[netdrvr] trim trailing whitespace: 8139*.c, epic100, forcedeth, tulip/*
diff --git a/drivers/net/tulip/winbond-840.c b/drivers/net/tulip/winbond-840.c
index 136a70c..64ecf929 100644
--- a/drivers/net/tulip/winbond-840.c
+++ b/drivers/net/tulip/winbond-840.c
@@ -38,12 +38,12 @@
Copyright (C) 2001 Manfred Spraul
* ethtool support (jgarzik)
* Replace some MII-related magic numbers with constants (jgarzik)
-
+
TODO:
* enable pci_power_off
* Wake-On-LAN
*/
-
+
#define DRV_NAME "winbond-840"
#define DRV_VERSION "1.01-d"
#define DRV_RELDATE "Nov-17-2001"
@@ -57,7 +57,7 @@
c-help-symbol: CONFIG_WINBOND_840
c-help: This driver is for the Winbond W89c840 chip. It also works with
c-help: the TX9882 chip on the Compex RL100-ATX board.
-c-help: More specific information and updates are available from
+c-help: More specific information and updates are available from
c-help: http://www.scyld.com/network/drivers.html
*/
@@ -207,7 +207,7 @@
*/
-
+
/*
PCI probe table.
@@ -374,7 +374,7 @@
static struct ethtool_ops netdev_ethtool_ops;
static int netdev_close(struct net_device *dev);
-
+
static int __devinit w840_probe1 (struct pci_dev *pdev,
const struct pci_device_id *ent)
@@ -434,7 +434,7 @@
np->mii_if.mdio_read = mdio_read;
np->mii_if.mdio_write = mdio_write;
np->base_addr = ioaddr;
-
+
pci_set_drvdata(pdev, dev);
if (dev->mem_start)
@@ -510,7 +510,7 @@
return -ENODEV;
}
-
+
/* Read the EEPROM and MII Management Data I/O (MDIO) interfaces. These are
often serial bit streams generated by the host processor.
The example below is for the common 93c46 EEPROM, 64 16 bit words. */
@@ -660,7 +660,7 @@
return;
}
-
+
static int netdev_open(struct net_device *dev)
{
struct netdev_private *np = netdev_priv(dev);
@@ -731,7 +731,7 @@
dev->name, np->phys[0]);
netif_carrier_on(dev);
}
-
+
if ((np->mii & ~0xf) == MII_DAVICOM_DM9101) {
/* If the link partner doesn't support autonegotiation
* the MII detects it's abilities with the "parallel detection".
@@ -761,7 +761,7 @@
result |= 0x20000000;
if (result != np->csr6 && debug)
printk(KERN_INFO "%s: Setting %dMBit-%s-duplex based on MII#%d\n",
- dev->name, fasteth ? 100 : 10,
+ dev->name, fasteth ? 100 : 10,
duplex ? "full" : "half", np->phys[0]);
return result;
}
@@ -947,7 +947,7 @@
iowrite32(i, ioaddr + PCIBusCfg);
np->csr6 = 0;
- /* 128 byte Tx threshold;
+ /* 128 byte Tx threshold;
Transmit on; Receive on; */
update_csr6(dev, 0x00022002 | update_link(dev) | __set_rx_mode(dev));
@@ -1584,7 +1584,7 @@
static void __devexit w840_remove1 (struct pci_dev *pdev)
{
struct net_device *dev = pci_get_drvdata(pdev);
-
+
if (dev) {
struct netdev_private *np = netdev_priv(dev);
unregister_netdev(dev);
@@ -1640,7 +1640,7 @@
spin_unlock_wait(&dev->xmit_lock);
synchronize_irq(dev->irq);
-
+
np->stats.rx_missed_errors += ioread32(ioaddr + RxMissed) & 0xffff;
/* no more hardware accesses behind this line. */