HANDLED; |
| } |
| |
| #if defined(CONFIG_DEBUG_FS) |
| static int h2w_debug_set(void *data, u64 val) |
| { |
| mutex_lock(&hi->mutex_lock); |
| switch_set_state(&hi->sdev, (int)val); |
| mutex_unlock(&hi->mutex_lock); |
| return 0; |
| } |
| |
| static int h2w_debug_get(void *data, u64 *val) |
| { |
| return 0; |
| } |
| |
| DEFINE_SIMPLE_ATTRIBUTE(h2w_debug_fops, h2w_debug_get, h2w_debug_set, "%llu\n"); |
| static int __init h2w_debug_init(void) |
| { |
| struct dentry *dent; |
| |
| dent = debugfs_create_dir("h2w", 0); |
| if (IS_ERR(dent)) |
| return PTR_ERR(dent); |
| |
| debugfs_create_file("state", 0644, dent, NULL, &h2w_debug_fops); |
| |
| return 0; |
| } |
| |
| device_initcall(h2w_debug_init); |
| #endif |
| |
| static int h2w_probe(struct platform_device *pdev) |
| { |
| int ret; |
| struct h2w_platform_data *pdata = pdev->dev.platform_data; |
| |
| printk(KERN_INFO "H2W: Registering H2W (headset) driver\n"); |
| hi = kzalloc(sizeof(struct h2w_info), GFP_KERNEL); |
| if (!hi) |
| return -ENOMEM; |
| |
| atomic_set(&hi->btn_state, 0); |
| hi->ignore_btn = 0; |
| |
| hi->debounce_time = ktime_set(0, 100000000); /* 100 ms */ |
| hi->btn_debounce_time = ktime_set(0, 10000000); /* 10 ms */ |
| |
| hi->htc_headset_flag = 0; |
| hi->cable_in1 = pdata->cable_in1; |
| hi->cable_in2 = pdata->cable_in2; |
| hi->h2w_clk = pdata->h2w_clk; |
| hi->h2w_data = pdata->h2w_data; |
| hi->debug_uart = pdata->debug_uart; |
| hi->config_cpld = pdata->config_cpld; |
| hi->init_cpld = pdata->init_cpld; |
| hi->set_dat = pdata->set_dat; |
| hi->set_clk = pdata->set_clk; |
| hi->set_dat_dir = pdata->set_dat_dir; |
| hi->set_clk_dir = pdata->set_clk_dir; |
| hi->get_dat = pdata->get_dat; |
| hi->get_clk = pdata->get_clk; |
| hi->speed = H2W_50KHz; |
| /* obtain needed VREGs */ |
| if (pdata->power_name) |
| hi->vreg_h2w = vreg_get(0, pdata->power_name); |
| |
| mutex_init(&hi->mutex_lock); |
| |
| hi->sdev.name = "h2w"; |
| hi->sdev.print_name = h2w_print_name; |
| |
| ret = switch_dev_register(&hi->sdev); |
| if (ret < 0) |
| goto err_switch_dev_register; |
| |
| g_detection_work_queue = create_workqueue("detection"); |
| if (g_detection_work_queue == NULL) { |
| ret = -ENOMEM; |
| goto err_create_work_queue; |
| } |
| |
| ret = gpio_request(hi->cable_in1, "h2w_detect"); |
| if (ret < 0) |
| goto err_request_detect_gpio; |
| |
| ret = gpio_request(hi->cable_in2, "h2w_button"); |
| if (ret < 0) |
| goto err_request_button_gpio; |
| |
| ret = gpio_direction_input(hi->cable_in1); |
| if (ret < 0) |
| goto err_set_detect_gpio; |
| |
| ret = gpio_direction_input(hi->cable_in2); |
| if (ret < 0) |
| goto err_set_button_gpio; |
| |
| hi->irq = gpio_to_irq(hi->cable_in1); |
| if (hi->irq < 0) { |
| ret = hi->irq; |
| goto err_get_h2w_detect_irq_num_failed; |
| } |
| |
| hi->irq_btn = gpio_to_irq(hi->cable_in2); |
| if (hi->irq_btn < 0) { |
| ret = hi->irq_btn; |
| goto err_get_button_irq_num_failed; |
| } |
| |
| /* Set CPLD MUX to H2W <-> CPLD GPIO */ |
| hi->init_cpld(); |
| |
| hrtimer_init(&hi->timer, CLOCK_MONOTONIC, HRTIMER_MODE_REL); |
| hi->timer.function = detect_event_timer_func; |
| hrtimer_init(&hi->btn_timer, CLOCK_MONOTONIC, HRTIMER_MODE_REL); |
| hi->btn_timer.function = button_event_timer_func; |
| |
| ret = request_irq(hi->irq, detect_irq_handler, |
| IRQF_TRIGGER_LOW, "h2w_detect", NULL); |
| if (ret < 0) |
| goto err_request_detect_irq; |
| |
| /* Disable button until plugged in */ |
| set_irq_flags(hi->irq_btn, IRQF_VALID | IRQF_NOAUTOEN); |
| ret = request_irq(hi->irq_btn, button_irq_handler, |
| IRQF_TRIGGER_LOW, "h2w_button", NULL); |
| if (ret < 0) |
| goto err_request_h2w_headset_button_irq; |
| |
| ret = set_irq_wake(hi->irq, 1); |
| if (ret < 0) |
| goto err_request_input_dev; |
| |
| ret = set_irq_wake(hi->irq_btn, 1); |
| if (ret < 0) |
| goto err_request_input_dev; |
| |
| |
| |
| hi->input = input_allocate_device(); |
| if (!hi->input) { |
| ret = -ENOMEM; |
| goto err_request_input_dev; |
| } |
| |
| hi->input->name = "h2w headset"; |
| set_bit(EV_SYN, hi->input->evbit); |
| set_bit(EV_KEY, hi->input->evbit); |
| set_bit(KEY_MEDIA, hi->input->keybit); |
| set_bit(KEY_NEXTSONG, hi->input->keybit); |
| set_bit(KEY_PLAYPAUSE, hi->input->keybit); |
| set_bit(KEY_PREVIOUSSONG, hi->input->keybit); |
| set_bit(KEY_MUTE, hi->input->keybit); |
| set_bit(KEY_VOLUMEUP, hi->input->keybit); |
| set_bit(KEY_VOLUMEDOWN, hi->input->keybit); |
| set_bit(KEY_END, hi->input->keybit); |
| set_bit(KEY_SEND, hi->input->keybit); |
| |
| ret = input_register_device(hi->input); |
| if (ret < 0) |
| goto err_register_input_dev; |
| |
| return 0; |
| |
| err_register_input_dev: |
| input_free_device(hi->input); |
| err_request_input_dev: |
| free_irq(hi->irq_btn, 0); |
| err_request_h2w_headset_button_irq: |
| free_irq(hi->irq, 0); |
| err_request_detect_irq: |
| err_get_button_irq_num_failed: |
| err_get_h2w_detect_irq_num_failed: |
| err_set_button_gpio: |
| err_set_detect_gpio: |
| gpio_free(hi->cable_in2); |
| err_request_button_gpio: |
| gpio_free(hi->cable_in1); |
| err_request_detect_gpio: |
| destroy_workqueue(g_detection_work_queue); |
| err_create_work_queue: |
| switch_dev_unregister(&hi->sdev); |
| err_switch_dev_register: |
| printk(KERN_ERR "H2W: Failed to register driver\n"); |
| |
| return ret; |
| } |
| |
| static int h2w_remove(struct platform_device *pdev) |
| { |
| H2W_DBG(""); |
| if (switch_get_state(&hi->sdev)) |
| remove_headset(); |
| input_unregister_device(hi->input); |
| gpio_free(hi->cable_in2); |
| gpio_free(hi->cable_in1); |
| free_irq(hi->irq_btn, 0); |
| free_irq(hi->irq, 0); |
| destroy_workqueue(g_detection_work_queue); |
| switch_dev_unregister(&hi->sdev); |
| |
| return 0; |
| } |
| |
| |
| static struct platform_driver h2w_driver = { |
| .probe = h2w_probe, |
| .remove = h2w_remove, |
| .driver = { |
| .name = "h2w", |
| .owner = THIS_MODULE, |
| }, |
| }; |
| |
| static int __init h2w_init(void) |
| { |
| H2W_DBG(""); |
| return platform_driver_register(&h2w_driver); |
| } |
| |
| static void __exit h2w_exit(void) |
| { |
| platform_driver_unregister(&h2w_driver); |
| } |
| |
| module_init(h2w_init); |
| module_exit(h2w_exit); |
| |
| MODULE_AUTHOR("Laurence Chen <Laurence_Chen@htc.com>"); |
| MODULE_DESCRIPTION("HTC 2 Wire detection driver"); |
| MODULE_LICENSE("GPL"); |